In situ reaction synthesis,microstructure and thermomechanical properties of novel medium-entropy (Ti,V,Nb,Ta)2AlC ceramics

High- and medium-entropy (HE and ME) materials have attracted considerable interest in recent years due to the advantages of designable components and tunable structures with modifiable physicochemical performances. Herein, a dense equiatomic quaternary (Ti,V,Nb,Ta)₂AlC solid solution, or denoted as a medium-entropy MAX phase, was fabricated by in-situ reaction in hot-pressing sintering process using easily available elemental powders as raw materials. X-ray diffraction with its Rietveld refinement analysis, scanning electron microscope and high-resolution scanning transmission electron microscope equipped with energy-dispersed spectrometer analysis identify the phase composition and crystal structure of the novel ME-M₂AlC (Ti,V,Nb,Ta)₂AlC phase. Especially, the atomic-resolution HAADF images directly prove the mutual solution of four metallic elements of the ME (Ti,V,Nb,Ta)₂AlC phase. Both the flexural strength and Vickers hardness are enhanced compared with the reported individual components, and the strengthening and hardening results largely benefit from solid-solution effect with lattice distortion in structure. The fracture toughness has not been enhanced due to the lack of effective toughening mechanism. Furthermore, the electrical conductivity of ME (Ti,V,Nb,Ta)₂AlC ceramic is distinctly decreased as a result of the increasing carrier lattice scattering and point defect scattering, which is caused by severe lattice distortion. Similarly, the scattering effect of solid solutions is also responsible for the lower thermal conductivity. It is worth noting that size disorder parameter (δ_size) is a more effective criterion to evaluate the reduced thermal conductivity than the ideal mixing configurational entropy itself. As a result, applying the medium- and high-entropy design to the MAX phases with chemical and structural diversity can provide a large compositional space with corresponding large range of unexpected performances, which is highly anticipated.     

Synthesis,microstructure and mechanical properties of high-entropy (VNbTaMoW)C5 ceramics

High-entropy ceramics (HEC) with a fixed composition of (VNbTaMoW)C₅ were prepared by spark plasma sintering (SPS) from 1500 °C to 2200 °C. XRD, TEM, HRTEM, SAED and EDX were used to investigate effects of the sintering temperatures on compositional homogeneity, constituent phases and microstructure of the HECs. The results showed that single-phase HEC formed at a temperature as low as 1600 °C while ultimate elemental distribution homogeneity could be obtained at 2200 °C. Elemental distribution homogenization was accompanied by microstructural coarsening and oxide impurities aggregating at grain boundaries as temperature increased. SPS at 1900 °C for 12 min could yield uniform HECs (VNbTaMoW)C₅ with Vickers hardness, nanohardness, fracture toughness and Young’s modulus reaching 19.6 GPa, 29.7 GPa, 5.4 MPa m^1/2 and 551 GPa, respectively. The resultant HECs showed excellent wear resistance when coupled with WC at room temperature.     

Phase stability,mechanical and thermodynamic properties of (Hf,Zr, Ta,M)B2 (M= Nb,Ti, Cr,W) quaternary high-entropy diboride ceramics via first-principles calculations

As the high-entropy design concept applied to the diboride ceramic system, high-entropy diboride ceramics with a wide range of composition control, is expected to become a new high-performance material for extreme high-temperature environments. Herein, the effects of four transition metal elements (Nb, Ti, Cr, W) on the phase stability and properties of (Hf, Zr, Ta)B₂-based high-entropy diboride ceramics are systematically investigated via the first-principles calculations. All components were identified as thermodynamically, mechanically and dynamically stable from enthalpy of formation, elastic and phonon spectrum calculations. Among these, compared with the (Hf, Zr, Ta)B₂ ceramics, the addition of Nb and Ti on the metal sublattice is beneficial to improve the mechanical properties of ceramics, including Young's modulus, hardness and fracture toughness, while the introduction of Cr and W weakens the strength of covalently and ionic bonds inside the material, reducing its mechanical properties. The predicted thermophysical properties show that the high-entropy diboride ceramics containing Nb and Ti have better high-temperature comprehensive performance, including higher Debye temperature, thermal conductivity and lower thermal expansion characteristics, which is conducive to the application in extreme high-temperature environments. This research will provide important guidance for the design and development of new high-performance high-entropy diboride ceramics.     

Synthesis,mechanical, and thermophysical properties of high-entropy (Zr,Ti,Nb,Ta,Hf)C0.8 ceramic

Two high-entropy carbides, including stoichiometric (Zr,Ti,Nb,Ta,Hf)C and nonstoichiometric (Zr,Ti,Nb,Ta,Hf)C_0.8, were prepared from monocarbides and ZrH₂. Their sinterability, microstructures, mechanical properties, thermophysical properties, and oxidation behaviors were systematically compared. With the introduction of carbon vacancy, the sintering temperature was lowered up to 300°C, Vickers hardness was almost unaffected, whereas the strength decreased significantly generally due to the decrease of covalent bonds. The thermal conductivity shows a 50% decrease for nonstoichiometry high-entropy carbide, which is a major consequence of the lower electrical conductivity. The oxidation resistance in high temperature water vapor was not sensitive to carbon stoichiometry.     

Effect of carbon content on the microstructure and mechanical properties of high-entropy (Ti0.2Zr0.2Nb0.2Ta0.2Mo0.2)Cx ceramics

High-entropy (Ti_0.2Zr_0.2Nb_0.2Ta_0.2Mo_0.2)C_x ceramics, with different carbon contents (x=0.55?1), were prepared by spark plasma sintering using powders synthesized via a carbothermal reduction approach. Single-phase, high-entropy (Ti_0.2Zr_0.2Nb_0.2Ta_0.2Mo_0.2)C_x ceramics could be obtained when using a carbon content of x=0.70?0.85. Combined ZrO₂ and Mo-rich carbide phases, or residual graphite, existed in the ceramics due to either a carbon deficiency or excess at x=0.55 and 1, respectively. With the carbon content increased from x=0.70 to x=0.85, the grain size decreased from 4.36 ± 1.55 μm to 2.00 ± 0.91 μm, while the hardness and toughness increased from 23.72 ± 0.26 GPa and 1.69 ± 0.21 MPa·m^1/2 to 25.45 ± 0.59 GPa and 2.37 ± 0.17 MPa·m^1/2, respectively. This study showed that the microstructure and mechanical properties of high-entropy carbide ceramics could be adjusted by the carbon content. High carbon content is conducive to improving hardness and toughness, as well as reducing grain size.     

Pressureless sintering and properties of (Hf0.2Zr0.2Ta0.2Nb0.2Ti0.2)C high-entropy ceramics: The effect of pyrolytic carbon

A novel (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C high-entropy ceramic was successfully prepared by pressureless sintering at 2200 °C. With increasing content of resin-derived-carbon, the density, and mechanical and thermal properties increased up to a maximum content of 2～4 wt% resin addition, after which further addition was detrimental. All specimens showed high strength (≥347±36 MPa), with the highest value achieving 450±64 MPa, and fracture toughness significantly higher (>20 %) than those of the corresponding monocarbides and Ta_0.5Hf_0.5C, (Ta_1/3Zr_1/3Nb_1/3)C. The thermal conductivity was approximately equivalent to the lowest value of the corresponding mono-carbides, which was assumed to be due to the lattice distortion effect.     

Microstructure evolution,mechanical and tribological properties of Ti3(Al,Sn)C2/Al2O3 composites

In this paper, in situ formed Ti₃(Al,Sn)C₂/Al₂O₃ composites were fabricated by sintering the mixture of Ti₃AlC₂ and SnO₂. The Al atoms could diffuse out of the Ti₃AlC₂ layered structure to react with SnO₂, resulting in the formation of Ti₃(Al,Sn)C₂ solid solution and Al₂O₃. When the SnO₂ content was 20?wt.%, the sintered Ti₃(Al,Sn)C₂/Al₂O₃ composite exhibited the best overall mechanical properties, because of the optimized cooperative strengthening effect of solution strengthening and Al₂O₃ enhancement. When the SnO₂ content increased up to 30?wt.%, the flexural strength and fracture toughness of Ti₃(Al,Sn)C₂/Al₂O₃ composite dramatically decreased on account of the large accumulation of generated Al₂O₃. Moreover, according to the SiC ball-on-flat wear tests, it was found that the wear resistance of Ti₃(Al,Sn)C₂/Al₂O₃ composites was significantly improved as the SnO₂ content increased.     

A multicomponent porous MAX phase (Ti0.25Zr0.25Nb0.25Ta0.25)2AlC: Reaction process,microstructure and pore formation mechanism

A multicomponent porous MAX phase (Ti_0.25Zr_0.25Nb_0.25Ta_0.25)₂AlC has been successfully synthesized by using pressureless sintering of mixed elemental powders. The microstructure and phase composition of the samples sintered at various temperatures have been characterized by using SEM, XRD, EDS and other analyses, from which conclusions regarding the reaction and pore forming processes could be drawn. During the whole sintering process, the pores did mainly arise from the diffusion related reactions between Al and other elements at low temperatures (below 1200 °C), and the formation reaction of the MAX phase took place at higher temperatures (above 1200 °C). An exception is the clearance holes that were left from the pressing. The optimum sintering temperature for the final MAX phase (Ti_0.25Zr_0.25Nb_0.25Ta_0.25)₂AlC was 1600 °C. A too high sintering temperature (1700 °C) caused a serious loss of Al atoms and a decomposition of the synthesized MAX phase.     

Novel (Zr,Ti)B2-(Zr,Ti)C-SiC ceramics via reactive hot pressing

Fully dense (Zr, Ti)B₂-(Zr, Ti)C-SiC ceramics were prepared by reactive hot-pressing using ZrB₂, TiC, and SiC as the initial materials for the first time. Effects of SiC addition on the microstructure evolution and mechanical properties were reported. The in-situ reaction between ZrB₂ and TiC as well as the SiC addition leads to the grain refinement. Besides, elongated (Zr, Ti)B₂ plate-like grains are obtained due to the occurrence of a transient liquid phase, which leads to the crack deflection in the matrix effectively. Mechanical properties are improved significantly due to grain-refinement and solid solution strengthening, and plate-like grains toughening effects. The ZrB₂-10 mol%TiC composite with 10 mol% SiC additional exhibits good comprehensive mechanical properties of the hardness of 20.2 GPa, the flexural strength of 803 MPa, and the fracture toughness of 5.7 MPa m^1/2.     

Diffusion bonding of (Hf0.2Zr0.2Ti0.2Ta0.2Nb0.2)C high-entropy ceramic with metallic Ni foil

To prepare large-sized and complex-shaped components, the feasibility of direct diffusion bonding of (Hf_0.2Zr_0.2Ti_0.2Ta_0.2Nb_0.2)C high-entropy ceramic (HEC) and its diffusion bonding with a metallic Ni foil was investigated, and the interfacial microstructure and mechanical properties of HEC/HEC and HEC/Ni/HEC joints were analyzed. For the direct diffusion bonding, reliable joints with a shear strength of 146 MPa could be achieved when the bonding temperature reached 1500 °C under a pressure of 30 MPa. By introducing a metallic Ni foil as the interlayer, the HEC was successfully bonded at the diffusion temperatures from 1150 °C to 1250 °C under 10 MPa through the formation of Ti₂Ni compound phase. Meanwhile, the HEC(Ni) phase formed by the diffusion of Ni into HEC and Ni(s, s) bulks precipitated in the bonding transition zone. The maximum joint shear strength of 151 MPa was obtained by optimizing the Ni-foil thickness, bonding temperature, and holding time.     

Synthesis,microstructure and properties of ternary layered i-MAX (Mo2/3M1/3)2AlC (M = Sc and Lu) ceramics fabricated by spark plasma sintering

Recently, a new i-MAX phase with in-plane chemical order has been discovered. In this study, the i-MAX phase (Mo_2/3Sc_1/3)₂AlC and (Mo_2/3Lu_1/3)₂AlC ceramics were synthesized by spark plasma sintering (SPS) with purity up to 96.45 wt% and 95.46 wt%, respectively. Relative densities were up to 98.29 % (M = Sc) and 98.23 % (M = Lu). Microstructure, physical and mechanical properties of (Mo_2/3M_1/3)₂AlC (M = Sc and Lu) ceramics were systematically investigated. Grain sizes of (Mo_2/3M_1/3)₂AlC (M = Sc and Lu) were also counted. The measured coefficients of thermal expansion (CTE) were 8.95 × 10⁻⁶ K⁻¹ (M = Sc) and 8.97 × 10⁻⁶ K⁻¹ (M = Lu), from 25 °C to 1200 °C. Regarding mechanical properties, the Vickers hardness of (Mo_2/3Lu_1/3)₂AlC was much higher than that of (Mo_2/3Sc_1/3)₂AlC, while the differences in flexural strength, fracture toughness and compressive strength were small. It indicates that both ceramics have good application prospects.     

First-principles prediction,fabrication and characterization of (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)B2 high-entropy borides

The microstructure and mechanical properties of (Hf_0.2Nb_0.2Ta_0.2Ti_0.2Zr_0.2)B₂ high-entropy boride (HEB) were first predicted by first-principles calculations combined with virtual crystal approximation (VCA). The results verified the suitability of VCA scheme in HEB studying. Besides, single-phase (Hf_0.2Nb_0.2Ta_0.2Ti_0.2Zr_0.2)B₂ ceramics were successfully fabricated using boro/carbothermal reduction (BCTR) method and subsequent spark plasma sintering (SPS); furthermore, the effects of different amounts of B₄C on microstructure and mechanical properties were evaluated. Due to the addition of B₄C and C, all samples formed single-phase solid solutions after SPS. When the excess amount of B₄C increased to 5 wt%, the sample with fine grains exhibited superior comprehensive properties with the hardness of 18.1 ± 1.0 GPa, flexural strength of 376 ± 25 MPa, and fracture toughness of 4.70 ± 0.27 MPa m^1/2. Nonetheless, 10 wt% excess of B₄C coarsened the grains and decreased the strength of the ceramic. Moreover, the nanohardness (34.5–36.9 GPa) and Young's modulus (519–571 GPa) values with different B₄C contents just showed a slight difference and were within ranges commonly observed in high-entropy diboride ceramics.     

Low temperature sintering of Hf0.95Nb0.05B2-based ceramics with submicron-scaled grains and enhanced mechanical properties

Hf_0.95Nb_0.05B₂ ceramics and their composites containing 20 vol% SiC were prepared via high-pressure spark plasma sintering in the study. The densification, microstructures, and mechanical properties of the prepared materials were then investigated. It is challenging to achieve full densification of HfB₂ ceramics, even with markedly refined Hf_0.95Nb_0.05B₂ solid solution powder under the sintering conditions of 2000 °C/30 MPa. However, under the sintering conditions of 1700 °C/200 MPa, a dense microstructure of Hf_0.95Nb_0.05B₂ ceramics was achieved. Moreover, the Hf_0.95Nb_0.05B₂-20 vol% SiC composite was densified at a lower temperature (1500 °C) and exhibited ultrafine grains (300 nm) and high-density defects, including stacking faults, Lomer-Cottrell locks, and twins, thus resulting in exceptional comprehensive mechanical properties, such as ultra-high hardness (32 GPa) and significantly improved fracture toughness (5.2 MPa.m^1/2).     

Densification,microstructure, and mechanical properties of V-substituted HfB2-based ceramics

This study firstly developed Hf_1-xV_xB₂ (x = 0, 0.01, 0.02, 0.05) powders, which were derived from borothermal reduction of HfO₂ and V₂O₅ with boron. The results revealed that significantly refined Hf_1-xV_xB₂ powders (0.51 μm) could be obtained by solid solution of VB₂, and x ≥ 0.05 was a premise. However, as the content of V-substitution for Hf increased, Hf_1-xV_xB₂ ceramics sintered by spark plasma sintering at 2000 °C only displayed a slight densification improvement, which was attributed to the grain coarsening effect induced by the solid solution of VB₂. By incorporating 20 vol% SiC, fully dense Hf_1-xV_xB₂-SiC ceramics were successfully fabricated using the same sintering parameters. Compared with HfB₂-SiC ceramics, Hf_0.95V_0.05B₂-20 vol% SiC ceramics exhibited an elevated and comparable value of Vickers hardness (23.64 GPa), but lower fracture toughness (4.09 MPa m^1/2).     

Effects of (Ta0.2W0.2Nb0.2Mo0.2V0.2)C high-entropy carbide content on the microstructure and properties of Ti(C0.7N0.3)-based cermet

Using pre-synthesized high-entropy (Ta_0.2W_0.2Nb_0.2Mo_0.2V_0.2)C carbide as the reinforcing phase, Ti(C_0.7N_0.3)-based cermets were prepared by pressureless sintering at 1600 °C. The results revealed that due to the solid solution reaction between the mono-carbide and (Ta_0.2W_0.2Nb_0.2Mo_0.2V_0.2)C, only one set of face-centered-cubic diffraction peaks in XRD was detected in the as-sintered cermets, alongside the typical core-rim structure. Compared to the Ti(C_0.7N_0.3)-based cermets without high-entropy reinforcing phase, the Vickers hardness was increased from 17.06 ± 0.09 GPa to 18.42 ± 0.33 GPa and the fracture toughness was increased from 9.21 ± 0.31 MPa m^1/2 to 12.56 ± 0.23 MPa m^1/2 by adding 10 wt% (Ta_0.2W_0.2Nb_0.2Mo_0.2V_0.2)C. The wear resistance of the cermet was enhanced significantly with increasing (Ta_0.2W_0.2Nb_0.2Mo_0.2V_0.2)C content. This work provided a potential that the high-entropy carbide can be applied as an effective reinforcing phase in the preparation of high-performance Ti(C_0.7N_0.3)-based cermets.     

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase

The relationships between microstructures and mechanical properties especially strength and toughness of high-entropy carbide based ceramics are reported in this article. Dense (Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C (HEC) and its composite containing 20 vol.% SiC (HEC-20SiC) were prepared by spark plasma sintering. The addition of SiC phase enhanced the densification process, resulting in the promotion of the formation of the single-phase high-entropy carbide during sintering. The high-entropy carbide phase demonstrated a fast grain coarsening but SiC particles remarkably inhibited this phenomena. Dense HEC and HEC-20SiC ceramics sintered at 1900 °C exhibits four-point bending strength of 332 ± 24 MPa and 554 ± 73 MPa, and fracture toughness of 4.51 ± 0.61 MPa·m^1/2 and 5.24 ± 0.41 MPa·m^1/2, respectively. The main toughening mechanism is considered to be crack deflection by the SiC particles.     

Pressureless densification,microstructure tailoring and properties of Ta0.8Hf0.2C-based composites

Ta_0.8Hf_0.2C (TH) ceramics are desirable for applications in ultra-high temperature environments, but they are difficult to be sintered pressurelessly. TH ceramics were densified up to 98.8% from commercial powders via pressureless sintering (PLS) at 2473 K. SiC was introduced as secondary phase to tailor microstructures and improve properties of TH. The influence of SiC volume fraction on the densification, microstructure evolution and room-temperature properties of TH-based ceramics were examined. Average grain size of TH was refined from 13.6 down to 2.0 μm. 10 vol% SiC addition contributed to densification of Ta_0.8Hf_0.2C-SiC (THS) composites with a relative density of 99.6%. The mechanical properties of THS were fairly good, and thermal properties of sintered THS displayed a remarkable improvement compared with TH: the coefficient of thermal expansion (CTE) showed a reduction of 8.6% while the thermal conductivity increased from 18.6 to 41.5 W/m K.     

Synthesis,microstructure and mechanical properties of Cr2AlC/Al2O3 in situ composites by reactive hot pressing

Al₂O₃ particle-reinforced Cr₂AlC in situ composites were successfully fabricated from powder mixtures of Cr₃C₂, Cr, Al, and Cr₂O₃ by a reactive hot-pressing method at 1400 °C. A possible synthesis mechanism was proposed to explain the formation of the composites in which Al₂O₃ was formed by the aluminothermic reaction between Al and Cr₂O₃, meanwhile, Cr₃C₂, Al, together with Cr reacted to form Cr₂AlC in a shortened reaction route. The effect of Al₂O₃ addition on the microstructure and mechanical properties of Cr₂AlC/Al₂O₃ composites was investigated. The results indicated that the as-sintered products consisted of Cr₂AlC matrix and Al₂O₃ reinforcement, and the in situ formed fine Al₂O₃ particles dispersed at the matrix grain boundaries. The flexural strength and Vickers hardness of the composites increased gradually with increasing Al₂O₃ content. But the fracture toughness peaked at 6.0 MPa m^1/2 when the Al₂O₃ content reached 11 vol.%. The strengthening and toughening mechanism was also discussed.     

Medium-entropy (Ti,Zr, Hf)2SC MAX phase

Medium- and high-entropy alloys or ceramics for tuning the physicochemical properties of materials by the combination of multiple principal elements have received much interest. Herein, a medium-entropy (Ti, Zr, Hf)₂SC phase was synthesized attributing to the structural and chemical diversity of MAX phases. The crystal structure of (Ti, Zr, Hf)₂SC was determined by the Rietveld refinement of XRD, SEM, and atom-resolved TEM along with EDS elemental analysis. Phase evolution of X-ray diffraction patterns and TG/DSC curves were employed to reveal the synthesis mechanism of (Ti, Zr, Hf)₂SC from 2TiC–Zr–ZrC-2HfH₂-3.2FeS reactant system. The Vicker's hardness and the electrical resistivity of (Ti, Zr, Hf)₂SC were found higher than those of Ti₂SC, but the thermal conductivity of (Ti, Zr, Hf)₂SC was lower.     

Optimized mechanical properties and oxidation resistance of low carbon Al2O3-C refractories through Ti3AlC2 addition

The mechanical properties and oxidation resistance of the Al₂O₃-C refractories are of critical importance for iron and steel making processes. However, the evaporation of antioxidants related phases such as Al(g), Si(g), and SiO(g) would deteriorate these properties, especially during high-temperature treatment/application. Therefore, in the present work, a small amount of Ti₃AlC₂ compared with Al was introduced to overcome these problems. The phase compositions, microstructures, mechanical properties, and oxidation resistance of Ti₃AlC₂ containing refractories were investigated. The partial oxidation of Ti₃AlC₂ led to inherited lamellar structures such as Ti₃Al_1-xC₂, TiC, and granular Al₂TiO₅ phases. The controlled oxidation of Ti₃AlC₂ and its volume expansion contributed to the compact-structure, thereby limiting the escape of Si and SiO vapors at high temperatures. Consequently, the mechanical properties and oxidation resistance of Ti₃AlC₂ containing Al₂O₃-C refractories treated at 1600 ℃ were improved.