Microwave Dielectric Properties of Low-Fired Ba5Nb4O15

The effect of B₂O₃ on the sintering temperature and microwave dielectric properties of Ba₅Nb₄O₁₅ has been investigated using X-ray powder diffraction, scanning electron microscopy, and a network analyzer. Interactions between Ba₅Nb₄O₁₅ and B₂O₃ led to formation of second phases, BaNb₂O₆ and BaB₂O₄. The addition of B₂O₃ to Ba₅Nb₄O₁₅ resulted in lowering the sintering temperature from 1400° to 925°C. Low-fired Ba₅Nb₄O₁₅ could be interpreted by measuring changes in the quality factor ( Q × f ), the relative dielectric constant (ɛ_r), and the temperature coefficient of resonant frequency (τ_f) as a function of B₂O₃ additions. More importantly, the formation of BaNb₂O₆ provided temperature compensation. The microwave dielectric properties of low-fired Ba₅Nb₄O₁₅ had good dielectric properties: Q × f = 18700 GHz, ɛ_r= 39, and τ_f= 0 ppm/°C.     

Microstructures and Microwave Dielectric Characteristics of Ca(Zn1/3Nb2/3)O3 Complex Perovskite Ceramics

Ca(Zn_1/3Nb_2/3)O₃ microwave dielectric ceramics were prepared using a solid-state reaction process, and their microwave dielectric properties were evaluated as functions of sintering and postdensification annealing conditions. The relationship between microwave dielectric properties and processing was interpreted through the variation of microstructures. The dielectric constant showed slight variation with sintering and annealing conditions, but the Q × f value increased at first and then decreased with increased sintering temperature, and annealing in oxygen indicated significant improvement in Q × f , especially for the specimens sintered at higher temperatures. The good microwave dielectric properties were obtained in the ceramics sintered at 1225°C in air for 3 h and annealed at 1100°C in oxygen for 8 h: ɛ= 34.1, Q × f = 15 890 GHz, τ_f=−48 ppm/°C.     

Crystalline Structure and Dielectric Properties of Li1+x−yNb1−x−3yTix+4yO3M-Phase Solid Solutions

The structure and dielectric properties of the so-called M -phase solid solutions in the Li₂O–Nb₂O₅–TiO₂system have been investigated. Detailed studies of the lattice parameters of these phases agree well with structure models based on intergrowths of LiNbO₃slabs with a titanium-rich corundum-type layer. The relative permittivity ranges from ∼80 to ∼55; microwave quality factors increase with the titanium content, reaching values of Q × f = 9000 at 6 GHz. The temperature coefficient of the resonant frequency changes sign within the solid solution region, thus permitting tunability to a zero value. All the compositions can be sintered to high density at temperatures ≤1100°C.     

Microwave Dielectric Properties of Low-Fired ZnNb2O6 Ceramics with BiVO4 Addition

The BiVO₄ additive was found effective for low-temperature firing of ZnNb₂O₆ polycrystalline ceramics below 950°C in air without a serious degradation in their microwave dielectric properties. Dense BiVO₄-doped ZnNb₂O₆ samples of a relative sintered density over 95% could be prepared even at 925°C. An optimally processed specimen exhibited excellent microwave dielectric properties of Q · f = 55000 GHz, ɛ_r= 26, and τ_f=−57 ppm/°C. With increasing BiVO₄ addition up to 20 mol% relative to ZnNb₂O₆, while the quality factor Q · f was gradually decreased, the relative dielectric constant, ɛ_r, was linearly increased and the temperature coefficient of resonant frequency, τ_f, was slightly increased. The variations in Q · f and ɛ_r are surely attributable to the residual BiVO₄ in the ZnNb₂O₆ matrix. An unexpected slight increase in τ_f is probably due to the formation of the Bi(V,Nb)O₄-type solid solution.     

Microwave Dielectric Properties of Doped BaTi4O9

Polycrystalline BaTi₄O₉ doped with Mn, Sn, Zr, Ca, Sr, and Pb was prepared from carbonates and oxides. Single-phase ceramics with densities exceeding 97% of theoretical were made with up to 3 mol% Mn; 6 mol% Sn, Zr, and Ca; and 8 mol% Sr and Pb. Dielectric constant, k , quality factor, Q , and temperature coefficient of frequency, τ _f , of ∼37, 5675, and 15 ppm/°C, respectively, were determined at 4 GHz for undoped BaTi₄O₉. Doping did not significantly affect k and τ _f . However, doping with Mn, Sn, and Pb lowered Q , whereas doping with Zr, Ca, and Sr increased Q by up to 2000. Additions of 0.5 mol% MnO₂ as a second phase improved Q from 3675 to 7600.     

Origin of Microwave Dielectric Loss in ZnNb2O6-TiO2

(1− x )ZnNb₂O₆· x TiO₂ ceramics were prepared using both anatase and rutile forms of TiO₂. At a composition of x = 0.58, a mixture region of ixiolite (ZnTiNb₂O₈) and rutile was observed and the temperature coefficient of resonant frequency (τ_f) was ∼0 ppm/°C. We found that although ɛ_r and τ_f were comparable, the quality factor ( Q × f , Q ≈ 1/ tan δ, f = resonant frequency) of 0.42ZnNb₂O₆·0.58TiO₂ prepared from anatase and rutile was 6000 and 29 000, respectively. The origin of the difference in Q × f of both samples was investigated by measuring electrical conductivity and by analysis of the anatase–rutile phase transition. The anatase-derived sample had higher conductivity, which was related to the reduction of Ti⁴⁺. It is suggested that the increase of dielectric loss originates from an increase in Ti³⁺ and oxygen vacancies due to an anatase–rutile phase transition.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Correlation between Arrangement of Dielectric Layers and Microwave Dielectric Properties of Mg0.93Ca0.07TiO3−(Ca0.3Li0.14Sm0.42)TiO3 Ceramics

Effect of geometrical shape and induced thermal strain on the microwave dielectric properties of the layered structure ceramics of Mg_0.93Ca_0.07TiO₃ with (Ca_0.3Li_0.14Sm_0.42)TiO₃ was investigated as a function of the number of dielectric layers. The dielectric constant and the temperature coefficient of resonant frequency (TCF) were not changed significantly with the number of dielectric layers but only depended on the net compositional ratio. However, the dielectric loss quality was affected by the number of interfaces between dielectric layers, which had a partial composition inhomogeneity due to the diffusion of Mg²⁺ and Ti⁴⁺ ions. The dielectric loss quality also decreased with an increase of thermal strain induced to each dielectric layer.     

Compositional Dependence of Microwave Dielectric Properties in (1 −x)(Na1/2Nd1/2)TiO3−xNd(Mg1/2Ti1/2)O3 Ceramics

The compositional dependence of microwave dielectric properties has been investigated in the (1 − x )(Na_1/2Nd_1/2)TiO₃− x Nd(Mg_1/2Ti_1/2)O₃ (NNT-NMT) system. The addition of NMT results in significant improvement in the quality factor and the temperature coefficient of frequency, but gradually decreases the dielectric constant from ∼100 for pure NNT to ∼25 for pure NMT. The single perovskite phase is observed with various { hkl } superlattice reflections over the entire compositional range. The increasing tendency of peak splitting with increasing x at some perovskite reflections strongly suggests that the crystal structure of the system changes to lower symmetry structures. This is confirmed using infrared reflectivity spectra. The superlattice reflections related to structural deviation become more predominant as the composition reaches pure NMT. Particularly, {111} superlattice reflections are believed to be associated with the 1:1 cation ordering and responsible for the observed abrupt increase in quality factor at x > 0.7.     

Microwave Dielectric Properties and Far-Infrared Reflectivity Characteristics of the CaTiO3–Li(1/2)−3xSm(1/2)+xTiO3Ceramics

Microwave dielectric properties and far-infrared reflectivity spectra of the 0.3CaTiO₃–0.7Li_{(1/2)−3 x} Sm_{(1/2)+ x} TiO₃ ceramics were investigated as a function of Sm³⁺ substitution (0.0 ≤ x ≤ 0.12). The dielectric constant decreased as the Sm³⁺ substitution increased. The Q × f value increased, up to a solid-solution limit at x = 0.11, because of the change of vibration modes between the A-site cation and the TiO₆ octahedron, and then decreased because of the formation of a secondary phase (Sm₂Ti₂O₇). On the analysis of the far-infrared reflectivity spectra, in the 50–4000 cm⁻¹ range, the change of the dielectric loss and dielectric constant could be explained by the intrinsic factor.     

Microstructure and Microwave Dielectric Properties of Ba(Zn1/3Ta2/3)O3 Ceramics with ZrO2 Addition

The effect of ZrO₂ on crystallographic order, microstructure, and microwave dielectric properties of Ba(Zn_1/3Ta_2/3)O₃ (BZT) ceramics was investigated. A small amount of ZrO₂ disturbed the 1:2 cation ordering. The average grain size of the BZT significantly increased with the addition of ZrO₂, which was attributed to liquid-phase formation. The relative density increased with the addition of a small amount of ZrO₂, but it decreased when the ZrO₂ content was increased. Variation of the dielectric constant with ZrO₂ addition ranged between 27 and 30, and the temperature coefficient of resonant frequency increased abruptly as the ZrO₂ amount exceeded 2.0 mol%. The Q value of the BZT significantly improved with the addition of ZrO₂, which could be explained by the increased relative density and grain size. The maximum Q × f value achieved in this investigation was ∼164 000 GHz for the BZT with 2.0 mol% ZrO₂ sintered at 1550°C for 10 h.     

Dielectric Properties of the Fluorite-like Bi2O3–Nb2O5 Solid Solution and the Tetragonal Bi3NbO7

Our analysis of the microwave dielectric properties of the δ-Bi₂O₃–Nb₂O₅ solid solution (δ-BN_ss) showed a continuous increase in permittivity and dielectric losses with an increasing concentration of Nb₂O₅. The only discontinuity was found for the temperature coefficient of resonant frequency, which is negative throughout the entire homogeneity range but reaches a minimum value for the sample with 20 mol% Nb₂O₅. At the same composition there is a discontinuity in the grain size of the δ-BN_ss ceramics. For the sample containing 25 mol% Nb₂O₅ two structural modifications were observed. A single-phase tetragonal Bi₃NbO₇, in the literature referred to as a Type-III phase, is formed in a very narrow temperature range from 850° to 880°C. A synthesis performed below or above this temperature range resulted in the formation of the end member of the δ-BN_ss homogeneity range. Compared with the δ-BN_ss the Bi₃NbO₇ ceramics exhibit lower microwave dielectric losses, an increased conductivity, and a positive temperature coefficient of resonant frequency.     

Bismuth/Samarium Cosubstituted Ba6−3xNd8+2xTi18O54 Microwave Dielectric Ceramics

Modification of the microwave dielectric properties in Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ ( x = 0.5) solid solutions by Bi/Sm cosubstitution for Nd was investigated. A large increase in the dielectric constant and near-zero temperature coefficient combined with high Qf values were obtained in modified Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ solid solutions where an enlarged solid solution limit of Bi in Ba_{6−3 x} Nd_{8+2 x} Ti₁₈O₅₄ was observed. Excellent microwave dielectric characteristics (ɛ= 105, Qf = 4110 GHz, and very low τ_f) were achieved in the composition Ba_{6−3 x} (Nd_0.7Bi_0.18Sm_0.12)_{8+2 x} Ti₁₈O₅₄.     

Atmospheric Dependence on Dielectric Loss of 1/6Ba5Nb4O15· 5/6BaNb2O6 Ceramics

Samples of 1/6Ba₅Nb₄O₁₅·5/6BaNb₂O₆ along with the pure end members, Ba₅Nb₄O₁₅ and BaNb₂O₆, were sintered under low oxygen partial pressure. The degradation mechanisms of dielectric loss in this reducing atmosphere have been studied. We found that the degradation occurred primarily due to the formation of oxygen vacancies caused by the reduction of Nb⁵⁺. This was determined by measuring the electrical conductivity, and through X-ray photoelectron spectroscopy. More importantly, the dielectric loss of 1/6Ba₅Nb₄O₁₅·5/6BaNb₂O₆ samples with higher temperature stability was further decreased on sintering in a reducing atmosphere. This observation has been explained by considering the increased porosity and formation of a reduced second phase, Ba_0.65NbO₃.     

Kinked Grain Boundaries in Alumina Doped with Y2O3

Polycrystalline alumina specimens with and without MgO doping show smoothly curved grain boundaries after heat treatment at 1400°C indicating their rough structure. When heat-treated at 1400° and 1500°C for 24 h after packing in an alumina–YAG powder mixture, many grain boundaries (without any liquid phase) develop kinks of large and small scales as observed by scanning electron microscopy and transmission electron microscopy. The addition of Y₂O₃ at concentrations close to the solubility limit is thus shown to induce the grain boundary transition to singular structures.     

Low-Fire Processing of ZrO2–SnO2–TiO2 Ceramics

Effects of a liquid-phase-sintering aid, BaCuO₂+ CuO (BCC), on densification and microwave dielectric properties of (Zr_0.8Sn_0.2)TiO₄ (ZST) ceramics have been investigated. The densification kinetics of ZST are greatly enhanced with the presence of 2.5–5 wt% BCC, but become retarded when the amount of BCC increases further. At a given BCC content, moreover, slower densification kinetics are observed with a larger particle size of ZST. The above results are attributed to a chemical reaction taking place at the interface of BCC/ZST during firing. The ZST dissolves into BCC, forming crystalline phases of ZrO₂, SnO₂, CuO, and BaTi₈O₁₆ which reduce the amount of BCC flux available for liquid-phase sintering. The crystallization kinetics become more significant, compared with densification kinetics, with increasing the amount of BCC and the particle sizes of ZST. For samples with 2.5–5 wt% BCC, a high relative sintered density is obtained at 1000°C and the resulting microwave ceramics have a dielectric constant and a value of Q at 7 GHz in the ranges of 35–38 and 2800–5000, respectively.     

Structure and Microwave Dielectric Properties of (Zn1−xCox)TiO3 Ceramics

Dielectric ceramics in the system (Zn_{1− x} Co _x )TiO₃ ( x = 0–1) were synthesized by the solid-state reaction route. The phase distribution, microstructure, and dielectric properties were characterized by using powder X-ray diffraction analysis, electron microscopy, and microwave measurement techniques. Three phase composition regions were identified in the specimens sintered at 1150°C; [spinel + rutile] at 0 ≤ x ≤ 0.5, [spinel + ilmenite + rutile] at 0.5 < x ≤ 0.7, and [ilmenite] phase at 0.7 < x ≤ 1. For the 0 ≤ x ≤ 0.5 region, the amount of Ti-rich precipitates incorporated into the spinel phase decreased with the Co content at 0 ≤ x ≤ 0.5, with a concomitant increase of the rutile phase. The ilmenite phase appeared for high Co content. The microwave dielectric properties depended on the phase composition and volume according to the three phase regions, where the relative amount of rutile to the spinel or ilmenite determined the dielectric properties. The dielectric constant as a function of Co addition was modeled with a Maxwell mixing rule. An optimum phase distribution was determined in this system with dielectric constant of 25, a Q * f 70 000 GHz, and a low temperature coefficient of the resonant frequency.