用MOCVD方法在GaAs衬底上低温生长ZnO薄膜

采用二乙基锌(DEZn)和水(H2O)作为生长源,利用金属有机化学气相沉积(MOCVD)的方法,在100～400℃低温范围内,在GaAs(001)衬底上制备了ZnO薄膜.利用X射线衍射(XRD),室温PL,AFM,SEM研究了薄膜的晶体结构特性、发光特性及表面形貌特性.XRD分析表明ZnO薄膜具有很强的c轴取向,(002)峰的FWHM平均值为0.3°.当生长温度达到400℃时从SEM测量结果可以观察到薄膜表面呈六角状结晶.随着生长温度的升高,薄膜的晶粒尺寸变大,结晶质量得到提高但同时表面变粗糙.室温PL测量显示薄膜在370nm附近有强的近带边发射,没有观测到深能级发射峰.     

用MOCVD方法在GaAs衬底上低温生长ZnO薄膜

采用二乙基锌(DEZn)和水(H2O)作为生长源,利用金属有机化学气相沉积(MOCVD)的方法,在100～400℃低温范围内,在GaAs(001)衬底上制备了ZnO薄膜.利用X射线衍射(XRD),室温PL,AFM,SEM研究了薄膜的晶体结构特性、发光特性及表面形貌特性.XRD分析表明ZnO薄膜具有很强的c轴取向,(002)峰的FWHM平均值为0.3°.当生长温度达到400℃时从SEM测量结果可以观察到薄膜表面呈六角状结晶.随着生长温度的升高,薄膜的晶粒尺寸变大,结晶质量得到提高但同时表面变粗糙.室温PL测量显示薄膜在370nm附近有强的近带边发射,没有观测到深能级发射峰.     

射频磁控溅射制备Mn掺杂ZnO薄膜的结构和铁磁性能研究

采用射频磁控溅射法制备了Mn掺杂ZnO(Zn1-x Mnx O,其中x=0,0.03,0.06)薄膜.通过X射线衍射(XRD)、拉曼光谱(Raman)、原子力显微镜(AFM)和超导量子干涉磁强计(SQUID)对薄膜结构和磁性能进行了研究.XRD和Raman研究表明,不同浓度Mn掺杂ZnO薄膜均为ZnO的六角纤锌矿结构,...     

Cd掺杂ZnO薄膜的光致发光性能研究

三元半导体Cd掺杂ZnO薄膜通过脉冲激光法沉积 在石英玻璃基底上,Gd含量x从0增加到0.23。X射线衍射(XRD)图谱表明,所有Zn1－xCd xO薄膜都具有c轴取向的六方纤锌矿结构,而且c轴 晶格常数随着 x的增加而增加。原子力显微镜(AFM)观察到,随着x的增加,Zn1－xCdxO 薄膜的晶粒尺寸逐渐减小。光致发光(PL)和透过率 测量都证实,随着x的增加,薄膜的禁带宽度Eg从3.27eV降低到了2.78eV,同时导致了PL峰半高 宽(FWHM)的变大。PL峰迁移到了可见光范围内,使得Zn1－xCdxO薄膜可以应用在可见光发光二极管及其它高效率的光电 子器件。     

在不同衬底上生长ZnO薄膜及其特性研究

在不同衬底温度下用脉冲激光沉积法(PLD)分别在n-Si(111)、蓝宝石(001)和非晶石英衬底上生长了ZnO薄膜。首先对薄膜进行了X射线衍射(XRD)分析,找出在三种不同衬底上制得的结晶质量最好的ZnO薄膜所对应的最佳衬底温度。然后对最佳衬底温度下得到的ZnO薄膜分别进行了X射线衍射(XRD)、光致发光谱(PL)和原子力显微镜(AFM)分析。结果表明,在硅衬底上生长的ZnO薄膜XRD谱半高宽最小,PL谱特征发光峰强度最强,AFM下的平均粒径最大,说明硅衬底上生长的ZnO薄膜结晶质量最好,而在石英衬底上生长的ZnO薄膜结晶质量最差。     

退火对MOCVD法生长ZnO薄膜性能的影响

采用MOCVD方法在(001)Si衬底上生长ZnO薄膜,并在空气中800℃退火1 h.生长及退火样品的XRD图谱均显示了较强的(002)ZnO衍射峰,表明ZnO薄膜为c轴高取向生长.光电子能谱(XPS)分析显示,退火后ZnO薄膜从富Zn生长变为富O生长.在样品的室温PL 谱中,观察到未退火样品的紫外发射峰的中心为3.28 eV,并观察到退火样品位于3.30 eV的自由激子发射峰和位于3.23 eV的施主-受主对的复合发光峰.实验结果表明,退火后ZnO薄膜的晶体质量得到提高.     

PLD法生长硅基ZnO薄膜的特性

用脉冲激光沉积法(PLD)在n型硅(111)平面上生长ZnO薄膜。XRD在2θ为34°处出现了唯一的衍射峰,半高宽仅0.85°;傅里叶红外吸收(FTIR)在413.08cm–1附近出现了对应Zn—O键的红外光谱的特征吸收峰;光致发光(PL)测量发现了位于330,368,417和467nm处的室温光致发光峰;SEM和TEM显示了薄膜的表面形貌以及结晶程度。ZnO单晶薄膜具有c轴取向高度一致的六方纤锌矿结构。     

Research on Acceptor Nature of the N : ZnO Thin Films

使用溶胶-凝胶法制备N:ZnO薄膜,用X射线衍射仪(XRD)对晶体结构进行表征,用扫描电子显微镜(SEM)观察薄膜表面形貌,用荧光光谱仪测量低温(8 K)及变温条件(8～200 K)下的光致发光(PL)光谱.分析了各个发射峰的形成机理,通过薄膜缺陷态发光和受主能级的关联性,计算出了N作为受主所需电离能的大小在0.255～0.31 eV范围内.研究结果为以后P型ZnO薄膜的制备和研究提供了依据.     

900℃空气退火对L-MBE生长的ZnO薄膜发光特性的影响

采用激光分子束外延法在蓝宝石衬底(0001)上生长了高度c轴择优取向的高质量ZnO薄膜,在空气中对生长的薄膜进行900℃退火处理,并对退火前后样品的结晶质量、发光特性采用X射线衍射(XRD)、变温光致发光(PL)研究.退火处理后的ZnO薄膜(0002)面XRDθ-2θ扫描曲线强度明显增强.在光致发光实验中,观测到薄膜分别在3.352,3.309和3.237eV附近有3个明显的近紫外发光峰,分别对应自由激子发射、中性施主或受主束缚激子I9及其声子伴线1Lo.随着温度升高,峰位逐渐向长波方向移动(即所谓"红移"),半高宽(FWHM)逐渐展宽;在发光谱中,来自于晶体缺陷的深能级(DL)区发光强度极小.     

退火对Al掺杂ZnO薄膜材料结构性能和表面形貌的影响研究

采用无机盐溶胶-凝胶方法在载玻片衬底上制备了ZnO:Al薄膜,利用X射线衍射(XRD)和原子力显微镜(AFM)研究了退火温度和退火时间对ZnO:Al薄膜结构和形貌的影响.结果显示,ZnO:Al薄膜为六角纤锌矿晶体结构,具有很高的沿C轴的(002)择优取向,随退火温度的升高或退火时间的适当延长,衍射峰的半高宽减小、强度增强,晶粒尺寸增大.结果表明,通过适当控制退火温度和退火时间可以得到高质量的ZnO:Al薄膜.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.