Characteristics of critical current of superconducting solenoid wound with the stacked tape

The high-T_c superconducting (HTS) magnet is an important element for developing HTS power equipments such as the dc reactor of the inductive type superconducting fault current limiter (SFCL). In order to use the HTS magnet for the large-scale power system, its critical current needs to be high enough. Generally, the double pancake HTS magnet has the severe decrease in the critical current because of magnetic field perpendicular to the tape surface. To fabricate a high critical current magnet, we wound a solenoid with the stacked tape. In this paper, the characteristics of the critical current of the HTS solenoid wound with the stacked tape were investigated. The results of this research can be used as the background data for the design of the large-scale HTS magnet.     

Reduction of fault current peak in an inductive high-Tc superconducting fault current limiter

This paper dealt with current-limiting performances of an inductive high-T_c superconducting fault current limiter with an auxiliary coil. The fault current limiter mainly consists of the primary copper coil, secondary high-T_c superconducting rings, and auxiliary high-T_c superconducting coils, which are magnetically coupled through three-legged core. The superconducting fault current limiter as a series element in the power system is inserted to limit the fault current. The device presents fast variable-impedance features in the event of a fault condition. The fault current peak can become relatively large for certain ranges of the flux and the fault instant due to the core saturation. The auxiliary coil proposed in this paper was proven to increase the impedance of the SFCL up to more than 31% while preventing the core saturation.     

Dc bias system of a 35 kV/90 MVA saturated iron core SFCL

Saturated iron core superconducting fault current limiter (SIC-SFCL) is a promising fault current limiting device for high or extra-high voltage power grids. It has low impedance in normal power transmission and turns high impedance when a short-circuit takes place. The dc bias system of a saturated iron core superconducting fault current limiter plays a key role in realizing these features. Our 35 kV/90 MVA SIC-SFCL has been running live-grid since January 2008 at Puji substation in Yunnan, China. In this paper, the working principle of the dc bias system will be introduced and results of artificially imposed short-circuit tests will be provided, which verifies the validity of this system.     

Current distribution measurement in YBCO thin film for a superconducting fault current limiter

Current distribution in the superconducting film for a resistive fault current limiter is important, because it influences AC loss and a uniformity of S/N transition. The lateral current distribution of the film was reconstructed from the magnetic field distribution which is measured by multiple Hall probes. The following results were obtained. (1) Non-uniform current distribution in the superconducting film was observed when the current was less than 1.3 times of critical current (I_c). (2) The current in a superconducting film was uniform when the current was much higher than I_c. The current can be considered uniform when the film works as a fault current limiter, because the S/N transition starts about twice of I_c. (3) The validity of the measurement was verified by the comparison with the electric circuit simulation.     

Comparative Study of Resistive and Inductive Superconducting Fault Current Limiters SFCL for Power System Transient Stability Improvement

This paper presents a comparative study of resistive and inductive superconducting fault current limiter (SFCL) for power systems transient stability improvement. Two applications of transient stability assessment are presented in this paper: The first shows the efficiency of the resistive and inductive SFCL in series with a generator, the second uses SFCL installed in series with a transmission line. SFCL can just be operated during the period from the fault occurrence to the fault clearing; the modeling and the effect of SFCL has been investigated to have higher benefits for the power system. In the present work, modification of the admittance matrix method is used for modeling of SFCL; Critical Clearing Time (CCT) has been used as an index for evaluated transient stability. The transient stability is assessed by the criterion of relative rotor angles, using the Runge–Kutta method. The effectiveness of the proposed method is tested on the WSCC3 nine-bus system applied to the case of three-phase short circuit fault in one transmission line. A simulation and comparison are presented in this document.     

Proposal of rectifier type superconducting fault current limiter with non-inductive reactor (SFCL)

A rectifier type superconducting fault current limiter (SFCL) with non-inductive reactor has been proposed. The concept behind this SFCL is the appearance of high impedance during non-superconducting state of the coil. In a hybrid bridge circuit, two superconducting coils connected in anti-parallel: a trigger coil and a limiting coil. Both the coils are magnetically coupled with each other and have same number of turns. There is almost zero flux inside the core and therefore the total inductance is small during normal operation. At fault time when the trigger coil current reaches to a certain level, the trigger coil changes from superconducting state to normal state. This super-to-normal transition of the trigger coil changes the current ratio of the coils and therefore the flux inside the reactor is no longer zero. So, the equivalent impedance of both the coils increased thus limits the fault current. We have carried out computer simulation using EMTDC and observed the results. A preliminary experiment has already been performed using copper wired reactor with simulated super-to-normal transition resistance and magnetic switches. Both the simulation and preliminary experiment shows good results. The advantage of using hybrid bridge circuit is that the SFCL can also be used as circuit breaker. Two separate bridge circuit can be used for both trigger coil and the limiter coil. In such a case, the trigger coil can be shutdown immediately after the fault to reduce heat and thus reduce the recovery time. Again, at the end of fault when the SFCL needs to re-enter to the grid, turning off the trigger circuit in the two-bridge configuration the inrush current can be reduced. This is because the current only flows through the limiting coil. Another advantage of this type of SFCL is that no voltage sag will appear during load increasing time as long as the load current stays below the trigger current level.     

Experimental analysis of AC loss and recovery characteristics for proposal of effective thickness of spacers in pancake type

For the design of superconducting fault current limiter, the research about recovery time and AC loss is essential issue because this characteristic is closely related to stability and efficiency. In general, superconducting fault current limiter (SFCL) modules can be made into pancake or solenoid type coil. While the pancake type coil has smaller AC loss, it has longer recovery time compared with the solenoid type coil. In this paper, a new pancake type coil was proposed to decrease recovery time by improving their cryogenic condition. A new pancake type coil is made with spacers between adjacent superconducting tapes. However, as the thickness of the spacer was increased, the AC loss was increased unlike the recovery characteristic. From the experimental results, our group confirmed that the pancake type coil with the spacer has trade-off relationship between AC loss and recovery characteristics with the spacer thickness.The proposed results in this paper would be utilized to design superconducting fault current limiters.     

The fault current limiting characteristics of a flux-lock type high-Tc superconducting fault current limiter using series resonance

We analyzed the fault current limiting characteristics of a flux-lock type high-T_c superconducting fault current limiter (HTSC-FCL) using series resonance between capacitor for series resonance and magnetic field coil which was installed in coil 3. The capacitor for the series resonance in the flux-lock type HTSC-FCL was inserted in series with the magnetic field coil to apply enough magnetic field into HTSC element, which resulted in higher resistance of HTSC element.However, the impedance of the flux-lock type HTSC-FCL has started to decrease since the current of coil 3 exceeded one of coil 2 after a fault accident. The decrease in the impedance of the FCL causes the line current to increase and, if continues, the capacitor for the series resonance to be destructed. To avoid this operation, the flux-lock type HTSC-FCL requires an additional device such as fault current interrupter or control circuit for magnetic field.This paper investigated the parameter range where the operation as mentioned above for the designed flux-lock type HTSC-FCL using series resonance occurred from the experimental results. In the design of the flux-lock type HTSC-FCL, the some methods to avoid the continuous increase of the line current were suggested and confirmed by the experiments that the suggested methods were available to prevent the continuous increase of the line current after a fault happened.     

Surface flashover characteristics in liquid nitrogen for application of superconducting pancake coils

For the development of superconducting power apparatus, it is necessary to establish the dielectric technology in coolants like LN₂. Among the dielectric technology, surface flashover characteristics are studied with several simplified spacers at the structural aspects. Double pancake coil can apply to transformer and fault current limiter, etc. To design dielectric system of high temperature superconducting transformer consisting of double pancake coils, this study discusses an effective insulator composition. Circular shape insulator divided into two parts should be inserted between coils and the insulator should cover electric stresses concentrated at the circumference of the coils which are in the same section of double pancake coils facing each other.     

Development of a superconducting fault current limiter using various high-speed circuit breakers

The authors constructed and tested a model superconducting fault current limiter (SFCL) using a high-temperature superconducting film according to a design that includes a vacuum interrupter with an electromagnetic repulsion mechanism. The superconductor and the vacuum interrupter are connected in parallel with a bypass coil. If a fault occurs and current flows through the system, the superconductor is quenched and the current is transferred to the parallel coil because of the voltage drop in the superconductor. This large current in the parallel coil actuates the magnetic repulsion mechanism of the vacuum interrupter. On opening the vacuum interrupter, the current in the superconductor is interrupted. This model is expected to exhibit very low-energy consumption by the superconductor. The authors succeeded in interrupting the current flowing in the superconductor within a half-cycle using a prototype SFCL. An improved SFCL with higher voltage and current ranges was used to carry out current-limiting tests and to investigate the possibility of adapting our SFCL in a power system. The authors also carried out a currentlimiting test using a conventional high-speed vacuum circuit breaker (HSVCB) as a new method for realising our concept.     

Critical current in YBa2Cu3O7 ceramics

Measurements of critical currents using a four-point direct current (dc) method and an alternating magnetic field method have been performed on several superconducting YBa₂Cu₃O₇ ceramics at 77 K. In the presence of a constant magnetic field, the critical currents obtained with the alternating field method are several orders of magnitude larger than the critical currents measured by the dc method. Also, we observed a minimum in the dc critical current as a function of applied transverse magnetic field. Several authors have suggested that these ceramics behave as individual superconducting grains coupled by Josephson junctions. In this paper, we explain the two observations above using that model.     

14 kV single-phase superconducting fault current limiter based on YBCO films

We present the fabrication and short circuit test results of a 14 kV single-phase resistive superconducting fault current limiter (SFCL) based on YBa₂Cu₃O₇ (YBCO) films. Individual components were processed using the 4″ YBCO films and have the rated voltage and current of 600 V and 35 A at 77 K, respectively. Twenty four components, eight components in series and three lines in parallel, make a module having the rated voltage and current of 4.8 kV and 105 A, respectively. Three modules were assembled in series to produce the SFCL working at 77 K, a 14 kV single-phase machine for the 22.9 kV Y-Y grid. short circuit tests were successfully conducted in an accredited test facility with the maximum fault currents up to 14.1 kA_P. All components quenched together upon faults and shared the rated voltage evenly without any supplementary device between the modules. This proves that the SFCL based on YBCO films may not only work reliably at 22.9 kV, but also provide technical feasibility for higher voltage application including the transmission grids.     

Analysis on the thermal and electrical characteristics of impregnating materials for the bifilar winding-type superconducting fault current limiter

The resistive type high temperature superconducting fault current limiter (HTSFCL) limits the fault current with the resistance that generated by fault current. The generated resistance by fault current makes large pulse power which makes the operation of HTSFCL unstable. So, the cryogenic cooling system of the resistive type HTSFCL must diffuse and eliminate the pulse energy very quickly. Although the best way is to make wide direct contact area between HTS winding and coolant as much as possible, HTS winding also need the impregnation layer which fixes and protects it from electromagnetic force. This paper deals with thermal conductivity and dielectric strength of some epoxy compounds for the impregnation of high temperature superconducting (HTS) winding at 77 K. The measured data can be used in the optimal design of impregnation for HTS winding. Aluminar filling increased the thermal conductivity of epoxy compounds. Hardener also affected the thermal conductivity and the dielectric strength of epoxy compounds.     

Proposal of DC shield reactor type superconducting fault current limiter

Saturated DC reactor type superconducting fault current limiter (SFCL) had been proposed two years ago. It was classified to rectifier type SFCL. The changing inductance value with the operating mode has superior characteristics to reduce voltage sag during step increase of the load current. But it has the disadvantage of its weight. In this paper, rectifier type SFCL with shielded reactor has been proposed. The reactor which has superconducting ring or tube inside its winding is substituted to the DC link of the rectifier. The configuration looks like an air core transformer with secondary short winding. When the current through the bulk shield-ring reaches to a certain level, the flux penetrates to the shield body and finite impedance appears in the primary winding. In other words, when the surface flux density exceeds its critical flux density, the flux penetrates into the bulk superconductor, and increases equivalent inductance. The equivalent transient resistance of the shield was represented as a function of exponential of the time. Using this equivalent transient resistance, the transient impedance was expressed. The transient wave analysis using EMTDC (electro-magnetic transients in DC systems) has been described. Simulated waveforms are shown considering the source inductance, the leakage inductance, the coupling coefficient and the forward voltage drop of the semiconductor. And voltage sag was also investigated with 50% step load increase.Preliminary design was also performed. The coil size and number of turns are designed to obtain adequate inductance for the current limitation, and the central magnetic field of the coils are calculated. There is optimal aspect ratio to minimize the magnetic field with restriction in outer diameter of the coil.     

Analysis on the Fusion Technology of a Commercial Transformer and an SFCL

In this study, a new concept is proposed on a combination device with functions of a commercial transformer and a superconducting fault current limiter (SFCL). This device serves as a transformer by stepping the voltage up or down in normal condition. When a transient phenomenon occurs in the power system, it serves as an SFCL to limit the fault current. The device quickly detects the line current using a current transformer (CT), and is based on the high-speed, silicon-controlled rectifier (SCR) interrupter operation. This is done by identifying the fault using an SCR switching control system. The test results showed that the fault current was limited by the impedance of the superconducting element a half cycle after a fault occurred. An SCR that initially had a normally open contact was turned on within a half cycle. However, an SCR with a normally close contact was turned off after a half cycle because the current dropped below the holding current after a half cycle. The voltage of the superconducting element was low in the step-down turn ratio condition of the transformer. This was because the secondary and tertiary windings were connected in series due to the SCR-1 turn-off condition, and the sum of voltages on each winding appeared on the superconducting element. By combining the existing power device technology and an SFCL technology, it is expected that the existing problems of an SFCL can be addressed to construct a smart power system.     

Development,Updating and Long-Term Operations of a 10.5 kV HTS Fault Current Limiter

There are many irreplaceable advantages of high temperature superconducting (HTS) fault current limiter, applying in electric utilities. It is expected to be able to solve excessive fault current problems and to enhance safety and stability of power systems. In this paper, the R and D of an improved bridge-type 10.5 kV three-phase superconducting fault current limiter (SFCL) was present. Each phase adopted a HTS coil with inductance of 6.2 mH. The three coils wound with 8,571 m Bi2223/Ag tapes totally. After installation at a 110 kV/10.5 kV substation in Hunan Province of China, the performances of the whole SFCL were tested, including a three-phase-to-ground short circuit experiment at the pre-setup short circuit point. And then, the SFCL was put into operations in the 10.5 kV power grids for more than 11000 h. About 3 years later, the SFCL was moved, reinstalled, and put into operation again since February 16 of 2011 at a 10.5-kV superconducting power substation located in Baiyin, Gansu Province of China. In this paper, the redesigned and manufactured cryostats with nonmagnetic stainless steel, tests, and long-term operations of the SFCL in 10.5 kV power grids were also described in detail.     

Sub-cooled nitrogen cryogenic cooling system for superconducting fault current limiter by using GM-cryocooler

The 21st Century Frontier R&D Program was planned to develop and commercialize the inductive Superconducting Fault Current Limiter (SFCL) in Korea until 2011. The 1.2 kV/80 A inductive SFCL was planned to develop at the first year in the first phase (2001-2002) and the 6.6 kV/200 A inductive SFCL for short run operation test was planned to develop at the second and third year in the first phase (2002-2004). The experimental characteristics of conduction-cooled cooling system developed in the first year was very weak from the sudden large thermal disturbance. Therefore, the conduction-cooled cooling system was concluded not appropriate for the cryogenic technology of the application of superconducting fault current limiter. In the third year research, the improved sub-cooled nitrogen cooling system was adopted and investigated.In this paper, the characteristics of each cooling type was compared and the basic deign of ameliorated cooling system was introduced and the total heat load of the cooling system was calculated and compared with the heat load of the cooling system developed at 2nd year research.     

On conduction-cooling of a high-temperature superconducting cable

Current generation high-temperature superconducting (HTS) power transmission cables use liquid nitrogen as a coolant that circulates along the cable. In this work, the use of axial conduction-cooling in attaining HTS temperatures in transmission lines is proposed. Liquid coolant use is envisioned only at periodic length intervals along the transmission lines, in combination with insulation and copper. The proposed concept is feasible due to the high thermal conductivity of pure copper at cryogenic temperatures. A basic design for the insulated cable is proposed and a detailed numerical simulation of heat transfer in such a cable is carried out for various case studies considering the superconducting materials MgB₂ and BSCCO-2223.     

Resistance varying characteristics of DC superconducting fault current limiter in MTDC system

Recent years, voltage source converter-based multi-terminal high voltage DC power transmission (MTDC) is widely developed in the world. However, it is difficult for the existing DC breaker to cut off the fault transmission line with large short-circuit fault current. Then, it would be helpful to develop DC fault current limiter for the MTDC system. In this paper, DC superconducting fault current limiter (DCSFCL) is proposed to limit fault current. In order to study the resistance-time performance of the DCSFCL under the rapid change of fault current, a simulation model of Zhoushan MTDC system with DCSFCL is established, and the current-limiting performance of the DCSFCL at different location of the grid is studied. The simulation results show that DCSFCL can effectively limit short-circuit current and improve the operation reliability of MTDC system.     

Prototype Fault Current Limiter Using Transformer and a Modular Device of YBCO Coated Conductor

A superconducting fault current limiter (SCFL) consisted of a transformer with low reactance connected to the power line and with the secondary winding short-circuited by a modular superconducting limiter device with 16 elements connected in series was constructed and tested. The designed coupling transformer has low dispersion reactance in order to limit the voltage drop in the power line within the range of 5 % to 10 %. The experimental results showed that an insertion of a 0.125 Ω resistance limited the peak current to a factor of 2.5 times of the unlimited current. The power dissipation reached 39 kW during 100 ms, with an energy density of 380 J/cm³. Based on these results, the SCFL will be further tested in a 3 MVA (15 kV/380 V) generator for currents up to 10 kA.