AlGaN/AlN/GaN肖特基二极管的电学性能

利用金属有机化学气相淀积(MOCVD)方法生长的AlGaN/AlN/GaN/蓝宝石材料制备了AlGaN肖特基二极管.器件的肖特基接触和欧姆接触分别为Ti/Pt和Ti/Al/Ti/Au,均采用电子束蒸发的方法沉积.AlGaN表面欧姆接触的比接触电阻率为7.48×10-4Ω/cm2,器件的I-V测试表明该AlGaN肖特基二极管具有较好的整流特性.根据器件的正向,I-V特性计算得到器件的势垒高度和理想因子分别为0.57eV和4.83.将器件在300℃中温退火,器件的电学性能有所改善.     

AlGaN/AlN/GaN肖特基二极管的电学性能

利用金属有机化学气相淀积(MOCVD)方法生长的AlGaN/AlN/GaN/蓝宝石材料制备了AlGaN肖特基二极管.器件的肖特基接触和欧姆接触分别为Ti/Pt和Ti/Al/Ti/Au,均采用电子束蒸发的方法沉积.AlGaN表面欧姆接触的比接触电阻率为7.48×10-4Ω/cm2,器件的I-V测试表明该AlGaN肖特基二极管具有较好的整流特性.根据器件的正向,I-V特性计算得到器件的势垒高度和理想因子分别为0.57eV和4.83.将器件在300℃中温退火,器件的电学性能有所改善.     

不同退火温度对4H SiC 金半接触的影响

采用高真空电子束蒸发法制作了基于4H SiC外延材料的肖特基二极管,其中欧姆接触材料为Ti/Ni,肖特基接触材料为Ni。常温下,电流-电压(I-V)测试表明Ni/4H SiC肖特基二极管具有良好的整流特性,热电子发射是其主要输运机理。对比分析不同快速退火温度下器件的I-V特性,实验结果表明875 ℃退火温度下欧姆接触特性最好,400 ℃退火温度下器件肖特基接触I-V特性最好,理想因子为1.447,肖特基势垒高度为1.029 eV。     

ICP刻蚀损伤对n-GaN-Ni/Au肖特基接触特性的影响

通过电流-电压法(I-V),电容-电压法(C-V)对n-GaN材料的ICP(感应耦合等离子体)刻蚀样品和未刻蚀样品上的肖特基势垒二极管的电学特性进行了分析.利用原子力显微镜(AFM)和扫描电镜(SEM)对刻蚀样品的表面形貌,以及退火前后肖特基接触金属的表面形貌变化进行了研究.试验表明,ICP刻蚀会在GaN表面引入损伤,形成电子陷阱能级从而引起肖特基二极管的势垒高度降低,理想因子增大,反向泄漏电流增大.刻蚀样品在400 ℃热退火可以恢复二极管的电特性,退火温度到600 ℃时二极管特性要好于未刻蚀的样品.     

退火对Pt/TiO2肖特基二极管结构及电学性能的影响

以硅为衬底,采用射频磁控溅射技术制备了TiO2薄膜,利用扫描电子显微镜及拉曼光谱对退火前后的TiO2进行表征与结构分析.结果表明,退火后的TiO2具有良好的结晶特性,且呈锐钛矿结构.在此薄膜工艺条件下,以TiO2为半导体层在玻璃基底上制备了Al/TiO2/Pt肖特基二极管,并在153～433 K温度范围内对其进行了I-V测试,得到以下结果:在整个温度范围内,A1/TiO2/Pt肖特基二极管均表现出良好的整流特性;其理想因子随温度升高而降低,势垒高度随温度升高而升高;在433 K下,理想因子为1.31,势垒高度为0.73,表明此肖特基二极管已接近理想的肖特基二极管.     

ZrN/n-GaAs肖特基势垒特性研究

本文用RBS,AES和电特性测量等方法,研究了ZrN/n-GaAs肖特基势垒.结果表明ZrN/GaAs势垒有良好的电特性和高温稳定性.经850℃高温退火后,势垒高度为0.90eV,理想因子n=1.02.同时我们观察到,随着退火温度升高(从500℃升高到850℃),ZrN/GaAs势垒电特性有明显改进:肖特基势垒高度增大、二极管反向电流减小、二极管电容减小和反向击穿电压增大.以上特点表明,ZrN/GaAs是用于自对准高速GaAs集成电路的较为理想的栅材料.     

CoSi_2/n—Si肖特基势垒的形成和特性

本文利用XRD、RBS、AES和四探针等方法研究了不同温度快速热退火后的Co/Si结构薄膜固相反应形成钴硅化物的相序、组份和电学特性。并报道了性能优越的CoSi_2/n-Si肖特基二极管的特性,其势垒高度为0.66eV,理想因子为1.01。     

Ni，Ti/4H-SiC肖特基势垒二极管

采用本实验室生长的4H-SiC外延片,分别用高真空电子束蒸Ni和Ti做肖特基接触金属,Ni合金作欧姆接触,SiO_2绝缘环隔离减小高压电场集边效应等技术,制作出4H-SiC肖特基势垒二极管(SBD)。该器件在室温下反向击穿电压大于600 V,对应的漏电流为2.00×10~(-6)A。对实验结果分析显示,采用Ni和Ti作肖特基势垒的器件的理想因子分别为1.18和1.52,肖特基势垒高度为1.54 eV和1.00 eV。实验表明,该器件具有较好的正向整流特性。     

离子束刻蚀HgCdTe环孔pn结Ⅰ-Ⅴ、RD-Ⅴ特性的研究(下)

本文推导了一种可简便,准确、直观计算和分析pn结Ⅰ-Ⅴ特性的公式和方法,并应用该方法对两类典型HgCdTe环孔pn结的Ⅰ-Ⅴ、RD-Ⅴ特性进行了计算和拟合;得到了表面欧姆(反型沟道)漏电导、二极管理想因子n随电压的分布等反映二极管结特性的重要参数.计算结果表明,对于长波HgCdTe光伏器件而言,表面漏电流在整个暗电流中所占的比重相当大,表面漏电流严重地制约着器件性能.HgCdTe材料的晶体缺陷会使二极管的理想因子n增大,从而使产生-复合电流及陷阱辅助隧穿电流增加.     

离子束刻蚀HgCdTe环孔pn结I—V、RD—V特性的研究（上）

本文推导了一种可简便、准确、直观计算和分析pn结I-V特性的公式和方法,并应用该方法对两类典型HgCdTe环孔pn结的I-V、RD-V特性进行了计算和拟合;得到了表面欧姆(反型沟道)漏电导、二极管理想因子n随电压的分布等反映二极管结特性的重要参数.计算结果表明,对于长波HgCdTe光伏器件而言,表面漏电流在整个暗电流中所占的比重相当大,表面漏电流严重地制约着器件性能.HgCdTe材料的晶体缺陷会使二极管的理想因子n增大,从而使产生-复合电流及陷阱辅助隧穿电流增加.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.