Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts

The present work deals with some machinability studies on flank wear, surface roughness, chip morphology and cutting forces in finish hard turning of AISI 4340 steel using uncoated and multilayer TiN and ZrCN coated carbide inserts at higher cutting speed range. The process has also been justified economically for its effective application in hard turning. Experimental results revealed that multilayer TiN/TiCN/Al₂O₃/TiN coated insert performed better than uncoated and TiN/TiCN/Al₂O₃/ZrCN coated carbide insert being steady growth of flank wear and surface roughness. The tool life for TiN and ZrCN coated carbide inserts was found to be approximately 19 min and 8 min at the extreme cutting conditions tested. Uncoated carbide insert used to cut hardened steel fractured prematurely. Abrasion, chipping and catastrophic failure are the principal wear mechanisms observed during machining. The turning forces (cutting force, thrust force and feed force) are observed to be lower using multilayer coated carbide insert in hard turning compared to uncoated carbide insert. From 1st and 2nd order regression model, 2nd order model explains about 98.3% and 86.3% of the variability of responses (flank wear and surface roughness) in predicting new observations compared to 1st order model and indicates the better fitting of the model with the data for multilayer TiN coated carbide insert. For ZrCN coated carbide insert, 2nd order flank wear model fits well compared to surface roughness model as observed from ANOVA study. The savings in machining costs using multilayer TiN coated insert is 93.4% compared to uncoated carbide and 40% to ZrCN coated carbide inserts respectively in hard machining taking flank wear criteria of 0.3 mm. This shows the economical feasibility of utilizing multilayer TiN coated carbide insert in finish hard turning.     

Performance studies of multilayer hard surface coatings (TiN/TiCN/Al2O3/TiN) of indexable carbide inserts in hard machining: Part-II (RSM,grey relational and techno economical approach)

This paper presents the mathematical modelling and parametric optimization on flank wear and surface roughness based on response surface methodology and grey-based Taguchi method in finish hard turning of AISI 4340 steel (HRC 47 ± 1) using multilayer coated carbide (TiN/TiCN/Al₂O₃/TiN) insert under dry environment. The economical feasibility of utilizing multilayer TiN coated carbide insert has been described. Model adequacy has been checked using correlation coefficients. From main effect, it is evident that, cutting speed is the most significant factor for flank wear followed by depth of cut and feed. Again, feed is the most significant factor for surface roughness followed by cutting speed and depth of cut. The coefficient of determination (R²) is more than 75% for RSM models developed, which shows the high correlation exist between the experimental and predicted values. The experimental vs. predicted values of flank wear and surface roughness (Ra and Rz) are also found to be very close to each other implying significance of models developed. The improvement of grey relational grade from initial parameter combination (d2–f3–v4) to the optimal parameter combination (d1–f1–v3) is found to be 0.3093 using grey relational analysis coupled with Taguchi method for simultaneous optimization of responses. Flank wear (VBc) and surface roughness parameters (Ra and Rz) are decreased 1.9, 2.32 and 1.5 times respectively considering optimal parametric combinations for multi-responses. The calculated total machining cost per part is only Rs. 3.17 due to higher tool life (47 min at their optimal level) of multilayer TiN coated carbide insert. It brings to the reduction of downtime and increases the savings.     

A comparative study on performance of multilayer coated and uncoated carbide inserts when turning AISI D2 steel under dry environment

The present work deals with a comparative study on flank wear, surface roughness, tool life, volume of chip removal and economical feasibility in turning high carbon high chromium AISI D2 steel with multilayer MTCVD coated [TiN/TiCN/Al₂O₃/TiN] and uncoated carbide inserts under dry cutting environment. Higher micro hardness of TiN coated carbide samples (1880 HV) compared to uncoated carbide (1430 HV) is observed and depicts better resistance against abrasion. The low erosion rate was observed in TiN coated insert compared to uncoated carbide. The tool life of TiN coated insert is found to be approximately 30 times higher than the uncoated carbide insert under similar cutting conditions and produced lower surface roughness compared to uncoated carbide insert. The dominant wear mechanism was found to be abrasion and progression of wear was steady using multilayer TiN coated carbide insert. The developed regression model shows high determination coefficient i.e. R² = 0.977 for flank wear and 0.94 for surface roughness and accurately explains the relationship between the responses and the independent variable. The machining cost per part for uncoated carbide insert is found to be 10.5 times higher than the multilayer TiN coated carbide inserts. This indicates 90.5% cost savings using multilayer TiN coated inserts by the adoption of a cutting speed of 200 m/min coupled with a tool feed rate of 0.21 mm/rev and depth of cut of 0.4 mm. Thus, TiN coated carbide tools are capable of reducing machining costs and performs better than uncoated carbide inserts in machining D2 steel.     

Some studies on hard turning of AISI 4340 steel using multilayer coated carbide tool

Hard turning with multilayer coated carbide tool has several benefits over grinding process such as, reduction of processing costs, increased productivities and improved material properties. The objective was to establish a correlation between cutting parameters such as cutting speed, feed rate and depth of cut with machining force, power, specific cutting force, tool wear and surface roughness on work piece. In the present study, performance of multilayer hard coatings (TiC/TiCN/Al₂O₃) on cemented carbide substrate using chemical vapor deposition (CVD) for machining of hardened AISI 4340 steel was evaluated. An attempt has been made to analyze the effects of process parameters on machinability aspects using Taguchi technique. Response surface plots are generated for the study of interaction effects of cutting conditions on machinability factors. The correlations were established by multiple linear regression models. The linear regression models were validated using confirmation tests. The analysis of the result revealed that, the optimal combination of low feed rate and low depth of cut with high cutting speed is beneficial for reducing machining force. Higher values of feed rates are necessary to minimize the specific cutting force. The machining power and cutting tool wear increases almost linearly with increase in cutting speed and feed rate. The combination of low feed rate and high cutting speed is necessary for minimizing the surface roughness. Abrasion was the principle wear mechanism observed at all the cutting conditions.     

TURNING STUDIES OF DEEP CRYOGENIC TREATED P-40 TUNGSTEN CARBIDE CUTTING TOOL INSERTS – TECHNICAL COMMUNICATION

In the present work, coated tungsten carbide tool inserts of ISO P-40 grade were subjected to deep cryogenic treatment at ?176°C. Turning studies were conducted on AISI 1040 workpieces using both untreated and deep cryogenic treated tungsten carbide cutting tool inserts. The turning performance was evaluated in terms of flank wear of the cutting tool inserts, main cutting force and surface finish of the machined workpieces. The flank wear of deep cryogenic treated carbide tools was observed to be lower than that of untreated carbide tools in machining of AISI 1040 steel. The cutting force during machining of AISI 1040 steel was lower with the deep cryogenic treated carbide tools when compared with the untreated carbide tools. The surface finish produced on machined AISI 1040 steel workpieces was superior with the deep cryogenic treated carbide tools as compared to the untreated carbide tools.     

EFFECT OF CUTTING SPEED AND SURFACE CHEMISTRY OF CUTTING TOOLS ON THE FORMATION OF BUL OR BUE AND SURFACE QUALITY OF THE GENERATED SURFACE IN DRY TURNING OF AA6005 ALUMINIUM ALLOY

In the present investigation, AA6005 (ISO: AlSiMg) alloy was machined in turning operation with different cutting tools, such as uncoated cemented carbide insert, PVD TiN coated, CVD diamond coated and PCD insert, under dry environment. Effect of cutting speed was studied for each of the cutting tools with regard to the formation of built-up layer (BUL) or built-up edge (BUE). The rake surface of the tools was characterized by optical microscopy, scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopic microanalysis. Particular emphasis was given on wear mechanism of PVD TiN coated insert, conventionally used in machining ferrous alloys, during dry turning of AA6005 alloy. It has been observed that increase of cutting speed from 200 m/min to as high as 1000 m/min could not substantially reduce formation of BUL over tool rake surface during dry machining of AA6005 alloy with uncoated or PVD TiN coated cemented carbide inserts. The potential of diamond-based tools in dry machining of aluminium alloy was also studied. Finally, the effect of cutting speed on surface finish of the workpiece machined with different cutting tools was studied during dry turning of AA6005 alloy.     

Wear behavior and cutting performance of nanostructured hard coatings on cemented carbide cutting tools in hard milling

The influence of nanolayer AlTiN/TiN and multilayer nanocomposite TiAlSiN/TiSiN/TiAlN hard coatings on the wear behavior and cutting performance of carbide cutting tools was investigated in face milling of hardened AISI O2 cold work tool steel (∼58 HRC) at dry conditions. Characterization of the coatings was performed using nanoindentation, scratch test, reciprocating multi-pass wear test. The chips forming during cutting process were also analyzed. Results showed that abrasive and oxidation wear are dominant tool failures. The nanolayer AlTiN/TiN coating gives the best adhesion to the substrate, the best wear resistance in machining and thus provides the longest lifetime with carbide inserts.     

Performance comparison of conventional and wiper ceramic inserts in hard turning through artificial neural network modeling

Hard turning with ceramic tools provides an alternative to grinding operation in machining high precision and hardened components. But, the main concerns are the cost of expensive tool materials and the effect of the process on machinability. The poor selection of cutting conditions may lead to excessive tool wear and increased surface roughness of workpiece. Hence, there is a need to investigate the effects of process parameters on machinability characteristics in hard turning. In this work, the influence of cutting speed, feed rate, and machining time on machinability aspects such as specific cutting force, surface roughness, and tool wear in AISI D2 cold work tool steel hard turning with three different ceramic inserts, namely, CC650, CC650WG, and GC6050WH has been studied. A multilayer feed-forward artificial neural network (ANN), trained using error back-propagation training algorithm has been employed for predicting the machinability. The input?Coutput patterns required for ANN training and testing are obtained from the turning experiments planned through full factorial design. The simulation results demonstrate the effectiveness of ANN models to analyze the effects of cutting conditions as well as to study the performance of conventional and wiper ceramic inserts on machinability.     

Tool life and wear mechanism of coated and uncoated Al2O3/TiCN mixed ceramic tools in turning hardened alloy steel

The focus of this paper is the continuous turning of hardened AISI 52100 (～63HRc) using coated and uncoated ceramic Al₂O₃–TiCN mixed inserts, which are cheaper than cubic boron nitride (CBN) or polycrystalline cubic boron nitride (PCBN). The machinability of hardened steel was evaluated by measurements of tool wear, tool life, and surface finish of the workpiece. Wear mechanisms and patterns of ceramic inserts in hard turning of hardened AISI 52100 are discussed. According to the results obtained, fracture and chipping type damages occur more frequently in uncoated tools, whereas crater wear is the more common type of damage in TiN coated tools. Most important result obtained from the study is that TiN coating and crater wear affect chip flow direction. In uncoated ceramic tool, the crater formation results in decrease of chip up-curl radius. Besides, uncoated cutting tool results in an increase in the temperature at the tool chip interface. This causes a thermal bi-metallic effect between the upper and lower sides of the chip that forces the chip to curl a smaller radius. Chips accumulate in front of the tool and stick to the workpiece depending on the length of the cutting time. This causes the surface quality to deteriorate. TiN coating not only ensures that the cutting tool is tougher, but also ensures that the surface quality is maintained during cutting processes.     

Wear behaviors of single-layer and multi-layer coated carbide inserts in high speed machining of hardened AISI 4340 steel

Flank wear progression and wear mechanisms of uncoated, coated with PVD applied single-layer TiAlN, and CVD applied multi-layer MT-TiCN/Al₂O₃/TiN cemented carbide inserts were analyzed during dry turning of hardened AISI 4340 steel (35 HRC). Experimental observations indicate that by applying a coating to the uncoated insert the limiting cutting speed increase from 62 to 200 m/min, which further extends up-to 300–350 m/min when using multi-layer coating scheme. Relatively lower wear rate seen when using single-layer TiAlN coated inserts. However, after removal of the thin layer of coating the wear rate increase rapidly, subsequently dominates the wear rate of multi-layer coated inserts. Cutting forces; especially axial and radial components have also shown the similar behavior and increase rapidly when the tool failure occurs. Flank wear, crater wear and catastrophic failure are the dominant forms of tool wear. Digital microscope and SEM images coupled with elemental analysis (EDAX) have been taken at various stages of tool life for understanding the wear mechanisms.     

Performance of coated and uncoated mixed ceramic tools in hard turning process

The present contribution deals with the study of the effects of cutting speed, feed rate and depth of cut on the performance of machining which traditionally named “machinability”. The focus is made on the effect of the pre-cited cutting parameters on the evolution of surface roughness and cutting force components during hard turning of AISI D3 cold work tool steel with CC6050 and CC650 ceramic inserts. Also, for both ceramics a comparison of their wear evolution with time and its impact on the surface equality was proposed. The planning of experiments was based on Taguchi’s L₁₆ orthogonal array. The analysis of variance (ANOVA), the signal-to-noise ratio and response surface methodology (RSM) were adopted. Consequently, the validity of proposed linear regression model was checked and the most important parameter affecting the surface roughness and cutting force components were determined. Furthermore, in order to determine the levels of the cutting regime that lead to minimum surface roughness and minimum machining force the relationship between cutting factors was analyzed. The results revealed that the surface quality obtained with the coated CC6050 ceramic insert is 1.6 times better than the one obtained with uncoated CC650 ceramic insert. However, the uncoated ceramic insert was useful in reducing the machining force.     

Performance evaluation of CBN,coated carbide,cryogenically treated uncoated/coated carbide inserts in finish-turning of hardened steel

In the present work, the performance of cubic boron nitride (CBN) inserts was compared with coated carbide and cryogenically treated coated/uncoated carbide inserts in terms of flank wear, surface roughness, white layer formation, and microhardness variation under dry cutting conditions for finish turning of hardened AISI H11 steel (48–49 HRC). The flank wear of CBN tools was observed to be lower than that of other inserts, but the accumulated machining time for all the four edges of carbide inserts were nearer to or better than the PCBN inserts. Results showed that tool life of carbide inserts decreased at higher cutting speeds. The surface roughness achieved under all cutting conditions for coated-carbide-treated/untreated inserts was comparable with that achieved with CBN inserts and was below 1.6 μm. The white layer formation and microhardness variation is less while turning with cryogenically treated carbide inserts than the CBN and untreated carbide. At low to medium cutting speed and feed, the performance of carbide inserts was comparable with CBN both in terms of tool life and surface integrity.     

Performance assessment of microwave treated WC insert while turning AISI 1040 steel

This study attributed to post treatment of tungsten carbide (WC) inserts using microwave irradiation. Tungsten carbide inserts were subjected to microwave radiation (2.45 GHz) to enhance its performance in terms of reduction in tool wear rate, cutting force surface roughness and improvement in tool life. Performance of tungsten carbide insert is very much affected by machine operating parameters i.e. speed, feed and depth of cut. An attempt has been made to investigate the effects of machining parameters on microwave treated tool inserts. This paper describes the comparative study of machining performance of untreated and microwave treated WC tool inserts used for turning of AISI 1040 steel. Machining performance has been evaluated in terms of flank wear, cutting force, surface roughness, tool wear mechanisms. Critical examinations of tool wear mechanisms and improvements in metallurgical properties such as microstructural change, phase activation of WC grains were identified using scanning electron microscope (SEM). Results obtained from the turning using the microwave treated tool inserts showed a significant reduction tool wear thereby enhancing the surface quality of workpiece.     

Tool vibration in internal turning of hardened steel using cBN tool

The machining of hardened materials with hardness over 45 HRC has been an alternative to grinding since the 1970s, with the commercial availability of cubic boron nitride (cBN) and ceramic tools. However, the low toughness of these types of tool materials makes them very sensitive to damages caused by vibrations, which are critical for operations like internal turning, where the tool resembles a cantilever beam and therefore is susceptible to large deflections. This work aims to contribute to the study of tool performance in internal turning of long holes in hardened AISI 4340 steel in finishing conditions. Different machining conditions, two different tool holders (steel and carbide), and several tool overhangs were tested. The surface finish, acceleration (vibration) signals, and tool wear of cBN inserts were evaluated. The results show that vibration and the material of the tool holder may play a secondary role in the surface finish for stable turning, but the use of carbide tool holders makes the process stable for longer tool overhangs. Moreover, when the cutting becomes unstable, surface roughness is increased severely.     

Optimization of surface roughness and tool wear in hard turning of austempered ductile iron (grade 3) using Taguchi method

In this work, the cutting parameters are optimized in hard turning of ADI using carbide inserts based on Taguchi method. The cutting insert CVD coated with AL₂O₃/MT TICN. Experiments have been carried out in dry condition using L₁₈ orthogonal array. The cutting parameters selected for machining are cutting speed, feed rate and depth of cut with each three levels, nose radius in two levels maintaining other cutting parameters constant. The ANOVA and signal to noise ratio are used to optimize the cutting parameters. The cutting speed is the most dominant factor affecting the surface roughness and tool wear. In optimum cutting condition, the confirmation tests are carried out. The optimum cutting condition results are predicted using signal to noise ratio and regression analysis. The predicted and experimental values for surface roughness and tool wear adhere closer to 9.27% and 1.05% of deviations respectively.     

Performance Evaluation of a Hard Composite Solid Lubricant Coating When Dry Machining of High-carbon Steel

A novel hard composite solid lubricant coating combining TiN and MoS_x has been developed using pulsed DC closed-field unbalanced magnetron sputtering (CFUBMS). The tribological and mechanical properties together with their interdependencies with the coating microstructures have been assessed and reported elsewhere. This article evaluates the machining performance and correlates the underlying tribological aspects of different TiN-MoS_x coating architectures (deposited at titanium (Ti) cathode currents of 1, 3.5, and 5 A) when dry turning AISI 1080 high-carbon steel. A comparative performance study clearly established the supremacy of the composite coating (deposited at 3.5 A Ti cathode current with ～12 wt% of MoS_x) with a hard TiN underlayer over monolayer TiN, MoS_x, and other related coating architectures in terms of cutting force, tool wear, and workpiece surface roughness. The superlubricity behavior of the said composite coated tool resulted in a reduction of cutting force (by up to ～45% compared to the uncoated tool) and exhibited a tool life of 8 min, which was eight times and more than two times longer than that of the uncoated and conventional hard TiN coated counterparts, respectively. The workpiece surface roughness, R_a, also decreased by 13 to 21% when machined with the TiN-MoS_x coated tool in comparison to the uncoated cemented carbide.     

Behavior of Coated Carbide Tools in High Speed Machining of a Nickel Base Alloy

Multilayer TiN/TiCN/TiN and single-layer TiAIN PVD coated carbide tools were used to machine a nickel base, C-263, alloy at high-speed conditions in order to investigate their performance in terms of tool life, surface finish and component forces generated during machining. The test results show that the triple layer, TiN/TiCN/TiN, coated inserts gave longer tool life when machining at higher speed and depth of cut conditions while the single layer, TiA/N, coated inserts produced better surface finish. The feed forces recorded were generally higher than the cutting forces. This could perhaps be attributed to the adverse effect of burr formation and work hardening of the workpiece associated with prolonged machining. Analysis of the test results indicate that the difference in thermal properties and tribo-chemical behaviour of both the coating and substrate materials are the major factors influencing the tribo-contact at the tool-chip interface during machining. Wear mechanisms of the coating materials can also affect tool performance in terms of tool life, surface finish and component forces.     

Performance evaluation of PVD TIALN coated carbide tools vis-à-vis uncoated carbide tool in turning of titanium alloy (Ti-6Al-4V) by simultaneous minimization of cutting energy,dimensional deviation and tool wear

Titanium alloys are difficult-to-machine materials because of their poor machinability characteristics. Machining and machining performance evaluation for such materials is still a challenge. Individual machining performance indices like cutting forces, cutting energy and tool wear lead to ambiguous understanding. In this work, a Cumulative Performance Index (CPI) is defined which amalgamates non-dimensional forms of specific cutting energy, back force and average principal flank wear in turning. The CPI focuses upon simultaneous minimization of specific cutting energy, dimensional deviation and average principal flank wear. The defined index is then used to evaluate performance of five commercially available physical vapor deposited (PVD) TiAlN coated tungsten carbide/cobalt inserts vis-à-vis uncoated tungsten carbide/cobalt insert in turning of Ti-6Al-4V. Cutting forces were monitored during turning and tool wear was measured after turning experiments. The results showed that the performance of coated inserts was either comparable or poor than uncoated insert; and in no case, coated inserts performed better than uncoated insert. Although commercial recommendations are in place to use PVD coated inserts for enhanced machinability of titanium alloys, the use of coated inserts is not justified keeping in view the energy spent in coating and insignificant improvement in performance.     

Performance of Uncoated and Coated Carbide Tools in the Ultra-Precision Machining of Stainless Steel

Ultra-precision machines are widely used to turn aspherical or spherical profiles on mould inserts for the injection moulding of optical lenses. During the turning of a profile on a stainless steel mould insert, the cutting speed reduces significantly to 0 as the cutting tool is fed towards the centre of the machined profile. This paper reports experiments carried out to study the wear of uncoated and PVD-coated carbide tools (carbide tool coated with 2000 alternate layers of AlN and TiN, each layer 1.5 nm and carbide tool coated with 0.5 m TiN, 5.5 m TiCN and 0.5 m TiN) in the ultra-precision machining of STAVAX (modified AISI 420 stainless steel) at low speeds with and without lubricant. A sprayed mixture of compressed air, liquid paraffin oil and cyclomethicone was used as lubricant. Examination of the wear at the rake face of the tool suggests that during machining of the alloy with a hardness of 55 HRC without lubricant, the cutting edge is subjected to high compressive stress, resulting in fracture. Reducing the hardness of the alloy would therefore result in a lower stress acting on the cutting edge, thus rendering the tool less susceptible to fracture. Both the rake and the flank faces of the coated tools exhibited lower wear than the uncoated tools. This was due to the former tools possessing higher fracture resistance owing to the presence of the coating. The lubricant was effective in improving surface finish, preventing surface fracture and reducing flank wear.     

Investigation of the performance of carbide cutting tools with hard coatings in hard milling based on the response surface methodology

Machining of hard materials has become a great challenge for several decades. One of the problems in this machining process is early tool wear, and this affects the machinability of hard materials. In order to increase machinability, cutting tools are widely coated with nanostructured physical vapor deposition hard coatings. The main characteristics of such advanced hard coatings are high microhardness and toughness as well as good adhesion to the substrate. In this paper, the influence of hard coatings (nanolayer AlTiN/TiN, multilayer nanocomposite TiAlSiN/TiSiN/TiAlN, and commercially available TiN/TiAlN) and cutting parameters (cutting speed, feed rate, and depth of cut) on cutting forces and surface roughness were investigated during face milling of AISI O2 cold work tool steel (～61 HRC). The experiments were conducted based on 3¹³ factorial design by response surface methodology, and response surface equations of cutting forces and surface roughness were obtained. In addition, the cutting forces obtained with the coated and uncoated tools were compared. The results showed that the interaction of coating type and depth of cut affects surface roughness. The hard coating type has no significant effect on cutting forces, while the cutting force F _z is approximately two times higher in the case of uncoated tool.