Double microporous layer cathode for membrane electrode assembly of passive direct methanol fuel cells

A novel membrane electrode assembly (MEA) is described that utilizes a double microporous layer (MPL) structure in the cathode of a passive direct methanol fuel cell (DMFC). The double MPL cathode uses Ketjen Black carbon as an inner-MPL and Vulcan XC-72R carbon as an outer-MPL. Experimental results indicate that this double MPL structure at the cathode provides not only a higher oxygen transfer rate, but enables more effective back diffusion of water; thus, leading to an improved power density and stability of the passive DMFC. The maximum power density of an MEA with a double MPL cathode was observed to be ca. 33.0 mW cm⁻², which is found to be a substantial improvement over that for a passive DMFC with a conventional MEA. A. C. impedance analysis suggests that the increased performance of a DMFC with the double MPL cathode might be attributable to a decreased charge transfer resistance for the cathode oxygen reduction reaction.     

Effect of operating conditions on the performance of a direct methanol fuel cell with PtRuMo/CNTs as anode catalyst

PtRu/CNTs and PtRuMo/CNTs catalysts have been synthesized by microwave-assisted polyol process and used as the anode catalysts for a direct methanol fuel cell (DMFC). The catalysts were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectrometry (XPS). The effect of different anode catalysts, membrane electrode assembly (MEA) activation, methanol concentration, methanol flow rate, oxygen flow rate and cell temperature on the DMFC performance has been investigated. The results show that the PtRu or PtRuMo particles with face-centered cubic structure are uniformly distributed on CNTs, and the addition of Mo to PtRu/CNTs makes the binding energies of each Pt species shift to lower values. PtRuMo/CNTs is a promising anode catalyst for DMFCs, and the appropriate operating conditions of the DMFC with PtRuMo/CNTs as the anode catalyst are MEA activation for 10 h, 2.0–2.5 M methanol at the flow rate of 1.0–2.0 mL/min, and oxygen at the flow rate of 100–150 mL/min. The DMFC performance increases significantly with an increase in cell temperature.     

Development of an advanced MEA to use high-concentration methanol fuel in a direct methanol fuel cell system

Despite serious methanol crossover issues in Direct Methanol Fuel Cells (DMFCs), the use of high-concentration methanol fuel is highly demanded to improve the energy density of passive fuel DMFC systems for portable applications. In this paper, the effects of a hydrophobic anode micro-porous layer (MPL) and cathode air humidification are experimentally studied as a function of the methanol-feed concentration. It is found in polarization tests that the anode MPL dramatically influences cell performance, positively under high-concentration methanol-feed but negatively under low-concentration methanol-feed, which indicates that methanol transport in the anode is considerably altered by the presence of the anode MPL. In addition, the experimental data show that cathode air humidification has a beneficial effect on cell performance due to the enhanced backflow of water from the cathode to the anode and the subsequent dilution of the methanol concentration in the anode catalyst layer. Using an advanced membrane electrode assembly (MEA) with the anode MPL and cathode air humidification, we report that the maximum power density of 78 mW/cm² is achieved at a methanol-feed concentration of 8 M and cell operating temperature of 60 °C. This paper illustrates that the anode MPL and cathode air humidification are key factors to successfully operate a DMFC with high-concentration methanol fuel.     

Enhanced performance of a passive direct methanol fuel cell with decreased Nafion aggregate size within the anode catalytic layer

The decrease in Nafion ionomer size within the anode catalytic layer for a passive direct methanol fuel cell (DMFC) results in a significant enhancement in fuel cell’s performance. Dynamic light scattering measurement demonstrates that the agglomerate size of Nafion ionomer in the solution decreases and the aggregate particle size distribution becomes narrow until a monodispersed Nafion ionomer was obtained with an increase in heat treatment temperature. The improved performance of the passive DMFC with smaller Nafion ionomer agglomerates within the anode catalytic layer can be ascribed to a decrease in charge-transfer resistance of anodic reaction obtained by electrochemical impedance analysis and to an improvement in catalyst utilization verified by cyclic voltammetric measurement. Furthermore, the small congeries formed between catalyst nanoparticles and Nafion ionomers could lead to a decrease in Nafion loading within the catalytic layer. This study confirms that the decrease in Nafion aggregation within the catalytic ink is beneficial to an improvement in both catalyst and Nafion ionomer utilization, thus enhancing fuel cell’s performance.     

Effect of the cathode open ratios on the water management of a passive vapor-feed direct methanol fuel cell fed with neat methanol

A novel approach has been proposed to improve the water management of a passive direct methanol fuel cell (DMFC) fed with neat methanol without increasing its volume or weight. By adopting perforated covers with different open ratios at the cathode, the water management has been significantly improved in a DMFC fed with neat methanol. An optimized cathode open ratio could ensure both the sufficient supply of oxygen and low water loss. While changing the open ratio of anode vaporizer can adjust the methanol crossover rate in a DMFC. Furthermore, the gas mixing layer, added between the anode vaporizer and the anode current collector to increase the mass transfer resistance, can improve the cell performance, decrease the methanol crossover, and increase the fuel efficiency. For the case of a DMFC fed with neat methanol, an anode vaporizer with the open ratio of 12% and a cathode open ratio of 20% produced the highest peak power density, 22.7 mW cm⁻², and high fuel efficiency, 70.1%, at room temperature of 25 ± 1 °C and ambient humidity of 25-50%.     

Microfluidic direct methanol fuel cell by electrophoretic deposition of platinum/carbon nanotubes on electrode surface

Carbon nanotubes (CNTs) supported platinum (Pt) nanoparticles prepared via electrophoretic deposition are used as catalyst layer of a microfluidic direct methanol fuel cell (DMFC), to study the influence of catalyst layer materials and deposition methods on the cell performance. A Y‐shaped channel is designed and microfabricated. It is verified by cyclic voltammetric measurements that shows ca. 317.7% increase in the electrochemical active surface area for the electrode with CNTs over that without CNT. Scanning electron microscopy observations indicate the network formation within the electrode because of a 3‐D structure of CNTs, which could be beneficial to the increasing electrode kinetics and to the improvement in fuel utilization. Comparison between the DMFCs with and without CNTs as support shows that the proof‐of‐concept microfluidic DMFC with Pt/CNTs electrode is able to reach a maximum power density of 5.70 mW cm^?2 at 25 °C, while the DMFC with plain Pt electrode only has a maximum power density of 2.75 mW cm^?2. Copyright © 2015 John Wiley & Sons, Ltd.     

Performance characteristics of a novel tubular-shaped passive direct methanol fuel cell

The present work consists of a tubular-shaped direct methanol fuel cell (DMFC) that is operated completely passively with methanol solution stored in a central fuel reservoir. The benefit of a tubular-shaped DMFC over a planar-shaped DMFC is the higher instantaneous volumetric power energy density (power/volume) associated with the larger active area provided by the tubular geometry. Membrane electrode assemblies (MEAs) with identical compositions were installed in both tubular and planar-shaped, passive DMFCs and tested with 1, 2, and 3 M methanol solutions at room temperature. The peak power density for the tubular DMFC was 19.0 mW cm⁻² and 24.5 mW cm⁻² while the peak power density for the planar DMFC was 20.0 mW cm⁻² and 23.0 mW cm⁻² with Nafion^® 212 and 115 MEAs, respectively. Even though the performance of the fuel cell improved with each increase in methanol concentration, the fuel and energy efficiencies decreased for both the tubular and planar geometries due to increased methanol crossover. The tubular DMFC experienced higher methanol crossover potentially due to a higher static fluid pressure in the anode fuel reservoir (AFR) caused by the vertical orientation of the tubular fuel reservoir. The performance of the tubular DMFC in this work represents an 870% improvement in power density from the previous best, passive, tubular DMFC found in the literature.     

Fabrication and impedance studies of DMFC anode incorporated with CNT-supported high-metal-content electrocatalyst

In this study, the fabrication of a direct methanol fuel cell (DMFC) anode with the incorporation of a multiwalled carbon nanotube (CNT)-supported high-metal-content Pt/Ru electrocatalyst, i.e., 40 wt%Pt-20 wt%Ru/CNT, using a novel approach and the resultant DMFC performances were investigated. Employing a vacuum filtration method, we were able to successfully fabricate the DMFC anode with a good electrode structure using an in-house prepared Pt-Ru/CNT electrocatalyst. The catalyst layer was formed directly on a Teflon-treated carbon cloth having a buckypaper texture with a catalyst loading of 4.0 mg cm⁻². From single-cell tests, excellent cell performances were obtained. At 80 °C, the power density was found to be as high as >100 mW cm⁻². This can be attributed to a thinner catalyst layer formed with a more efficient utilization of the catalyst than that using a low-metal-content counterpart, i.e., 20 wt%Pt-10 wt%Ru/CNT, as reported in an earlier study. However, the Nafion^® ionomer content in the catalyst layer played a key role in the anode fabrication to obtain a good cell performance. In addition, the electrochemical impedance spectroscopy (EIS) with a constant phase element (CPE)-based equivalent-circuit model was employed to analyze the fabricated anode. It distinctively revealed some specific characteristics in the resistances and the interface properties. Overall, the obtained impedance results are somewhat different from those of a conventional DMFC anode with the catalyst layer coated onto a porous gas diffusion layer (GDL) on a carbon backing material. Based on the experimental results and the impedance analyses, the high-metal-content Pt-Ru/CNT catalyst was found to be much more favorable and suitable for use as a DMFC anode catalyst.     

Effect of black catalyst ionomer content on the performance of passive DMFC

The effect of the ionomer content in the catalyst layers of both the anode and the cathode with the black catalyst on the performance of a passive DMFC was investigated in order to increase the power output of the passive DMFC. In situ cyclic voltammetry has been carried out to evaluate the electrochemically active surface area, ECSA and the catalyst utilization. Under the passive conditions, ionomer content had a significant effect on both the mass transport and the ECSA. The optimum ionomer content was affected by the operating current density whether at anode or at cathode. Under low current density region, i.e., activation over voltage region, 20 wt.% showed the highest performance at the anode and the cathode, and the cell performance in this region was varied in accordance with the results of the ECSA. Under high current density region, i.e., mass transport over voltage region, lower ionomer content, 10 and 15 wt.%, had the highest cell performance at the anode and the cathode, respectively. The decrease in the optimum ionomer content at high current density was related to the low mass transport of methanol at the anode, and the flooding at the cathode at the high ionomer contents. The optimum ionomer content whether at anode or at cathode was 20 wt.%, from the power density point of view. The catalyst utilization was 10% and 25% at optimum conditions at the cathode and the anode respectively.     

Effect of Nafion aggregation in the anode catalytic layer on the performance of a direct formic acid fuel cell

The effect of Nafion ionomer aggregation within the anode catalytic layer for a direct formic acid fuel cell (DFAFC) has been investigated. By simple heat treatment, the aggregation states of Nafion ionomers in aqueous solution can be tuned. Nafion agglomerate sizes in the solution decrease and aggregate size distribution becomes narrow with the increase in heat-treatment temperature. At a heat-treatment temperature of ca. 80 °C, nearly monodispersed Nafion ionomers corresponding to an aggregate size of ca. 25 nm in the solution are observed. The use of small Nafion ionomer agglomerates in the Nafion solution for anode catalytic layer significantly improves the performance of the passive DFAFCs. Impedance analysis indicates that the increased performance of the passive DFAFC with the anode using Nafion solution pretreated at elevated temperatures could be attributed to the decrease in charge-transfer resistance of the anode reaction. The decrease in Nafion aggregation within the catalyst ink leads to an increase in Nafion ionomer utilization within the catalyst layer and an improvement in catalyst utilization; thus enabling us to decrease Nafion loading within the anode catalytic layer but with slight improvement in DFAFC's performance.     

Design,fabrication and testing of a PMMA-based passive single-cell and a multi-cell stack micro-DMFC

A passive, air-breathing polymethyl methacrylate (PMMA) based single-cell and a multi-cell stack micro-direct methanol fuel cell (DMFC) with 1.0 cm² active area with a novel cathode plate structure and assembly layer are designed, fabricated and tested. The fuel cell is completely passive with no auxiliary device such as pump or fan. Oxygen is taken from the surrounding air, and the methanol solution is stored in a built-in reservoir. The performance of the single cell is tested with different methanol concentrations ranging from 1.0 M to 5.0 M, and the optimum performance is achieved by using methanol at a concentration of 4.0 M. A stack with 6 cells is fabricated and tested with the optimum methanol concentration of 4.0 M, and power levels produced by different catalyst loadings on the anode are compared. Besides, this study also considers the cost analysis of micro-DMFC. The combination of a catalyst loading of 3.0 mg cm⁻² Pt/Ru on the anode and 2.0 mg cm⁻² Pt on the cathode yield the highest power of 12.05 mW at 1.08 V and 11.2 mA. The total cost for the micro-DMFC in this study is only about USD 2 mW⁻¹.     

Performance of an integrated composite membrane electrode assembly in DMFC

We report here the performance of a metal-based integrated composite membrane electrode assembly (IC-MEA) in direct methanol fuel cell (DMFC). The IC-MEA integrates the multi-functions of a conventional MEA, gas diffusion layer (GDL) and current collector. It was fabricated by impregnating Nafion electrolyte into a sandwiched structure containing expanding-Polytetrafluoroethylene (e-PTFE) and porous titanium sheets and subsequently coating with catalyst layer and microporous layer (MPL). While operating with air and 2 M methanol under ambient pressure, the IC-MEA in DMFC can yield a maximum power density of 19 mW cm⁻² at 26 °C, higher than a in-house made Nafion 115 MEA under the same working conditions. The IC-MEAs has been successfully applied to planar multi-cell stacks.     

Effect of variation of hydrophobicity of anode diffusion media along the through-plane direction in direct methanol fuel cells

Reducing methanol crossover from the anode to cathode in direct methanol fuel cells (DMFCs) is critical for attaining high cell performance and fuel utilization, particularly when highly concentrated methanol fuel is fed into DMFCs. In this study, we present a novel design of anode diffusion media (DM) wherein spatial variation of hydrophobicity along the through-plane direction is realized by special polytetrafluoroethylene (PTFE) coating procedure. According to the capillary transport theory for porous media, the anode DM design can significantly affect both methanol and water transport processes in DMFCs. To examine its influence, three different membrane-electrode assemblies are fabricated and tested for various methanol feed concentrations. Polarization curves show that cell performance at high methanol feed concentration conditions is greatly improved with the anode DM design with increasing hydrophobicity toward the anode catalyst layer. In addition, we investigate the influence of the wettability of the anode microporous layer (MPL) on cell performance and show that for DMFC operation at high methanol feed concentration, the hydrophilic anode MPL fabricated with an ionomer binder is more beneficial than conventional hydrophobic MPLs fabricated with PTFE. This paper highlights that controlling wetting characteristics of the anode DM and MPL is of paramount importance for mitigating methanol crossover in DMFCs.     

Microwave assisted synthesis of surfactant stabilized platinum/carbon nanotube electrocatalysts for direct methanol fuel cell applications

Platinum electrocatalysts deposited on multi-walled carbon nanotubes (CNT) with high loading were prepared using a microwave-assisted polyol reduction method and employed for direct methanol fuel cells (DMFC). A zwitterionic surfactant was used as a stabilizing agent for the formation of Pt nanoparticles. A uniform and narrow size distribution of highly dispersed Pt nanoparticles could be achieved by adjusting the weight ratio of surfactant to Pt precursor allowing for Pt loadings of up to 60 wt%. The heating time and the temperature for the ethylene glycol (EG) oxidation were found to be the key factors for depositing Pt nanoparticles homogeneously on carbon nanotubes. The smallest average particle diameter of 1.8 nm was obtained through microwave heating to 140 °C in 50 s. The structure, amount and morphology of the electrocatalysts were characterized with XRD, TGA, and TEM, respectively. Single cell DMFC measurements were performed in a membrane-electrode assembly (MEA) with 5 cm² active area and very low catalyst loading (0.25 mg cm⁻² of noble metal on both anode and cathode). The DMFC performance of the surfactant stabilized cathode catalyst obtained by the new method described here revealed that the power density was three times higher than for a commercial catalyst used for comparison and two times higher than for an unstabilized CNT supported catalyst.     

An impedance study for the anode micro-porous layer in an operating direct methanol fuel cell

This study presents the benefit to an operating direct methanol fuel cell (DMFC) by coating a micro-porous layer (MPL) on the surface of anode gas diffusion layer (GDL). Taking the membrane electrode assembly (MEA) with and without the anodic MPL structure into account, the performances of the two types of MEA are evaluated by measuring the polarization curves together with the specific power density at a constant current density. Regarding the cell performances, the comparisons between the average power performances of the two different MEAs at low and high current density, various methanol concentrations and air flow rates are carried out by using the electrochemical impedance spectroscopy (EIS) technique. In contrast to conventional half cell EIS measurements, both the anode and cathode impedance spectra are measured in real-time during the discharge regime of the DMFC. As comparing each anode and cathode EIS between the two different MEAs, the influences of the anodic MPL on the anode and cathode reactions are systematically discussed and analyzed. Furthermore, the results are used to infer complete and reasonable interpretations of the combined effects caused by the anodic MPL on the full cell impedance, which correspond with the practical cell performance.     

Improved fuel use efficiency in microchannel direct methanol fuel cells using a hydrophilic macroporous layer

We demonstrate state-of-the-art room temperature operation of silicon microchannel-based micro-direct methanol fuel cells (μDMFC) having a very high fuel use efficiency of 75.4% operating at an output power density of 9.25 mW cm⁻² for an input fuel (3 M aqueous methanol solution) flow rate as low as 0.55 μL min⁻¹. In addition, an output power density of 12.7 mW cm⁻² has been observed for a fuel flow rate of 2.76 μL min⁻¹. These results were obtained via the insertion of novel hydrophilic macroporous layer between the standard hydrophobic carbon gas diffusion layer (GDL) and the anode catalyst layer of a μDMFC; the hydrophilic macroporous layer acts to improve mass transport, as a wicking layer for the fuel, enhancing fuel supply to the anode at low flow rates. The results were obtained with the fuel being supplied to the anode catalyst layer via a network of microscopic microchannels etched in a silicon wafer.     

Self-regulating passive fuel supply for small direct methanol fuel cells operating in all orientations

A microfluidic fuel supply concept for passive and portable direct methanol fuel cells (DMFCs) that operates in all spatial orientations is presented. The concept has been proven by fabricating and testing a passive DMFC prototype. Methanol transport at the anode is propelled by the surface energy of deformed carbon dioxide bubbles, generated as a reaction product during DMFC operation. The experimental study reveals that in any orientation, the proposed pumping mechanism transports at least 3.5 times more methanol to the reactive area of the DMFC than the stoichiometry of the methanol oxidation would require to sustain DMFC operation. Additionally, the flow rates closely follow the applied electric load; hence the pumping mechanism is self-regulating. Oxygen is supplied to the cathode by diffusion and the reaction product water is transported out of the fuel cell along a continuous capillary pressure gradient. Results are presented that demonstrate the continuous passive operation for more than 40 h at ambient temperature with a power output of p = 4 mW cm⁻² in the preferred vertical orientation and of p = 3.2 mW cm⁻² in the least favorable horizontal orientation with the anode facing downwards.     

Factors affecting methanol transport in a passive DMFC employing a porous carbon plate

The effect of the pore structure and thickness of the porous carbon plate, PCP, as well as the gas barrier thickness on the methanol transport and the performance of a passive DMFC under the different cell voltages of 0.1, 0.2 and 0.3 V using different methanol concentrations was investigated. As a result of the mass transfer restrictions by employing the PCP, high methanol concentrations over 20 M could be efficiently used to produce the relatively high power density of 30 mW cm⁻² for more than 10 h. The DMFC was operated under limiting current conditions in all the PCPs at 0.1 and 0.2 V to more than 20 M. The main factors for controlling the methanol transport were the barrier of the gas layer with CO₂, which was formed between the anode surface and the PCP and the properties of the PCP. At the low current densities of less than 60 mA cm⁻², when no CO₂ bubbles are emitted, both the pore structure and thickness of the PCP did not affect the methanol transport and the current voltage relationship. At the higher current densities, CO₂ bubbles were evolved through the PCP and different resistances to the methanol transport were observed depending on the PCP pore structure and thickness. The CO₂ gas layer between the MEA and the PCP caused a major resistivity for the methanol transport, and its resistivity increased with its thickness increasing. By using the PCP at 0.1 V, the energy density of the passive DMFC was significantly increased, e.g., more than seven times.     

The effect of Nafion content in a graphitized carbon nanofiber-based anode for the direct methanol fuel cell

The performance and stability of a direct methanol fuel cell (DMFC) with membrane electrode assemblies (MEA) using different Nafion^® contents (30, 50 and 70 wt% or MEA30, MEA50 and MEA70, respectively) and graphitized carbon nanofiber (GNF) supported PtRu catalyst at the anode was investigated by a constant current measurement of 9 days (230 h) in a DMFC and characterization with various techniques before and after this measurement. Of the pristine MEAs, MEA50 reached the highest power and current densities. During the 9-day measurement at a constant current, the performance of MEA30 decreased the most (−124 μV h⁻¹), while the MEA50 was almost stable (−11 μV h⁻¹) and performance of MEA70 improved (+115 μV h⁻¹). After the measurement, the MEA50 remained the best MEA in terms of performance. The optimum anode Nafion content for commercial Vulcan carbon black supported PtRu catalysts is between 20 and 40 wt%, so the GNF-supported catalyst requires more Nafion to reach its peak power. This difference is explained by the tubular geometry of the catalyst support, which requires more Nafion to form a penetrating proton conductive network than the spherical Vulcan. Mass transfer limitations are mitigated by the porous 3D structure of the GNF catalyst layer and possible changes in the compact Nafion filled catalyst layers during constant current production.     

Performance evaluation of passive direct methanol fuel cell with methanol vapour supplied through a flow channel

This work examines the effect of fuel delivery configuration on the performance of a passive air-breathing direct methanol fuel cell (DMFC). The performance of a single cell is evaluated while the methanol vapour is supplied through a flow channel from a methanol reservoir connected to the anode. The oxygen is supplied from the ambient air to the cathode via natural convection. The fuel cell employs parallel channel configurations or open chamber configurations for methanol vapour feeding. The opening ratio of the flow channel and the flow channel configuration is changed. The opening ratio is defined as that between the area of the inlet port and the area of the outlet port. The chamber configuration is preferred for optimum fuel feeding. The best performance of the fuel cell is obtained when the opening ratio is 0.8 in the chamber configuration. Under these conditions, the peak power is 10.2 mW cm⁻² at room temperature and ambient pressure. Consequently, passive DMFCs using methanol vapour require sufficient methanol vapour feeding through the flow channel at the anode for best performance. The mediocre performance of a passive DMFC with a channel configuration is attributed to the low differential pressure and insufficient supply of methanol vapour.