From pollutant to solution of wastewater pollution: Synthesis of activated carbon from textile sludge for dye adsorption

Adsorption is an important process in wastewater treatment,and conversion of waste materials to adsorbent offers a solution to high material cost related to the use of commercial activated carbon.This study investigated the adsorption behaviour of Reactive Black 5(RB5)and methylene blue(MB)onto activated carbon produced from textile sludge(TSAC).The activated carbon was synthesized through chemical activation of precursor followed with carbonization at 650°C under nitrogen flow.Effects of time(0–200 min),pH(2–10),temperature(25–60°C),initial dye concentration(0–200 mg·L~(-1)),and adsorbent dosage(0.01–0.15 g)on dye removal efficiency were investigated.Preliminary screening revealed that TSAC synthesized via H_2SO_4activation showed higher adsorption behaviour than TSAC activated by KCl and ZnCl_2.The adsorption capacity of TSAC was found to be 11.98 mg·g~(-1)(RB5)and 13.27 mg·g~(-1)(MB),and is dependent on adsorption time and initial dye concentration.The adsorption data for both dyes were well fitted to Freundlich isotherm model which explains the heterogeneous nature of TSAC surface.The dye adsorption obeyed pseudo-second order kinetic model,thus chemisorption was the controlling step.This study reveals potential of textile sludge in removal of dyes from aqueous solution,and further studies are required to establish the applicability of the synthesized adsorbent for the treatment of waste water containing toxic dyes from textile industry.     

Synthesis of calix[6]arene based XAD‐4 material for the removal of reactive blue 19 from aqueous environments

This study describes the synthesis of calix[6]arene (C6) appended Amberlite XAD‐4 resin and its application for the removal of anthraquinone‐based reactive blue 19 (RB‐19) dye from aqueous environments. The C6‐resin 5 was characterized with various analytical techniques, including Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, and elemental analysis. Adsorption experiments were carried out to investigate the effects of the pH, adsorbent dosage, electrolyte, contact time, and temperature on the adsorption of RB‐19 dye onto the C6‐resin 5. From the results, we observed that the percentage adsorption of the RB‐19 dye was highly dependent on the concentration of electrolyte and the pH of the solution. The maximum adsorption was achieved at pH 9. The thermal study demonstrated that the adsorption process was endothermic and spontaneous in nature. The isothermic study showed that the adsorption behavior could be better demonstrated by the Langmuir and Dubinin and Radushkevich isotherm model. From field studies, it has been concluded that C6‐resin 5 is an effective adsorbent for the removal of RB‐19 dye. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 776‐785, 2013     

Kinetics and equilibrium studies of removal of an azo dye from aqueous solution by adsorption onto scallop

In the present work removal of an azo dye (Reactive Black 5) was investigated from aqueous solution by adsorption onto scallop as a low-cost and widely available adsorbent. The effect of various operational parameters, such as contact time, pH, initial dye concentration and adsorbent dosage on the removal efficiency of dye was studied. Removal efficiency declined with the increase in solution pH and initial dye concentration but with the decrease in adsorbent dosage. Experimental equilibrium and kinetics data were fitted by Langmuir and Freundlich isotherms and pseudo-first-order and pseudo-second-order kinetic models, respectively.     

Dye removal from colored‐textile wastewater using chitosan‐PPI dendrimer hybrid as a biopolymer: Optimization,kinetic, and isotherm studies

Preparation of a biopolymer chitosan‐polypropylene imine (CS‐PPI) as a biocompatible adsorbent and its reactive textile dyes removal potential were performed. Chemical specifications of CS‐PPI were determined using Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR. The surface morphology of the CS‐PPI surface was characterized by scanning electron microscopy. Results confirmed that the linkages between the NH₂ groups of PPI dendrimer and carboxylic groups of modified Chitosan were accomplished chemically. Two textile reactive dyes, reactive black 5 (RB5) and reactive red 198 (RR198), were used as model compounds. A response surface methodology was applied to estimate the simple and combined effects of the operating variables, including pH, dye concentration, time contact, and temperature. Under the optimal values of process parameters, the dye removal performance of 97 and 99% was achieved for RB5 and RR198, respectively. Furthermore, the isotherm and kinetic models of dyes adsorption were performed. Adsorption data represented that both examined dye followed the Langmuir isotherm. The adsorption kinetics of both reactive dyes were satisfied by pseudo‐second order equation. Based on this study, CS‐PPI due to having high adsorption capacity (6250 mg/g for RB5 and 5882.35 mg/g for RR198), biocompatibility and ecofriendly properties might be a suitable adsorbent for removal of reactive dyes from colored solutions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Adsorption of anionic dyes on poly(epicholorohydrin dimethylamine) modified bentonite in single and mixed dye solutions

The performance of poly(epicholorohydrin dimethylamine) modified bentonite (EPIDMA/bentonite) as an adsorbent to remove anionic dyes, namely Direct Fast Scarlet, Eosin Y and Reactive Violet K-3R, was investigated in single, binary and ternary dye systems. In adsorption experiments in single dye solutions, the adsorption of the three dyes onto EPIDMA/bentonite was described by the Langmuir isotherm model and the pseudo-second-order kinetic model. At low dosage of EPIDMA/bentonite, preferential adsorption was observed for the dye with higher affinity to the adsorbent in mixed dye systems. The reduction in uptake of the dye with increasing equilibrium dye concentration in the isotherm and desorption in the kinetic curves were observed for the dye with lower affinity. The total amount of dyes adsorbed versus the total equilibrium dye concentrations were fitted well by the Langmuir isotherm model. The kinetics of the total adsorbed amount of dyes followed the pseudo-second-order kinetic model. The effect of the dosage of adsorbent on color removal efficiency, residual color distribution and adsorption kinetics was investigated.     

Synthesis of an ordered mesoporous carbon with graphitic characteristics and its application for dye adsorption

An ordered mesoporous carbon (OMC) was prepared by a chemical vapor deposition technique using liquid petroleum gas (LPG) as the carbon source. During synthesis, LPG was effectively adsorbed in the ordered mesopores of SBA-15 silica and converted to a graphitic carbon at 800 °C. X-ray diffraction and nitrogen adsorption/desorption data and high-resolution transmission electron microscopy (HRTEM) of the OMC confirmed its ordered mesoporous structure. The OMC was utilized as an adsorbent in the removal of dyes from aqueous solution. A commercial powder activated carbon (AC) was also investigated to obtain comparative data. The efficiency of the OMC for dye adsorption was tested using acidic dye acid orange 8 (AO8) and basic dyes methylene blue (MB) and rhodamine B (RB). The results show that adsorption was affected by the molecular size of the dye, the textural properties of carbon adsorbent and surface-dye interactions. The adsorption capacities of the OMC for acid orange 8 (AO8), methylene blue (MB) and rhodamine B (RB) were determined to be 222, 833, and 233 mg/g, respectively. The adsorption capacities of the AC for AO8, MB, and RB were determined to be 141, 313, and 185 mg/g, respectively. The OMC demonstrated to be an excellent adsorbent for the removal of MB from wastewater.     

Kinetic and equilibrium studies on the biosorption of textile dyes onto Plantago ovata seeds

The powdered seeds of Plantago ovata (PSPO) were utilized for the removal of Malachite Green (MG) and Rose Bengal (RB) dyes from aqueous media by batch adsorption. The Fourier transform infra red spectroscopy (FTIR) results showed that both the dyes were adsorbed between the cellulose matrices, and this has been verified from the intensifying and narrowing aromatic C-H bending vibration. The morphology of the dye laden adsorbent was studied by scanning electron microscopy (SEM), which showed that the dyes were adsorbed between the cellulose matrices of the adsorbent. The PSPO was found to be very effective for the removal of MG and RB at pH 7, and equilibrium was attained within 200 min. The kinetic study indicated that the rate limiting step for MG and RB adsorption may be chemisorption and intraparticle diffusion. Adsorption equilibrium data were fitted to Langmuir, Freundlich, Redlich-Peterson and Temkin adsorption isotherms. It is inferred from the equilibrium studies that the adsorption of MG follows the Freundlich isotherm and the adsorption of RB follows the Langmuir isotherm. The maximum monolayer adsorption capacity of the PSPO was found to be 86.23 mg/g for MG and 81.23 mg/g for RB, respectively.     

Removal of methylene blue dye from aqueous solution by activated carbon prepared from cashew nut shell as a new low-cost adsorbent

Methylene blue dye was adsorbed on an adsorbent prepared from cashew nut shell. A batch adsorption study was carried out with variable adsorbent amount, initial dye concentration, contact time and pH. Studies showed that the pH of aqueous solutions affected dye removal as a result of removal efficiency increased with increasing solution pH. The experimental data were analyzed by the Langmuir, Freundlich, Redlich-Peterson, Koble-Corrigan, Toth, Temkin, Sips and Dubinin-Radushkevich models of adsorption using MATLAB 7.1. The experimental data yielded excellent fits within the following isotherm order: Redlich-Peterson>Toth>Sips>Koble-Corrigan>Langmuir>Temkin>Dubinin-Radushkevich>Freundlich, based on its correlation coefficient values. Three simplified kinetic models including a pseudofirst-order, pseudo-second-order and intraparticle diffusion equations were selected to follow the adsorption process. It was shown that the adsorption of methylene blue could be described by the pseudo-second-order equation. The results indicate that cashew nut shell activated carbon could be employed as a low cost alternative to commercial activated carbon in the removal of dyes from wastewater.     

Isotherm,Kinetic, and Thermodynamic of Cationic Dye Removal from Binary System by Feldspar

In this paper, the isotherm, kinetic, and thermodynamic of cationic dye removal onto inorganic adsorbent (Feldspar) were investigated in single and binary systems. Basic Red 18 (BR18) and Basic Blue 41 (BB41) were used as cationic dyes. The characterization of the Feldspar was carried out using X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) techniques. The effect of operational parameters such as adsorbent dosage, initial dye concentration, pH, ionic strength, and temperature on dye removal was studied. It was found that the adsorption of BR18 and BB41 onto Feldspar followed with Langmuir and extended Langmuir isotherms in single and binary systems, respectively. Adsorption kinetic of dyes was found to conform to pseudo-second order kinetic in single and binary system. The thermodynamic data showed that dye adsorption onto Feldspar was spontaneous, endothermic, and physisorption reaction. Based on the data of the present investigation, one could conclude that the Feldspar as an eco-friendly and low-cost adsorbent might be a suitable alternative to remove dyes from colored aqueous solutions containing cationic dyes.     

Reactive dye removal in dye/salt mixtures by nanofiltration membranes containing vinylsulphone dyes: effects of feed concentration and cross flow velocity

In this study, DS5 DK type nanofiltration membranes were tested to recycle the reactive dye bath effluents. Reactive black 5 (RB5), reactive orange 16 (RO16), reactive blue 19 (RB19) and NaCl were used in the experiments to prepare the synthetic dye and salt mixtures. Effects of feed concentration, pressure and cross flow velocity on the permeate flux and color removal were investigated. Permeate flux increased with increasing pressure for all NaCl solutions. Dye concentration had a significant effect on flux values. Under the fixed NaCl concentrations the flux decreased with increasing dye concentrations. Dye rejections greater than 99% were achieved. Permeate was almost colorless. A gel layer formed by the rejected dye on membrane surface operates as a resistance to the permeation of dyes due to complete rejection of high molecule weight dyes, especially for the low salt concentrations. The presence of salt concentration has an interesting effect on color removal. Color removal decreased with increasing salt concentration. Cross flow velocities had also a significant effect on flux values. The dye formed agglomerates at high NaCl concentrations. High cross flow velocities decreased this effect.     

Preparation of magnetic graphene oxide/chitosan composite beads for effective removal of heavy metals and dyes from aqueous solutions

In this report, a composite adsorbent in form of spherical beads generated from graphene oxide, chitosan, and magnetite (MGOCS) was developed and characterized by X-ray powder diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscope, and vibrating sample magnetometer. The adsorption ability of MGOCS towards reactive blue 19 (RB19) and Ni(II) ions, and the effect of various experimental factors including pH, adsorbent dosage, contact time, adsorbate concentration, temperature, and ionic strength were assessed in detail. The maximum adsorption capacities of MGOCS were 102.06?mg/g for RB19 and 80.48?mg/g for Ni(II). The adsorption process was thermodynamically favorable, spontaneous, exothermic, and best described by Langmuir (for Ni(II)) and Freundlich (for RB19) isotherms. The adsorption kinetics were well fitted with pseudo-first-order model for both adsorbates. The result indicated that the beads have feasibility as highly efficient and eco-friendly adsorbent to get rid of organic dyes and heavy metals from water due to their high adsorption capacity, easy recovery, and reusability.     

The adsorption of malachite green (MG) as a cationic dye onto functionalized multi walled carbon nanotubes

Synthetic dyes are widely used by several industries to color their products. The discharge of colored wastewater into the hydrosphere causes serious environmental problems. We used functionalized multi wall carbon nanotubes as an adsorbent for the adsorption of cationic dye, malachite green, from aqueous solution. Based on information provided by the Iranian Research Institute of Petroleum Industry, carbon nanotubes are produced using a chemical vapor deposition (CVD) technique. These as-received MWCNTs were functionalized by acid treatment. The remaining dye concentration was read by UV-visible absorption spectroscopy at maximum adsorption wavelength. The effect of different operational parameters such as contact time, pH of solution, adsorbent dose and initial dye concentration were studied. The results showed that by increasing of contact time, pH and adsorbent dose the removal of dye increased, but by increasing initial dye concentration, the removal efficiency decreased. Adsorption isotherms and kinetics behavior of f-MWCNTs for removal of malachite green was analyzed, and fitted to various existing models. The experimental data were well correlated with the Langmuir isotherm with a maximum adsorption capacity (q _m ) and regression coefficient (R²) of 142.85 mg/g and 0.997, respectively. The results of this study indicate that functionalized multi wall carbon nanotubes can be used as an effective adsorbent for the removal of dyes.     

Removal of basic and acid dyes from aqueous solutions by a waste containing boron impurity

In this study, batch experiments were carried out for the sorption of basic blue 41 (BB 41), and acid blue 225 (AB 225) onto boron waste (BW) from boron enrichment plant. The operating variables studied are the initial dye concentration, contact time, solution pH, and adsorbent dosage. The experimental equilibrium data were analyzed by using various adsorption isotherm models and the results have shown that the adsorption behavior of AB 225 and BB 41 could be described well reasonably by Langmuir and Temkin isotherms, respectively. Kinetics studies indicated that the adsorption of both dyes follow pseudo-second-order kinetics. The sorption of basic dye increased at high pH values, whereas the opposite was true for acidic dye. The results indicate that BW could be employed as low-cost alternatives to the commercially available adsorbents in wastewater treatment for the removal of acid and basic dyes.     

Adsorption of Rhodamine B Dye on Elaeis guineensis Frond Fiber

Adsorption of Rhodamine B (RB) dye was investigated using raw Elaeis guineensis frond fiber (EGFF). Experiments were performed using face centered composite statistical design with six input parameters namely pH (2-10), agitation speed (150-300 rpm), initial dye concentration (100-500 mg/L), temperature (27-80°C), contact time (10-40 min), and adsorbent dosage (0.5-1.5 g). Particle size of < 45 μm was taken as a fixed input parameter. Regression analysis showed good fit of the experimental data to the second-order polynomial model with coefficient of determination (R²) value of 0.99 and 0.98 for color removal and chemical oxygen demand (COD) reduction, respectively. Two optimum operating conditions for the adsorption of RB were found using RSM, resulted in > 99% of color removal and > 97% of COD reduction. The adsorption process was rapid and fitted to the pseudo-second-order kinetic model, while equilibrium data were favorably described by the Langmuir isotherm. The adsorbent showed excellent reusability with 0.1 M NaOH solution as desorbing agent. The findings make EGFF a promising and low-cost adsorbent for the removal of RB from aqueous solutions.     

NaOH改性花生壳对亚甲基蓝染料吸附性能的研究

花生壳用5%的NaOH溶液改性作吸附剂处理亚甲基蓝染料废水,考察pH值、吸附剂投加量、染料浓度和温度及吸附时间对染料吸附性能的影响。结果表明,吸附最佳的工艺条件为:温度25℃,吸附剂投加量0.3 g,亚甲基蓝的初始浓度3.5 g/mL,反应时间135 min,pH值7。此时改性花生壳对亚甲基蓝的吸附率达99.57%。     

Novel polymorphous aluminosilicate nano minerals: Preparation,characterization and dyes wastewater treatment

Polymorphous aluminosilicate, such as Andalusite, Kyanite and Sillimanite, were prepared and characterized by XRF, XRD, FT-IR and SEM analysis. These cheap and accessible nanoparticles were used for removal of Disperse Red 177 and Disperse Blue 60 dyes. The adsorption process was held in a batch system considering the effects of major parameters consist of pH, adsorbent dosage, dye initial concentration and temperature. The obtained results show that both Freundlich and Temkin isotherms suitably fit with experimental data of adsorption of dyes in equilibrium mode. Also, the adsorption of dyes follows and matches pseudo-second-order kinetic model for Andalusite, Kyanite and Sillimanite nanoadsorbents. Thermodynamic study of dye adsorption process proves low randomness, exothermicity and spontaneous reactions. The comparison of three adsorbent efficiencies for adsorption of DR-177 and D-B-60 dyes was as: Andalusite>Sillimanite>Kyanite and Sillimanite>Kyanite>Andalusite, respectively.     

Adsorption of congo red by three Australian kaolins

This study investigated the potential use of kaolin as alternative adsorbents for removal of congo red from wastewater. The effect of adsorbent dosage, dye concentration, pH and temperature were experimentally studied to evaluate the adsorption capacity, kinetics and equilibrium. Experimental results revealed that optimal adsorption took place at acidic pH and high dye concentration. Ceram kaolin had the highest removal efficiency among studied kaolins, followed by K15GR and Q38. The dye uptake process obeyed the pseudo-second order kinetic expression and was best described by the Langmuir isotherm. Intra-particle diffusion studies showed that the adsorption mechanism was not exclusively controlled by the diffusion step and was more likely to be governed by external mass transfer. Thermodynamic studies showed congo red adsorption on all kaolins was exothermic and spontaneous in nature. Recovered Q38 and K15GR kaolin demonstrated an enhanced adsorption capability. The results indicate that these local kaolins could be employed as low-cost alternatives for removal of anionic dyes from industrial wastewater.     

Removal of Selected Basic Dyes using Activated Carbon from Tannery Wastes

Activated carbon prepared from tannery leather waste (TLW-AC) has been studied for its efficiency of removal of basic dyes, namely rhodamine B (RB), methylene blue (MB), and malachite green (MG) from aqueous solutions. Factors influencing dye adsorption such as the concentration of dye, pH, contact time, and temperature were investigated. The adsorption was found to be strongly dependent on the pH and temperature. The maximum sorption capacity of RB was obtained at pH 3 and for MB and MG was obtained at pH 11. Various thermodynamic parameters such as ΔG°, ΔH°, and ΔS° were calculated. The kinetic studies reveal that the adsorption process follows the pseudo second-order kinetic model. The equilibrium data have been well-described by the Langmuir and Freundlich models, and the data fitted well in both model equations. The study revealed that wastes from leather industry is an economically viable option for dye removal.     

Removal of Acid Violet 17 from Aqueous Solutions by Adsorption onto Activated Carbon Prepared from Pistachio Nut Shell

Adsorbents prepared from pistachio nut shell, an agricultural waste biomass, were successfully used to remove Acid Violet 17 from an aqueous solution. The activated carbons PNS1, PNS2, and PNS3 were characterized by scanning electron microscope (SEM), Fourier Transform – Infra Red spectroscopy (FTIR) and (BET). The effect of pH, adsorbent dosage, and temperature on dye removal was studied. Maximum color removal was observed at pH 2. The adsorption increased with the increase in adsorbent dosage. As the adsorption capacity increased with the increase in temperature, the process was concluded to be endothermic. The experimental data were analyzed by the Langmuir and Freundlich isotherm models of adsorption. Equilibrium data fitted well with the Langmuir model. The rates of adsorption confirmed the pseudo-second order kinetics with good correlation values. The results indicated that the activated carbon prepared from pistachio nut shell can be effectively used for the removal of Acid Violet 17 from aqueous solution.     

Synthesis of urethane sodium carboxylate and its dye removal ability from single system

Urethane sodium carboxylate (USC) was synthesized and its dye removal ability was investigated. USC characteristics were studied using FTIR and SEM. Basic Blue 41 (BB41), Basic Red 18 (BR18), and Basic Violet 16 (BV16) were used. The effect of adsorbent dosage, dye concentration and salt on dye removal was evaluated. Adsorption kinetics followed pseudo-second order. The USC adsorption capacity was 474, 538 and 298 mg/g for BB41, BR18 and BV16, respectively. Adsorption isotherm followed with Langmuir isotherm. The results showed that the USC might be a suitable adsorbent to remove dyes from colored wastewater.