The System Al2O3-Cr2O3-Sio2

Liquidus phase equilibrium data are presented for the system Al₂O₃-Cr₂O₃-SiO₂. The liquidus diagram is dominated by a large, high-temperature, two-liquid region overlying the primary phase field of corundum solid solution. Other important features are a narrow field for mullite solid solution, a very small cristobalite field, and a ternary eutectic at 1580°C. The eutectic liquid (6Al₂O₃-ICr₂O₃-93SiO₂) coexists with a mullite solid solution (61Al₂O₃-10Cr₂O₃-29SiO₂), a corundum solid solution (19Al₂O₃-81Cr₂O₃), and cristobalite (SO₂). Diagrams are presented to show courses of fractional crystallization, courses of equilibrium crystallization, and phase relations on isothermal planes at 1800°, 1700°, and 1575°C. Tie lines were sketched to indicate the composition of coexisting mullite and corundum solid solution phases.     

Cone Deformation Study of a Portion of the System SrO–Al2O3–SiO2

The results of a study of deformation temperatures and rates within the composition area 25 to 45% SrO, 5 to 25% Al₂O₃, 50 to 70% SiO₂ are presented. A eutectic of the composition 30% SrO, 10% Al₂O₃, 60% SiO₂ is indicated with "1 o'clock" deformation at 1155°C. and "6 o'clock" deformation at 1165°C. A low-temperature area surrounding this eutectic includes 27.5 to 32.5% SrO, 10 to 12.5% Al₂O₃, 57.5 to 62.5% SiO₂. Compositions within this range reach "6 o'clock" deformation at approximately 1180°C.     

Densities of SiO2-Al2O3 Melts

The densities of binary aluminosilicate melts were measured X-radiographically as a function of Al₂O₃, concentration between 1800° and 2000°C. Within this temperature range, the density curves vary linearly and are parallel from fused SiO₂ to ≊30 to 45 mol% Al₂O₃, depending on the temperature. At higher Al₂O₃ contents, negative deviation from linearity increases with increasing temperature. Recent supplementary research efforts on various aspects of the system SiO₂-Al₂O₃ indicate that the changing coordination and structural role of the aluminum ion may be a primary factor in determining the shapes of the density curves.     

Revised Phase Diagram for the System Al2O3—SiO2

On the basis of 190 runs made up to 1860°C in sealed noble-metal containers the following revisions have been made in the equilibrium diagram for the system A1₂O₃–SiO₂. Mullite melts congruently at 1850°C. The extent of equilibrium solid solution in mullite at solidus temperature is from approximately 60 mole % Al₂O₃ (3/2 ratio) to 63 mole % A1₂O₃. Metastable solid solutions can be prepared up to about 67 mole % Al₂O₃. There is no evidence for stable solubility of excess SiO₂ beyond the 3/2 composition at pressures below 3 kbars. Refractive indices are presented for glasses containing up to 60 mole % Al₂O₃ and from them the composition of the eutectic is confirmed at 5 mole % SiO₂. The variation in lattice constants of the mullite solid solution is not an unequivocal guide to composition since mullites at one composition produced at different temperatures show differences in spacing, no doubt reflecting Al-Si ordering phenomena. The possibility of quartz and corundum being the stable assemblage at some low temperatures and pressures cannot be ruled out. A new anhydrous phase in the system is described, which was previously thought to be synthetic andalusite; it is probably a new polymorph of the Al₂SiO₅ composition with ortho-rhombic unit-cell dimensions a =7.55 A, b =8.27 A, and c = 5.66 A.     

Properties of Sm2O3─Al2O3─SiO2 Glasses for In Vivo Applications

The compositional range for glass formation below 1600°C in the Sm₂O₃─Al₂O₃─SiO₂ system is (9–25)Sm₂O₃─(10–35)Al₂O₃─(40–75)SiO₂ (mol%). Selected properties of the Sm₂O₃─Al₂O₃─SiO₂ (SmAS) glasses were evaluated as a function of composition. The density, refractive index, microhardness, and thermal expansion coefficient increased as the Sm₂O₃ content increased from 9 to 25 mol%, the values exceeding those for fused silica. The dissolution rate in 1 N HCl and in deionized water increased with increasing Sm₂O₃ content and with increasing temperature to 70°C. The transformation temperature ( T _g ) and dilatometric softening temperature ( T _d ) of the SmAS glasses exceeded 800° and 850°C, respectively.     

Sintering and Crystallization of CaO–Al2O3–ZrO2–SiO2 Glasses Containing Different Amount of Al2O3

In this work several complementary techniques have been employed to carefully characterize the sintering and crystallization behavior of CaO–Al₂O₃–ZrO₂–SiO₂ glass powder compacts after different heat treatments. The research started from a new base glass 33.69 CaO–1.00 Al₂O₃–7.68 ZrO₂–55.43SiO₂ (mol%) to which 5 and 10 mol% Al₂O₃ were added. The glasses with higher amounts of alumina sintered at higher temperatures (953°C [lower amount] vs. 987°C [higher amount]). A combination of the linear shrinkage and viscosity data allowed to easily find the viscosity values corresponding to the beginning and the end of the sintering process. Anorthite and wollastonite crystals formed in the sintered samples, especially at lower temperatures. At higher temperatures, a new crystalline phase containing ZrO₂ (2CaO·4SiO₂·ZrO₂) appeared in all studied specimens.     

Structure of B2O3 and Binary Aluminoborate Melts at 1600°C

Viscosity and density data were obtained up to 1700°C for a series of binary aluminoborate melts that contained as much as 15 mole% (∼21 wt%) Al₂O₃ and up to 1620°C for pure molten B₂O₃. Large expansion coefficient decreases and a slight activation energy increase for B₂O₃ above 1400°C suggested a tightening of its structure. The addition of Al₂O₃ reduced viscosity and increased activation energy. The decreased compositional dependence of molar volume (compared to SiO₂ additions) and the increased expansion coefficients accompanying Al₂O₃ additions suggested a loosening of the O—B—O structure at 1600°C. Molar volume deviations from ideality were similar to but smaller than those for SiO₂ and GeO₂ additions at 1300°C. Microclustering of aluminum-bearing polyhedra appeared to occur at slightly higher boron atom contents than with SiO₂ and GeO₂ additions.     

Crystallization Behavior of Al2O3 in the Presence or SiO2

The independent crystallization sequence of an Al₂O₃ component is modified in the presence of SiO₂ and vice versa. Mixed SiO₂-Al₂O₃, gel (28 wt% SiO₂ and 72 wt% Al₂O₃) forms neither cristobalite nor γ-Al₂O₃ and corundum at 1000°C but forms Si-Al spinel; an amorphous aluminosilicate phase invariably also forms after the gel is heated. However, the composition of this amorphous aluminosilicate phase is not as yet known.     

Al2O3–ZrO2–SiO2 Ternary Glasses for Molybdenum Oxidation Barriers

The wettability of binary and ternary glasses belonging to SiO₂–Al₂O₃–ZrO₂ diagram has been studied using the sessile drop technique at 1750° and 1800°C. The ternary SiO₂–Al₂O₃–ZrO₂ (90–5–5 wt%) glass has proved to be well appropriated as a molybdenum oxidation barrier coating. The addition of 5 wt% of MoO₂ slightly improves its wettablity at higher temperatures without affecting its oxidation barrier properties. The Mo comes into the glass network as a mixture of Mo⁵⁺, Mo⁴⁺, and Mo⁶⁺. After oxidation at 1000°C in oxygen atmosphere, the molybdenum remains in the glass network as Mo⁶⁺.     

Change in Chemical Composition of Mullite Formed from 2SiO2°3Al2O3 Xerogel During the Formation Process

The chemical composition of mullite which was termed from 2SiO₂3Al₂O₃ xerogel by firing was examined by analytical TEM. Mullite formed at 950°C firing showed around 66 mol% Al₂O₃, which was fairly Al₂O₃ rich compared with the bulk composition. The chemical composition of mullite gradually approached the bulk composition as the firing temperature increased to 1400°C and slightly departed again above that firing temperature.     

Application of Compositionally Diphasic Xerogels for Enhanced Densification: The System Al2O3-SiO2

Stoichiometric mullite (71.38 wt% Al₂O₃-28.17 wt% SiO₂) and 80 wt% Al₂O₃-20 wt% SiO₂ gels were prepared by the single-phase and/or diphasic routes. Dense sintered bodies were prepared from both sets of gels in the Al₂O₃-SiO₂ system. Apparent densities of 96% and 97% of theoretical density were measured for the diphasic (using two sols) mullite samples sintered at 1200° and 1300°C for 100 min, respectively; this compared with 85% and 94% for the single-phase xerogels under the same conditions, and to much lower values for mullite prepared from conventional mixed powders. The microstructure of the mullite pellets from diphasic xerogel precursors is also considerably finer.     

Preparation of NiAl2O4/SiO2 and Co2+-Doped NiAl2O4/SiO2 Nanocomposites by the Sol–Gel Route

NiAl₂O₄/SiO₂ and Co²⁺-doped NiAl₂O₄/SiO₂ nanocomposite materials of compositions 5% NiO – 6% Al₂O₃– 89% SiO₂ and 0.2% CoO – 4.8% NiO – 6% Al₂O₃– 89% SiO₂, respectively, were prepared by a sol–gel process. NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals were grown in a SiO₂ amorphous matrix at around 1073 K by heating the dried gels from 333 to 1173 K at the rate of 1 K/min. The formations of NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals in SiO₂ amorphous matrix were confirmed through X-ray powder diffraction, Fourier transform infrared spectroscopy, differential scanning calorimeter, transmission electron microscopy (TEM), and optical absorption spectroscopy techniques. The TEM images revealed the uniform distribution of NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals in the amorphous SiO₂ matrix and the size was found to be ∼5–8 nm.     

Quaternary System Al2O3–CaO–MgO–SiO2: I, Study of the Crystallization Volume of Al2O3

Compatibility relations of Al₂O₃ in the quaternary system Al₂O₃–CaO–MgO–SiO₂ were studied by firing and quenching followed by microstructural and energy-dispersive X-ray examination. A projection of the liquidus surface of the primary phase volume of Al₂O₃ was constructed in terms of the CaO, SiO₂, and MgO contents of the mixtures recalculated to 100 wt%. Two invariant points, where four solids coexist with a liquid phase, were defined, and the positions of the isotherms were tentatively established. The effect of SiO₂, MgO, and CaO impurities on Al₂O₃ growth also was studied.     

Isothermal Section of a Cu2O–Al2O3–SiO2 Pseudo-Ternary System at 1150°C in Air

In this study, the isothermal section of a Cu₂O–Al₂O₃–SiO₂ pseudo-ternary phase diagram at 1150°C was analyzed by means of a scanning electronic microscope and powder X-ray diffraction of the quenched samples qualitatively, and the compositions of the tie-points of the tie-planes as well as their regions were determined by in situ high-temperature quantitative X-ray diffraction analysis and energy-dispersive X-ray spectroscopy. Then, the isothermal section of the Cu₂O–Al₂O₃–SiO₂ pseudo-ternary phase diagram at 1150°C was constructed; it was found that the isothermal section is composed of two single liquid-phase regions, five two-phase regions, and six three-phase regions.     

Phase Equilibrium Relationships in a Portion of the System MgO–Al2O3–2CaO·SiO2

The system MgO–Al₂O₃–2CaO·SiO₂ comprises a plane through the tetrahedron CaO–MgO–Al₂O₃–SiO₂. A total of 108 compositions were prepared having an alumina content below the line joining 2CaO·Al₂O₃SiO₂ (gehlenite) and MgO·Al₂O₃ (spinel). Quenching experiments were carried out on 96 of these compositions at temperatures up to 1590°C. Three binary eutectic systems and two ternary eutectic systems are described. Compositions on this plane are of significance in an investigation of the constitution of basic refractory clinkers made from Canadian dolomitic magnesites. They also concern the compositions of certain blast furnace slags.     

Eletrical Properties of Glasses in the System PbO-Al2O3-B2O3-SiO2

Glasses in the system Pb0–Al₂O₃-B₂O₃-SiO₂ are chemically stable over a wide composition range and have very desirable electrical characteristics such as high electrical resistivities and activation energies for conduction. Variations in these electrical properties were studied as a function of composition changes within the system, the object being to identify the role of the constituent oxides in achieving the highest activation energy and resistivity values consistent with moderate preparation temperatures. Measurements were made in the temperature range 25° to 400°C on carefully prepared glass disks in which the individual oxide components or different oxide ratios such as PbO/SiO₂, Al₂O₃/SiO₂, and B_sO₃/SiO₁ were systematically varied. The activation energy and resistivity values obtained ranged from 1.2 to 1.6 ev and 10° to 10¹⁴ ohm-cm, with dielectric constants ranging from 9 to 19 and densities from 4.30 to 4.50 g/cmY. Indications were that, for the composition range studied, the behavior manifested was basically that of the binary PbO-SO₂ glass with additions of Al₂O₃ or B₂O₃, even in small concentrations, sharply increasing the activation energy for conduction while lowering the density.     

Reaction Between K2O and Al2O3-SiO2 Refractories as Related to Blast-Furnace Linings

An examination was conducted to determine the mechanism of peeling of fire-clay brick in the low-temperature region of a blast furnace where 3 to 10% K₂O is the principal contaminant. In laboratory tests, as-received high-duty and superduty fire-clay brick and 70% alumina brick treated with KCl-K₂CO₃ mixtures showed no peeling at a temperature of 1600°F. Cracks were found in high-duty brick that were treated with KCN at 1500°F. under partially reducing conditions. X-ray diffraction studies of mixtures of crushed brick and K₂CO₃ indicated the formation of leucite (K₂O.Al₂O₃.4SiO₂) and kaliophilite (K₂O.-Al₂O₃.2SiO₂) at temperatures below 1700°F. These latter data, confirmed by specimens from used blast-furnace linings, showed that silica is the first constituent attacked by alkali. Since the formation of leucite and kaliophilite in fire-clay brick is the probable cause of peeling, the increased reaction of silica, in a dense Al₂O₃.SiO₂ refractory of higher silica content than fire-clay brick, should confine the alkali attack to the surface of the brick in low-temperature applications.     

Cassiterite Solubility in High-Silica K2O-Al2O3-SiO2 Liquids

The saturation surface of cassiterite, SnO₂, was determined for liquids in the system K₂O–Al₂O₃–SiO₂ as a function of bulk composition and temperature. At fixed K₂O/Al₂O₃ cassiterite solubility varies weakly with SiO₂ concentration (76 to 84 mol%), temperature (1350° to 1550°C), and log ( f _O2) (−0.7 to −5.3). Cassiterite solubility is also approximately independent of composition in liquids with molar ratios of K₂O/Al₂O₃ lessthan equal to 1 (peraluminous liquids). As K₂O/Al₂O₃ increases from 1 (peralkaline liquids), however, cassiterite solubility increases steeply and approximately linearly with K₂O in excess of Al₂O₃. It is proposed that potassium in excess of aluminum combines with Sn⁴⁺ to form quasi-molecular complexes with an effective stoichiometry of K₄SnO₄.     

Quaternary System Al2O3–CaO–MgO–SiO2: II Study of the Crystallization Volume of MgAl2O4

Solid-state compatibility and melting relations of MgAl₂O₄ in the quaternary system Al₂O₃–CaO–MgO–SiO₂ were studied by firing and quenching selected samples located in the 65 wt% MgAl₂O₄, plane followed by microstructural and energy dispersive X-ray analysis. A projection of the liquidus surface of the primary crystallization volume of MgAl₂O₄ was constructed from CaO, SiO₂ and exceeding Al₂O₃, not involved in stoichiometric MgAl₂O₄ formation; those three amounts were recalculated to 100 wt%. The temperature and character of six invariant points, where four solids co-exist with a liquid phase, were defined. One maximum point was localized and the positions of the isotherms were tentatively established. The effect of CaO, SiO₂, and Al₂O₃ impurities on the high temperature behavior of spinel materials was also discussed.     

Glass Formation and Recrystallization in the Lithium Metasilicate Region of the System Li2O–Al2O3–SiO2

The stability of the vitreous state in the lithium metasilicate region of the system Li₂O–Al₂O₃–SiO₂ was found to be a function of the concentration of lithia. The higher the lithia content, the less stable was the glass. The devitrification of glasses in this system was studied. In addition to the phases present at or near the liquidus, it was found that the β -eucryptite– β -quartz solid solution phase was metastable over most of the region. The Li₂O–SiO₂, β -Li₂O–Al₂O₃–4SiO₂ solid solution, β -Li₂O–Al₂O₃–2SiO₂ solid solution triple point was estimated to be near 62.5% SiO₂, 17% Al₂O₃, and 20.5% Li₂O (by weight). The thermal expansions of bodies in this region were measured and the values obtained are explained in terms of the phases present.