Synthesis and systematic investigations of Al and Cu-doped ZnO nanoparticles and its structural,optical and photo-catalytic properties

Here we report, copper (Cu) and Aluminum (Al) doped zinc oxide (ZnO) nanoparticles by a novel one step microwave irradiation method for the first time. Powder X-ray diffraction (XRD) reveals that both pure and doped samples assigned to hexagonal wurtzite type structure. The calculated average crystalline size decreases from 24 to 11 nm for pure and doped (Al and Cu) ZnO respectively, which is in good agreement with the particles size observed from Transmission Electron Microscope (TEM) analyses. A considerable red shift in the absorption edge and the reduction in the energy gap from 3.35 to 2.95 eV reveal the substitution of Al³⁺ and Cu²⁺ ions into the ZnO lattice analyzed by UV–Vis transmission spectra. The photocatalytic degradation of Methyl Violet (MV), Phenol and Rhodamine B (RHB) was investigated by using pure, Al and Cu doped ZnO catalyst under UV light irradiation. The results showed that the photocatalytic property is significantly improved by Cu doping concentration. This could be attributed to extended visible light absorption, inhibition of the electronehole pair’s recombination and enhanced adsorptivity of dye molecule on the surface of Cu–ZnO nanopowders. The samples were further characterized by photoluminescence spectra and Fourier Infrared Spectra (FTIR) analysis.     

Structural and optical properties of Ag doped tungsten oxide (WO<Subscript>3</Subscript>) by microwave-assisted chemical route

The present study explores, the pure and silver (Ag) doped WO₃ nanoparticles synthesized by microwave irradiation method. Powder X-ray diffraction results reveal that the WO₃ doped with Ag concentration from 0 to 10 wt% crystallizes in monoclinic structure. TEM analysis shows both pristine and silver doped WO₃ nanoparticles. They are having spherical morphology with a average size from 30 to 40 nm. Scanning electron microscopy studies depicts that both the pristine and Ag doped WO₃ form in spherical shaped morphology with an average diameter of 40–30 nm, which is in proper agreement with the average crystallite sizes calculated by Scherrer’s formula. A considerable red shift in the absorbing band edge and a decrease in the band gap energy from 3.00 to 2.85 eV for Ag doped samples were observed by using UV–DRS spectra analysis. The defects in crystal and oxygen deficiencies were analyzed by photoluminescence spectra analysis.     

Improved photodegradation activity of SnO<Subscript>2</Subscript> nanopowder against methyl orange dye through Ag doping

Silver doped tin oxide (SnO₂:Ag) nanopowders were synthesized by a simple soft chemical route with 0, 5, 10 and 15 wt% concentrations of Ag. The structural, morphological, optical, photoluminescence and photocatalytic properties of the synthesized samples were studied and the results obtained are reported in this paper. XRD studies confirm the polycrystalline nature of the synthesized samples. The undoped and doped samples exhibit a strong (1 0 1) preferential growth. Decreased crystallite size is observed with Ag doping. Nanosized grains were observed for the doped samples. Peak related to Sn–O–Sn lattice vibration is observed for both the undoped and doped samples in the FTIR spectra. Peaks related to oxygen vacancies were observed at 362 and 499 nm for all the samples in the PL spectra. Enhanced photocatalytic activity was observed for the doped samples and the SnO₂:Ag nanopowder with 10 wt% Ag doping concentration exhibited maximum photodegradation efficiency against the degradation of methyl orange dye.     

A selective ethanol gas sensor based on spray-derived Ag–ZnO thin films

A simple and cost-effective spray pyrolysis technique was employed to synthesize silver-doped zinc oxide (Ag–ZnO) thin films on the glass substrates from aqueous solutions of zinc acetate and silver nitrate precursors at 450 °C. The effects of Ag doping on structural, morphological, and gas-sensing properties of films were examined. The X-ray diffraction spectra of the Ag–ZnO films showed the polycrystalline nature having hexagonal crystal structure. Scanning electron microscopy (SEM) images of the pure ZnO films revealed the uniform distribution of the spherical grains (~80 nm size). Tiny Ag nanoparticles are clearly visualized in the SEM of Ag–ZnO films. The investigation of the effect of Ag doping on the gas-sensing properties of the Ag–ZnO revealed that the 15 % Ag-doped ZnO sample has the highest gas sensitivity (85 %) and excessive Ag doping in ZnO degraded the gas sensitivity. A possible mechanism of Ag–ZnO-based sensor sensitivity to the target gas is also proposed.     

Enhancement in the photocatalytic activity of Ag loaded N-doped TiO2 nanocomposite under sunlight

A N-doped titania–silver nanocomposites have been prepared by simple microwave assisted and impregnation–reduction method for the first time. As synthesized nanocomposites with different Ag contents were characterized for their phase purity, morphology, particle size, optical properties and elemental composition. It is found that N-doped TiO₂ silver nanocomposites are pure in anatase phase with an average crystallite size of 10 nm. The catalyst was tested for dye degradation and photodegradation efficiency was found to be 99.6 and 88.7 % within 90 min under UV and sunlight respectively. A 40 % enhancement in the photodegradation efficiency was achieved by Ag loading in comparison with the N-TiO₂ under sunlight. The fluorescence quenching of Ag loaded N-TiO₂ indicates decrease in rate of electron–hole pair recombination that enhances photocatalytic performance. The effects of photocatalytic operational parameters such as method of surface modification, catalyst loading and irradiation sources on the photodegradation of methyl orange were also investigated.     

Growth and characterization of flower-like Ag/ZnO heterostructure composites with enhanced photocatalytic performance

Flower-like Ag/ZnO heterostructure composites were prepared through a solvothermal method without surfactants or templates. The products were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy, and photoluminescence (PL) spectroscopy. Results demonstrate that flower-like Ag/ZnO heterostructure composites were composed of wurtzite ZnO flowers coated by face-center-cubic Ag nanoparticles. The growth process of flower-like ZnO crystals was investigated, and a possible growth mechanism was proposed. The photocatalytic activity of the as-prepared flower-like Ag/ZnO samples, pure ZnO samples, and commercial TiO₂ (Degussa, P-25) was tested with the photocatalytic degradation of methylene blue. Results show that the Ag/ZnO heterostructures were superior in photocatalytic activity to the pure ZnO samples and the commercial TiO₂ (Degussa, P-25), but the mixture of Ag (0.1 wt%) particles and ZnO flowers did not, which implies that the heterostructure promoted the separation of photogenerated electron–hole pairs, enhancing the photocatalytic activity. That was primarily verified by the PL results.     

Synthesis, structural and optical properties of Ni-doped ZnO micro-spheres

Ni doped ZnO nanoparticles were synthesized by a simple chemical method at low temperature with Ni:Zn atomic ratio from 0 to 5 %. The synthesis process is based on the hydrolysis of zinc acetate dihydrate and nickel acetate tetrahydrate followed by heat treatment at 65 °C under refluxing using methanol as a solvent. X-ray diffraction analysis reveals that the Ni-doped ZnO crystallizes in a wurtzite structure with crystal size of 4–11 nm. These nanocrystals self-aggregated themselves into hollow spheres of size of 600–170 nm. High resolution transmission electron microscopy image shows that each sphere is made up of numerous nanoparticles of average diameter 4 nm. The XRD patterns, Scanning electron microscopy and transmission electron microscopy micrographs of doping of Ni in ZnO are confirmed the formation of micro-spheres. Furthermore, the UV–vis. spectra and photoluminescence spectra of the Ni-doped ZnO nanoparticles were also investigated. The band gap of the nanoparticles can be tuned in the range of 3.55–3.36 eV by the use of the dopants. The observed red shift in the band gap from UV–visible analysis and near band edge UV emission with Ni doping may be considered to be related to the incorporation of Ni ions into the Zn site of the ZnO lattice.     

Facile synthesis of Ag/ZnO heterostructures assisted by UV irradiation: Highly photocatalytic property and enhanced photostability

We report a new method to synthesize Ag/ZnO heterostructures assisted by UV irradiation. The formation of Ag/ZnO heterostructures depends on photogenerated electrons produced by ZnO under UV light to reduce high valence silver. Functional property of the Ag/ZnO heterostructures is evaluated by photodegradation of methylene blue (MB) under UV illumination. Results of photodegradation tests reveal that the optimal photocatalytic activity of as-syntheszied samples is about 1.5 times higher than the pure ZnO synthesized in the same condition or commercial TiO₂ (P-25), showing the advantage of the unique structure in the Ag/ZnO heterostructure. Besides, due to the reduced activation of surface oxygen atom, photocatalytic activity of the photocatalysts has no evident decrease even after three recycles.     

Optimization of CdO nanoparticles by Zr<Superscript>4+</Superscript> doping for better photocatalytic activity

Chemically controlled co-precipitation method has been adopted for the fabrication of pure and different wt% Zr doped CdO photocatalysts. Conventionally, the crystallite size and crystalline phase of CdO are in the midst of the parameters involved in the control of the photocatalytic activity. Aiming utterly at the size effect that modifies other attributes which are important to assess the photocatalytic activity of nanometric CdO, it was explored to synthesize CdO nanoparticles with controlled size, highly comparable morphology and analogous phase. The crystal structure and the crystallite size were estimated from the X-ray diffraction patterns and were confirmed through transmission electron microscope. The degree of crystallinity varied on Zr doping and the calculated crystallite sizes were in the range of 16–81 nm. The dopant ion Zr⁴⁺ have been detected through X-ray photoelectron spectroscopy (XPS) analysis signifying the dopant to substitute for cadmium (Cd²⁺) in the lattice of CdO. Particle size dependent optical band gaps calculated in the range 2.02–2.57 eV informed the viability of the materials to initiate photocatalytic reaction in the visible light region. Lesser recombination rate of the generated electrons and holes under light irradiation produced low intense photoluminescence peaks that displayed the appropriateness as photocatalysts. Zr⁴⁺ doping resulted in the enhancement of photocatalytic activity, evaluated by monitoring the degradation of methylene blue solution. 0.5 wt% Zr doped CdO nanoarticles calcined at 400 °C exhibited the highest photocatalytic activity with better percentage of color abatement (80.95%). The pseudo-first-order reaction rate became faster on Zr doping such that the rate constant is ~?0.4–0.5 h^?1 for Zr doped CdO while that for pure CdO is ~?0.3 h^?1.     

Structural and optoelectronic characterization of prepared and Sb doped ZnO nanoparticles

This paper briefly reports the structural and optoelectronics properties of prepared pure and Sb doped ZnO nanoparticles. Doping with suitable elements offers an efficient method to control and enhance the optical properties of ZnO nanoparticles, which is essential for various optoelectronics applications. Sb doped ZnO nanoparticles have significant concern due to their unique and unusual electrical and optical properties. In the present work, we report the synthesis of Sb doped ZnO successfully with average particle size range from 26 to 29 nm via direct precipitation method. The phase purity and crystallite size of synthesized ZnO and Sb doped nano-sized particles were characterized and examined via X-ray diffraction (XRD) and scanning electron microscopy (SEM). The elemental analyses of undoped and doped ZnO nanoparticles were examined by using energy-dispersive X-ray spectroscopy (EDAX).We investigated and measured the optoelectronics properties of synthesized ZnO and Sb doped ZnO nanoparticles by employing photoluminescence and UV–Visible spectroscopy. The influence of Sb doping on photoluminescence (PL) spectra of ZnO nanoparticles, which consists of UV emission and broad visible emission band, is found to be strongly dependent upon the Sb concentration for all the Sb doped ZnO nanoparticles samples under investigation. The UV–Visible absorption study shows an increase in band gap energy as Sb is incorporated on the ZnO nanoparticles.     

Effect of Sn doping on microstructural and optical properties of ZnO nanoparticles synthesized by microwave irradiation method

Pure and Sn-doped ZnO nanostructures have been synthesized by the microwave irradiation method. The influence of Sn loading on the morphology and microstructure was evaluated by using field emission scanning electron microscopy, transmission electron microscopy (TEM), energy-dispersive spectrum analysis techniques, X-ray diffraction, and Fourier transform infrared spectroscopy. A change in the growth pattern, from needle-like particles for pure ZnO to agglomerated spherical crystallites for Sn-doped ZnO, has been observed. TEM observations indicated that the average particle size of the pure ZnO nano needles is in the range of 40–60 nm, whereas on addition of Sn spherical nanoassemblies size lies in the range of 10–21 nm. The pure ZnO and Sn-doped ZnO nanostructures were further characterized for their optical properties by UV–Vis reflectance spectra (DRS) and photoluminescence (PL) spectroscopy.     

Low temperature produced calcium-doped zinc oxide thick film via screen printing technique as thermal interface material in LED application

Pure and calcium-doped zinc oxide thick films were deposited on Aluminium substrate by screen printing technique using nanocrystalline powder synthesized from co-precipitation method. Shear thinning phenomenon with increment of shear rate was observed during the rheological analysis for all pastes. X-ray diffraction results confirmed the formation of ZnO with preferred orientation along (101) plane. Peak shifting to lower angle was observed upon increment of doping concentration of calcium. Crystallite size of doped ZnO powder decreased in the range (from 35.4 to 42.4 nm) from 116.1 nm of pure ZnO. Surface morphology analysed by FESEM had revealed the reduction of voids with increasing doping concentration up to 7 wt% of doping, followed by a slightly increase in the number of voids at 9 wt% doping. AFM analysis showed that the surface roughness of films exhibited a decreasing trend with the increase of calcium dopant until 7 wt% but became rougher at 9 wt%. Peaks shifting of ZnO to lower wavenumber revealed by FTIR study indicated that doping had affected the lattice structure of ZnO in the films. Thermal characterization showed the introduction of calcium dopant had increased the thermal resistance of the thick films. This led to a better junction temperature (T_j) of LED of 46.4?°C when compared with T_j of pure ZnO film at 47.3?°C.     

Ag~+掺杂FeVO_4光催化剂的制备及光催化性能

采用液相沉淀法制备了银(Ag+)掺杂钒酸铁(FeVO4)光催化剂。采用XRD、SEM、EDS、BET和XPS等手段对样品的性能进行了表征分析,并以甲基橙为目标降解物,考察了催化剂在节能灯照射下的光催化活性。结果表明,Ag的掺杂没有改变FeVO4晶型,但引起了晶格畸变和膨胀。适量Ag的掺杂可提高FeVO4的光催化性能,在所进行实验的条件下,钒酸银最佳掺杂量为1%(质量分数)时,掺杂后的Fe-VO4对甲基橙溶液的脱色率较未掺杂前提高21%左右。     

Sol–gel derived Ag-doped ZnO thin film for UV photodetector with enhanced response

Ultraviolet (UV) photodetectors based on pure zinc oxide (ZnO) and Ag-doped ZnO (Ag:ZnO) thin films with different Ag doping contents (0.05, 0.15, 0.65, 1.30 and 2.20 %) have been prepared by sol–gel technique. Photoresponse characteristics of the prepared detectors have been studied for UV radiation of λ = 365 nm and intensity = 24 μW/cm². The Ag:ZnO thin film-based photodetector having an optimum amount of 0.15 at. wt% Ag dopant exhibits a high photoconductive gain (K = 1.32 × 10³) with relatively fast recovery (T _37 % = 600 ms) and minimal persistence in comparison to other prepared photodetectors. The incorporation of Ag dopant (≤0.15 %) at Zn lattice sites (Ag_zn) in ZnO creates acceptor levels in the forbidden gap, thereby reducing the value of dark current. Upon illumination with UV radiation, the photogenerated holes recombine with the captured electrons at the Ag_zn sites. The photogenerated electrons increase the concentration of conduction electrons, thereby giving an enhanced photoresponse for Ag:ZnO photodetector (0.15 % Ag). At higher dopant concentration (≥0.65 %), Ag incorporated at the interstitial sites of ZnO leads to the formation of deep energy levels below the conduction band along with increase in oxygen-related defects, thereby giving higher values of dark current. The incorporation of Ag at interstitial sites results in degradation of photoresponse along with the appearance of persistence in recovery of the photodetector in the absence of UV radiation.     

Effect of leavening agent on structural and photocatalytic properties of ZnO nanorods

In the present work, we have demonstrated a simple, facile, one-step, rapid and cost effective synthesis of ZnO nanorods through the thermal decomposition of zinc acetate and leavening agent (NaHCO₃). The silver nanoparticles (AgNPs) were deposited on the surface of ZnO nanorods by photocatalytic reduction of Ag (I) to Ag(0). As synthesized ZnO nanorods and Ag–ZnO nanocomposites were characterized by using X-ray Diffraction, field emission scanning electron microscope, high-resolution transmission electron microscope and diffuse reflectance spectroscopy. The photocatalytic activities of the ZnO nanorods and Ag–ZnO nanocomposites were evaluated for the photodegradation of Methyl Orange (MO) under UV and sunlight irradiation. The use of common leavening agent helps to prevent the aggregation of ZnO nanorods, further it hinders crystallite growth and narrowing the diameter of nanorods by the evolution of carbon dioxide during calcination. The ZnO nanorods and Ag–ZnO nanocomposite exhibited an enhanced photocatalytic activity and separation of photogenerated electron and hole pairs. Due to effect of leavening agent and AgNPs deposited on surface of ZnO nanorods finds best catalyst for the 99% degradation of MO within 30 min compared to ZnO.     

Structure–property correlation of pure and Sn-doped ZnO nanocrystalline materials prepared by co-precipitation

The structural, optical and electrical properties of pure and tin (Sn) doped zinc oxide (ZnO) nanocrystalline materials prepared by co-precipitation method have been studied as a function of Sn doping concentration. The phase identification through powder X-ray diffraction methods confirmed that pure and Sn-doped zinc oxide powder have typical hexagonal wurtzite structure (a = 3.407 Å and c = 4.592 Å) with slight change in lattice parameters. The surface morphological examination with field emission scanning electron microscopy revealed the fact that the grains are closely and densely packed and pores/voids between the grains decrease with increasing the doping concentration of Sn from 0% to 15%. The energy bandgap of pure ZnO was found to be 3.35 eV from optical absorption spectra obtained by ultraviolet–visible (UV–Vis) absorption spectrophotometer. The variation of energy bandgap and electrical resistivity of Sn-doped ZnO were also determined with tin doping. Upon increasing the Sn dopant concentration from 0 to 15 wt%, the optical bandgaps of ZnO increases from 3.35 to 3.42 eV. The electrical resistivity of Sn-doped ZnO has been decreased at least two orders of magnitude, i.e. from 1263.17 to 28.64 Ω cm. This decrement in electrical resistivity may be due to the partial substitution of divalent Zn²⁺ ions with tetravalent Sn⁴⁺ ions, generating more free electrons for conduction.     

Enhanced the structure and optical properties for ZnO/PVP nanofibers fabricated via electrospinning technique

Zinc oxide/polyvinylpyrrolidone (ZnO/PVP) nanocomposite fibers with enhanced structural, morphological and optical properties were purposefully tailored using electrospinning technique. Meanwhile, ZnO nanoparticles (NPs),with particle size of ~50 nm, were synthesized using a co-precipitation method. The nanocomposite fibers were prepared by an electrospun solution of PVP containing ZnO NPs of 2, 4, 6 and 8 wt%. Evidently, the morphological, thermal and optical properties of the ZnO/PVP nanocomposite fibers were enhanced by dispersing ZnO NPs into PVP fibers. Typically, controlling the ZnO NPs content and their dispersibility (0–8 wt%) into PVP fibers result in improved the thermal stability (an increase of onset decomposition temperature by ~120 °C above pure PVP fibers) as well as the UV–Vis protection (reduction in UV transmission by 70%) and the photoluminescence properties (a sharp UV emission around 380 nm) Overall, based on the enhanced properties, the PVP/ZnO nanocomposite fibers can be considered a promise material in optoelectronic sensors and UV photoconductor.     

Clew-like hierarchical ZnO nanostructure assembled by nanosheets as an efficient photocatalyst for degradation of azure B

In this study, hierarchical ZnO nanostructure assembled by nanosheets was synthesized via a facile and rapid ultrasound assisted route without any surfactant or template. The phase structure, morphology and optical property of the ZnO sample were investigated by XRD, FT-IR, SEM, and UV–Vis spectroscopy. Nitrogen sorption was also studied to determine the specific surface area and the pore size distribution. The ZnO sample was hexagonal pure phase of hierarchical clew-like microspheres consisting of nanosheets with average thickness and specific surface area of 50 nm and 41 m² g^?1, respectively. Synthesized ZnO was applied for the photocatalytic degradation of an organic dye, azure B as a pollutant model under UV irradiation. The effects of several parameters including dye concentration, catalyst dosage, pH, and irradiation time on photocatalytic degradation have been studied. The results indicated hierarchical ZnO has potential application for degrading of organic pollutants. Hydroxyl radicals were found to be main reactive species in this photodegradation process.     

不同合成过程对溶胶-凝胶法制备的ZnO/Ag纳米复合材料光催化性能的影响

以乙酸锌、硝酸银为前驱体,二乙醇胺作为稳定剂,利用溶胶-凝胶法分别采用一步法和两步法制备得到ZnO以及ZnO/Ag纳米复合粉体。所有ZnO/Ag复合物中Ag的含量均为3%(摩尔分数)。对所制备样品的结构和光学性质通过XRD、SEM、TEM、XPS、PL、UV-vis进行了表征,进而以甲基橙为模拟污染物进行了光催化测试。结果表明,不同方法制备得到的ZnO/Ag纳米粉体晶粒均匀,无明显团聚现象,面心立方结构的金属Ag吸附在纤锌矿结构的ZnO表面形成异质结。与纯ZnO相比,掺Ag极大地改善了样品在紫外光下的光催化活性。对不同合成工艺的比较表明,用溶胶-凝胶一步法制备的ZnO/Ag复合物的光催化活性最高,经紫外光照射70min可完全降解甲基橙。     

Effect of Ag loading on activated carbon doped ZnO for bisphenol A degradation under visible light

Silver modified activated carbon doped zinc oxide (Ag/AC-ZnO) was synthesized via a calcination-electroless deposition route. The samples were characterized by X-ray powder diffractometry, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and UV–vis diffuse reflectance spectroscopy. The photocatalytic activity of the Ag/AC-ZnO was evaluated for bisphenol A degradation in the presence of H₂O₂ under visible light irradiation. The archived results showed that the photocatalytic activity of the Ag/AC-ZnO was higher than that of AC-ZnO and pure ZnO. The cytotoxicity of the bisphenol A after photocatalysis under visible light irradiation was tested using L929 mouse fibroblast cells and the obtained results indicated that the treated bisphenol A solution exhibited no cytotoxicity against normal cells.