A 40-Gb/s Transimpedance Amplifier in 0.18-$mu$m CMOS Technology

A 40-Gb/s transimpedance amplifier (TIA) is realized in 0.18-mum CMOS technology. From the measured S-parameters, a transimpedance gain of 51 dBOmega and a 3-dB bandwidth up to 30.5 GHz were observed. A bandwidth enhancement technique, pi-type inductor peaking (PIP), is proposed to achieve a bandwidth enhancement ratio (BWER) of 3.31. In addition, the PIP topology used at the input stage decreases the noise current as the operation frequency increases. Under a 1.8 V supply voltage, the TIA consumes 60.1 mW with a chip area of 1.17 X 0.46 mm2. The proposed CMOS TIA presents a gain-bandwidth product per DC power figure of merit (GBP/P_de) of 180.1 GHzOmega/mW.     

1.25-Gb/s regulated cascode CMOS transimpedance amplifier for Gigabit Ethernet applications

A transimpedance amplifier (TIA) has been realized in a 0.6-/spl mu/m digital CMOS technology for Gigabit Ethernet applications. The amplifier exploits the regulated cascode (RGC) configuration as the input stage, thus achieving as large effective input transconductance as that of Si Bipolar or GaAs MESFET. The RGC input configuration isolates the input parasitic capacitance including photodiode capacitance from the bandwidth determination better than common-gate TIA. Test chips were electrically measured on a FR-4 PC board, demonstrating transimpedance gain of 58 dB/spl Omega/ and -3-dB bandwidth of 950 MHz for 0.5-pF photodiode capacitance. Even with 1-pF photodiode capacitance, the measured bandwidth exhibits only 90-MHz difference, confirming the mechanism of the RGC configuration. In addition, the noise measurements show average noise current spectral density of 6.3 pA//spl radic/(Hz) and sensitivity of -20-dBm for a bit-error rate of 10/sup -12/. The chip core dissipates 85 mW from a single 5-V supply.     

1-Gb/s 80-dB/spl Omega/ fully differential CMOS transimpedance amplifier in multichip on oxide technology for optical interconnects

A 1-Gb/s differential transimpedance amplifier (TIA) is realized in a 0.25-/spl mu/m standard CMOS technology, incorporating the regulated cascode input configuration. The TIA chip is then integrated with a p-i-n photodiode on an oxidized phosphorous-silicon (OPS) substrate by employing the multichip-on-oxide (MCO) technology. The MCO TIA demonstrates 80-dB/spl Omega/ transimpedance gain, 670-MHz bandwidth for 1-pF photodiode capacitance, 0.54-/spl mu/A average input noise current, -17-dBm sensitivity for 10/sup -12/ bit-error rate (BER), and 27-mW power dissipation from a single 2.5-V supply. It also shows negligible switching noise effect from an embedded VCO on the OPS substrate. Furthermore, a four-channel MCO TIA array is implemented for optical interconnects, resulting in less than -40-dB crosstalk between adjacent channels.     

SiGe differential transimpedance amplifier with 50-GHz bandwidth

InP and SiGe technologies are both attractive for design of circuits operating at 40 GB/s and beyond. In this paper, we describe a fully differential SiGe transimpedance amplifier (TIA) suitable for differential phase-shift keying applications. The TIA exhibits 49 dB-/spl Omega/ transimpedance, greater than 50-GHz bandwidth, and input-referred current noise less than 30 pA//spl radic/Hz. For comparison, we have also developed a similar TIA in an InP double-heterostructure bipolar transistor technology. The InP TIA had 48 dB-/spl Omega/ transimpedance and 49-GHz bandwidth.     

Broad-Band Design Techniques for Transimpedance Amplifiers

In this paper, a novel bandwidth enhancement technique based on the combination of capacitive degeneration, broad-band matching network, and the regulated cascode (RGC) input stage is proposed and analyzed, which turns the transimpedance amplifier (TIA) design into a fifth-order low-pass filter with Butterworth response. This broad-band design methodology for TIAs is presented with an example implemented in CHRT 0.18-mum 1.8-V RF CMOS technology. Measurement data shows a -3-dB bandwidth of about 8 GHz with 0.25-pF photodiode capacitance. Comparing with the core RGC TIA without capacitive degeneration and broad-band matching network, this design achieves an overall bandwidth enhancement ratio of 3.6 with very small gain ripple. The transimpedance gain is 53 dBOmega with a group delay of 80plusmn20 ps. The chip consumes only 13.5-mW dc power and the measured average input-referred noise current spectral density is 18 pA/radicHz up to 10 GHz     

High-gain differential CMOS transimpedance amplifier with on-chip buried double junction photodiode

An integrated fully differential CMOS transimpedance amplifier (TIA) with buried double junction photodiode input is described. The TIA features a variable high transimpedance gain (250 k/spl Omega/ to 2.5 M/spl Omega/), large DC photocurrent rejection capability (>55 dB) and low input referred noise density at 100 kHz (2pA//spl radic/Hz).     

Bandwidth enhancement for transimpedance amplifiers

A technique for bandwidth enhancement of a given amplifier is presented. Adding several interstage passive matching networks enables the control of transfer function and frequency response behavior. Parasitic capacitances of cascaded gain stages are isolated from each other and absorbed into passive networks. A simplified design procedure, using well-known low-pass filter component values, is introduced. To demonstrate the feasibility of the method, a CMOS transimpedance amplifier (TIA) is implemented in a 0.18-/spl mu/m BiCMOS technology. It achieves 3 dB bandwidth of 9.2 GHz in the presence of a 0.5-pF photodiode capacitance. This corresponds to a bandwidth enhancement ratio of 2.4 over the amplifier without the additional passive networks. The transresistance gain is 54 dB/spl Omega/, while drawing 55 mA from a 2.5-V supply. The input sensitivity of the TIA is -18 dBm for a bit error rate of 10/sup -12/.     

Design of a low-power 3.5-GHz broad-band CMOS transimpedance amplifier for optical transceivers

This paper describes a novel low-power low-noise CMOS voltage-current feedback transimpedance amplifier design using a low-cost Agilent 0.5-/spl mu/m 3M1P CMOS process technology. Theoretical foundations for this transimpedance amplifier by way of gain, bandwidth and noise analysis are developed. The bandwidth of the amplifier was extended using the inductive peaking technique, and, simulation results indicated a -3-dB bandwidth of 3.5 GHz with a transimpedance gain of /spl ap/60 dBohms. The dynamic range of the amplifier was wide enough to enable an output peak-to-peak voltage swing of around 400 mV for a test input current swing of 100 /spl mu/A. The output noise voltage spectral density was 12 nV//spl radic/Hz (with a peak of /spl ap/25 nV//spl radic/Hz), while the input-referred noise current spectral density was below 20 pA//spl radic/Hz within the amplifier frequency band. The amplifier consumes only around 5 mA from a 3.3-V power supply. A test chip implementing the transimpedance amplifier was also fabricated using the low-cost CMOS process.     

6-k/spl Omega/ 43-Gb/s differential transimpedance-limiting amplifier with auto-zero feedback and high dynamic range

A high-gain, 43-Gb/s InP HBT transimpedance-limiting amplifier (TIALA) with 100-/spl mu/A/sub pp/ sensitivity and 6 mA/sub pp/ input overload current is presented. The circuit also operates as a limiting amplifier with 40-dB differential gain, better than 15-dB input return loss, and a record-breaking sensitivity of 8 mV/sub pp/ at 43 Gb/s. It features a differential TIA stage with inductive noise suppression in the feedback network and consumes less than 450mW from a single 3.3-V supply. The TIALA has 6-k/spl Omega/ (76dB/spl Omega/) differential transimpedance gain and 35-GHz bandwidth and comprises the transimpedance and limiting gain functions, an auto-zero dc feedback circuit, signal level monitor, and slicing level adjust functions. Other important features include 45-dB isolation and 800-mV/sub pp/ differential output.     

1-Gb/s zero-pole cancellation CMOS transimpedance amplifier for Gigabit Ethernet applications

A zero-pole cancellation transimpedance amplifier (TIA) has been realized in 0.35 μm RF CMOS tech nology for Gigabit Ethernet applications. The TIA exploits a zero-pole cancellation configuration to isolate the input parasitic capacitance including photodiode capacitance from bandwidth deterioration. Simulation results show that the proposed TIA has a bandwidth of 1.9 GHz and a transimpedance gain of 65 dB·Ω for 1.5 pF photodiode capaci tance, with a gain-bandwidth product of 3.4 THz·Ω. Even with 2 pF photodiode capacitance, the bandwidth exhibits a decline of only 300 MHz, confirming the mechanism of the zero-pole cancellation configuration. The input resis tance is 50 Ω, and the average input noise current spectral density is 9.7 pA/(Hz)~(1/2). Testing results shows that the eye diagram at 1 Gb/s is wide open. The chip dissipates 17 mW under a single 3.3 V supply.     

A 1.8-V 10-Gb/s fully integrated CMOS optical receiver analog front-end

A fully integrated 10-Gb/s optical receiver analog front-end (AFE) design that includes a transimpedance amplifier (TIA) and a limiting amplifier (LA) is demonstrated to require less chip area and is suitable for both low-cost and low-voltage applications. The AFE is fabricated using a 0.18-/spl mu/m CMOS technology. The tiny photo current received by the receiver AFE is amplified to a differential voltage swing of 400 mV/sub (pp)/. In order to avoid off-chip noise interference, the TIA and LA are dc-coupled on the chip instead of ac-coupled though a large external capacitor. The receiver front-end provides a conversion gain of up to 87 dB/spl Omega/ and -3dB bandwidth of 7.6 GHz. The measured sensitivity of the optical receiver is -12dBm at a bit-error rate of 10/sup -12/ with a 2/sup 31/-1 pseudorandom test pattern. Three-dimensional symmetric transformers are utilized in the AFE design for bandwidth enhancement. Operating under a 1.8-V supply, the power dissipation is 210 mW, and the chip size is 1028 /spl mu/m/spl times/1796 /spl mu/m.     

CMOS wideband amplifiers using multiple inductive-series peaking technique

This work presents the technique of multiple inductive-series peaking to mitigate the deteriorated parasitic capacitance in CMOS technology. Employing multiple inductive-series peaking technique, a 10-Gb/s optical transimpedance amplifier (TIA) has been implemented in a 0.18-/spl mu/m CMOS process. The 10-Gb/s optical CMOS TIA, which accommodates a PD capacitor of 250 fF, achieves the gain of 61 dB/spl Omega/ and 3-dB frequency of 7.2 GHz. The noise measurement shows the average noise current of 8.2 pA//spl radic/Hz with power consumption of 70 mW.     

A 3.125-Gb/s inductorless transimpedance amplifier for optical communication in 0.35μm CMOS

A 3.125-Gb/s transimpedance amplifier(TIA) for an optical communication system is realized in 0.35μm CMOS technology.The proposed TIA employs a regulated cascode configuration as the input stage, and adopts DC-cancellation techniques to stabilize the DC operating point.In addition,noise optimization is processed. The on-wafer measurement results show the transimpedance gain of 54.2 dBΩand -3 dB bandwidth of 2.31 GHz.The measured average input referred noise current spectral density is about 18.8 pA/(?).The measured eye diagram is clear and symmetrical for 2.5-Gb/s and 3.125-Gb/s PRBS.Under a single 3.3-V supply voltage,the TIA consumes only 58.08 mW,including 20 mW from the output buffer.The whole die area is 465×435μm~2.     

Low-voltage CMOS current-mode preamplifier: analysis and design

This paper presents the analysis and design of a new low-voltage fully balanced differential CMOS current-mode preamplifier for multi-Gbps series data communications. The minimum supply voltage of the proposed preamplifier is V/sub T/+V/sub sat/. The preamplifier employs a balanced configuration to achieve large bandwidth and to minimize the effect of bias-dependent mismatches. Two new bandwidth enhancement techniques, namely inductive series peaking and current feedback that are specific to low-voltage CMOS current-mode circuits, are introduced. The inductive series peaking technique utilizes the resonant characteristics of LC networks to achieve both a flat frequency response and maximum bandwidth. Current feedback extends bandwidth, lowers input impedance, and improves dynamic range. The employment of both techniques further increases the bandwidth, reduces the value of the series peaking inductor, and improves noise performance of the pre-amplifier at high frequencies. The preamplifier has been designed using a 0.18-/spl mu/m 6-metal 1-poly 1.8-V CMOS technology. Simulation results from Spectre with BSIM3.3 device models that account for device parasitics demonstrate that the preamplifier has a flat frequency response with 25.3 dB dc current gain or equivalently 60 dB/spl Omega/ transimpedance gain with a 50-/spl Omega/ load and bandwidth of 2.15 GHz.     

A RGC-based,low-power,CMOS transimpedance amplifier for 10Gb/s optical receivers

ABSTRACT

In this paper, a new low-power transimpedance amplifier (TIA) based on a modified Regulated Cascode (RGC) circuit structure followed by a closed-loop post-amplifier is proposed for 10 Gb/s applications. The main objective of this work is to reduce the power consumption while, the frequency bandwidth of the proposed amplifier is increased considerably. The booster of a conventional RGC is modified by a cascoded transistor and its effect on the performance of the circuit is studied mathematically, which are verified by simulations. The bandwidth extension is occurred due to increasing the gain of the booster amplifier in the RGC stage, which isolates further the input capacitance and results in a reduced input resistance value hence, a higher input pole frequency is obtained in comparison with other conventional RGC structures. On the other hand, by using an active inductive peaking technique, the frequency of the output pole is also increased which results in a further extension of the frequency bandwidth for the proposed circuit. The proposed TIA is simulated using 90 nm CMOS technology parameters, which shows a 50.5 dBΩ transimpedance gain, 7.3 GHz frequency bandwidth and 1.22 µA_rms input referred noise value for only 1 mW of power consumption at 1.2 V supply voltage.     

Transimpedance amplifier with 120 dB dynamic range

A transimpedance amplifier (TIA) with compression of the input current is presented. The proposed TIA has two regions of operation: a linear one for small input currents and one with compression for high currents, which would otherwise saturate the TIA. The measured -3 dB bandwidth is 102 MHz, the equivalent RMS input current noise is 20.2 nA and the maximal current overdrive is 20.5 mA, leading to a dynamic range at the input of 120 dB     

12 Gb/s GaAs PHEMT跨阻抗前置放大器

采用0.5 μ m GaAs PHEMT工艺研制了一种单电源偏置光接收机跨阻抗前置放大器.放大器-3dB带宽约为9.5GHz;在50MHz~7.5GHz范围内,跨阻增益为43.5±1.5dB Ω ,输入输出回波损耗均小于-10dB;带内噪声系数在4dB~6.5dB之间,由此得到的最小等效输入噪声电流密度约为17.6pA/ Hz ;输入12Gb/s NRI伪随机序列时,放大器输出眼图清晰,眼开良好.     

40-GHz transimpedance amplifier with differential outputs using InP-InGaAs heterojunction bipolar transistors

High-gain and high-bandwidth transimpedance amplifiers (TIAs) are required for fiber-optic receiver modules. This paper reports on the design, fabrication, and characterization of a 40-Gb/s TIA for SONET/SDH STS-768/STM-256 applications based on an InP-InGaAs single heterojunction bipolar transistor (SHBT) process developed at Vitesse Semiconductor Corporation (Vitesse Indium Phosphide Release 1 or VIP-1). This amplifier consists of a single-ended input transimpedance pre-amplifier and a differential output post-amplifier. The measured differential transimpedance is 1800 /spl Omega/ with -3-dB bandwidth greater than 40 GHz. The high gain of this circuit eliminates the need for a standalone limiting amplifier between the conventional transimpedance pre-amplifier and the demultiplexer in short-reach applications.     

An InGaAs-InP HBT differential transimpedance amplifier with 47-GHz bandwidth

Return-to-zero differential phase-shift keying applications require a differential amplifier with high bandwidth, high gain, low noise, and good input impedance match. In this paper, we describe an InGaAs-InP heterostructure bipolar transistor differential transimpedance amplifier with high bandwidth of 47 GHz and high gain of 56 dB-/spl Omega/. The input-referred current noise is less than 35 pA//spl radic/Hz over the measurement range up to 40 GHz.     

A low-power 20-GHz 52-dB/spl Omega/ transimpedance amplifier in 80-nm CMOS

This paper describes the design of a transimpedance amplifier (TIA) for a low-power, short-distance, high-density fiber-optic interconnect communication system. The single-ended circuit has been designed in an 80-nm digital CMOS process and consumes only 2.2 mW from a 1-V supply. The measured results show a transimpedance gain of 52 dB/spl Omega/ and a large bandwidth of 20 GHz. This work presents the highest bandwidth at the lowest power consumption for CMOS transimpedance amplifiers reported to date.