Thick c-BN coatings - Preparation, properties and application tests

Due to the outstanding properties of cubic boron nitride (c-BN) - c-BN is the second hardest of all known materials, has a high wear resistance and a high thermal stability - this material is very promising for a broad range of applications, especially for cutting tools, both as bulk and as a coating material. The state-of-the-art is the use of sintered cutting inserts with c-BN grains. Such c-BN grains are synthesized in an expensive high-pressure-high-temperature process.The requirements for cutting tools continuously increase in production engineering and this leads to a strong demand for new super hard tool coatings. Cubic boron nitride coatings could be an attractive solution. Unfortunately, the preparation of thick c-BN coatings, on the μm scale, is difficult, due to some serious drawbacks and has been successful only in the last years for a few research groups worldwide.PVD processes allow the preparation of c-BN films thicker than 2 μm on silicon and 1 μm c-BN top layers on pre-coated cemented carbide cutting inserts. Measurements of mechanical properties like hardness and Young's modulus reveal that the properties of the c-BN coatings, with hardness of about 60 GPa, are nearly identical to those of c-BN bulk material.Results of systematic turning and milling tests of different coatings in combination with a c-BN top-layer on cemented carbide cutting inserts will be presented in detail. The new results confirm the high potential of c-BN coatings on cutting tools.     

铝基碳化硅精密铣削刀具磨损实验研究

针对铝基碳化硅切削加工中刀具易磨损、寿命低、切削难度大和加工成本高等问题,选用不同材料的硬质合金铣刀及金刚石铣刀进行切削加工实验,并利用扫描电镜和工具显微镜对高体积分数铝基碳化硅铣削时刀具磨损形态进行了分析研究.研究表明:硬质合金刀具前刀面和刃口磨损主要形式为粘结磨损和微崩刃,后刀面磨损主要为刻划磨损,而金刚石铣刀加工时刀具磨损很小;YG6X铣刀材料微观组织致密,抗磨损能力较强,宜粗加工时选用;金刚石刀体的硬度远大于SiC颗粒,且金刚石与工件的摩擦系数小,金刚石铣刀寿命远大于硬质合金铣刀,宜精加工时选用.     

Boron containing combination tool coatings—characterization and application tests

The requirements for durable tool coatings continuously increase. In many cases, tool coatings combining different phases or several layers could provide an improvement in tool life. The broad range of mechanical properties of materials in the B–C–N and Ti–B–N ternary systems, from very soft to superhard, presents many possibilities to generate various combination coatings. Such coatings were prepared using reactive sputter techniques with different target materials. An outstanding example is a superhard 3 μm thick coating system with a 0.5 to 0.8 μm thick cBN top layer deposited on cutting inserts. Soft coatings like hexagonal boron nitride were found to be essential for machining operations under dry conditions. The coatings were characterized with respect to hardness, abrasive wear rate and friction coefficients. The correlation between properties and composition was revealed. Application test results of B–C–N and Ti–B–N coating systems on tools obtained under near production conditions will be reported. Specifically, turning tests performed with cemented carbide cutting inserts coated with a superhard coating system with a cBN top layer will be discussed.     

Machining performance of low temperature treated P-30 tungsten carbide cutting tool inserts

Machining studies were conducted on C45 workpiece using both untreated and low temperature treated tungsten carbide cutting tool inserts. The machinability of the C45 steel workpiece is evaluated in terms of flank wear of the cutting tool inserts, main cutting force and surface finish of the machined workpieces. The flank wear of low temperature treated carbide tools is lower than that of untreated carbide tools on machining of C45 steel. The cutting forces during machining of C45 steel is lower with the low temperature treated carbide tools when compared with the untreated carbide tools. The surface finish produced on machining the C45 steel workpiece is better with the low temperature treated carbide tools when compared with the untreated carbide tools.     

Influence of Tool Coating,Tool Material,and Cutting Speed on the Machinability of Low-Leaded Brass Alloys in Turning

The influence of tool coating and material on the machinability of low-leaded brass alloys (Pb < 0.2%) was analyzed in external turning. Carbide tools with various coatings as well as polycrystalline diamond (PCD) tools were applied. As workpiece materials, three low-leaded brass alloys CuZn38As, CuZn42, and CuZn21Si3P were used. Their machining behavior was compared to the leaded (Pb < 3.32%) brass CuZn39Pb3. CuZn38As showed the worst machinability in terms of process forces, chip formation, and workpiece quality. This is due to the high volume fraction of α-phase with face-centered cubic lattice structure. The machining problems were reduced by the use of tool coatings, in particular by a diamond-like carbon coating. The latter is characterized by high hardness, diamond-like cubic-crystalline lattice structure, and low chemical affinity to brass, which reduced friction in the secondary shear zone. CuZn42 exhibited an improved machinability compared to CuZn38As due to the lower volume fraction of α-phase. The positive influence of the tool coating was similar to CuZn38As. Main machining problem of CuZn21Si3P is tool wear because of the hard silicon-rich κ-phase. In tool life tests, PCD showed higher performance than uncoated and coated carbide tools due to its high abrasive wear resistance and low adhesion tendency.     

Cost-effective way of hard turning with newly developed HSN2-coated tool

EN-31 (AISI 52100, hardness 55 HRC) is one of the difficult-to-cut steel alloys and it is commonly used in shafts and bearings. Nowadays, it is becoming a challenge to the cutting tool material for economical machining of extremely tough and hard steels. In general, CBN and PCBN tools are used for machining hardened steel. However, machining cost using these tools becomes higher due to high tool cost. For this purpose, carbide tool using selective coatings is the best substitute having comparable tool life, while its cost is approximately one-tenth of CBN tool. In this work, the newly developed second-generation TiAlxN super nitride (i.e., HSN²) is selected for PVD coating on carbide tool insert and further characterized using thermogravimetric analysis and differential scanning calorimetry for oxidation and thermal stability at high temperature. Later, HSN²-coated carbide inserts are successfully tested for their sustainability to expected tool life for turning of AISI 52100 steel. In the present study, forces, surface finish, and tool wear are used as a measure to appraise the performance of hard turning process. Experimentally, it is found that speed, feed rate, and depth of cut have considerable impact on forces, insert wear, and surface roughness of the machined surface.     

High-speed turning experiments on metal matrix composites

The hard abrasive ceramic component which increases the mechanical characteristics of metal matrix composites (MMC) causes quick wear and premature tool failure in the machining operations. The aim of the paper is to compare the behaviour of high rake angle carbide tools with their diamond coated versions in high-speed machining of an Al₂O₃Al 6061 MMC. The influence of the cutting parameters, in particular cutting feed and speed, on tool wear and surface finish has been investigated. The higher abrasion resistance of the coatings results in increased tool life performances and different chip formation mechanisms.     

Vibration-Assisted Precision Machining of Steel with PCD Tools

This article presents experimental results of precision machining of steel alloys with polycrystalline diamond tools. Ultrasonic vibration-assisted cutting was tried out for expanding the application of diamond tools for high-precision and high-quality machining of ferrous materials. The experimental results show that compared with conventional turning, the cutting performance, in terms of cutting force, surface finish, and tool life, was improved by applying ultrasonic vibration to the cutting tool. The cutting forces and tool wear measured in vibration cutting are much lower than those in conventional cutting. The tool wear mechanism was discussed on the basis of the observation of wear zone.     

Cutting Performance and Wear Mechanism of Multilayer Diamond-Coated Tools

Monolayer and multilayer diamond films are deposited on WC-Co cemented carbide by hot-filament chemical vapor deposition. The growth characteristics of diamond coatings are analyzed. Cutting performance characteristics such as tool life and the stability of machining process in the machining of presintered ZrO₂ are compared based on the variation of cutting speed and resultant cutting force, and workpiece surface roughness. For the monolayer diamond coatings, as the concentration of CH₄ increases from 1% to 5%, the diamond crystal is transformed from micron columnar crystal to nanocluster crystal. The multilayer diamond coatings combine the advantages of micron- and nanocrystalline structures. The multilayer diamond-coated tool exhibits longer service life and better machining quality. Because of the appearance of the brittle–plastic conversion mechanism, the surface integrity of ZrO₂ processed by multilayer diamond-coated tool is relatively high. As for the uncoated tool, the workpiece is mainly machined by brittle spalling. The interfacial stratified fracture system between the interlayers is proposed to be the toughening mechanism of the multilayer structure.     

Drehen und Fräsen pulvermetallurgischer Hartlegierungen für warmgehende Werkzeuge

Turning and Milling of Powder Metallurgical Hard Alloys for Tools in Hot Working Applications Hard metals are high wear resistant materials. The microstructure of these composites consists of hard phases which are embedded in a metal matrix. The high hardness and the high content of the hard phases lead to a difficult machining of these materials. The present study investigates the turning and milling of D3 cold work steel (X210 Cr 12) and the powder metallurgical Fe‐based alloys ASP60 and ASP23 + WC/W₂C. The cutting tool materials were polycrystalline cubic boron nitrides (CBN) and ceramic inserts. The machining process could be judged by means of tool wear and machining quality (surface roughness and changes in the surface near zone). The investigations illustrate that the machinability of the different hard metals depends on the cutting speed and the cutting tool material.     

Diamond and cBN hybrid and nanomodified cutting tools with enhanced performance: Development,testing and modelling

The potential of enhancement of superhard steel and cast iron cutting tool performance on the basis of microstuctural modifications of the tool materials is studied. Hybrid machining tools with mixed diamond and cBN grains, as well as machining tool with composite nanomodified metallic binder are developed, and tested experimentally and numerically. It is demonstrated that both combination of diamond and cBN (hybrid structure) and nanomodification of metallic binder (with hexagonal boron nitride/hBN platelets) lead to sufficient improvement of the cast iron machining performance. The superhard tools with 25% of diamond replaced by cBN grains demonstrate 20% increased performance as compared with pure diamond machining tools, and more than two times higher performance as compared with pure cBN tools. Further, cast iron machining efficiency of the wheels modified by hBN particles was 80% more efficient compared to the tool with the original binder. Computational model of hybrid superhard tools is developed, and applied to the analysis of structure-performance relationships of the tools.     

An Investigation on Turning Hardened Steel Using Different Tool Inserts

Turning of hard materials usually presents poor machinability. However, for high productivity, it is desirable to employ turning of hard materials rather than grinding. In this work, turning of hardened 16MnCrS5 steel with hardness of 43 HRC was explored to judge machining performance with plain and wide-groove-type chip-breaking TiC-coated carbide inserts under dry and wet environmental conditions, different cutting velocity, and feed. Tool wear tests were also done in dry and wet conditions. Satisfactory tool performance was observed under wet condition using TiC-coated plain and wide-groove carbide inserts even at 268 m/min cutting velocity, when dry machining could not be done effectively.     

Tool wear mechanisms in axial ultrasonic vibration assisted milling in-situ TiB2/7050Al metal matrix composites

The in-situ TiB₂ particle reinforced aluminum matrix composites are materials that are difficult to machine, owing to hard ceramic particles in the matrix. In the milling process, the polycrystalline diamond (PCD) tools are used for machining these materials instead of carbide cutting tools, which significantly increase the machining cost. In this study, ultrasonic vibration method was applied for milling in-situ TiB₂/7050Al metal matrix composites using a TiAlN coated carbide end milling tool. To completely understand the tool wear mechanism in ultrasonic-vibration assisted milling (UAM), the relative motion of the cutting tool and interaction of workpiecetool-chip contact interface was analyzed in detail. Additionally, a comparative experimental study with and without ultrasonic vibration was carried out to investigate the influences of ultrasonic vibration and cutting parameters on the cutting force, tool life and tool wear mechanism. The results show that the motion of the cutting tool relative to the chip changes periodically in the helical direction and the separation of tool and chip occurs in the transverse direction in one vibration period, in ultrasonic vibration assisted cutting. Large instantaneous acceleration can be obtained in axial ultrasonic vibration milling. The cutting force in axial direction is significantly reduced by 42%-57%, 40%-57% and 44%-54%, at different cutting speeds, feed rates and cutting depths, respectively, compared with that in conventional milling. Additionally, the tool life is prolonged approximately 2-5 times when the ultrasonic vibration method is applied. The tool wear pattern microcracks are only found in UAM. These might be of great importance for future research in order to understand the cutting mechanisms in UAM of in-situ TiB₂/7050Al metal matrix composites.The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-020-00294-2     

Correlation between edge radius of the cBN cutting tool and surface quality in hard turning

cBN cutting tools with superior mechanical properties are widely used in machining various hard materials. The microgeometry of cBN cutting tools, such as the edge radius, has great influence on the surface quality of components and tool life. For optimized tool geometry, it is crucial to understand the influence of the cBN cutting tool microgeometry on the machined surface quality. In this study, the attempt has been made to investigate the correlation between the cutting tool edge radius and surface quality in terms of the surface roughness and subsurface deformation through a FE simulation and experiment. Machining tests under different machining conditions were also conducted and the surface roughness and subsurface deformation were measured. Surface roughness and subsurface deformation were produced by the cutting tools with different edge radii under various cutting parameters. Both results from the FE simulation and machining tests confirmed that there was a significant influence on the surface quality in terms of both the surface roughness and subsurface quality from the edge radius. There is a critical edge radius ofcBN tools in hard turning in terms of surface quality generated.     

陶瓷刀具切削304不锈钢时的磨损性能

采用Ｓｉ３Ｎ４陶瓷刀具切削Ｔｉ基陶瓷，ＹＴ１５硬质合金和高速钢四种刀具对３０４奥氏体不锈钢进行了切削试验，比较各种刀具的耐磨性能，并且用ＳＥＭ，ＥＤＸ等对刀具的磨损表面进行分析。     

Study of deformation zone effects of low,conventional, high and very high speed machining

The paper deals with cutting speed in range 3 m?min^‐1 up to 2200 m?min^‐1 and its complex impact mainly on chip macroscopic shape, chip microstructure, chip compression, tool wear, tool life and machined surface quality and interprets and compares the effects regarding low, conventional, high and very high speed machining based on the dry turning of carbon steel by sintered carbide coated by titanium nitride and ceramic cutting inserts. The deformation zone response for different cutting speeds at the tool‐chip‐workpiece interfaces and their effect on tool wear were studied. The extensive (so called complete) experiments within wide range of values and large number of measurements were carried out. The formation of secondary chip occurring in high speed turning is reported. Moreover, the paper analyses the total machining time involving tool replacement time in terms of high speed machining regarding the obtained experimental results.     

A REVIEW OF THE CHEMICAL VAPOR DEPOSITION (CVD) OF THE REFRACTORY COMPOUNDS OF TITANIUM - A UNIQUE FAMILY OIF COATINGS

This paper is a review of a unique family of refractory compounds comprising the boride, carbide and nitride of titanium. These materials are characterized by high hardness, high wear resistance and chemical inertness. They are obtained as coatings by chemical vapor deposition (CVD) on a variety of substrates such as tool steel, cemented carbides, graphite and many others. Promising deposition techniques are plasma-CVD and metallo-organic CVD. Major applications of these coatings are found in wear, erosion and corrosion protection and in cutting tools     

Mathematical models to predict surface finish in fine turning of steel. Part II

This paper outlines further experimental development of mathematical models for predicting RMS surface finish in fine turning operation using TiC coated and cemented tungsten carbide throwaway cutting tools. The five independent variables included are: cutting speed, feed, depth of cut, time of cut of tool, nose radius. Using these five variables at different levels an experimental approach, predictive models for tungsten carbide and titanium coated tungsten carbide tools were developed. A sixth variable, 'the type of cutting tool,' was used to develop a single model for both the TiC coated and cemented carbide cutting tools. AIS1 4140 steel was used as workpiece specimen in the experimental work. Stepwise regression analysis was used in developing the models.     

Chemical vapour deposition (CVD) diamond coated tools performance in machining of PEEK composites

This paper presents a study about the chemical vapour deposition (CVD) diamond coated tool performance in machining unreinforced PEEK and composite PEEK CF30 (reinforced with 30% of carbon fibres).

The experimental procedure consisted of turning operations, during which cutting forces and surface roughness obtained in composite workpieces were measured.

The obtained results showed a best cutting performance for CVD diamond coated tool in machining PEEK composites, particularly in terms of cutting forces and power consumption, when compared with polycrystalline diamond (PCD) and cemented carbide (K10) cutting tools. This fact is very important due to the minor production costs of CVD diamond coated tools in comparison with PCD tools.     

Wear monitoring of single point cutting tool using acoustic emission techniques

This paper examines the flank and crater wear characteristics of coated carbide tool inserts during dry turning of steel workpieces. A brief review of tool wear mechanisms is presented together with new evidence showing that wear of the TiC layer on both flank and rake faces is dominated by discrete plastic deformation, which causes the coating to be worn through to the underlying carbide substrate when machining at high cutting speeds and feed rates. Wear also occurs as a result of abrasion, as well as cracking and attrition, with the latter leading to the wearing through the coating on the rake face under low speed conditions. When moderate speeds and feeds are used, the coating remains intact throughout the duration of testing. Wear mechanism maps linking the observed wear mechanisms to machining conditions are presented for the first time. These maps demonstrate clearly that transitions from one dominant wear mechanism to another may be related to variations in measured tool wear rates. Comparisons of the present wear maps with similar maps for uncoated carbide tools show that TiC coatings dramatically expand the range of machining conditions under which acceptable rates of tool wear might be experienced. However, the extent of improvement brought about by the coatings depends strongly on the cutting conditions, with the greatest benefits being seen at higher cutting speeds and feed rates. Among these methods, tool condition monitoring using Acoustic Techniques (AET) is an emerging one. Hence, the present work was carried out to study the stability, applicability and relative sensitivity of AET in tool condition monitoring in turning.