Bolted Joints in Three Axially Braided Carbon Fibre/Epoxy Textile Composites with Moulded-in and Drilled Fastener Holes

Experimental behaviour of bolted joints in triaxial braided (0°/±45°) carbon fibre/epoxy composite laminates with drilled and moulded-in fastener holes has been investigated in this paper. Braided laminates were manufactured by vacuum infusion process using 12 K T700S carbon fibres (for bias and axial tows) and Araldite LY-564 epoxy resin. Moulded-in fastener holes were formed using guide pins which were inserted in the braided structure prior to the vacuum infusion process. The damage mechanism of the specimens was investigated using ultrasonic C-Scan technique. The specimens were dimensioned to obtain a bearing mode of failure. The bearing strength of the specimens with moulded-in hole was reduced in comparison to the specimens with drilled hole, due to the increased fibre misalignment angle following the pin insertion procedure. An improvement on the bearing strength of moulded-in hole specimens might be developed if the specimen dimensions would be prepared for a net-tension mode of failure where the fibre misalignment would not have an effect as significant as in the case of bearing failure mode, but this mode should be avoided since it leads to sudden catastrophic failures.     

基于纤维束/环氧树脂复合材料试验的单向层合板横向拉伸强度预测方法

实验研究表明,纤维束/环氧树脂复合材料试件的横向拉伸强度与工程上常用的单向层合板横向拉伸强度在趋势上具有很好的相关性,但是数值上存在一定差距。本文使用两种碳纤维和两种环氧树脂制备了三种纤维束/环氧树脂复合材料和单向层合板,并分别测量了纤维束/环氧树脂复合材料和单向层合板的横向拉伸强度,以及环氧基体的拉伸强度。在实验基础上,应用Griffith断裂强度理论建立了纤维束/环氧树脂复合材料和单向层合板的横向拉伸强度的关系模型,通过两种复合材料实验的结果拟合了该模型中的参数。利用第三种复合材料实验进行校验,发现该模型预测的单向层合板横向拉伸强度与实测强度之间达到很好的一致性,相对偏差为9%。采用本文提出的方法,可以用较为简单的纤维束/环氧树脂复合材料和环氧基体拉伸试验预测单向层合板的横向拉伸强度。     

CF/EP composite laminates with carbon black and copper chloride for improved electrical conductivity and interlaminar fracture toughness

An experimental study was conducted to improve the electrical conductivity of continuous carbon fibre/epoxy (CF/EP) composite laminate, with simultaneous improvement in mechanical performance, by incorporating nano-scale carbon black (CB) particles and copper chloride (CC) electrolyte into the epoxy matrix. CF/EP laminates of 65 vol.% of carbon fibres were manufactured using a vacuum-assisted resin infusion (VARI) technique. The effects of CB and the synergy of CB/CC on electrical resistivity, tensile strength and elastic modulus and fracture toughness (K_IC) of the epoxy matrix were experimentally characterised, as well as the transverse tensile modulus and strength, Mode I and Mode II interlaminar fracture toughness of the CF/EP laminates. The results showed that the addition of up to 3.0 wt.% CB in the epoxy matrix, with the assistance of CC, noticeably improved the electrical conductivity of the epoxy and the CF/EP laminates, with mechanical performance also enhanced to a certain extent.     

Effects of fibre/matrix adhesion on carbon-fibre-reinforced metal laminates—II. impact behaviour

Quasi-static, low-hanging and high-velocity impact tests have been conducted in order to study the effect of fibre/matrix adhesion on the impact properties of fibre-reinforced metal laminates. Differences in fibre/matrix adhesion were achieved by using treated or untreated carbon fibres in an epoxy resin system. Chemical removal of the aluminium layers and a sectioning technique were applied to examine and characterize the impact damage in the laminates. The results show that the laminates with the weaker fibre/matrix adhesion exhibit larger damage zones, although the back face crack length and permanent indentation after impact are smaller for a given impact energy. Residual tensile strength after impact is also higher for the untreated fibre laminates due to increased fibre/matrix splitting in the composite layer.     

Interlaminar fracture of CF/EP composite containing a dual-component microencapsulated self-healant

We present an experimental study of the self-healing ability of carbon fibre/epoxy (CF/EP) composite laminates with microencapsulated epoxy and its hardener (mercaptan) as a healing agent. Epoxy- and hardener-loaded microcapsules (average size large: 123 μm; small: 65 μm) were prepared by in situ polymerisation in an oil-in-water emulsion and were dry-dispersed at the ratio 1:1 on the surface of unidirectional carbon fabric layer. The CF/EP laminates were fabricated using a vacuum-assisted resin infusion (VARI) process. Width-tapered double cantilever beam (WTDCB) specimens were used to measure mode-I interlaminar fracture toughness of the CF/EP composites with a pre-crack in the centre plane where the microcapsules were placed. Incorporation of the dual-component healant stored in the fragile microcapsules provided the laminates with healing capability on delamination damage by recovering as much as 80% of its fracture toughness. It was also observed that the recovery of fracture toughness was directly correlated with the amount of healant covering the fracture plane, with the highest healing efficiency obtained for the laminate with large capsules.     

Effect of resin system on the mechanical properties and water absorption of kenaf fibre reinforced laminates

The objective of this study is to compare the mechanical and water absorption properties of kenaf (Hibiscus cannabinus L.) fibre reinforced laminates made of three different resin systems. The use of different resin systems is considered so that potentially complex and expensive fibre treatments are avoided. The resin systems used include a polyester, a vinyl ester and an epoxy. Laminates of 15%, 22.5% and 30% fibre volume fraction were manufactured by resin transfer moulding. The laminates were tested for strength and modulus under tensile and flexural loading. Additionally, tests were carried out on laminates to determine the impact energy, impact strength and water absorption. The results revealed that properties were affected in markedly different ways by the resin system and the fibre volume fraction. Polyester laminates showed good modulus and impact properties, epoxy laminates displayed good strength values and vinyl ester laminates exhibited good water absorption characteristics. Scanning electron microscope studies show that epoxy laminates fail by fibre fracture, polyester laminates by fibre pull-out and vinyl ester laminates by a combination of the two. A comparison between kenaf and glass laminates revealed that the specific tensile and flexural moduli of both laminates are comparable at the volume fraction of 15%. However, glass laminates have much better specific properties than the kenaf laminates at high fibre volume fractions for all three resins used.     

On the influence of weave structure on pin-loaded strength of orthogonal 3D composites

Orthogonal three-dimensional (3D) carbon fibre fabrics with different weave structures were obtained by varying the yarn spacing and number of carbon filaments per tow in the x-, y- and z-directions during weaving. These weave structures were impregnated with epoxy resin to produce orthogonal 3D carbon/epoxy composites. In addition, one-dimensional (0° and 90° unidirectional) and two-dimensional (cross-ply and plain fabric) laminates were prepared from the same carbon fibres and epoxy resin. Single-hole pin-loaded specimens of each material were tested in tension, and the influences of reinforcement type, weave structure, specimen width-to-hole diameter ratio and edge distance-to-hole diameter ratio evaluated. Various modes of failure were observed in the specimens. The effect of in-plane and out-of-plane fibres on the pin-loaded strength of orthogonal 3D composites is discussed.     

静电植绒法处理多壁碳纳米管改性玻纤织物/环氧树脂复合材料的制备及力学性能

为提高玻纤增强环氧树脂复合材料的力学性能,采用静电植绒法将多壁碳纳米管(MWCNTs)附着在玻纤织物表面,得到改性的玻纤织物。利用一种低黏度的环氧树脂和所制得的改性织物,采用真空辅助成型工艺(VARI)制备了MWCNTs改性格玻纤织物/环氧树脂复合材料层合板,表征了层合板的力学性能。对进行力学实验后的MWCNTs改性玻纤织物/环氧树脂复合材料试样断口进行了SEM和OPM观察。结果显示:与未添加MWCNTs的玻纤织物/环氧树脂复合材料层合板相比,添加了MWCNTs的层合板的拉伸强度降低了10.24%,弯曲强度降低了13.90%,压缩强度降低了17.33%,拉伸模量和弯曲模量分别提高了19.38%和16.04%,压缩模量提高了13%;MWCNTs与玻纤织物之间的结合较弱,在拉伸作用下,存在明显的脱粘和分层;将改性玻纤织物在200℃下热压处理2h后,制备的MWCNTs改性玻纤织物/环氧树脂复合材料层合板的力学性能均有所提高,热压处理后树脂与玻纤织物之间的界面结合得到改善。     

Mechanical behaviour of graphene and carbon fibre reinforced epoxy based hybrid nanocomposites for orthotic callipers

ABSTRACT

The current analysis examines the efficiency of a composite with polymer matrix reinforced with carbon fibre and graphene at the micro and nano level respectively as an alternative material for aluminium components of Orthotic callipers. An attempt has been made to use both the carbon fibre and graphene as hybrid reinforcement with the matrix as epoxy resin. The addition of graphene and carbon fibre was 2% and 10% respectively by weight of epoxy. Dispersion of graphene was carried out using an ultrasonic sonicator and carbon fibres were a reinforced using hand lay-up technique. The total fabrication was carried out under vacuum to ensure void-free test samples. The samples were tested under tension and 3 Point Bending condition to estimate the Tensile and Flexural properties, under permissible load and deflection criteria. The results found were then compared with presently used material for orthotic callipers extensively used by amputees suffering from the locomotive, gait issues, and polio-affected survivors. The proposed composite showed higher strength, lower deformation and higher stiffness with a lower weight-to-volume ratio as compared to presently used material, i.e. aluminium.     

Predicting the compressive engineering performance of carbon fibre-reinforced plastics

This paper examines the compressive strength data of a recent experimental study [Smith FC. The effect of constituents’ properties on the mechanical performance of fibre-reinforced plastics. PhD thesis. Centre for Composite Materials, Imperial College, April 1998] concerned with the evaluation of a range of engineering properties of continuous carbon fibre/epoxy composites subjected to static tensile and compressive loading. A plastic fibre kinking analysis [Budiansky B. Micromechanics. Comput Struct 1983;16(1):3–12] and a linear softening cohesive zone model (CZM) [Soutis C. Compressive failure of notched carbon fibre–epoxy panels. PhD thesis. Cambridge University Engineering Department, UK, 1989; Soutis C, Fleck NA, Smith PA. Failure prediction technique for compression loaded carbon fibre–epoxy laminates with an open hole. J Comp Mat 1991;25(5):1476–1498] are used for the prediction of the unnotched and open hole compressive strength (OHC) of unidirectional and multidirectional laminates made of six different commercially available CFRP prepregs. Damage introduced by drop-weight (low-velocity) impact is modelled as an equivalent open hole and the cohesive zone model [Soutis C. Compressive failure of notched carbon fibre–epoxy panels. PhD thesis. Cambridge University Engineering Department, UK, 1989; Soutis C, Fleck NA, Smith PA. Failure prediction technique for compression loaded carbon fibre–epoxy laminates with an open hole. J Comp Mat 1991;25(5):1476–1498] is applied to estimate compression-after-impact (CAI) strength. The unnotched strength is accurately predicted from the knowledge of initial fibre misalignment and the shear yield stress of the composite, while the difference between the theoretical and experimental OHC and CAI strength results in most cases is less than 10%.     

A self-healing carbon fibre reinforced polymer for aerospace applications

Self-healing is receiving increasing interest worldwide as a technology to autonomously address the effects of damage in composite materials. This paper describes the results of four point bend flexural testing (ASTM-D6272-02) of T300/914 carbon fibre reinforced epoxy with resin filled embedded hollow glass fibres (HGF) which provided a self-healing functionality. The study investigated the effect of the embedded HGF on the host CFRP mechanical properties and also the healing efficiency of the laminates after they were subjected to quasi-static impact. Specimens were tested in the undamaged, damaged and healed conditions using a commercial two-part epoxy healing agent (Cytec Cycom 823). Microscopic characterisation of the embedded HGF was also undertaken to characterise the effect on the host laminate fibre architecture.     

Improving the through-thickness thermal and electrical conductivity of carbon fibre/epoxy laminates by exploiting synergy between graphene and silver nano-inclusions

Fibre-reinforced polymer composites typically feature low functional (e.g., electric and thermal conductivity) and structural (e.g. mechanical strength and fracture toughness) properties in the laminate’s thickness direction. In the event of lightning strikes, overheating, and impact by foreign objects, composite laminates may suffer wide spread structural damage. This research explores the synergistic physical interaction between two-dimensional nanostructured (graphene nano-platelets) and, zero- or one-dimensional conductive fillers (silver nanoparticles or silver nanowires, respectively) when both are dispersed in fibre–polymer laminates. The results reveal a synergistic improvement in the through-thickness thermal conductivity that is more than the additive improvements by each constituent. Specifically, the simultaneous inclusion of graphene nano-platelets and silver nanoparticles/nanowires at a combined loading of 1 vol% resulted in approximately 40% enhancement in the through-thickness thermal conductivity while the inclusion of graphene nano-platelets alone at the same loading resulted only in 9% improvement. Similarly, the through-thickness electrical conductivity of carbon fibre/epoxy laminates incorporating graphene nano-platelets together with silver nanoparticles/nanowires was notably higher (⩾70%) than can be achieved by graphene nano-platelets alone (∼55%). These results demonstrate that the presence of nano-reinforcements exhibiting varied phonon transport and electron transfer pathways, and geometric aspect ratios promote synergistic physical interactions. Small improvements were found in the mechanical properties, including tensile, flexural or compressive properties of the carbon fibre-reinforced laminates, due to the relatively low concentrations of the nano-fillers.     

Effects of fibre/matrix adhesion on carbon-fibre-reinforced metal laminates—I.: Residual strength

The role of interfacial adhesion between fibre and matrix on the residual strength behaviour of carbon-fibre-reinforced metal laminates (FRMLs) has been investigated. Differences in fibre/matrix adhesion were achieved by using treated and untreated carbon fibres in an epoxy resin system. Mechanical characterisation tests were conducted on bulk composite specimens to determine various properties such as interlaminar shear strength (ILSS) and transverse tension strength which clearly illustrate the difference in fibre/matrix interfacial adhesion. Scanning electron microscopy confirmed the difference in fracture surfaces, the untreated fibre composites showing interfacial failure while the treated fibre composites showed matrix failure. No clear differences were found for the mechanical properties such as tensile strength and Young's modulus of the FRMLs despite the differences in the bulk composite properties. A reduction of 7·5% in the apparent value of the ILSS was identified for the untreated fibre laminates by both three-point and five-point bend tests. Residual strength and blunt notch tests showed remarkable increases in strength for the untreated fibre specimens over the treated ones. Increases of up to 20% and 14% were found for specimens with a circular hole and saw cut, respectively. The increase in strength is attributed to the promotion of fibre/matrix splitting and large delamination zones in the untreated fibre specimens owing to the weak fibre/matrix interface.     

分散方法对低含量碳纳米管玻纤/环氧层板性能的影响

采用超声波振荡与超声波破碎两种分散方法制备了低含量碳纳米管(CNTs)增强的环氧树脂, 研究了CNTs对树脂流变特性、 固化特性和力学性能的影响。进一步采用该树脂体系通过真空灌注工艺(VARIM)制备了CNTs含量为0.01%的CNTs-玻璃纤维/环氧树脂复合材料层板, 研究了两种分散方式下CNTs对复合材料层板力学性能的影响和CNTs的增强机制。结果表明: 超声波破碎分散使CNTs长度变短, 分散性更好, 与超声波振荡分散方式相比, CNTs对树脂增黏效果和树脂固化反应的影响更明显。采用双真空灌注工艺, 两种超声波分散方式下CNTs均提高了复合材料的弯曲性能、 层间剪切性能和树脂与纤维的粘结强度, 而单真空灌注工艺下CNTs的增强效果不明显, 说明受纤维过滤作用的影响, 选择合适的灌注工艺和CNTs分散方式, 低含量CNTs可实现对灌注工艺复合材料层板的增强。     

快速固化环氧树脂及其碳纤维/环氧复合材料性能

采用双酚A型环氧树脂（DGEBA）、改性咪唑（MIM）及改性脂肪胺（MAA）研制快速固化树脂体系。分别利用DSC和流变仪测试了树脂体系的固化特性与流变行为,优选了树脂配方。采用真空辅助树脂灌注工艺（VARIM）制备了快速成型的碳纤维/环氧复合材料层板,考察了层板的成型质量和力学性能,并与常规固化的层板性能进行了对比。结果表明：采用优选的树脂配方,120 ℃下树脂在5 min内固化度达95%,碳纤维/环氧复合材料层板成型固化时间可控制在13 min以内,固化度达95%以上,并且没有明显缺陷;与常规固化相比（固化时间大于2 h）,快速固化碳纤维/环氧复合材料层板的弯曲性能和耐热性能降低幅度较小。     

PEK-C膜层间增韧碳纤维/环氧树脂复合材料的力学性能

为探究热塑性酚酞基聚醚酮（Polyaryletherketone with Cardo,PEK-C）树脂薄膜及膜厚对层间增韧碳纤维/环氧树脂复合材料力学性能的影响,利用浸渍提拉法制备了三种不同厚度（分别约为1 μm、10 μm、30 μm）的PEK-C膜,通过热压成型制备了层间增韧碳纤维/环氧树脂复合材料层合板,对其进行了Ⅰ型层间断裂韧性、冲击后压缩强度、层间剪切及弯曲性能测试,并利用SEM观察微观形貌及AFM扫描微观相图。结果表明:不同PEK-C膜厚增韧碳纤维/环氧树脂复合材料的Ⅰ型层间断裂韧性、冲击后压缩强度及层间剪切强度有不同程度提高,Ⅰ型层间断裂韧性及层间剪切强度以膜厚为10 μm最佳,分别增大了157.17%和17.57%,冲击后压缩强度以膜厚为30 μm最佳,达到了186.67 MPa,这是由于PEK-C与环氧树脂在热压固化过程中形成了双相结构,改善了材料韧性;但弯曲性能持续下降,强度及模量由未增韧的1 551 MPa、106 GPa分别降至30 μm时的965 MPa、79 GPa,这是由于PEK-C树脂扩散进入环氧树脂中,降低了纤维体积分数及材料刚度。      

Evaluation on the thermal and mechanical properties of HNT-toughened epoxy/carbon fibre composites

Halloysite nanotubes (HNT) were effectively incorporated into epoxy resin and used for infusion of carbon fibre textiles, resulting in epoxy/halloysite nanotube/carbon fibre (EP/HNT/CF) multi-scale composites. The distribution of nanotubes in the composites was examined by SEM. The thermomechanical properties of the composites were characterized by dynamic mechanical analyser (DMA). A 25% enhancement was recorded for the storage modulus of EP/HNT/CF composite in the glassy state. Moreover, the T_g of the laminates increased with the addition of HNT, and the values were even higher than the T_g of their matrix. Additionally, the Izod impact strength of the composites has been improved. These results indicate a synergistic effect between HNT and carbon fibres.     

Bioinspired self-healing of advanced composite structures using hollow glass fibres

Self-healing is receiving an increasing amount of worldwide interest as a method to autonomously address damage in materials. The incorporation of a self-healing capability within fibre-reinforced polymers has been investigated by a number of workers previously. The use of functional repair components stored inside hollow glass fibres (HGF) is one such bioinspired approach being considered. This paper considers the placement of self-healing HGF plies within both glass fibre/epoxy and carbon fibre/epoxy laminates to mitigate damage occurrence and restore mechanical strength. The study investigates the effect of embedded HGF on the host laminates mechanical properties and also the healing efficiency of the laminates after they were subjected to quasi-static impact damage. The results of flexural testing have shown that a significant fraction of flexural strength can be restored by the self-repairing effect of a healing resin stored within hollow fibres.     

Determination of stiffness properties of braided composites for the design of a hip prosthesis

This paper describes an experimental procedure used to determine the stiffness properties of two different composites made of braided glass and hybrid carbon–glass fibre reinforced epoxy resin. Tubular specimens manufactured by reinforcing an epoxy resin system with commercial braided preforms were used to determine the elastic constants. All specimens were manufactured using compression moulding technique assisted with internal pressure. The stiffness properties were determined from axial and circumferential strains recorded from strain gauges using internal water pressure tests. Identical types of composite laminates were used to manufacture two prototypes of a composite femoral prosthesis with controlled stiffness.     

RTM processing and electrical performance of carbon nanotube modified epoxy/fibre composites

This investigation focuses on nanoparticle filtration in the processing of multiscale carbon and glass fibre composites via resin transfer moulding. Surface modified and unmodified carbon nanotubes (CNTs) were incorporated into a commercial epoxy resin. The dispersion quality was evaluated using electrical measurements of the liquid suspensions. The manufacturing process was adapted to the challenges posed by the modified rheological behaviour of the CNT loaded resin. Nanoparticle filtration was observed; with some of the unmodified systems following so called ‘cake filtration’ behaviour. This resulted in nonlinear flow behaviour that deviated from the ideal response observed in RTM filling in conventional composites. The electrical conductivity of relatively high fibre volume fraction multiscale carbon and glass laminates increased by less than an order of magnitude with the addition of the nanotubes.