A 1 V Wireless Transceiver for an Ultra-Low-Power SoC for Biotelemetry Applications

This paper presents a 1 V RF transceiver for biotelemetry and wireless body sensor network (WBSN) applications, realized as part of an ultra low power system-on-chip (SoC), the Sensiumtrade. The transceiver utilizes FSK/GFSK modulation at a data rate of 50 kbit/s to provide wireless connectivity between target sensor nodes and a central base-station node in a single-hop star network topology operating in the 862-870 MHz European short-range-device (SRD) and the 902-928 MHz North American Industrial, Scientific & Medical (ISM) frequency bands. Controlled by a proprietary media access controller (MAC) which is hardware implemented on chip, the transceiver operates half-duplex, achieving -102 dBm receiver input sensitivity (for 1E-3 raw bit error rate) and up to -7 dBm transmitter output power through a single antenna port. It consumes 2.1 mA during receive and up to 2.6 mA during transmit from a 0.9 to 1.5 V supply. It is fabricated in a 0.13 mum CMOS technology and occupies 7 mm² in a SoC die size of 4 times 4 mm².     

A dual-mode 802.11b/bluetooth radio in 0.35-/spl mu/m CMOS

A fully integrated dual-mode CMOS transceiver tuned to 2.4 GHz consumes 65 mA in receive mode and 78 mA in transmit mode from a 3-V supply. The radio includes all the receive and transmit building blocks, such as frequency synthesizer, voltage-controlled oscillator (VCO), and power amplifier, and is intended for use in 802.11b and Bluetooth applications. The Bluetooth receiver uses a low-IF architecture for higher level of integration and lower power consumption, while the 802.11b receiver is direct conversion. The receiver achieves a typical sensitivity of -88 dBm at 11 Mb/s for 802.11b, and -83 dBm for Bluetooth mode. The receiver minimum IIP3 is -8 dBm. Both transmitters use a direct-conversion architecture, and deliver a nominal output power of 0 dBm, with a power range of 20 dB in 2-dB steps.     

A 2.4-GHz CMOS transceiver for Bluetooth

A fully integrated CMOS transceiver tuned to 2.4 GHz consumes 46 mA in receive mode and 47 mA in transmit mode from a 2.7-V supply. It includes all the receive and transmit building blocks, such as frequency synthesizer, voltage-controlled oscillator (VCO), power amplifier, and demodulator. The receiver uses a low-IF architecture for higher level of integration and lower power consumption. It achieves a sensitivity of -82 dBm at 0.1% BER, and a third-order input intercept point (IIP3) of -7 dBm. The direct-conversion transmitter delivers a GFSK modulated spectrum at a nominal output power of 4 dBm. The on-chip voltage controlled oscillator has a close-in phase-noise of -120 dBc/Hz at 3-MHz offset     

A low-power CMOS Bluetooth RF transceiver with a digital offset canceling DLL-based GFSK demodulator

This paper presents a fully integrated 0.18-/spl mu/m CMOS Bluetooth transceiver. The chip consumes 33 mA in receive mode and 25 mA in transmit mode from a 3-V system supply. The receiver uses a low-IF (3-MHz) architecture, and the transmitter uses a direct modulation with ROM-based Gaussian low-pass filter and I/Q direct digital frequency synthesizer for high level of integration and low power consumption. A new frequency shift keying demodulator based on a delay-locked loop with a digital frequency offset canceller is proposed. The demodulator operates without harmonic distortion, handles up to /spl plusmn/160-kHz frequency offset, and consumes only 2 mA from a 1.8-V supply. The receiver dynamic range is from -78 dBm to -16 dBm at 0.1% bit-error rate, and the transmitter delivers a maximum of 0 dBm with 20-dB digital power control capability.     

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver is presented. The problems to implement the low voltage design and the on-chip input/output impedance matching are considered, and some improved circuits are presented to overcome the problems. Especially, a single-end input, differential output double balanced mixer with an on-chip bias loop is analyzed in detail to show its advantages over other mixers. The transceiver RF front-end has been implemented in 0.18 um CMOS process, the measured results show that the Rx front-end achieves 5.23 dB noise figure, 12.7 dB power gain (50 ohm load), −18 dBm input 1 dB compression point (ICP) and −7 dBm IIP3, and the Tx front-end could output +2.1 dBm power into 50 ohm load with 23.8 dB power gain. The transceiver RF front-end draws 13.6 mA current from a supply voltage of 1.8 V in receive mode and 27.6 mA current in transmit mode. The transceiver RF front-end could satisfy the performance requirements of IEEE802.11b WLAN standard. Supported by the National Natural Science Foundation of China, No. 90407006 and No. 60475018.     

5-GHz SiGe HBT monolithic radio transceiver with tunable filtering

A wide-band CDMA-compliant fully integrated 5-GHz radio transceiver was realized in SiGe heterojunction-bipolar-transistor technology with on-chip tunable voltage controlled oscillator (VCO) tracking filters. It allows for wide-band modulation schemes with bandwidth up to 20 MHz. The receiver has a single-ended single-sideband noise figure of 5.9 dB, more than 40 dB on-chip image rejection, an input compression point of -22 dBm, and larger than 70 dB local-oscillator-RF isolation. The phase noise of the on-chip VCO is -100 and -128 dBc/Hz at 100 kHz and 5 MHz offset from the carrier, respectively. The transmitter output compression point is +10 dBm. An image rejection better than 40 dB throughout the VCO tracking range has been demonstrated in the transmitter with all spurious signals 40 dB below the carrier. The differential transceiver draws 125 mA in transmit mode and 45 mA in receive mode from a 3.5-V supply     

A Fully Integrated 2.4-GHz IEEE 802.15.4-Compliant Transceiver for ZigBee™ Applications

A single-chip 2.4-GHz CMOS radio transceiver with integrated baseband processing according to the IEEE 802.15.4 standard is presented. The transceiver consumes 14.7 mA in receive mode and 15.7 mA in transmit mode. The receiver uses a low-IF topology for high sensitivity and low power consumption, and achieves -101 dBm sensitivity for 1% packet error rate. The transmitter topology is based on a PLL direct-modulation scheme. Optimizations of architecture and circuit design level in order to reduce the transceiver power consumption are described. Special attention is paid to the RF front-end design which consumes 2.4mA in receive mode and features bidirectional RF pins. The 5.77 mm² chip is implemented in a standard 0.18-mum CMOS technology. The transmitter delivers +3 dBm into the 100-Omega differential antenna port     

Low‐Power Direct Conversion Transceiver for 915 MHz Band IEEE 802.15.4b Standard Based on 0.18 μm CMOS Technology

This paper presents the experimental results of a low‐power low‐cost RF transceiver for the 915 MHz band IEEE 802.15.4b standard. Low power and low cost are achieved by optimizing the transceiver architecture and circuit design techniques. The proposed transceiver shares the analog baseband section for both receive and transmit modes to reduce the silicon area. The RF transceiver consumes 11.2 mA in receive mode and 22.5 mA in transmit mode under a supply voltage of 1.8 V, in which 5 mA of quadrature voltage controlled oscillator is included. The proposed transceiver is implemented in a 0.18 μm CMOS process and occupies 10 mm² of silicon area.     

A 2.5-GHz BiCMOS transceiver for wireless LAN's

A BiCMOS transceiver intended for spread spectrum applications in the 2.4-2.5 GHz band is described. The IC contains a low-noise amplifier (LNA) with 14 dB gain and 2.2 dB NF in its high-gain mode, a downconversion mixer with 8 dB gain and 11 dB NF, and an upconversion mixer with 17 dB gain and P_{-1 dB} of +3 dBm out. An on-chip local oscillator (LO) buffer accepts LO drive of -10 dBm with a half-frequency option allowed by an on-chip frequency doubler. Power consumption from a single 3-V supply is 34 mA in transmit mode, 21 mA in receive mode, and 1 μA in sleep mode     

A 1.9-GHz Single-Chip CMOS PHS Cellphone

A single-chip CMOS PHS cellphone, integrated in a 0.18-mum CMOS technology, implements all handset functions including radio, voice, audio, MODEM, TDMA controller, CPU, and digital interfaces. Both the receiver and transmitter are based on a direct conversion architecture. The RF transceiver achieves -106 dBm receive sensitivity and +4 dBm EVM-compliant transmit power. The local oscillator, based on a sigma-delta fractional-N synthesizer, has a phase noise of -118 dBc/Hz at 600kHz offset and settling time of 15 mus. The current consumption for the receiver, transmitter and synthesizer are 32 mA, 29 mA, and 25 mA, respectively, from a 3.0 V supply     

A multimode 0.3-200-kb/s transceiver for the 433/868/915-MHz bands in 0.25-/spl mu/m CMOS

A fully integrated transceiver suitable for low-data-rate wireless telemetry and sensor networks operating in the license-free ISM frequency bands at 433, 868, or 915 MHz implemented in 0.25-/spl mu/m CMOS is presented. G/FSK, ASK, and OOK modulation formats are supported at data rates from 0.3 to 200 kb/s. The transceiver's analog building blocks include a low-noise amplifier, mixer, channel filter, received signal-strength indication, frequency synthesizer, voltage-controlled oscillator, and power amplifier. FSK demodulation is implemented using a novel digital complex-frequency correlator that operates over a wide modulation-index range and approximates matched filter detection performance. Automatic gain control, automatic frequency control, and symbol timing recovery loops are included on chip. Operating in the 915-MHz band in FSK mode at 9.6 kb/s, the receiver consumes 19.7 mA from a 3-V supply and achieves a sensitivity of -112.8dBm at 0.1% BER. The transmitter consumes 28.5 mA for an output power of 10 dBm and delivers up to 14 dBm.     

A Dual‐Mode 2.4‐GHz CMOS Transceiver for High‐Rate Bluetooth Systems

This paper reports on our development of a dual‐mode transceiver for a CMOS high‐rate Bluetooth system‐on‐chip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front‐end. It is designed for both the normal‐rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high‐rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual‐path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual‐mode system. The transceiver requires none of the external image‐rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order on‐chip filters. The chip is fabricated on a 6.5‐mm² die using a standard 0.25‐μm CMOS technology. Experimental results show an in‐band image‐rejection ratio of 40 dB, an IIP3 of ?5 dBm, and a sensitivity of ?77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive π/4‐diffrential quadrature phase‐shift keying (π/4‐DQPSK) mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5‐V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low‐cost, multi‐mode, high‐speed wireless personal area network.     

A Bluetooth radio in 0.18-/spl mu/m CMOS

This paper describes the results of an implementation of a Bluetooth radio in a 0.18-/spl mu/m CMOS process. A low-IF image-reject conversion architecture is used for the receiver. The transmitter uses direct IQ-upconversion. The VCO runs at 4.8-5.0 GHz, thus facilitating the generation of 0/spl deg/ and 90/spl deg/ signals for both the receiver and transmitter. By using an inductor-less LNA and the extensive use of mismatch simulations, the smallest silicon area for a Bluetooth radio implementation so far can be reached: 5.5 mm/sup 2/. The transceiver consumes 30 mA in receive mode and 35 mA in transmit mode from a 2.5 to 3.0-V power supply. As the radio operates on the same die as baseband and SW, the crosstalk-on-silicon is an important issue. This crosstalk problem was taken into consideration from the start of the project. Sensitivity was measured at -82 dBm.     

A Low-Power Dual-Band Triple-Mode WLAN CMOS Transceiver

This paper describes a 0.18-mum CMOS direct-conversion dual-band triple-mode wireless LAN transceiver. The transceiver has a concurrent dual-band low-noise amplifier for low power consumption with a low noise figure, a single widely tunable low-pass filter based on a triode-biased MOSFET transconductor for multi-mode operation with low power consumption, a DC-offset compensation circuit with an adaptive activating feedback loop to achieve a fast response time with low power consumption, and a SigmaDelta-based low-phase-noise fractional-N frequency synthesizer with a switched-resonator voltage controlled oscillator to cover the entire frequency range for the IEEE WLAN standards. The transceiver covers both 2.4-2.5 and 4.9-5.95 GHz and has extremely low power consumption (78 mA in receive mode, 76 mA in transmit mode-both at 2.4/5.2 GHz). A system noise figure of 3.5/4.2 dB, a sensitivity of -93/-94 dBm for a 6-Mb/s OFDM signal, and an error vector magnitude of 3.2/3.4% were obtained at 2.4/5.2 GHz, respectively     

A 900 MHz Zero‐IF RF Transceiver for IEEE 802.15.4g SUN OFDM Systems

This paper presents a 900 MHz zero‐IF RF transceiver for IEEE 802.15.4g Smart Utility Networks OFDM systems. The proposed RF transceiver comprises an RF front end, a Tx baseband analog circuit, an Rx baseband analog circuit, and a ΔΣ fractional‐N frequency synthesizer. In the RF front end, re‐use of a matching network reduces the chip size of the RF transceiver. Since a T/Rx switch is implemented only at the input of the low‐noise amplifier, the driver amplifier can deliver its output power to an antenna without any signal loss; thus, leading to a low dc power consumption. The proposed current‐driven passive mixer in Rx and voltage‐mode passive mixer in Tx can mitigate the IQ crosstalk problem, while maintaining 50% duty‐cycle in local oscillator clocks. The overall Rx‐baseband circuits can provide a voltage gain of 70 dB with a 1 dB gain control step. The proposed RF transceiver is implemented in a 0.18 μm CMOS technology and consumes 37 mA in Tx mode and 38 mA in Rx mode from a 1.8 V supply voltage. The fabricated chip shows a Tx average power of ?2 dBm, a sensitivity level of ?103 dBm at 100 Kbps with , an Rx input P_1dB of ?11 dBm, and an Rx input IP3 of ?2.3 dBm.     

应用于IEEE 802.11b无线局域网系统的2.4GHzCMOS单片收发机射频前端

实现了一个应用于IEEE 802.11b无线局域网系统的2.4GHz CMOS单片收发机射频前端,它的接收机和发射机都采用了性能优良的超外差结构.该射频前端由五个模块组成:低噪声放大器、下变频器、上变频器、末前级和LO缓冲器.除了下变频器的输出采用了开漏级输出外,各模块的输入、输出端都在片匹配到50Ω.该射频前端已经采用0.18μm CMOS工艺实现.当低噪声放大器和下变频器直接级联时,测量到的噪声系数约为5.2dB,功率增益为12.5dB,输入1dB压缩点约为-18dBm,输入三阶交调点约为-7dBm.当上变频器和末前级直接级联时,测量到的噪声系数约为12.4dB,功率增益约为23.8dB,输出1dB压缩点约为1.5dBm,输出三阶交调点约为16dBm.接收机射频前端和发射机射频前端都采用1.8V电源,消耗的电流分别为13.6和27.6mA.     

A 77-GHz Phased-Array Transceiver With On-Chip Antennas in Silicon: Transmitter and Local LO-Path Phase Shifting

Integration of mm-wave multiple-antenna systems on silicon-based processes enables complex, low-cost systems for high-frequency communication and sensing applications. In this paper, the transmitter and LO-path phase-shifting sections of the first fully integrated 77-GHz phased-array transceiver are presented. The SiGe transceiver utilizes a local LO-path phase-shifting architecture to achieve beam steering and includes four transmit and receive elements, along with the LO frequency generation and distribution circuitry. The local LO-path phase-shifting scheme enables a robust distribution network that scales well with increasing frequency and/or number of elements while providing high-resolution phase shifts. Each element of the heterodyne transmitter generates +12.5 dBm of output power at 77 GHz with a bandwidth of 2.5 GHz leading to a 4-element effective isotropic radiated power (EIRP) of 24.5 dBm. Each on-chip PA has a maximum saturated power of +17.5 dBm at 77 GHz. The phased-array performance is measured using an internal test option and achieves 12-dB peak-to-null ratio with two transmit and receive elements active     

Determination of receiver selectivity and transmit frequency usinga common resonator

In this work, the determination of receiver selectivity and transmit frequency using a common resonator is presented for a 5.3 GHz transceiver employing a time division duplex, on-off keyed modulation format. The microstrip circuit is fabricated on Rogers RO4003^(R) , a high frequency laminate. In receive mode, a 3 dB passband of 35 MHz and a small-signal gain of 26 dB has been achieved. In transmit mode, an output power of +7 dBm for the fundamental, -15.0 dBm for the second harmonic, -18.0 dBm for the third harmonic, and -35.0 dBm for the fourth harmonic has been achieved     

A Low-Power Fullband 802.11a/b/g WLAN Transceiver With On-Chip PA

A low-power fullband 802.11a/b/g WLAN transceiver in 0.15-mum CMOS technology is described. The zero-IF transceiver achieves a receiver noise figure of 4.4/4 dB for the 2.4-GHz/5-GHz bands, respectively. The corresponding sensitivity at 54-Mb/s operation is -72 dBm for 802.11g and -74 dBm for 802.11a using actual PER measurement. An on-chip PA delivers 20 dBm output P1-dB. A new I/Q compensation scheme is implemented in local oscillator (LO) and an image rejection of better than 52 dB is observed. The transmitter delivers 10/1.5 dBm (2.4-/5-GHz) EVM-compliant output power for a 64-QAM OFDM signal at 54-Mb/s. The power consumption is 117/135 mW (1.8-V) in the receive mode and 570/233.1 mW in the transmit mode for 2.4/5 GHz, respectively. The low power consumption, high integration and robustness (-40 to 140degC) make this transceiver suitable for portable applications     

A 5-GHz direct-conversion CMOS transceiver utilizing automatic frequency control for the IEEE 802.11a wireless LAN standard

A fully integrated CMOS direct-conversion 5-GHz transceiver with automatic frequency control is implemented in a 0.18-/spl mu/m digital CMOS process and housed in an LPCC-48 package. This chip, along with a companion baseband chip, provides a complete 802.11a solution The transceiver consumes 150 mW in receive mode and 380 mW in transmit mode while transmitting +15-dBm output power. The receiver achieves a sensitivity of better than -93.7dBm and -73.9dBm for 6 Mb/s and 54 Mb/s, respectively (even using hard-decision decoding). The transceiver achieves a 4-dB receive noise figure and a +23-dBm transmitter saturated output power. The transmitter also achieves a transmit error vector magnitude of -33 dB. The IC occupies a total die area of 11.7 mm/sup 2/ and is packaged in a 48-pin LPCC package. The chip passes better than /spl plusmn/2.5-kV ESD performance. Various integrated self-contained or system-level calibration capabilities allow for high performance and high yield.