Hydrodynamic Characteristics of a Pilot-Scale Screw Conveyor Dryer

This article presents results of an experimental study on the flow characteristics of a pilot-size screw conveyor dryer (SCD). In particular, the effects of granular solids flow rate (15.2–206 kg/h) and screw speed (10.8–28 rpm) on the residence time distribution (RTD) were studied using sand as the model material. The RTD was measured using a dynamic step change in the solids flow rate. Parameters such as solids holdup, degree of fullness, mean residence time, and uniformity of the discharge flow were studied. The solids holdup and hence the degree of fullness was found to decrease with increase in the screw speed and decrease with the solids flow rate. The mean residence time was found to decrease with an increase in the screw speed, as expected. The screw speed and the solids flow rate strongly affected the discharge uniformity. An optimum value of the degree of fullness was observed with regard to the solids flow rate. Over the operating range examined, the solids flow pattern was close to plug flow, as indicated by high values of N and Pe number.     

Hydrodynamic Characteristics of a Pilot-Scale Screw Conveyor Dryer

This article presents results of an experimental study on the flow characteristics of a pilot-size screw conveyor dryer (SCD). In particular, the effects of granular solids flow rate (15.2-206 kg/h) and screw speed (10.8-28 rpm) on the residence time distribution (RTD) were studied using sand as the model material. The RTD was measured using a dynamic step change in the solids flow rate. Parameters such as solids holdup, degree of fullness, mean residence time, and uniformity of the discharge flow were studied. The solids holdup and hence the degree of fullness was found to decrease with increase in the screw speed and decrease with the solids flow rate. The mean residence time was found to decrease with an increase in the screw speed, as expected. The screw speed and the solids flow rate strongly affected the discharge uniformity. An optimum value of the degree of fullness was observed with regard to the solids flow rate. Over the operating range examined, the solids flow pattern was close to plug flow, as indicated by high values of N and Pe number.     

Axial and lateral dispersion of fine particles in a binary-solid riser

Axial and lateral mixing of fine particles in a binary-solid riser have been investigated using a phosphor tracer method. The measured bimodal residence time distribution (RTD) demonstrated two types of axial dispersions of the fines: the dispersion of discrete particles and that of clusters. A proposed one-dimensional, bimodal dispersion model describes the bimodal RTDs very well. The axial Peclet number of the fines is not sensitive to the fraction of coarse particles, gas velocity and solids circulation rate. Lateral solids dispersion was determined by measuring the solids RTD at different radii using a point source tracer injection. A two-dimensional dispersion model describes the measured RTDs satisfactorily. Lateral solids mixing decreased as coarse particles were added into the riser. Correlations of the axial and lateral Peclet numbers obtained fit the experimental data well.     

流动方向对循环流化床中颗粒混合行为的影响

对循环流化床提升管及下行床两种不同气固流动方式对颗粒混合行为的影响进行了较为深入的对比分析，发现在影响循环流化床颗粒混合的众多因素（如操作条件、床层直径、颗粒性质及床层内构件等）中，气固流动方向是影响颗粒轴向混合的最主要因素．当气固流动为顺重力场时（下行床），颗粒的轴向混合很小，流型接近平推流；当气固流动为逆重力场的提升管时，轴向颗粒混合将成倍增大，颗粒流动远离平推流流动．分析表明，下行床中颗粒混合仅为单一的弥散颗粒扩散，而提升管中则存在着两种颗粒混合机制：弥散颗粒扩散及颗粒团扩散．弥散颗粒的扩散基本以平推流的形式通过循环流化床，提升管中大量的颗粒轴向返混归因于颗粒团的严重返混并由此形成了提升管中颗粒停留时间的双峰分布．     

A physical description of solids transport in flighted rotary dryers

In this paper, a solids transport model for flighted rotary dryers is presented. Emphasis is placed on combining statistical and mechanistic modelling efforts to create a physically motivated compartment model involving pairs of perfectly mixed tank reactors linked in a series arrangement. Here, each tank pair, or cell, aims to physically describe a finite slice of a case study industrial rotary sugar dryer, and is hence governed primarily by flight geometry and dryer operational variables such as rotational speed and dryer inclination. Solids flow paths are structured to properly represent the different modes of transport in the rotary dryer, and values of transport coefficients are based on calculated rates of rotational and axial flows. A solids dispersion variable is used to correlate the model residence time distribution (RTD) prediction with available data from a tracer study conducted during industrial operation of a full-scale raw sugar dryer. RTD results from the model show intuitive responses to variations in solids feed rate, rotational speed and drum inclination.     

CFD simulation of solids residence time distribution in a multi-compartment fluidized bed

The present work focuses on a numerical investigation of the solids residence time distribution(RTD)and the fluidized structure of a multi-compartment fluidized bed,in which the flow pattern is proved to be close to plug flow by using computational fluid dynamics(CFD)simulations.With the fluidizing gas velocity or the bed outlet height rising,the solids flow out of bed more quickly with a wider spread of residence time and a larger RTD variance(σ2).It is just the heterogeneous fluidized structure that being more prominent with the bed height increasing induces the widely non-uniform RTD.The division of the individual internal circulation into double ones improves the flow pattern to be close to plug flow.     

The Residence Time Distribution of the Liquid Phase in a Bubble Column and Its Effect on Ozone Transfer

Residence time distribution (RTD) experiments are carried out in a pilot plant (QL = 1 m³.h^?1). The RTD curves are analyzed by the completely mixed reactors in series model or by the axial dispersion model. Measurements are performed either on the overall bubble column or on four equal parts of the reactor. The bottom part (gas introduction) is completely mixed. The top part (water introduction) is a mixed reactor in which the middle parts are plug flow reactors with a weak axial dispersion coefficient. Dissolved ozone measurements along the column are in agreement with that model which allows a reactor modelization to compute the dissolved ozone profiles.     

鼓泡塔反应器分布板的开孔率和液体返混

考察鼓泡塔内鼓泡现象,发现气流经过小孔的速度（称为小孔气速）需大于某一临界值。计算并比较了气流通过多孔板的干板压力降和表面能损耗,提出计算此临界气速的公式和确定最大开孔率的方法。 用脉冲注入法测定鼓泡塔液体停留时间分布,提出非整数串连混合器模型,推导出其停留时间分布曲线方程式,计算结果与实验数据相符。并验证了Towell的轴向分散系数的计算方法。     

Analysis and interpretation of residence time distribution experimental curves in FM01-LC reactor using axial dispersion and plug dispersion exchange models with closed-closed boundary conditions

The liquid phase mixing flow pattern at low (20 < Re < 120) and intermediate liquid flow rate (120 < Re < 400) was studied by means of residence time distribution (RTD) experimental curve in an up-flow Filter Press electrochemical reactor (FM01-LC) bench scale. For this purpose, a plastic turbulence promoter was used with stainless-steel and platinised titanium structural meshes as electrodes in channel configuration. To visualize and determine the mixing flow pattern in the liquid phase, the stimulus-response technique was employed using dextran blue (D_M = 1.058 × 10⁻¹¹ m² s⁻¹, 25 °C, in water) as model tracer. A theoretical analysis and approximation RTD experimental curves with axial dispersion model (ADM) and plug dispersion exchange model (PDE), with “closed-closed vessel” boundary conditions were used in order to establish a better approximation of the axial dispersion, stagnant zones, channelling and by-pass (preference flow) effects present at low and intermediate Re. RTD curves show that the liquid flow pattern in the FM01-LC deviates considerably from axial dispersion model at low Re, where the FM01-LC exhibits large channelling, stagnant zones, and dead zone. The PDE model represents fairly this deviation from ideal flow (less dead zone).     

RTD studies in trickle bed reactors packed with porous particles

The residence time distribution (RTD) for liquid phase in a trickle bed reactor (TBR) has been experimentally studied for air-water system. Experiments were performed in a 15.2 cm diameter column using commerical alumina extrudates with D/d_p ratio equal to 75 to eliminate the radial flow differences. The range of liquid and gas flow rates covered was 3.76 < Re_L < 9.3 and 0 < Re_G < 2.92. The axial dispersion model was used to compute axial dispersion coefficient. The effect of liquid and gas flow rates on total liquid holdup and axial dispersion was investigated. The total liquid holdup has been correlated to liquid and gas flow rates.     

Liquid phase mixing in turbulent bed contactor

Axial mixing of the liquid phase in turbulent bed contactor (TBC) is studied through residence time distribution (RTD) experiments over a large range of variables such as flow rate of gas and liquid phases, static bed heights, diameter and density of particles and number of stages in presence of downcomer using air water system. Since all the liquid exits only through the downcomer, it enables the correct estimation of exit concentration of the tracer. The experimental RTD curves are satisfactorily compared with the axial dispersion model. The Peclet numbers evaluated by axial dispersion model and the Peclet numbers reported in the literature are used to propose a unified correlation in terms of operating and geometric parameters. Correlation is also developed for predicting the axial dispersion coefficient. It was observed in the present study that almost plug flow conditions can be achieved in multistage TBC.     

自热转化炉停留时间分布

以氢气作为示踪剂,运用脉冲法测定自热转化炉内停留时间的分布。实验结果表明:随着催化剂床层的增高,停留时间分布密度函数变窄,平均停留时间和量纲一方差均减小;当进口气量增大时,平均停留时间减小,量纲一方差增大。应用N个全混流反应器(CSTR)、轴向混合模型和平推流模型串联建立自热转化炉停留时间分布模型,由Laplace变换法和阻尼最小二乘法对模型参数进行估算,模型估计停留时间曲线与实验测量曲线吻合良好。     

Radioisotope tracer study in trickle bed reactors

The residence time distribution (RTD) of liquid phase in trickle bed reactors has been measured for air‐water system using radioisotope tracer technique. Experiments were carried out in a glass column of internal diameter of 0.152 m packed with glass beads and actual catalyst particles of two different shapes. From the measured RTD curves, mean residence time of liquid was calculated and used to estimate liquid holdup. The axial dispersion model was used to simulate the experimental data and estimate mixing index, ie. Peclet number. The effect of liquid and gas flow rates on total liquid holdup and Peclet number has been investigated. Results of the study indicated that shape of the packing has significant effect on holdup and axial dispersion. Bodenstein number has been correlated to Reynolds number, Galileo number, shape and size of the packing.     

Mixing characteristics in the torus reactor

The hydrodynamic characteristics of propeller-induced toroidal flow in a loop reactor were investigated by performing an RTD analysis. The experimental determination of circulation time allows the calculation of the mean axial velocity with respect to the rotational speed of the impeller. RTD measurements are interpreted with the aid of the dispersion plug flow model, and it is shown that axial dispersion is relatively weak in the torus reactor. The mixing time was also determined experimentally and related to the circulation time. A direct relationship between mixing time and axial dispersion coefficient has been established, leading to a correlation for the mixing time in a torus reactor.     

SOLIDS TRANSPORTATION MODEL OF AN INDUSTRIAL ROTARY DRYER

A complete simulation model has been developed for an industrial rotary dryer to account for the heat and mass exchange between the solids and the gas. This simulator is mainly composed of three models: solids transportation model, furnace model, and gas model. The solids transportation model is the modified Cholette-Cloutier model It consists of a series of interactive reservoirs which are subdivided into an active and a dead compartments to account for the characteristic extended tail of the residence time distribution (RTD) curves observed in industrial dryers.

To expand the validity of the model, experiments have been performed in an industrial rotary dryer to obtain RTD curves under different mineral concentrate and gas flow rates. This paper describes these experiments and presents the variation of the average residence time and model parameters as function of solids and gas flow rates.     

双颗粒提升管中细颗粒的混合行为研究(Ⅱ)──弥散颗粒的轴径向混合行为

利用磷光颗粒示踪技术,使用点源示踪的方法在不同的径向位置测得反映颗粒径向扩散行为的停留时间分布曲线,并对弥散细颗粒的径向混合行为进行了分析．提出二维扩散模型描述所测量的停留时间分布曲线特征．实验发现弥散细颗粒的径向扩散Peclet数随粗颗粒加入量的增加而增加,随细颗粒浓度的增大而增大,而几乎不随气速变化．给出了一个与实验数据吻合较好并可适用于单颗粒提升管的关联式．     

Particle residence time distributions in circulating fluidised beds

This paper gives experimental measurements of the particle residence time distribution (RTD) made in the riser of a square cross section, cold model, circulating fluidised bed, using the fast response particle RTD technique developed by Harris et al. (Chem. Eng. J. 89 (2002a) 127). This technique depends upon all particles having phosphorescent properties. A small proportion of the particles become tracers when activated by a flash of light at the riser entry; the concentration of these phosphorescent particles can subsequently be detected by a photomultiplier. The influence of the solids circulation rate and superficial gas velocity on the RTD were investigated. The results presented are novel because (i) the experiments were performed in a system with closed boundaries and hence give the true residence time distribution in the riser and (ii) the measurement of the tracer concentration is exceedingly fast. The majority of previous studies have measured the RTD in risers with open boundaries, giving an erroneous measure of the RTD.Analysis of the results suggests that using pressure measurements in a riser to infer the solids inventory leads to erroneous estimates of the mean residence time. In particular, the results cast doubt on the assumption that friction and acceleration effects can be neglected when inferring the axial solids concentration profile from riser pressure measurements.An assessment of particle RTD models is also given. A stochastic particle RTD model was coupled to a riser hydrodynamic model incorporating the four main hydrodynamic regions observed in a fast-fluidised bed riser namely (i) the entrance region, (ii) a transition region, (iii) a core-annulus region and (iv) an exit region. This model successfully predicts the experimental residence time distributions.     

双颗粒提升管中细颗粒的混合行为研究(Ⅱ)──弥散颗粒的轴径向混合行为

利用磷光颗粒示踪技术，使用点源示踪的方法在不同的径向位置测得反映颗粒径向扩散行为的停留时间分布曲线，并对弥散细颗粒的径向混合行为进行了分析．提出二维扩散模型描述所测量的停留时间分布曲线特征．实验发现弥散细颗粒的径向扩散Peclet数随粗颗粒加入量的增加而增加，随细颗粒浓度的增大而增大，而几乎不随气速变化．给出了一个与实验数据吻合较好并可适用于单颗粒提升管的关联式．     

SOLIDS TRANSPORTATION MODEL OF AN INDUSTRIAL ROTARY DRYER

ABSTRACT

A complete simulation model has been developed for an industrial rotary dryer to account for the heat and mass exchange between the solids and the gas. This simulator is mainly composed of three models: solids transportation model, furnace model, and gas model. The solids transportation model is the modified Cholette-Cloutier model It consists of a series of interactive reservoirs which are subdivided into an active and a dead compartments to account for the characteristic extended tail of the residence time distribution (RTD) curves observed in industrial dryers.

To expand the validity of the model, experiments have been performed in an industrial rotary dryer to obtain RTD curves under different mineral concentrate and gas flow rates. This paper describes these experiments and presents the variation of the average residence time and model parameters as function of solids and gas flow rates.     

振荡流反应器的物料停留时间分布模型研究

提出了一个基于马尔柯夫链（Markov chains）的考虑腔室间返混的振荡流反应器物料停留时间分布模型。通过对在内径50mm,长1．95m的振荡流反应器进行的理想脉冲示踪试验数据的统计分析,给出了模型的唯一参数回流比R的经验计算公式。发现在试验条件下,存在一个与最小回流比R相对应的振荡条件。这振荡条件可表示为振荡流雷诺数（Reo）与净流雷诺数（Ren）的比值ζ,其范围为1．6〈ζ〈2．5。