共查询到20条相似文献,搜索用时 62 毫秒
1.
用循环伏安法研究了石墨电极在PC系电解液中的电化学行为。溶剂为PC时,PC在石墨电极上大量分解并同Li 一起嵌入石墨层中,导致石墨完全剥落,通过调整溶剂的组成和配比,可抑制PC嵌入石墨电极。对石墨电极在PC系电解液中的首次充放电研究表明:随着电解液中DMC含量的增加,电池首次充放电的不可逆容量减小。对含PC系电解液的锂离子电池循环性能的研究表明:电池的初始容量和循环稳定性随着电解液中DMC含量的增加而增加,电解液组成为1 mol/L LiPF6/EC PC DMC(1∶1∶4)时,电池初始放电容量为784.2 mAh,经50次循环后,容量保持率达97.0%。 相似文献
2.
3.
4.
电解液添加剂对锂离子蓄电池循环性能的影响 总被引:8,自引:3,他引:5
为了改善锂离子蓄电池的循环性能 ,在EC/DEC/1.0mol/LLiClO4 电解液体系中加入微量添加剂苯甲醚。以Li金属和改性石墨为电极材料 ,循环性能测试结果表明 ,苯甲醚的加入 ,使电池的可逆比容量和充放电效率均得到提高 ,且可逆比容量的衰减速度减慢。用FTIR对首次离子嵌入过程结束后的石墨电极表面SEI(SolidElectrolyteInterface)进行组成分析 ,发现加入苯甲醚后 ,电极表面SEI中的RCO3Li含量明显减少 ,但Li2 CO3 基本不变 ,并发现有新的产物CH3OLi生成。根据以上分析结果 ,提出了苯甲醚对锂离子电池循环性能的影响机理 :在Li+嵌入石墨电极的初次过程中 ,苯甲醚和EC、DEC的还原分解产物RCO3Li发生基团交换反应 ,生成CH3OLi ,该产物能有效提高石墨电极表面SEI的稳定性 ,减少锂离子嵌入石墨过程中引起的溶剂分子共嵌入 ,从而改善电池的循环性能。 相似文献
5.
6.
运用循环伏安法(CV)和电化学阻抗谱(EIS)研究了1mol/LLiPF6/[EC(碳酸乙烯酯)+DEC(碳酸二乙酯)+DMC(碳酸二甲酯)(体积比为1∶1∶1)]中添加Li2CO3对锂离子电池负极石墨界面特性的影响。研究结果表明添加剂Li2CO3可以有效地减弱电解液中EC在0.75V的还原分解以及抑制在0.6V烷基碳酸锂的形成,保持电解液的稳定和降低锂离子的损耗,提高锂离子电池的循环稳定性;在3V开路电位时电解液中添加的Li2CO3对接触阻抗及锂离子在石墨电极中的扩散无影响;电解液中添加Li2CO3可以使石墨负极表面的SEI膜仅在1.00~0.80V内快速形成而在0.6~0.8V内基本不变;EIS拟合表明电解液中添加Li2CO3可以同时降低SEI膜电阻和电荷传递电阻。 相似文献
7.
8.
LiBOB电解液在石墨负极上的成膜性能 总被引:4,自引:3,他引:1
利用循环伏安和充放电循环测试,对锂离子电池负极材料[人造石墨E-SLX50和中间相碳微球(MCMB)]与PC作溶剂的LiBOB电解液的相容性进行了研究。石墨表面生成的SEI膜,不仅与电解液的组成和浓度有关,还与石墨的种类及结构有关。在1.0 mol/L LiBOB/PC电解液中,两种材料均能生成稳定的SEI膜;在0.5 mol/L LiBOB/PC电解液中,MCMB可生成稳定的SEI膜,而E-SLX50只有在电解液含EC共溶剂时,通过EC和LiBOB的共同作用,才能生成稳定的SEI膜。 相似文献
9.
10.
11.
12.
电站锅炉停用保护剂多采用十八胺和表面活性胺。对这2种停用保护剂进行了应用效果对比研究,即对湿冷机组、空冷机组采用十八胺或表面活性胺、有无凝结水精处理系统等6台机组停机和启动过程中给水、主蒸汽和凝结水的氢电导率变化情况进行分析。研究结果表明:在停机过程和启动过程,2种保护剂均会在水汽系统中发生部分分解,导致水汽系统的氢电导率显著升高;表面活性胺和十八胺比较,使用前者,机组启停机过程可保持凝结水精处理系统正常投运,因而可使水汽质量迅速达标,对机组安全运行有利,因此推荐采用表面活性胺作为锅炉停用保护剂。 相似文献
13.
特高压线路工频参数测试干扰分析是选择适合工频参数测试方法及测试结果分析的重要基础。测试了1 000 kV皖南-浙北特高压线路正序和零序参数测试期间的干扰电压信号,分析了其频谱特征;在此基础上,通过与正序参数仿真计算值的对比分析了正序参数实际测试偏差。结果表明:皖南-浙北特高压同塔双回线路工频参数测试期间,干扰电压存在“三相不平衡性及时变性”的特点;工频法和异频法2种不同方法得到的线路参数测试结果存在一定差异;干扰电压“时变”时,线路工频参数测试宜采用异频法。 相似文献
14.
15.
《国外电子测量技术》2014,(10)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world’s premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
16.
17.
《国外电子测量技术》2014,(9)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world's premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
18.
Cuba’s electric sector is approaching an inflection point. Although the country has historically relied upon non-commercial barter agreements for imported oil to meet its electric demand, a combination of factors including reducing imports, increasing demand, and ambitious climate change goals suggest new pathways forward may be warranted. The way Cuba responds to near- and long-term challenges will help set the stage for its energy future. This article describes Cuba's electric sector and provides a set of key recommendations to consider going forward. 相似文献
19.
S. Y. Wu B. N. Tran F. Y. Davis C. L. Trent D. L. Edberg W. A. Geideman 《Integrated ferroelectrics》2013,141(3):281-291
Abstract Smart materials of lead-zirconate-titanate (PZT) piezoelectric ceramics have attracted attention in recent years for active vibration control, acoustic noise suppression, health monitoring and damage assessment. We at McDonnell Douglas Aerospace have been studying these ceramics for use as sensors and actuators in various space and aircraft structures. In this paper, we will report results of a recent study on active vibration control using monomorph PZT actuators. The experiments were performed on thin aluminum cantilever beams. Collocated and non-collocated sensors and actuators were employed. Two control techniques: the classical velocity feedback and adaptive feedback controls, were investigated. We have obtained significant damping and broadband vibration attenuation of greater than 30 dB using the classical control with the single-input single-output feedback approach. A 24 dB reduction has also been achieved using the adaptive control with the multiple-input single-output approach. Detailed experimental methods and results will be described. 相似文献