Sintering kinetics of α-Al2O3 powder

The sintering kinetics of α-Al₂O₃ powder are reviewed in this paper. The initial sintering of α-Al₂O₃ micropowder and α-Al₂O₃ nanopowder is all controlled by grain boundary diffusion. The sintering kinetics dominate up to a relative density of 0.77, where the coarsening kinetics dominate during further densification. Herring's scaling law can be used to predict the approximate sintering temperature of α-Al₂O₃ powder and demonstrates that if the particle size can be reduced to <20 nm, sintering below 1000°C may be possible. ©     

Indirect selective laser sintering of epoxy resin-Al2O3 ceramic powders combined with cold isostatic pressing

To fabricate Al₂O₃ ceramic components with complex shape, selective laser sintering (SLS) combined with cold isostatic pressing (CIP) process was used to consolidate Al₂O₃ powder with additive of epoxy resin E06 (ER06) and polyvinyl alcohol (PVA). The starting material preparation combined spray drying with mechanical mixing to formulate compound powder consisting of PVA (1.5 wt%), ER06 (8 wt%) and Al₂O₃ and provide a good fluidity for SLS. Experimental investigations were carried the shrinkage, relative density, bending strength of Al₂O₃-ER06 SLS specimens in order to optimize the laser sintering parameters. It was found that Al₂O₃-ER06 SLS specimens represented acceptable shrinkage, high density and bending strength when laser power, scanning speed, scanning space and layer thickness were, respectively, 21 W, 1600 mm/s, 100 μm and 150 μm. Following that, the SLS specimens were processed through CIP to eliminate the pores in green ceramics. Finally, the optimized SLS/CIP Al₂O₃ specimens were debinded, sintered to produce crack-free Al₂O₃ bodies. The final Al₂O₃ components achieved a relative high density of more than 92% after furnace sintering. The study shows a novel and promising approach to fabricate complex ceramic matrix and ceramic components via indirect SLS and CIP process.     

A simple and effective process for fabrication of Gd0.1Ce0.9O1.95 solid electrolyte ceramics

Ce_0.9Gd_0.1O_1.95 ceramics were prepared using a simple and effective process in this study. Without any prior calcination, the mixture of raw materials was pressed and sintered directly. The reaction of the raw materials occurred during the heating up period by passing the calcination stage in the conventional solid-state reaction method. More than 99.5% of theoretical density was obtained for Ce_0.9Gd_0.1O_1.95 sintering at 1500–1600 °C. Fine grains (<1 μm) formed in pellets sintered at 1450 °C. The homogeneity of grains increased with the sintering temperature. The grains grew to >4.5 μm in pellets sintered at 1600 °C. The reactive-sintering process is proved to be a simple and effective method in preparing Ce_0.9Gd_0.1O_1.95 ceramics for solid electrolyte application.     

Influence of low concentration of SO2 for selective reduction of NO by C3H8 in lean-exhaust conditions on the activity of Ag/Al2O3 catalyst

The effect of SO₂ for the selective reduction of NO by C₃H₈ on Ag/Al₂O₃ was investigated in the presence of excess oxygen and water vapor. The NO_x conversion decreased permanently even in the presence of a low concentration of SO₂ (0.5–10 ppm) at <773 K. The increase in SO₂ concentration resulted in a large decrease in NO_x conversion at 773 K. However, when the reaction temperature was more than 823 K, the activity of Ag/Al₂O₃ remained constant even in the presence of 10 ppm of SO₂. The sulfate species formed on the used Ag/Al₂O₃ were characterized by a temperature programmed desorption method. The sulfated species formed on silver should mainly decrease the deNO_x activity on the Ag/Al₂O₃. The sulfated Ag/Al₂O₃ was appreciably regenerated by thermal treatment in the deNO_x feed at 873 K. The moderate activity remains at 773 K in the presence of 1 ppm SO₂ for long time by the heat treatment at every 20 h intervals.     

Thermal shock resistance of in situ formed Si2N2O–Si3N4 composites by gelcasting

Thermal shock resistance of Si₂N₂O–Si₃N₄ composites was evaluated by water quenching and subsequent three-point bending tests of strength diminution. Si₂N₂O–Si₃N₄ composites which was prepared with in situ liquid pressureless sintering process using Yb₂O₃ and Al₂O₃ powders as sintering additives by gelcasting showed no macroscopic cracks and the critical temperature difference (ΔT_c) could be up to 1400 °C. A mass of pores existed in the sintered body and the irregular shaped fibers extended from the pores increased the thermal shock property.     

Sintering of aluminum nitride by using alumina crucible and MoSi2 heating element at temperatures of 1650 °C and 1700 °C

Aluminum nitride (AlN) ceramics, prepared with Y₂O₃ and CaO sintering additives, have been densified in an Al₂O₃ crucible at temperatures of up to 1650 °C and 1700 °C using a conventional MoSi₂ heating element furnace. The results of this study show that relative densities in excess of 99% of theoretical and a relatively high-thermal conductivity of 147 W m⁻¹ K⁻¹ have been achieved for feedstock materials prepared with combined addition of 1 wt.% Y₂O₃ and 1 wt.% CaO. All of the phases in sintered samples have been shown to be crystalline AlN and minor amount of secondary phases, were detected such as enriched Y- and Ca-aluminates by the XRD patterns, back-scattered imagery and microprobe analysis. The advantage of using the particular experimental system and sintering condition is considered to be amenable to lower production cost and enhance the feasibility of mass production. Critical temperature for AlN densification to obtain the highest density is about 1650 °C.     

Sintering of Al2O3-SiC composite from sol-gel method with MgO, TiO2 and Y2O3 addition

Al₂O₃-SiC composite ceramics were prepared by pressureless sintering with and without the addition of MgO, TiO₂ and Y₂O₃ as sintering aids. The effects of these compositional variables on final density and hardness were investigated. In the present article at first α-Al₂O₃ and β-SiC nano powders have been synthesized by sol-gel method separately by using AlCl₃, TEOS and saccharose as precursors. Pressureless sintering was carried out in nitrogen atmosphere at 1600 °C and 1630 °C. The addition of 5 vol.% SiC to Al₂O₃ hindered densification. In contrast, the addition of nano MgO and nano TiO₂ to Al₂O₃-5 vol.% SiC composites improved densification but Y₂O₃ did not have positive effect on sintering. Maximum density (97%) was achieved at 1630 °C. Vickers hardness was 17.7 GPa after sintering at 1630 °C. SEM revealed that the SiC particles were well distributed throughout the composite microstructures. The precursors and the resultant powders were characterized by XRD, STA and SEM.     

Rapid consolidation of nanocrystalline Al2O3 reinforced Ni–Fe composite from mechanically alloyed powders by high frequency induction heated sintering

Nano-powders of Ni–Fe and Al₂O₃ were made from NiO and FeAl powders by high-energy ball milling. Nanocrystalline 5Ni_0.6Fe_0.4–Al₂O₃ composite was consolidated by high frequency induction heated sintering (HFIHS) method within 2 min from mechanically alloyed powders of Al₂O₃ and Ni–Fe. The average grain size and mechanical properties of the composite were investigated.     

Pulsed electric current sintering of transparent Cr-doped Al2O3

Pulsed electric current sintering (PECS) was applied to obtain transparent ruby polycrystals. Al₂O₃-Cr₂O₃ powder mixture was prepared by drying an aqueous slurry consisting of Al₂O₃ and Cr(NO₃)₃ followed by PECS consolidation in vacuum at a sintering temperatures ranging from 1100 to 1300 °C with various heating rates between 2 and 100 °C/min and under an applied pressures from 40 to 100 MPa. Slow heating rate and high-pressure lead to highly densified and transparent Cr-doped Al₂O₃ polycrystals at sintering temperature of 1200 °C.     

Influence of sintering temperature and holding time on the densification, phase transformation, microstructure and properties of hot pressing WC-40 vol.%Al2O3 composites

WC-40 vol.%Al₂O₃ composites were prepared by high energy ball milling followed by hot pressing. The tungsten carbide (WC) and commercial alumina (Al₂O₃) powders composed of amorphous Al₂O₃, boehmite (AlOOH) and χ-Al₂O₃ were used as the starting materials. The phase transformation during sintering, the influence of sintering temperature and holding time on the densification, microstructure, Vickers hardness and fracture toughness and the toughening effects of WC-40 vol.%Al₂O₃ composites were investigated. The results showed that the amorphous Al₂O₃, AlOOH and χ-Al₂O₃ were transformed to α-Al₂O₃ completely during the sintering process. With the increasing sintering temperature and holding time, the relative density increased and both the Vickers hardness and fracture toughness increased initially to the maximum values and then decreased. When the as milled powders were hot pressed at 1540 °C for 90 min, a relative density of 97.98% and a maximum hardness of 18.65 GPa with an excellent fracture toughness of 10.43 MPa m^1/2 of WC-40 vol.%Al₂O₃ composites were obtained.     

A crucial role of O2 and O2 on mayenite structure for biomass tar steam reforming over Ni/Ca12Al14O33

Newly synthesized nickel calcium aluminum catalysts (Ni/Ca₁₂Al₁₄O₃₃) were tested in a fixed bed reactor for biomass tar steam reforming, toluene as tar destruction model compound. Four catalysts (Ni/Ca₁₂Al₁₄O₃₃) were prepared with Ni loading amount from 1, 3, 5 to 7 wt%, even 1% loading catalyst also showed excellent performance. Catalysts aged experiments in the absence (60 h on stream) and presence of H₂S were characterized by BET, X-ray diffraction (XRD), and Raman spectra. It was observed that Ni/Ca₁₂Al₁₄O₃₃ showed excellent sustainability against coke formation due to the “free oxygen” in the catalysts. It also exhibited higher H₂S-poisoning resistance property compared to the commercial catalysts Ni/Al₂O₃ (5%) and Ni/CaO_0.5/MgO_0.5. Raman spectra revealed that “free oxygen O₂⁻ and O₂²⁻” in the structure of the catalysts could be substituted by sulfur then protected Ni poisoning on some degree, but reactivation experiments by O₂ flowing showed that the sulfide Ni/Ca₁₂Al₁₄O₃₃ was difficult to completely restore, incorporation of sulfur in the structure only partly regain by O₂. The kinetic model proposes, as generally accepted, a first-order reaction for toluene with activation energy of 82.06 kJ mol⁻¹ was coincident with the literature data. The Ni/Ca₁₂Al₁₄O₃₃ catalyst was effective and relative cheap, which may be lead to reduction in the cost of hot gas cleaning process.     

Properties and rapid consolidation of nanostructured Al2O3-Al2SiO5 composites by high frequency induction heated sintering

The rapid sintering of nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites was investigated by a high-frequency induction heating sintering process. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition of grain growth. Highly dense nanostructured Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were produced with simultaneous application of a 80 MPa pressure and induced output current of a total power capacity (15 kW) within 3 min. The sintering behavior, grain size and mechanical properties of Al₂O₃ and Al₂O₃ to Al₂SiO₅ composites were investigated.     

Dielectric properties and microstructures of CaSiO3 ceramics with B2O3 addition

The effects of B₂O₃ additives on the sintering behavior, microstructure and dielectric properties of CaSiO₃ ceramics have been investigated. The B₂O₃ addition resulted in the emergence of CaO–B₂O₃–SiO₂ glass phase, which was advantageous to lower the synthesis temperature of CaSiO₃ crystal phase, and could effectively lower the densification temperature of CaSiO₃ ceramic to as low as 1100 °C. The 6 wt% B₂O₃-doped CaSiO₃ ceramic sintered at 1100 °C possessed good dielectric properties: _r = 6.84 and tan δ = 6.9 × 10⁻⁴ (1 MHz).     

Effect of CeO2 addition on densification and microstructure of Al2O3-YSZ composites

Alumina (Al₂O₃) and alumina-yttria stabilized zirconia (YSZ) composites containing 3 and 5 mass% ceria (CeO₂) were prepared by spark plasma sintering (SPS) at temperatures of 1350-1400 °C for 300 s under a pressure of 40 MPa. Densification, microstructure and mechanical properties of the Al₂O₃ based composites were investigated. Fully dense composites with a relative density of approximately 99% were obtained. The grain growth of alumina was inhibited significantly by the addition of 10 vol% zirconia, and formation of elongated CeAl₁₁O₁₈ grains was observed in the ceria containing composites sintered at 1400 °C. Al₂O₃-YSZ composites without CeO₂ had higher hardness than monolithic Al₂O₃ sintered body and the hardness of Al₂O₃-YSZ composites decreased from 20.3 GPa to 18.5 GPa when the content of ZrO₂ increased from 10 to 30 vol%. The fracture toughness of Al₂O₃ increased from 2.8 MPa m^1/2 to 5.6 MPa m^1/2 with the addition of 10 vol% YSZ, and further addition resulted in higher fracture toughness values. The highest value of fracture toughness, 6.2 MPa m^1/2, was achieved with the addition of 30 vol% YSZ.     

Sintering mechanism and dielectric properties of LiTaO3 matrix composites with the addition of Al2O3 particles

Highly densified Al₂O₃/LiTaO₃ (ALT) ceramic composites were fabricated by hot-pressing in a nitrogen atmosphere. The addition of Al₂O₃ particles could significantly improve the densification of LiTaO₃. Sintering mechanism of the LiTaO₃ ceramic incorporated with Al₂O₃ particles is proposed. Dielectric constant of 5 vol.% Al₂O₃/LiTaO₃ (5ALT) composite ceramic was slightly increased in the range from 30 kHz to 10⁶ Hz, but the dielectric loss was lowered in the whole range from 10³ Hz to 10⁶ Hz. Piezoelectric constant (d₃₃) of the 5ALT ceramic composite is about 50% of that of LiTaO₃ single crystal.     

Low-temperature firing and microwave dielectric properties of 16CaO–9Li2O–12Sm2O3–63TiO2 ceramics with V2O5 addition

The sintering behaviors and microwave dielectric properties of the 16CaO–9Li₂O–12Sm₂O₃–63TiO₂ (abbreviated CLST) ceramics with different amounts of V₂O₅ addition had been investigated in this paper. The sintering temperature of the CLST ceramic had been efficiently decreased by nearly 100 °C. No secondary phase was observed in the CLST ceramics and complete solid solution of the complex perovskite phase was confirmed. The CLST ceramics with small amounts of V₂O₅ addition could be well sintered at 1200 °C for 3 h without much degradation in the microwave dielectric properties. Especially, the 0.75 wt.% V₂O₅-doped ceramics sintered at 1200 °C for 3 h have optimum microwave dielectric properties of Kr = 100.4, Q × f = 5600 GHz, and TCF = 7 ppm/°C. Obviously, V₂O₅ could be a suitable sintering aid that improves densification and microwave dielectric properties of the CLST ceramics.     

Non-thermal plasma-assisted catalytic NOx storage over Pt/Ba/Al2O3 at low temperatures

NO_x storage performances have been investigated on a Pt/Ba/Al₂O₃ catalyst by comparison using two types of non-thermal plasma (NTP) reactor: the “PDC system” reactor and the “PFC system” reactor. In the PDC system, the catalyst was placed in the discharge space and was activated by the plasma directly, whereas in the PFC system, the plasma reactor was followed by the catalyst. The results showed that the NO_x storage capacity (NSC) of the Pt/Ba/Al₂O₃ catalyst was significantly enhanced by the non-thermal plasma in the PDC and PFC system, and the PDC system exhibited better promotional effect than the PFC system in the temperature range of 100–300 °C. The NSC of the catalyst was increased with the increase of the input energy density both in the PDC and PFC system due to the higher NO oxidation at higher input energy density. It was also found that the ionic wind induced by plasma in the PDC system enhanced the quantity of the NO adsorbed onto the catalyst surface and therefore could react with the O-radical to form more NO₂, and thus promote the formation of nitrate on the catalyst.     

Nanodispersed Au/Al2O3 catalysts for low-temperature CO oxidation: Results of research activity at the Boreskov Institute of Catalysis

This paper presents some important results of the studies on preparation and catalytic properties of nanodispersed Au/Al₂O₃ catalysts for low-temperature CO oxidation, which are carried out at the Boreskov Institute of Catalysis (BIC) starting from 2001. The catalysts with a gold loading of 1–2 wt.% were prepared via deposition of Au complexes onto different aluminas by means of various techniques (“deposition-precipitation” (DP), incipient wetness, “chemical liquid-phase grafting” (CLPG), chemical vapor deposition (CVD)). These catalysts have been characterized comparatively by a number of physical methods (XRD, TEM, diffuse reflectance UV/vis and XPS) and catalytically tested for combustion of CO impurity (1%) in wet air stream at near-ambient temperature. Using the hydroxide or chloride gold complexes capable of chemical interaction with the surface groups of alumina as the catalyst precursors (DP and incipient wetness techniques, respectively) produces the catalysts that contain metallic Au particles mainly of 2–4 nm in diameter, uniformly distributed between the external and internal surfaces of the support granules together with the surface “ionic” Au oxide species. Application of organogold precursors gives the supported Au catalysts of egg shell type which are either close by mean Au particle size to what we obtain by DP and incipient wetness techniques (CVD of (CH₃)₂Au(acac) vapor on highly dehydrated Al₂O₃ in a rotating reactor under static conditions) or contain Au crystallites of no less than 7 nm in size (CLPG method). Regardless of deposition technique, only the Cl-free Au/Al₂O₃ catalysts containing the small Au particles (d_i ≤ 5 nm) reveal the high catalytic activity toward CO oxidation under near-ambient conditions, the catalyst stability being provided by adding the water vapor into the reaction feed. The results of testing of the nanodispersed Au/Al₂O₃ catalysts under conditions which simulate in part removal of CO from ambient air or diesel exhaust are discussed in comparison with the data obtained for the commercial Pd and Pt catalysts under the same conditions.     

Effect of SO2 on the catalytic activity of Ga2O3–Al2O3 for the selective reduction of NO with propene in the presence of oxygen

The effect of coexisting SO₂ on the catalytic activity of Ga₂O₃–Al₂O₃ prepared by impregnation, coprecipitation and sol–gel method for NO reduction by propene in the presence of oxygen was studied. Although the activity of Al₂O₃ and Ga₂O₃–Al₂O₃ prepared by impregnation (Ga₂O₃/Al₂O₃(I)) and coprecipitation (Ga₂O₃–Al₂O₃(CP)) was depressed considerably by the presence of SO₂, NO conversion on Ga₂O₃–Al₂O₃ prepared by sol–gel method (Ga₂O₃–Al₂O₃(S)) was not decreased but increased slightly by SO₂ at temperatures below 723 K. From catalyst characterization, SO₂ treatment was found to cause two important effects on the surface properties: one is the creation of Brønsted acid sites on which propene activation is promoted (positive effect), and the other is the poisoning of NO_x adsorption sites on which NO reduction proceeds (negative effect). It was presumed that the influence of SO₂ treatment on the catalytic activity is strongly related to the balance between the negative and positive. The activity enhancement of Ga₂O₃–Al₂O₃(S) by SO₂ was accounted for by the following consideration: (1) increase of the propene activation ability by SO₂, (2) incomplete inhibition of NO_x adsorption sites by SO₂.     

Effect of sintering temperature on varistor properties and aging characteristics of ZnO–V2O5–MnO2 ceramics

The microstructure, electrical properties, dielectric characteristics, and DC accelerated aging behavior of the ZVM-based varistors were investigated for different sintering temperatures of 800–950 °C. The microstructure of the ZVM-based ceramics consisted of mainly ZnO grain and secondary phase Zn₃(VO₄)₂, which acts as liquid-phase sintering aid. The Zn₃(VO₄)₂ has a significant effect on the sintered density, in the light of an experimental fact, which the decreases of the Zn₃(VO₄)₂ distribution with increasing sintering temperature resulted in the low sintered density. The breakdown field exhibited the highest value (17,640 V/cm) at 800 °C in the sintering temperature and the lowest value (992 V/cm) at 900 °C in the sintering temperature. The nonlinear coefficient exhibited the highest value, reaching 38 at 800 °C and the lowest value, reaching 17 at 850 °C. The varistor sintered at 900 °C exhibited not only high nonlinearity with 27.2 in nonlinear coefficient, but also the highest stability, in which %ΔE_1 mA = −0.6%, %Δα = −26.1%, and %Δ tan δ = +21.8% for DC accelerated aging stress of 0.85 E_1 mA/85 °C/24 h.