On the friction and wear behavior of PTFE composite filled with rare earths treated carbon fibers under oil-lubricated condition

Carbon fibers (CF) were surface treated with air-oxidation, air-oxidation followed by rare earths (RE) treatment and RE treatment, respectively. The friction and wear properties of the polytetrafluoroethylene (PTFE) composites filled with differently surface treated carbon fibers, sliding against GCr15 steel under oil lubrication, were investigated on a reciprocating ball-on-disk UMT-2MT tribometer. The worn surfaces of the PTFE composites were examined using a scanning electron microscopy (SEM). Experimental results revealed that surface treatment of carbon fibers reduced the wear of CF-reinforced PTFE composites. Among all the treatments to carbon fibers, RE treatment was the most effective and lowest friction and wear rate of CF-reinforced PTFE composite was exhibited, owing to the effective improvement of the interfacial adhesion between the carbon fibers and PTFE matrix.     

Effect of plasma treatment of Kevlar fabric on the tribological behavior of Kevlar fabric/phenolic composites

Pure and plasma-treated Kevlar fabrics were used to prepare Kevlar fabric/phenolic composites by consecutive dipping of the fabric in phenolic adhesive resin. The friction and wear performance of the resulting composites has been evaluated in a pin-on-disk wear tester at various dry-sliding conditions. The surface changes occurring on Kevlar fibers treated with air-plasma were analyzed by using X-ray photoelectron spectroscope (XPS), Fourier transform infrared spectroscope (FT-IR) and scanning electron microscope (SEM). Moreover, the impact of air-plasma treatment time and power on the friction and wear behavior of Kevlar fabric/phenolic composites composed of the air-plasma-treated Kevlar fabrics was systematically studied. It was found that plasma treatment can significantly improve the tribological performance of the prepared Kevlar fabric/phenolic composites; the best performance was after a plasma treatment at 50 W for 15 min. The plasma treatment generates oxygenic and nitrogenous groups on the surface of the fabric, coupled with an increase of the surface roughness, strengthening the bond between the Kevlar fabric and phenolic adhesive resin and hence improving the tribological properties of the Kevlar fabric/phenolic composites.     

Study on the tribological behavior of hybrid PTFE/cotton fabric composites filled with Sb2O3 and melamine cyanurate

The tribological behavior of the hybrid PTFE/cotton fabric composites filled with microsize Sb₂O₃ and melamine cyanurate (MCA) was investigated. It was found that the wear rate of the hybrid PTFE/cotton fabric composites decreased when Sb₂O₃ was used as the filler but increased with MCA filler. It was also observed that hybrid fillers (consists of Sb₂O₃ and MCA) had a wear reduction effect on the hybrid PTFE/cotton fabric composites at lower loads but increased the wear rate at higher loads. The wear behavior of the composites was explained in terms of the topography of worn surfaces and transfer film formed on the counterpart pin.     

Film-forming mechanisms for self-lubricating radial spherical plain bearings with hybrid PTFE/aramid fabric liners modified by ultrasonic

PTFE/aramid woven fabric liners were modified by ultrasonic. With self-made wear tester, tribological properties of the self-lubricating radial spherical plain bearings with modified and unmodified liners over swivel times were investigated. With scanning electron microscope and energy disperse spectroscopy, the film-forming mechanisms were analyzed. Results show: ultrasonic modification can improve tribological performances of the liners. Through ultrasonic modification, continuous and stable PTFE transfer films which had better wear resistance formed in a shorter time. Bearings with modified liners occurred slight adhesive wear, while the bearings with unmodified liners occurred serious adhesive wear and abrasive wear during the test process.     

Influence of weave structures on the tribological properties of hybrid Kevlar/PTFE fabric composites

The existing research of the woven fabric self-lubricating liner mainly focus on the tribological performance improvements and the service life raised by changing different fiber type combinations, adding additive modification, and performing fiber surface modification. As fabric composites, the weave structures play an important role in the mechanical and tribological performances of the liners. However, hardly any literature is available on the friction and wear behavior of such composites with different weave structures. In this paper, three weave structures (plain, twill 1/3 and satin 8/5) of hybrid Kevlar/PTFE fabric composites are selected and pin-on-flat linear reciprocating wear studies are done on a CETR tester under different pressures and different frequencies. The relationship between the tensile strength and the wear performance are studied. The morphologies of the worn surfaces under the typical test conditions are analyzed by means of scanning electron microscopy (SEM). The analysis results show that at 10 MPa, satin 8/5 performs the best in friction-reduction and antiwear performance, and plain is the worst. At 30 MPa, however, the antiwear performance is reversed and satin 8/5 does not even complete the 2 h wear test at 16 Hz. There is no clear evidence proving that the tensile strength has an influence on the wear performance. So the different tribological performance of the three weave structures of fabric composites may be attributed to the different PTFE proportions in the fabric surface and the different wear mechanisms. The fabric composites are divided into three regions: the lubrication region, the reinforced region and the bonding region. The major mechanisms are fatigue wear and the shear effects of the friction force in the lubrication region. In the reinforced region fiber-matrix de-bonding and fiber breakage are involved. The proposed research proposes a regional wear model and further indicates the wear process and the wear mechanism of fabric composites.     

The friction and wear of electroless Ni–P matrix with PTFE and/or SiC particles composite

In this paper, the friction behaviour and wear mechanism of electroless Ni–P matrix with PTFE and/or SiC particles composite coating are investigated by virtue of ring-on-disk wear machine at a high load of 150 N. The worn surface, wear debris and the composition changes after wear were characterized using scanning electron microscopy (SEM) and energy-dispersive analysis of X-ray (EDAX). By comparison with Ni–P and Ni–P–SiC coatings, the results indicated that the combination of a PTFE-rich mechanical mixed layer (PRMML) formed on the worn surface and hard SiC were responsible for the good tribological properties of the hybrid Ni–P–PTFE–SiC composites at high load. After heat treatment at 400 °C for 1 h, the wear rate of Ni–P matrix composites decreased with corresponding increase in microhardness. During sliding, an obvious decrease in the temperature rise with PTFE addition was attributed to the good anti-friction of PTFE.     

A Study on the Sliding Wear of Hybrid PTFE/Kevlar Fabric/Phenolic Composites Filled with Nanoparticles of TiO2 and SiO2

TiO₂ and SiO₂ nanoparticles were introduced into hybrid polytetrafluoroethylene (PTFE)/Kevlar fabric/phenolic composites. The results showed the incorporation of TiO₂ nanoparticles can reduce the wear rate of the fabric/phenolic composite at elevated temperatures, although the wear of hybrid PTFE/Kevlar fabric/phenolic composite did not change much when TiO₂ or SiO₂ nanoparticles were used as filler. The wear behavior was explained in terms of morphology of transfer films and worn surfaces. There was a good correlation between the morphology of transfer film and wear results.     

Friction and wear of friction materials containing two different phenolic resins reinforced with aramid pulp

Friction and wear characteristics of automotive friction materials containing two different phenolic resins (a straight novolac resin and a modified novolac resin) were investigated using a pad-on-disk type friction tester. Six different friction materials with different relative amounts of the phenolic resins and aramid pulp were manufactured and tested. Two different test modes were employed to examine the friction characteristics concerning accumulated thermal history (a constant initial temperature test: test mode I) and friction heat (a constant interval test: test mode II). Friction characteristics such as friction stability and wear resistance were changed significantly according to the type of phenolic resins and to the relative amount of the resin and aramid pulp. Friction materials with the modified novolac resin showed better friction stability than those with the unmodified novolac resin. In particular, the friction materials that were reinforced with 10 vol.% of aramid pulp showed substantial improvement on friction stability regardless of the resin type. However, the friction materials with the modified resin showed significant reduction in wear resistance.     

Friction and wear properties of metal powder filled PTFE composites under oil lubricated conditions

Four kinds of polytetrafluoroethylene (PTFE)-based composite, pure PTFE, PTFE+30vol.%Cu, PTFE+30vol.%Pb and PTFE+30vol.%Ni composite, were prepared. The friction and wear properties of these metal powder filled PTFE composites sliding against GCr15 bearing steel under both dry and lubricated conditions were studied using an MHK-500 ring-block wear tester. The worn surfaces of the PTFE composites and the transfer films formed on the surface of GCr15 bearing steel were examined using scanning electron microscopy (SEM) and optical microscopy respectively. Experimental results show that the friction and wear properties of the PTFE composites can be greatly improved by liquid paraffin lubrication. The wear of these PTFE composites can be decreased by at least 1 to 2 orders of magnitude compared with that under dry friction conditions, while the friction coefficients can be decreased by 1 order of magnitude, SEM and optical microscopy investigations of the rubbing surfaces show that metal fillers of Cu, Pb and Ni not only raise the load carrying capacity of the PTFE composites, but also promote transfer of the PTFE composites onto the counterfaces, so they greatly reduce the wear of the PTFE composites. However, the transfer of these PTFE composites onto the counterfaces can be greatly reduced by liquid paraffin lubrication, but transfer still takes place.     

纳米晶粉末制备复合材料的摩擦磨损性能

本文研究了用机械合金化方法制备出Ｓｉ３Ｎ４／Ｆｅ基纳米晶复合粉末，用常规粉末冶金工艺烧结出试样，测试了复合材料的常温摩擦磨损性能，并对其显微组织进行了分析，认为纳米晶的界面确实机改善Ｓｉ３Ｎ４与Ｆｅ的结合强度。     

On dry sliding friction and wear behavior of PPESK filled with PTFE and graphite

Novel poly(phthalazinone ether sulfone ketone) (PPESK) resins have become of great interest in applications such as bearing and slider materials. In this paper, dry sliding wear of polytetrafluoroethylene (PTFE) and graphite-filled PPESK composites against polished steel counterparts were investigated on a block-on-ring apparatus at the same sliding velocities and different loads. The results indicated that the addition of 5–25 wt% PTFE and 5–30 wt% graphite contribute to an obvious improvement of tribological performance of PPESK at room temperature. Worn surfaces were investigated using a scanning electron microscope (SEM). As a result, the friction coefficient and wear rate of the PPESK composites decreased gradually with addition of fillers. A moderately low friction coefficient and specific wear rate were reached when the filler contents were above 20 wt%. The mechanical properties of PPESK composites were also investigated. The tensile and impact strength of PPESK composites decrease slightly as the addition of fillers contents were below 15 wt%.     

Friction and dry sliding wear behavior of carbon and glass fabric reinforced vinyl ester composites

Friction and dry sliding wear behavior of glass and carbon fabric reinforced vinyl ester composites have been presented. The results show that the coefficient of friction and wear rate increased with increase in load/sliding velocity and depends on type of fabric reinforcement and temperature at the interphase. The excellent tribological characteristics were obtained with carbon fiber in vinyl ester. It is believed that a thin film formed on counterface was seems to be effective in improving the tribological characteristics. The worn surfaces examined through SEM, showed higher levels of broken glass fiber in vinyl ester compared to carbon-vinyl ester composites.     

Friction and wear behavior of human teeth under various wear conditions

Previous reports have described the differences in the friction and wear behavior between different zones of human teeth. The objective of this research was to study the friction and wear behavior of human teeth under different wear conditions to extend the understanding of the tooth wear process, as well as to provide a more rational explanation for wear mechanism of teeth. Two typical wear tests, namely two- and three-body wear, were conducted on human tooth enamel using a reciprocating apparatus. The effect of food particles was of particular interest. Three loads, 10, 20 and 40 N, were used. Wear was assessed by sample wear volume. The results show that human tooth enamel exhibits lower friction and smaller wear volume under three-body wear conditions than under two-body wear conditions. Under three-body wear conditions, although increasing normal load results in a progressive increase in the wear volume of enamel, the increasing rate is lower at high load than that under two-body wear conditions. Further analysis of wear surfaces indicates that human tooth enamel experiences different wear mechanisms under different wear conditions.     

Friction and wear studies of an internally lubricated polyetherimide composite

Polyetherimide (PEI) is one of the latest generic high-performance engineering thermoplastics. PEI (developed by General Electric (USA) under the trade name ULTEM) is an amber and amorphous polymer with a heat distortion temperature between those of polyarylate resin and thermally stable crystalline polymers such as polyether-ether ketone (PEEK) and polyamideimide (PAI). It has excellent thermal, mechanical and electrical properties along with easy processability. In the work reported here, a wear-resistant formulated composite supplied by GEC (ULTEM 4001) was selected for tribological investigations on a pin on disc machine under unlubricated conditions, against mild steel. Analysis of the composite revealed that this grade contained PTFE (13–15%), which is the most promising polymeric lubricant. A very low and stable frictional coefficient was observed against moderately finished surfaces. However, its specific wear resistance (⋍10⁻¹⁴ m³/Nm) was comparatively lower than that of fibre-reinforced thermoplastics. The wear mechanism was found to be significantly dominated by the presence of PTFE. The friction coefficient was in the range of 0.2 and reduced to a still lower value (0.1) as the apparent contactpressure increased. Scanning electron microscopy was used to investigate the underlying wear mechanism. Film transfer of PTFE was observed to be the principal factor responsible for reduced friction.     

Tribological behavior of spun Kevlar fabric composites filled with fluorinated compounds

The tribological behavior of the spun Kevlar fabric composites filled with polyfluo wax (PFW) and LaF₃ were evaluated using a pin-on-disc friction and wear tester under variable applied load and rotating speed. The worn surface and transfer film of the composites were then examined with SEM. The results indicated that the oxidation of PFW after curing and viscous flow characteristic of PFW in friction process were beneficial to the formation of the compact, uniform and smooth transfer film, corresponding to the excellent wear resistance of the composite filled with 15 wt% PFW. The corresponding wear mechanisms were also discussed.     

Friction and wear behavior of Ni-P coated Si3N4 reinforced Al6061 composites

Al6061 matrix composite reinforced with nickel coated silicon nitride particles were manufactured by liquid metallurgy route. Microstructure and tribological properties of both matrix alloy and developed composites have been evaluated. Dry sliding friction and wear tests were carried out using pin on disk type machine over a load range of 20-100 N and sliding velocities of range 0.31-1.57 m/s. Results revealed that, nickel coated silicon nitride particles are uniformly distributed through out the matrix alloy. Al6061-Ni-P-Si₃N₄ composite exhibited lower coefficient of friction and wear rate compared to matrix alloy. The coefficient of friction of both matrix alloy and developed composite decreased with increase in load up to 80 N. Beyond this, with further increase in the load, the coefficient of friction increased slightly. However, with increase in sliding velocity coefficient of friction of both matrix alloy and developed composite increases continuously. Wear rates of both matrix alloy and developed composites increased with increase in both load and sliding velocity. Worn surfaces and wear debris was examined using scanning electron microscopy (SEM) for possible wear mechanisms. Energy dispersive spectroscope (EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscope (XPS) techniques were used to identify the oxides formed on the worn surfaces and wear debris.     

Effects of filler crystal structure and shape on the tribological properties of PTFE composites

In this paper, effects of filler crystal structure and shape on the friction and wear properties of potassium titanate whisker (K₂Ti₄O₉ whisker, K₂Ti₆O₁₃ whisker), TiO₂ whisker and TiO₂ particle filled polytetrafluoroethylene (PTFE) composites under dry friction conditions were studied. Meanwhile the influence of filler content, sliding duration, test speed and load were also investigated. Experimental results show that the friction coefficients of various PTFE-based composites are weakly dependent on filler shape but they are more strongly dependent on filler crystal structure. However, for improving the anti-wear property of PTFE, filler crystal structure has less importance than filler shape in the wear-reducing action of PTFE-based composites, and whisker-like filler is better than particle-like filler.     

Sliding Wear of the Hybrid Kevlar/PTFE Fabric Reinforced Phenolic Composite Filled with Nano-titania

The Kevlar/polytetrafluroethylene(Kevlar/PTFE) fabric composite can be used as a self-lubricating liner of the self-lubricating bearing.Many types of nano-particles can improve the tribological performance of the polymer-based composite.Unfortunately,up to now,published work on the effect of nano-particles on the tribological performance of the fabric composite which can be used as a self-lubricating liner is quite scarce.Therefore,for the purpose of exploring a way to significantly improve the tribological performance of the fabric composite,the tribological performance of the Kevlar/PTFE fabric composite filled with nano-titania is evaluated by using the block-on-ring wear tester.The scanning electron microscopy is utilized to observe the morphologies of worn surfaces of the fabric composites and the counterparts.The tensile properties of the composites are evaluated on the universal material testing machine.The test results show that the addition of nano-titania at a proper mass fraction of the matrix resin improves the wear resistance and the tensile strength,decreases the friction coefficient,and makes the wear volume of the composite reach a relative steady state more quickly;plastic deformation and microcutting are important for the wear of the fabric composite;a lubricating layer is formed on the worn surface of the composite during sliding,and the lubricating layer is critical for the tribological performance of the composite;the formation and properties of the lubricating layer are influenced by the nano-titania particles.The proposed study on the effect of nano-titania on the tribological performance of the Kevlar/PTFE fabric composite,especially on the evolution of the worn surface of the composite,provides the basis for further understanding of the influence mechanism of the nano-particles on the tribological performance of the composite and explores a method of improving the tribological performance of the composite.     

Friction and wear of sintered metallic brake linings on a C/C-SiC composite brake disc

The friction and wear of sintered metallic brake linings on a C/C-SiC composite brake disc were studied. This paper reports on the friction and wear properties of sintered metallic (MMC) brake linings, which appear to combine well with a C/C-SiC brake disc. The friction characteristics were examined with a dynamometer on two different commercial motorcycle brake systems, differing in terms of the brake caliper and the dimensions of the disc. The influence of the components, such as graphite, and the abrasives in the metallic matrix on the formation of the friction layer was investigated using a scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDX). The friction layer formed on the pad's sliding surface by oxidation wear, which consisted mostly of iron and copper oxides, was confirmed. The friction properties of the sintered metallic brake pads were determined and related to the composition and structure of the brake lining. This investigation of the friction characteristics of a brake couple comprising (MMC) brake linings and a C/C-SiC composite disc will increase our understanding of this material, which works in a completely different way to classical brakes based on metallic discs.     

The influence of metal surface composition on the tribological properties of filled PTFE/steel couples

In this paper, the friction and wear behaviors of filled PTFE/steel couples are studied. The stationary specimen was made of filled PTFE. The rotating specimen, made of steels, underwent various treatments. The experimental results showed that the frictional coefficient and wear rate were low when the surface of the steel specimen contained nitrogen. The structure of the transfer film was examined by X-ray photoelectron spectroscopy (XPS). The transfer film containing nitrogen on the steel surface was thick. The authors consider that the hypothesis of the adhesion of the n–p–n structure may explain the characteristics of the different sliding couples in this paper and might be an important way to improve the friction and wear properties of the filled PTFE/metal sliding couples.