High-performance flexible supercapacitors based on C/Na<Subscript>2</Subscript>Ti<Subscript>5</Subscript>O<Subscript>11</Subscript> nanocomposite electrode materials

A new solution method to synthesize Na₂Ti₅O₁₁ with titanium powder is presented, and the C/Na₂Ti₅O₁₁ nanocomposite with high specific surface area and tunnel structure as the electrode material has excellent electrochemical performance. The single electrode composed of the C/Na₂Ti₅O₁₁ nanocomposite based on carbon fiber fabric (CFF) has the highest area capacitance of 1066 mF cm^?2 at a current density of 2 mA cm^?2, which is superior to other titanates and Na-ion materials for supercapacitors (SCs). By scan-rate dependence cyclic voltammetry analysis, the capacity value shows both capacitive and faradaic intercalation processes, and the intercalation process contributed 81.7% of the total charge storage at the scan rate of 5 mV s^?1. The flexible symmetric solid-state SCs (C/Na₂Ti₅O₁₁/CFF//C/Na₂Ti₅O₁₁/CFF) based on different C/Na₂Ti₅O₁₁ mass were fabricated, and 7 mg SCs show the best supercapacitive characteristics with an area capacitance of 309 mF cm^?2 and a specific capacitance of 441 F g^?1, it has a maximum energy density of 22 Wh kg^?1 and power density of 1286 W kg^?1. As for practical application, three SCs in series can power 100 green light-emitting diodes (LEDs) to light up for 18 min, which is much longer than our previous work by Wang et al. lighting 100 LEDs for 8 min. Thus, the C/Na₂Ti₅O₁₁ nanocomposite has promising potential application in energy storage devices.     

Facile synthesis of graphene@NiMoO<Subscript>4</Subscript> nanosheet arrays on Ni foam for a high-performance asymmetric supercapacitor

Honeycomb-like NiMoO₄ with nanosheet arrays is grown on reduced graphene oxide, which is supported on Ni foam having successfully fabricated by a simple hydrothermal treatment followed by a calcined process. In the as-synthesized Ni foam@reduced graphene oxide@NiMoO₄, Ni foam served as “skeleton” to support reduced graphene oxide and reduced graphene oxide directly grown on Ni foam served as the “skin” to provide high passway of electrons and ions, which simultaneously accommodated the volume change during the process of charge–discharge and NiMoO₄ acted as active substance to provide high areal capacitance. It shows a high areal capacitance of 2165.9 mF cm^?2 at a current density of 1 mA cm^?2 and long cycle stability with 93.8% capacitance retained over 1000 charge–discharge cycles. Moreover, an asymmetric supercapacitor has been constructed by using Ni foam@reduced graphene oxide and Ni foam@reduced graphene oxide@NiMoO₄ as negative and positive electrodes. The energy density of this asymmetric supercapacitor is 0.579 mWh cm^?2, and it retains 93.1% capacitance over charge–discharge 5000 cycles. Therefore, it reveals great promise for practical applications in energy storage devices.     

Samarium-doped Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles with improved magnetic and supercapacitive performance: a novel preparation strategy and characterization

Sm³⁺-doped magnetite (Fe₃O₄) nanoparticles were synthesized through a one-pot facile electrochemical method. In this method, products were electrodeposited on a stainless steel (316L) cathode from an additive-free 0.005 M Fe(NO₃)₃/FeCl₂/SmCl₃ aqueous electrolyte. The structural characterizations through X-ray diffraction, field-emission electron microscopy, and energy-dispersive X-ray indicated that the deposited material has Sm³⁺-doped magnetite particles with average size of 20 nm. Magnetic analysis by VSM revealed the superparamagnetic nature of the prepared nanoparticles (Ms = 41.89 emu g^?1, Mr = 0.12 emu g^?1, and H _Ci = 2.24 G). The supercapacitive capability evaluation of the prepared magnetite nanoparticles through cyclic voltammetry and galvanostat charge–discharge showed that these materials are capable to deliver specific capacitances as high as 207 F g^?1 (at 0.5 A g^?1) and 145 F g^?1 (at 2 A g^?1), and capacity retentions of 94.5 and 84.6% after 2000 cycling at 0.5 and 1 A g^?1, respectively. The results proved the suitability of the electrosynthesized nanoparticles for use in supercapacitors. Furthermore, this work provides a facile electrochemical route for the synthesis of lanthanide-doped magnetite nanoparticles.     

Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods with secondary plate-like nanostructures; preparation,characterization and application as high performance electrode material in supercapacitors

Mn₃O₄ nanorods with secondary plate-like structures were prepared through precipitation from a 0.005 M manganese chloride bath, under the applying direct current mode (i = 2 mA cm^?2). The structural analysis through XRD and FTIR confirmed that the deposited nanopowder has pure monoclinic phase of Mn₃O₄. Further morphological assessment through SEM proved the product to have the Mn₃O₄ nanorods in large quantity, which constructed the secondary plate-like building blocks. Cyclic voltammetric and charge–discharge experiments on the product indicated the prepared Mn₃O₄ to possess high specific capacitance (SC) values of 298 F g^?1, as well as an outstandingly durable cycling stability (95.1 % of initial capacity after discharging 1000 cycles).     

Investigation for the synthesis of hierarchical Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@MnO<Subscript>2</Subscript> nanoarrays materials and their application for supercapacitor

We designed and fabricated hierarchical Co₃O₄@MnO₂ nanoarrays directly grown on nickel foam by hydrothermal and calcination methods. After the investigation of growth mechanism, we found that the deposition of MnO₂ was based on the self-decomposition of KMnO₄ and the reducibility of Co₃O₄ during the hydrothermal process. Thanks to the hierarchical structure, the obtained electrode exhibited excellent capacitive performance in supercapacitor. It delivered 21.72 F cm^?2 at a current density of 5 mA cm^?2 and retained ~94 % capacitance of initial value after 5000 cycles.     

Improvement of hydrothermally synthesized MnO2 electrodes on Ni foams via facile annealing for supercapacitor applications

Nanostructured manganese dioxide (MnO₂) is deposited on nickel foams by a hydrothermal synthesis route. As-deposited MnO₂ thin films are largely amorphous. Facile post-deposition annealing significantly improves the electrochemical performance of the MnO₂ thin films via changing their morphology, phase, and crystallinity. The specific capacitance of the MnO₂ electrode increases with the annealing temperature and reaches an optimal value of 244 F g^?1 (at the current density of 1 A g^?1) in a neutral 1 M Na₂SO₄ electrolyte for a specimen annealed at 500 °C. Furthermore, when an alkaline 5 M KOH electrolyte is used, an exceptionally high capacitance of 950 F g^?1 is achieved at the current density of 2 A g^?1. The cost-effective facile synthesis, high specific capacitance, and good cycle stability of these MnO₂-based electrodes enable their applications in high-performance supercapacitors.     

The synthesis and characterization of Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> thin films from melt reactions using xanthate precursors

Kesterite, Cu₂ZnSnS₄ (CZTS), is a promising absorber layer for use in photovoltaic cells. We report the use of copper, zinc and tin xanthates in melt reactions to produce Cu₂ZnSnS₄ (CZTS) thin films. The phase of the as-produced CZTS is dependent on decomposition temperature. X-ray diffraction patterns and Raman spectra show that films annealed between 375 and 475 °C are tetragonal, while at temperatures <375 °C hexagonal material was obtained. The electrical parameters of the CZTS films have also been determined. The conduction of all films was p-type, while the other parameters differ for the hexagonal and tetragonal materials: resistivity (27.1 vs 1.23 Ω cm), carrier concentration (2.65 × 10⁺¹⁵ vs 4.55 × 10⁺¹⁷ cm^?3) and mobility (87.1 vs 11.1 cm² V^?1 s^?1). The Hall coefficients were 2.36 × 10³ versus 13.7 cm³ C^?1.     

Controllable Synthesis of Atomically Thin Type‐II Weyl Semimetal WTe2 Nanosheets: An Advanced Electrode Material for All‐Solid‐State Flexible Supercapacitors

Compared with 2D S‐based and Se‐based transition metal dichalcogenides (TMDs), Te‐based TMDs display much better electrical conductivities, which will be beneficial to enhance the capacitances in supercapacitors. However, to date, the reports about the applications of Te‐based TMDs in supercapacitors are quite rare. Herein, the first supercapacitor example of the Te‐based TMD is reported: the type‐II Weyl semimetal 1Td WTe₂. It is demonstrated that single crystals of 1Td WTe₂ can be exfoliated into the nanosheets with 2–7 layers by liquid‐phase exfoliation, which are assembled into air‐stable films and further all‐solid‐state flexible supercapacitors. The resulting supercapacitors deliver a mass capacitance of 221 F g^?1 and a stack capacitance of 74 F cm^?3. Furthermore, they also show excellent volumetric energy and power densities of 0.01 Wh cm^?3 and 83.6 W cm^?3, respectively, superior to the commercial 4V/500 µAh Li thin‐film battery and the commercial 3V/300 µAh Al electrolytic capacitor, in association with outstanding mechanical flexibility and superior cycling stability (capacitance retention of ≈91% after 5500 cycles). These results indicate that the 1Td WTe₂ nanosheet is a promising flexible electrode material for high‐performance energy storage devices.     

Effect of excess Bi content on electrical properties of BiFe<Subscript>0.95</Subscript>Cr<Subscript>0.05</Subscript>O<Subscript>3</Subscript> thin films

The Bi_1?+?xFe_0.95Cr_0.05O₃ (BFCO) (x?=?0, 5, 10, 15 and 20%) thin films are fabricated on FTO/glass substrate using a chemical solution deposition method and sequential-layer annealing process. The effects of the excess Bi content on crystalline structure, morphology, and electrical performance of BFCO thin films are investigated. All the BFCO thin films are crystallized into polycrystalline perovskite structure and belonging to the space group of R3c. The BFCO thin films with 5 and 10% excess Bi contents possess no impurity phase. Especially, a dense surface morphology and columnar crystal structure can be obtained for the film with 5% excess Bi content. Especially, the one possesses superior ferroelectricity with a relative high remnant polarization (P _r) of 69.8 µC/cm² and low coercive electric field (E _c) of 291 kV/cm at 1 kHz due to the relatively low leakage current density of 3.04?×?10^??5 A/cm² at 200 kV/cm.     

Successful synthesis of interconnected Co<Subscript>0.85</Subscript>Se nanosheets with high pore volume and its electrochemical performance in supercapacitors

Interconnected Co_0.85Se nanosheets have been prepared by a facile hydrothermal method via tuning reaction time to control the chemical constitution and the morphology. The nanosheets morphology of Co_0.85Se offers sufficient electron transfer and short ion diffusion pathway, which can favor the fast transfer of electrolyte ions. The Co_0.85Se electrode exhibits specific capacitance of 980 F g^??1 at 10 A g^??1 with high cycling life stability (8.3% loss after 5000 cycles) and good conductivity. The assembled Co_0.85Se//AC asymmetric supercapacitor (ASC) device exhibits a high energy density of 46.2 Wh kg^??1 at a power density of 807.4 W kg^??1 and still maintained 29.3 Wh kg^??1 at a power density of 15981.8 W kg^??1 with excellent cycling performance (90.01% capacitance retention over 5000 cycles). The impressive results indicate that such unique interconnected Co_0.85Se nanosheets are promising electrode materials for high-performance supercapacitors.     

Cathodic electrosynthesis of CuFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/CuO composite nanostructures for high performance supercapacitor applications

In this work, CuFe₂O₄/CuO nanocomposites have been synthesized by galvanostatic cathodic electrodeposition. The obtained nanocomposites were characterized by field emission scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, Fourier Transform Infrared, and Brunauer–Emmett–Teller surface area analysis. The electrochemical properties of CuFe₂O₄/CuO nanocomposites were evaluated by cyclic voltammetry, galvanostatic charge–discharge cycling, and electrochemical impedance spectroscopy in 1.0 M KOH. The CuFe₂O₄/CuO nanocomposites have shown the high specific capacitance of 322.49 F g^?1 at the scan rate of 1 mV s^?1. After 5000 cycles, 92% of this specific capacitance was retained. Although the prepared nanocomposite has shown a mediocre specific capacitance compared to other metal oxide-based materials, the low cost of the starting materials and the ease of preparation make this nanocomposite a good candidate for supercapacitor applications.     

Synthesis and characterization of nanocrystalline TiO<Subscript>2</Subscript> thin films

Nanocrystalline thin films of TiO₂ have been synthesized by sol gel spin coating technique Thin films of TiO₂ annealed at 700 °C were characterized by X-ray diffraction(XRD), Atomic Force Microscopy, High resolution TEM and Scanning Electron Microscopy (SEM), The XRD shows formation of tetragonal anatase and rutile phases with lattice parameters a = 3.7837 Å and c = 9.5087 Å. The surface morphology of the TiO₂ films showed that the nanoparticles are fine with an average grain size of about 60 nm. Optical studies revealed a high absorption coefficient (10⁴ cm^?1) with a direct band gap of 3.24 eV. The films are of the n type conduction with room temperature electrical conductivity of 10^?6 (Ω cm)^?1.     

Preparation and electrochemical properties of nanorods and nanosheets structural Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> as anode for lithium ion batteries

In this study, nanorods and nanosheets structure of Li₄Ti₅O₁₂ (LTO) with higher capacity and cycle performance are prepared by hydrothermal synthesis. We can obtain different nanostructural LTO by changing heating time in autoclave and molar ratio between lithium (Li) and titanium (Ti). Precursor was calcined at 600 °C for 6 h in air after heating to 180 °C with the holding time of 12 and 24 h in Teflon-lined PTFE autoclave vessel, nanorods and nanosheets structure of LTO were prepared successfully, respectively. Specially, when the molar ratio between Li and Ti was 4.2:5, the discharge capacities were 177.7 and 230.7 mAh g^?1 at 20 mA g^?1, respectively. When the holding time was 24 h as well as molar ratio between Li and Ti was 4.2:5, the band gap was least, and this pure LTO reversible capacities reached 90.36 and 73.12% after 200 and 3000 cycles at 100 mA g^?1 and 1 A g^?1, respectively.     

Electrochemical preparation and energy storage properties of nanoporous Co(OH)<Subscript>2</Subscript> via pulse current deposition

Nanoporous Co(OH)₂ films are electrochemically deposited on Ni foams by pulse current deposition for supercapacitor application. The pore size and density are controlled by reaction conditions including frequency modulation and reaction time. The morphology of the films is monitored by SEM, and the chemical composition and crystal structure are confirmed by XPS and XRD, respectively. The electrochemical performance of the Co(OH)₂ film is characterized by cyclic voltammetry and charge–discharge tests. The charge-transfer resistances of the electrodes are examined by electrochemical impedance spectroscopy. The Co(OH)₂ film exhibits an excellent specific capacity of 1681 F g^?1 at a current density of 2 A g^?1 in a potential range of ?0.1 to 0.4 V from the charge/discharge test; this specific capacity is much higher than that obtained by direct current deposition (623 F g^?1 at the same condition) due to the highly porous structure.     

Ordered mesoporous carbon-supported CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> composite with enhanced lithium storage properties

A high and stable reversible specific capacity (1277.7 mAh g^?1) was successfully achieved by the CoFe₂O₄/ordered mesoporous carbon nanohybrids (CFO/CMK-3) composite anode at the current density of 0.1 A g^?1 after 100 cycles. CFO/CMK-3 electrode also exhibited a stable capacity up to 733.2 and 482.6 mAh g^?1 at the current densities of 0.5 and 1 A g^?1 after 500 cycles, respectively. The CFO particles were found to be uniformly distributed inside the pore channels of CMK-3. Structure characterization before and after 100 tests revealed that the specific CMK-3 mesoporous structure and CFO crystallites remained unchanged. The stability of the anode composite stability and the rapid redox capability of CFO gave rise to superior lithium storage capacity and excellent cycling stability. CFO/CMK-3 showed a great promise to serve as anode for high-performance lithium-ion battery.     

Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles embedded in 3D reduced graphene oxide network as anode for high-performance lithium ion batteries

Mn₃O₄ nanoparticles were in-situ synthesized in the 3D framework of reduced graphene oxide (RGO) by a facile one-step hydrothermal method. In the reduced graphene-Mn₃O₄ (RGM) composite, the RGO network not only serves as a mechanical support to construct a self-supported and binder-free electrode, but also offers 3D continuous conductive network for effective electron transfer. The Mn₃O₄ nanoparticles anchored uniformly across the RGO framework, which provided high capacity and prevented the restacking of the RGO thin sheets. Based on the unique composite structures, strong synergistic effect was achieved between Mn₃O₄ and RGO, resulting in superior specific capacity, enhanced rate capability, stable cycling performance and nearly 100% Coulombic efficiency in the RGM2 composites. With an optimal Mn₃O₄ composition of 44% by weight (similarly hereinafter), the composite exhibits high specific capacities of 696–795 mAh g¹ based on the overall weight of the electrode in 60 cycles at 200 mA g^?1, with a large coulombic efficiency of around 98%. Even at a high current density of 10,000 mA g^?1, the composite can still deliver a capacity of 383 mAh g^?1, demonstrating its excellent rate performance. The outstanding performances of the composites are attributed to the synergistic effect of both components and the hierarchical structure of the composite.     

Achieving High Capacitance of Paper‐Like Graphene Films by Adsorbing Molecules from Hydrolyzed Polyimide

To date, graphene‐based electric double layer supercapacitors have not shown the remarkable specific capacitance as theoretically predicted. An efficient strategy toward boosting the overall capacitance is to endow graphene with pseudocapacitance. Herein, molecules of hydrolyzed polyimide (HPI) are used to functionalize N‐doped graphene (NG) via π–π interaction and the resulting enhanced electrochemical energy storage is reported. These aromatic molecules in monolayer form on graphene contribute strong pseudocapacitance. Paper‐like NG films with different areal mass loadings ranging from 0.5 to 4.8 mg cm^?2 are prepared for supercapacitor electrodes. It is shown that the gravimetric capacitance can be increased by 50–60% after the surface functionalization by HPI molecules. A high specific capacitance of 553 F g^?1 at 5 mV s^?1 is achieved by the HPI‐NG film with a graphene mass loading of 0.5 mg cm^?2 in H₂SO₄ aqueous electrolyte. For the HPI‐NG film with highest mass loading, the gravimetric specific capacitance drops to 340 F g^?1 while the areal specific capacitance reaches a high value of 1.7 F cm^?2. HPI‐NG films are also tested in Li₂SO₄ aqueous electrolyte, over an extended voltage window of 1.6 V. High specific energy densities up to 40 Wh kg^?1 are achieved with the Li₂SO₄ electrolyte.     

Template-free synthesis of Ni<Subscript>2</Subscript>P hollow microspheres with great photocatalytic and electrochemical properties

The hollow Ni₂P microspheres were prepared using a facile one-step template-free solvothermal method. The products were characterized and the results showed that they were pure hexagonal Ni₂P microspheres, made up of large amounts of Ni₂P nanoparticles, and had an obvious inner space in the central of the microspheres. After being investigated, it was found that these Ni₂P hollow spheres initially were some solid spheres, but after a specified time, they were converted to a hollow structure by an Ostwald ripening process, some even had a multi-wall hollow structure. Meanwhile, the as-prepared Ni₂P hollow spheres showed a good photocatalytic degradation performance for Methylene Blue in aqueous solution. Electrochemical measurements turned out that the Ni₂P hollow spheres have a great cycling performance. The initial discharge capacity capacity of is Ni₂P hollow spheres up to 660 mAh g^?1 and it always keep in about 300 mAh g^?1 within 100 cycles at the current density of 100 mA g^?1.     

Enhanced electrochemical performance of Na<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>F<Subscript>3</Subscript> for Na-ion batteries with nanostructure and carbon coating

Carbon-coating Na₃V₂(PO₄)₂F₃ nanoparticles (NVPF@C NP) were prepared by a hydrothermal assisted sol–gel method and applied as cathode materials for Na-ion batteries. The as-prepared nanocomposites were composed of Na₃V₂(PO₄)₂F₃ nanoparticles with a typical size of ~?100 nm and an amorphous carbon layer with the thickness of ~?5 nm. Cyclic voltammetry, rate and cycling, and electrochemical impedance spectroscopy tests were used to discuss the effect of carbon coating and nanostructure. Results display that the as-prepared NVPF@C NP demonstrates a higher rate capability and better long cycling performance compared with bare Na₃V₂(PO₄)₂F₃ bulk (72 mA h g^?1 at 10 C vs 39 mA h g^?1 at 10 and 1 C capacity retention of 95% vs 88% after 50 cycles). The remarking electrode performance was attributed to the combination of nanostructure and carbon coating, which can provide short Na-ion diffusion distance and rapid electron migration.     

A promising mechanical ball-milling method to synthesize carbon-coated Co<Subscript>9</Subscript>S<Subscript>8</Subscript> nanoparticles as high-performance electrode for supercapacitor

A Co₉S₈/C nanocomposite has been prepared using a solid-state reaction followed by a facile mechanical ball-milling treatment with sucrose as the carbon source. The phases, morphology, and detailed structures of Co₉S₈/C nanocomposite are well characterized by X-ray diffraction, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy. Our experimental results show that not only a process of particle size reduction, the ball-milling treatment also promotes the carbon and Co₉S₈ combining with each other more effectively to form an ultrafine nanocomposite. When used as an electrode material in supercapacitor, Co₉S₈/C nanocomposite exhibits a high initial specific capacitance of 756.2 F g^?1 at 1 A g^?1 and excellent cycling stability with 73.4% retention after 2000 cycles. Its outstanding electrochemical properties are mainly attributed to the nanosize of particles and amorphous carbon layer coating on its surface.