A silicon‐chip‐based light valve with reflective twisted‐nematic mode for high‐definition projectors

Crystalline‐silicon‐chip‐based reflective light valves are suitable for realizing high definition and bright liquid‐crystal projectors. We have developed an XGA (1025 × 769 pixels) silicon‐chip‐based light valve with a diagonal display area of 2.54 cm (1 in.). The reflective twisted‐nematic mode was examined by using the Jones matrix method as a display mode, and the normally white reflective twisted‐nematic mode was selected. This mode is suitable for a narrow cell gap, and a fast response time can be expected. In addition, the driving voltage of this mode is low and has good chromaticity with small retardation. The cell gap of the light valve is 2 μm. The cell gap support is made using spacer posts formed on the silicon chip with a photodefinable resin. The response time is 12 msec, including both rise and fall times. The contrast ratio is more than 1000 at 5 Vrms.     

Photoalignment and photo‐patterning of planar and homeotropic liquid‐crystal‐display configurations

Abstract— Optical alignment and micro‐patterning of the alignment of liquid‐crystal displays (LCDs) by linear photopolymerization (LPP) technology renders high‐quality multi‐domain twisted‐nematic (TN) and supertwisted‐nematic (STN) displays with broad fields of view over wide temperature ranges feasible. The prerequisites are the generation of photo‐induced high‐resolution azimuthal alignment patterns with defined bias‐tilt angles 0° ≤ θ ≤ 90°. For the first time, LPP‐aligned single‐ and dual‐domain vertically aligned nematic LCDs (VAN‐LCDs) are presented. Dual‐domain VAN‐LCDs are shown to exhibit broad fields of view which are further broadened by combining the displays with LPP‐aligned optical compensators made of liquid‐crystal polymers.     

Application of re‐crystallized metal‐induced unilaterally crystallized polycrystalline‐silicon thin‐film‐transistor technology to reflective liquid‐crystaldisplay

Single‐polarizer reflective twisted‐nematic (RTN) liquid‐crystal modes offer larger viewing angles, higher contrast ratios and lower power dissipation compared to regular double‐polarizer transmissive‐ reflective liquid‐crystal implementations. The application of re‐crystallized metal‐induced unilaterally crystallized polycrystalline‐silicon thin‐film‐transistor (TFT) technology to realize active matrices and peripheral circuit components for hand‐held direct‐view RTN‐mode video displays is reported.     

Single‐cell‐gap transflective liquid‐crystal display using double‐ and single‐mode approaches

Abstract— In this paper, many popular methods to study transflective liquid‐crystal‐displays (LCDs) have been discussed, and several new transflective LCD configurations with a single‐cell gap have been proposed. The traditional double‐cell‐gap method gives the best match of the transmittance/reflectance voltage curve (TVC/RVC) and also the widest viewing angle, but also brings the highest fabrication complexity. The single‐cell‐gap transflective LCD is much easier to fabricate and also shows a good match of TVC/RVC. A new methodology has been shown to find optimal configurations for single‐cell‐gap transflective LCDs. New configurations using multimode in a single pixel include twisted nematic (TN) optically compensated bend (OCB), TN electrically controlled birefringence (ECB), and TN low‐twisted nematic (LTN). TN and hybrid‐aligned nematic (HAN) modes have been investigated for single‐mode transflective LCDs. The results exhibit high contrast ratio, a good match of TVC/RVC, as well as wide viewing angle.     

Active‐matrix and flexible liquid‐crystal displays with carbon‐nanotube pixel electrodes

Abstract— The necessary processes to use random carbon‐nanotube networks as transparent conductors in twisted‐nematic liquid‐crystal displays have been developed, replacing indium tin oxide. Because the nanotubes are deposited vacuum‐free from suspension, the potential advantages are lower costs for material, equipment, and production. Nanotube networks are also much better suited for flexible displays than the commonly used metal oxides. With the developed processes, the world's first full‐color active‐matrix LCDs as well as directly addressed flexible displays on plastic substrates with carbon‐nanotube pixel electrodes, have been realized.     

Local dimming light‐guiding plate type backlight system using alignment‐controlled polymer‐dispersed liquid crystals

A new technology which enables a local brightness control according to the displayed images has been expected in the thin and lightweight backlight systems to improve a contrast ratio and power consumption of the liquid crystal displays (LCDs). In this paper, we have proposed a novel local‐dimming backlight system using alignment‐controlled polymer‐dispersed liquid crystals as a light‐guiding plate and investigated the forming conditions of polymer‐dispersed liquid crystals to achieve both a high‐luminance ratio and a fast response speed. As a result, we found that a luminance ratio and response speed of the backlight system can be improved by using bifunctional LC monomer materials and forming fine and rigid polymer network in the LCs, and achieved high luminance ratio of 16:1 and fast response time less than 0.5 ms. In addition, we fabricated the twisted nematic‐mode LCD using the local dimming light‐guiding plate‐type backlight based on this design, and successfully realized eight times higher contrast ratio than that of the traditional twisted nematic‐mode LCD.     

Supertwisted nematic liquid crystal displays

The rapid development of supertwisted nematic liquid crystal displays since their invention in 1982 has opened up a wide range of potential applications for complex high-information-content liquid crystal displays. Monochrome, A4 sized, 640 × 400 pixel supertwisted nematic displays are now available commercially with a performance superior to twisted nematic displays. Development of the supertwisted nematic display is reviewd and the physical principles involved in its operation are described.     

Electro-optical properties of a twisted hybrid aligned nematic mode for reflective liquid crystal displays

Abstract— A twisted hybrid aligned (THA) mode is proposed for reflective liquid-crystal displays. In the reflective configuration, a single polarizer and a reflective electrode are used to achieve electrooptical switching between the black and white states in the THA mode of a chiral nematic liquid crystal. Numerical simulations are performed to optimize the cell parameters such as the cell thickness and the amount of the twist in the hybrid geometry. The reflective THA mode is found to give wider viewing and faster response characteristics than a twisted nematic one. The role of an optical retardation film on device performance of such a reflective THA cell is also discussed.     

Design of a dual‐f‐number illumination system and its application to DMD™ projection displays

Abstract— A dual‐f/# optical system is evaluated and considered for illumination. Étendue theory has been employed to increase the optical throughput and collection efficiency. A classical Cooke triplet with a dual f/# is included for illustration. As a demonstration of the potential application to projection displays, an elliptically shaped illumination‐pupil system is proposed to increase the optical collection efficiency in the DMD? (Digital Micromirror Device?)‐based projection system. With a dual‐f/# configuration, this design can eliminate the f/2.4 constraint that was caused by the light‐steering action of the narrow ±12° tilt angles on the DMD?. The percentage of increase in the optical collection efficiency is 6.2% in the dual f/2.0 × f/2.4 optical projection system by using ray‐tracing simulation. This method enables a lower than f/2.4 optical design with a high brightness and an adequate contrast ratio in the DMD?‐based projectors.     

Molecular design for stabilizing a blue phase III and electro‐optical switching in the blue phase

Abstract— The molecular design of a liquid crystal to stabilize a blue phase III (BPIII) is reviewed, and the electro‐optical switching with a response time on the order of 10^?2 sec for BPIII exhibited by a novel chiral liquid crystal is reported. Binaphthyl derivatives and T‐shaped compounds are presented, and the structure‐property correlations of the chiral compounds are discussed. Two origins of the twisting power of the compounds, i.e., their inherent molecular chirality and the chirality‐induced twist conformation, play an important role in the appearance of the BPIII. Furthermore, BPIII was also induced in some binary mixtures of a host nematic liquid‐crystal possessing molecular biaxiality and a conventional chiral compound. The electro‐optical switching in the BPIII is attributed to an electric‐field‐induced phase transition between the BPIII and nematic (N) phases. BPIII is on the microscopically twisted nematic order, but is macroscopically isotropic. Therefore, the present technology can offer a pronounced black state in the BPIII without surface treatment and a homogeneous bright state in the induced N phase.     

A compact monopolar patch antenna with bandwidth‐enhancement under dual‐mode resonance

A compact monopolar microstrip patch antenna (MPA) with enhanced‐bandwidth is proposed. In order to achieve the miniaturized patch, the zeroth‐order mode of the MPA instead of its higher‐order modes is employed at first by loading the shorting pin around the center of the patch. After that, a L‐shaped microstrip line with a shorting pin is introduced at the periphery of the patch radiator to excite an additional non‐radiative mode for bandwidth enhancement. In final, the proposed MPA is fabricated and measured. The results illustrate that the antenna generates an enhanced‐bandwidth of about 4.1% ranging from 2.39 to 2.49 GHz, which is significantly larger than that of the traditional MPA around 1%. Meanwhile, the dimensions of the radiating patch are obviously decreased down due to the employment of zeroth‐order mode, which are kept as small as about 0.17 λ₀ × 0.22 λ₀ × 0.026 λ₀ (λ₀ is the free‐space wavelength).     

Prototype TM01 mode launcher by using Pagoda‐shaped geometry in circular waveguide for microwave plasma interaction experiments at SYMPLE

SY stem for M icrowave PL asma E xperiments (SYMPLE) is an experimental system to investigate the physics of linear and nonlinear interaction of high‐power microwave (HPM) with plasma in the Institute for Plasma Research (IPR), Gandhinagar, India. The objective of this paper was to present the designing and development of coaxial TEM to TM₀₁ mode launcher in the circular waveguide for microwave plasma interaction experiments at SYMPLE. TEM mode was converted into TM₀₁ mode by using aluminum made circular Pagoda‐shaped geometry. TM₀₁ mode launcher was hence successfully designed and developed. 3D full‐wave electromagnetic solver was used to analyze and optimize the outcomes. The proposed configuration of mode launcher achieved the bandwidth of 658 MHz for S₁₁ < ?10 dB. The maximum value of achieved return loss was ~40 dB while insertion loss was ~0 dB at 3 GHz, which verified the ~100% transmission of power without any reflections. Mode purity was also verified by field distribution in the circular waveguide.     

Amorphous‐silicon thin‐film transistors made at 280°C on clear‐plastic substrates by interfacial stress engineering

Abstract— A process temperature of ～300°C produces amorphous‐silicon (a‐Si) thin‐film transistors (TFTs) with the best performance and long‐term stability. Clear organic polymers (plastics) are the most versatile substrate materials for flexible displays. However, clear plastics with a glass‐transition temperature (T_g) in excess of 300°C can have coefficients of thermal expansion (CTE) much larger than that of the silicon nitride (SiN^x) and a‐Si in TFTs deposited by plasma‐enhanced chemical vapor deposition (PECVD). The difference in the CTE that may lead to cracking of the device films can limit the process temperature to well below that of the T_g of the plastic. A model of the mechanical interaction of the TFT stack and the plastic substrate, which provides design guidelines for avoid cracking during TFT fabrication, is presented. The fracture point is determined by a critical interfacial stress. The model was used to successfully fabricate a‐Si TFTs on novel clear‐plastic substrates with a maximum process temperature of up to 280°C. The TFTs made at high temperatures have higher mobility, lower leakage current, and higher stability than TFTs made on conventional low‐T_g clear‐plastic substrates.     

Passively addressed FLC display possessing an inherent gray scale and memory

Abstract— A passively addressed 64 × 64 ferroelectric liquid‐crystal display (FLCD) has been developed. The display matrix has a 33 × 33 mm² aperture, and the FLC layer thickness is 5.2 ± 0.2 μm. The display device operates with a frame frequency of 30 Hz (at V_row = ±18 V, V_col = ±9 V, T = 23°C), generating a continuous gray scale which can be memorized for more than 10 days after the driving voltage is switched off. A new approach for multiplex electronic addressing of the FLCD gray scale is proposed. The conditions of the hysteresis‐free gray‐scale generation for multiplex addressing and the gray‐scale memorization after the voltage is switched off, as well as the time steadiness of memorized images, are considered.     

Maximizing electro‐optic performances in the fringe‐field switching liquid crystal mode with negative dielectric anisotropic liquid crystal

The fringe‐field switching (FFS) mode that uses liquid crystals (LCs) with negative dielectric anisotropy is used in high‐resolution FFS liquid crystal display owing to its higher transmittance over positive LC, although its response time becomes slow and operating voltage (V_op) becomes high. In the device, reduction of the cell gap is required to achieve fast response time, which results in increase in V_op in general. In this paper, we propose the FFS mode with electrode width 1 µm and distance between the electrodes 1.5 µm. In such an electrode structure, V_op decreases with decreasing cell gap to 2 µm so that a proper V_op, high LC's light efficiency of 90%, a high color temperature, and a fast response time less than 10 ms, can be achieved, which maximizes electro‐optic performance of the FFS mode.     

Improved image quality of a high‐transflective tRGB‐t/rW TFT‐LCD

Abstract— This work combines a very simple resolution rescaling method, a well‐known RGB‐to‐YUV converting technique and a detection strategy into an optimized switchable mechanism in order to eliminate the problems of obvious zigzag profiles caused by the special layouts of transflective tRGB‐t/rW TFT‐LCDs and the poor reflective gray‐level contrast ratio effected by the minimum white data in the transmissive RGB‐W + subpixel rendering algorithms. Finally, a transflective tRGB‐t/rW TFT‐LCD is revealed not only to have no visible zigzag profiles and high visibility of reflective gray‐level contrast ratio, but also to have extreme reflectance and transmittance. The excellent optical performance of the proposed system makes it particularly suitable for single‐panel applications that need both high‐transmissive main displays and high‐reflective subdisplays.     

Dual‐band balanced coupler with wideband common‐mode suppression

A novel compact dual‐band balanced coupler with differential‐mode power division, broadband common‐mode, and common‐to‐differential‐mode conversion suppression is proposed. In these double‐functionality balanced‐coupler architectures, double‐sided parallel‐strip line 180° phase inverters are used to realize the broadband common‐mode rejection. Moreover, the frequency is tunable by changing the characteristic impedance of the transmission line. For practical verification, a balanced couplers (ε_r = 2.65, h = 0.5 mm, tan(δ_D) = 0.003) operation at 0.9/1.8 GHz is constructed in microstrip technology and tested.     

Time‐varying filter design for semi‐Markov jump linear systems with intermittent transmission

This paper focuses on the filter design problem for semi‐Markov jump linear systems. The system outputs are transmitted to the filter via networks, and it is assumed that the transmission is imperfect with data packet dropouts subject to the Bernoulli random binary distribution. A σ‐error mean square stability criterion is first derived for the underlying systems. On the basis of the criterion, the H_∞ performance analysis is conducted. By constructing a time‐varying Lyapunov function, a time‐varying H_∞ filter scheme is investigated. Because the presented approach can cover the mode‐dependent and mode‐independent time‐invariant H_∞ filter schemes as special cases, the conservatism of the derived results is less than those of the time‐invariant filter schemes. An active suspension system with activator uncertainties is lastly presented to illustrate the effectiveness and feasibility of the derived theoretical results. Copyright © 2017 John Wiley & Sons, Ltd.     

A photographic technique for assessing the viewing‐angle performance of liquid‐crystal displays

Abstract— Liquid‐crystal displays (LCDs) have notable variation in luminance and perceived contrast as a function of the angle from which they are viewed. Though this is an important performance issue for LCDs, most evaluation techniques for assessing this variation have been limited to laboratory settings. This study demonstrates the use of a photographic technique for such an evaluation. The technique is based on an actively cooled charge‐coupled‐device (CCD) detector in combination with a macro lens covering a circular angular range (θ) of ±42.5°. The camera was used to evaluate the luminance and perceived contrast properties of an LCD. Uniform field images corresponding to 17 equally spaced gray‐scale values in the digital driving level (DDL) range of the display system were acquired. The 12‐bit gray‐scale digital images produced by the camera were converted to luminance units (cd/m²) via the measured luminance vs. DDL response function of the camera. The changes in perceived contrast as a function of viewing angle were derived from the Barten model of the gray‐scale response of the human‐visual system using the methods proposed by the AAPM TG18 Report. The results of this photographic technique were compared to measurements acquired from a similar display using a Fourier‐optics‐based luminance meter. The results of the two methods generally agreed to within 5%. The photographic methods used were found to be accurate and robust for in‐field assessment of the angular response of LCDs over the FOV of the camera.     

Liquid‐crystal displays using printed plastic TFT backplanes

Abstract— In this paper, we present results from a new liquid crystal over plastic printed thin‐film‐transistor (TFT) display. The display demonstrator shows that the processing incompatibilities between the plastic TFT backplane and the liquid‐crystal materials can be addressed to make a stable twisted‐nematic structure. New fabrication processes such as the photo‐alignment of liquid crystals have made it possible to create a new generation of displays, which pave the way towards fully integrated plastic liquid‐crystal‐display technologies.