Phase-structural and morphological features,dehydrogenation/re-hydrogenation performance and hydrolysis of nanocomposites prepared by ball milling of MgH2 with germanium

Ball milling of magnesium hydride with germanium additives in argon for up to 10 h was shown to result in the formation of nanocomposites of α- and γ-modifications of MgH₂ together with individual Ge phase. When the as milled samples are heated-up, Ge interacts with MgH₂ to form Mg₂Ge at T = 350–400 °C; the phase transformation overlaps with MgH₂ decomposition and Mg₂Ge phase remains in the material after its re-hydrogenation at T = 300 °C and P(H₂)∼15 bar.The ball milled Ge-MgH₂ nanocomposites were found to be characterised by an improved hydrogen release via hydrolysis in organic acid solutions as compared to pure MgH₂ prepared and tested at the same conditions. It was found that the composite containing 5 wt% of Ge and ball milled for 5 h showed the best hydrogen generation performance, with total hydrogen release exceeding 1.55 NL/g (yield close to 100%) in one minute.     

Mg2FeH6–LiBH4 and Mg2FeH6–LiNH2 composite materials for hydrogen storage

Two composite hydrogen storage materials based on Mg₂FeH₆ were investigated for the first time. The Mg₂FeH₆–LiBH₄ composite of molar ratio 1:5 showed a hydrogen desorption capacity of 5.6 wt.% at 370 °C, and could be rehydrogenated to 3.6 wt.% with the formation of MgH₂, as the material was heated to 445 °C and held at this temperature. The Mg₂FeH₆–LiNH₂ composite of 3:10 molar ratio exhibited a hydrogen desorption capacity of 4.3 wt.% and released hydrogen at 100 °C lower then the Mg₂FeH₆–LiBH₄ composite, but this mixture could not be rehydrogenated. Compared to neat Mg₂FeH₆, both composites show enhanced hydrogen storage properties in terms of desorption kinetics and capacity at these low temperatures. In particular, Mg₂FeH₆–LiNH₂ exhibits a much lower desorption temperature than neat Mg₂FeH₆, but only Mg₂FeH₆–LiBH₄ re-absorbs hydrogen.     

Formation and hydrogen storage behavior of nanostructured Mg2FeH6 in a compressed 2MgH2–Fe composite

The present study focuses on enhancing the yield of Mg₂FeH₆ and its hydrogen storage performances through a novel high-pressure compression approach. For which, MgH₂ and Fe powders are first mechanically milled in a molar ratio of 2:1 and subsequently compressed to a cylindrical pellet. Due to the compression, the yield of Mg₂FeH₆ in the compressed 2MgH₂–Fe pellet (90%) has been increased by 24% as compared to the reference ball-milled powder (66%). The thermodynamic destabilization of Mg₂FeH₆ in the pelletized sample is observed through measuring the pressure-composition isotherms, resulting in the reduced ab/desorption enthalpy for the pellet sample (−68.34 and 75.61 kJ/mol H₂, respectively). The hydrogen uptake and release kinetics of Mg₂FeH₆ is remarkably fast, and it can store/release about 5 wt% H in less than 2.5 min at 400 °C. The faster hydrogen ab/desorption kinetics corresponds to the lower activation energies (36 and 95 kJ/mol H₂, respectively). The excellent yield of Mg₂FeH₆ and its improved hydrogen storage properties for the compressed pellet are primarily attributed to the microstructural modifications upon high-pressure compression, and also the obtained results for Mg₂FeH₆ ternary hydride are linked to the literature data based on theoretical calculations.     

The influence of the milling time on the yield of Mg2FeH6 from a two-step synthesis conducted in a custom-made reactor

Dimagnesium iron hydride was synthesized by mechanical milling of a MgH₂/Fe mixture followed by sintering under a high hydrogen pressure (120 bar). The influence of the milling time on the synthesis yield was observed. Properly chosen processing parameters led to a 94–97 % reaction yield (depending on the measurement method) for the formation of Mg₂FeH₆. Milling times that were too short or too long proved to be ineffective. A custom-made reactor for synthesis of a batch of up to 20 g is presented. Synthesized samples were characterized by XRD analysis and PCT measurements were performed.     

Enhancing hydrogen storage performance of MgH2 through the addition of BaMnO3 synthesized via solid-state method

Currently, magnesium hydride (MgH₂) as a solid-state hydrogen storage material has become the subject of major research owing to its good reversibility, large hydrogen storage capacity (7.6 wt%) and affordability. However, MgH₂ has a high decomposition temperature (>400 °C) and slow desorption and absorption kinetics. In this work, BaMnO₃ was synthesized using the solid-state method and was used as an additive to overcome the drawbacks of MgH₂. Interestingly, after adding 10 wt% of BaMnO₃, the initial desorption temperature of MgH₂ decreased to 282 °C, which was 138 °C lower than that of pure MgH₂ and 61 °C lower than that of milled MgH₂. For absorption kinetics, at 250 °C in 2 min, 10 wt% of BaMnO₃-doped MgH₂ absorbed 5.22 wt% of H₂ compared to milled MgH₂ (3.48 wt%). Conversely, the desorption kinetics also demonstrated that 10 wt% of BaMnO₃-doped MgH₂ samples desorbed 5.36 wt% of H₂ at 300 °C within 1 h whereas milled MgH₂ only released less than 0.32 wt% of H₂. The activation energy was lowered by 45 kJ/mol compared to that of MgH₂ after the addition of 10 wt% of BaMnO₃. Further analyzed by using XRD revealed that the formation of Mg_0·9Mn_0·1O, Mn₃O₄ and Ba or Ba-containing enhanced the performance of MgH₂.     

Room temperature conversion of Mg to MgH2 assisted by low fractions of additives

In recent works, it was noticed that Mg/MgH₂ mixed with additives by high energy ball milling allows temperature reductions of H₂ absorption/desorption without necessarily changing thermodynamic properties. Thus, the objective of this work was to investigate which additives, mixed in low fractions with MgH₂ powder would act as efficient hydrogen absorption/desorption catalysts at low temperatures, mainly at room temperature (RT). MgH₂ mixtures with 2 mol% additives (Fe, Nb₂O₅, TiAl and TiFe) were prepared by high energy reactive ball milling (RM). MgH₂–TiFe mixture showed the best results, both during desorption at 330 °C and absorption at RT. The hydrogen absorption was ≈ 2.67 wt% H₂ in 1 h and ≈ 4.44 wt% H₂ in 16 h (40% and 67% of maximum theoretical capacity, respectively). The MgH₂–TiFe superior performance was attributed to the hydrogen attraction by the created high energy interfaces and strong TiFe catalytic action facilitating the H₂ flow during Mg/MgH₂ reactions.     

Sorption behavior of the MgH2–Mg2FeH6 hydride storage system synthesized by mechanical milling followed by sintering

The hydrogen sorption behavior of the Mg₂FeH₆–MgH₂ hydride system is investigated via in-situ synchrotron and laboratory powder X-ray diffraction (SR-PXD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), particle size distribution (PSD) and volumetric techniques. The Mg₂FeH₆–MgH₂ hydride system is obtained by mechanical milling in argon atmosphere followed by sintering at high temperature and hydrogen pressure. In-situ SR-PXD results show that upon hydriding MgH₂ is a precursor for Mg₂FeH₆ formation and remained as hydrided phase in the obtained material. Diffusion constraints preclude the further formation of Mg₂FeH₆. Upon dehydriding, our results suggest that MgH₂ and Mg₂FeH₆ decompose independently in a narrow temperature range between 275 and 300 °C. Moreover, the decomposition behavior of both hydrides in the Mg₂FeH₆–MgH₂ hydride mixture is influenced by each other via dual synergetic-destabilizing effects. The final hydriding/dehydriding products and therefore the kinetic behavior of the Mg₂FeH₆–MgH₂ hydride system exhibits a strong dependence on the temperature and pressure conditions.     

Synthesis and decomposition mechanisms of Mg2FeH6 studied by in-situ synchrotron X-ray diffraction and high-pressure DSC

Synthesis and decomposition mechanisms of ternary Mg₂FeH₆ were investigated using in-situ synchrotron radiation powder X-ray diffraction (SR-PXD) and high-pressure differential scanning calorimetry (HP-DSC). Two routes for synthesis of Mg₂FeH₆ were studied. The first utilizes a ball-milled homogeneous MgH₂–Fe powder mixture and the second uses a mixture of Fe and Mg formed by decomposition of the ternary hydride, Mg₂FeH₆. In both cases the reaction mixture was sintered in a temperature range from RT to 500 °C under a hydrogen pressure of 100–120 bar. The reaction mechanisms were established using in-situ SR-PXD. The formation of Mg₂FeH₆ consists of two steps with MgH₂ as an intermediate compound, and the presence of magnesium was not observed. In contrast, the decomposition of Mg₂FeH₆ was found to be a single-step reaction. Additionally, both reactions were investigated using HP-DSC under similar conditions as in the SR-PXD experiments in order to estimate reaction enthalpies and temperatures. Mg₂FeH₆ was found to form from MgH₂ and Fe under hydrogen pressure regardless of whether the MgH₂ was introduced in the mixture or formed prior to creation of the ternary hydride.     

The effect of ball-milling gas environment on the sorption kinetics of MgH2 with/without additives for hydrogen storage

A study of the effect of the ball-milling gas environment on the kinetic enhancement of MgH₂ with different additives was conducted using argon and hydrogen. The as-sourced MgH₂ was milled for 20 h and then milled for a further 2 h after adding 1–2 mol% of one of the additives titanium isopropoxide, niobium oxide or carbon buckyballs, varying the gas environment for both ball-milling stages. The milling environment had little or no effect on the desorption kinetics in most cases. However, in some cases, the absorption uptake differed by up to 2 wt%, depending on the gas used_. This effect was not consistent among the composite samples surveyed, demonstrating the importance of reporting all information about the ball-milling processes used, including the gas environment.     

Nanocrystalline β-γ-β cyclic phase transformation in reacted ball milled MgH2 powders

Pure magnesium powders were ball milled under a hydrogen pressure of 50 bar at room temperature, using reactive ball milling (RBM) approach. The results have shown that a single stable phase of β-MgH₂ is obtained upon RBM for 25 h. Increasing the RBM time leads to a significant decreasing on the grain size and an increase in the iron contamination that were introduced to the powders upon using hard steel milling tools. Remarkable changes in the transformed mass fractions of β-MgH₂ phase to a metastable γ-MgH₂ phase with increasing the RBM time could be detected. Cyclic β-γ-β phase transformations were observed several times upon changing the RBM time. After 200 h of RBM time, the decomposition temperature and activation energy were recorded to be 399 °C and 131 kJ/mol, respectively. Moreover, the times required for complete absorption and desorption of 7 wt.% of hydrogen at 250 °C were recorded to be 3140 s and 35,207 s under 10 and 0 bar, respectively. At 300 °C, the powders that were obtained upon RBM time for 200 h possess excellent hydrogenation properties for any pure MgH₂ system, indexed by high hydrogen storage capacity (7.54 wt.%) with complete 600 absorption/desorption cycles. Improvements of hydrogenation/dehydrogenation kinetics are attributed to the presence of γ-phase, the existence of Fe contamination and the nanocrystallinity of the ball milled powders.     

Studies on de/rehydrogenation characteristics of nanocrystalline MgH2 co-catalyzed with Ti,Fe and Ni

In the present study, we have investigated the combined effect of different transition metals such as Ti, Fe and Ni on the de/rehydrogenation characteristics of nano MgH₂. Mechanical milling of MgH₂ with 5 wt% each of Ti, Fe and Ni for 24 h at 12 atm of H₂ pressure lead to the formation of nano MgH₂-Ti5Fe5Ni5. The decomposition temperature of nano MgH₂-Ti5Fe5Ni5 is lowered by 90 °C as compared to nano MgH₂ alone. It is also found that the nano MgH₂-Ti5Fe5Ni5 absorbs 5.3 wt% within 15 min at 270 °C and 12 atm hydrogen pressures. However, nano MgH₂ reabsorbs only 4.2 wt% under identical condition. An interesting result of the present study is that mechanical milling of MgH₂ separately with Fe and Ni besides refinement in particle size also leads to the formation of alloys Mg₂NiH₄ and Mg₂FeH₆ respectively. On the other hand, when MgH₂ is mechanically milled together with Ti, Fe and Ni, the dominant result is the formation of nano particles of MgH₂. Moreover the activation energy for dehydrogenation of nano MgH₂ co-catalyzed with Ti, Fe and Ni is 45.67 kJ/mol which is 35.71 kJ/mol lower as compared to activation energy of nano MgH₂ (81.34 kJ/mol). These results are one of the most significant in regard to improvement in de/rehydrogenation characteristics of known MgH₂ catalyzed through transition metal elements.     

Effect of V,Nb, Ti and graphite additions on the hydrogen desorption temperature of magnesium hydride

In this study the effects of mechanical milling with 5 wt.% of additives (V, Nb, Ti and Graphite) on the hydrogen desorption temperature of the magnesium hydride (MgH₂) were studied. The powder mixtures were mechanically milled for 2 h. X-ray diffraction (XRD), scanning electron microscope (SEM), and optical microscope (OM) techniques were used for the structural and morphological characterization of powders. Differential scanning calorimeter (DSC) was used to investigate the effects of the mechanical milling with additives on the hydrogen desorption temperature of the magnesium hydride powder. DSC results show that the hydrogen desorption temperatures of mechanically milled MgH₂ with additives are depressed about ∼40–50 °C compared with that of as-received MgH₂. The particle size analysis results indicate that decrease of the particle size of powders leads to a decrease of the hydrogen desorption temperature. Moreover, increasing specific surface area can also contribute to a decrease on the hydrogen desorption temperature.     

Dynamic synthesis of ternary Mg2FeH6

This work presents new results on the dynamic synthesis and decomposition of ternary Mg₂FeH₆. A novel synthesis method was applied for the rapid and effective synthesis of a ternary Mg–Fe hydride. This method consists of two processing routes. The first route involves high-energy ball milling of the initial MgH₂–Fe powder mixture, while the second is composed of a unique pressurizing and heating cycle route to obtain a full phase transformation within half an hour. The structural investigations carried out by X-ray diffraction revealed that almost all of the initial powder mixture transforms into the ternary hydride. Furthermore, the sample, which was synthesized, was also decomposed and reloaded with hydrogen. The formation of Mg₂FeH₆ consists of two steps that involve MgH₂ as an intermediate compound. In contrast, the decomposition of Mg₂FeH₆ consists of only one step and does not follow the inverse route. Some traces of iron were found in the reaction products. TDP results show that a desorption peak occurs at 315 °C, and this is in good agreement with DSC measurements showing only a single endothermic peak around 340 °C. Microstructural examinations revealed that the synthesized Mg₂FeH₆ powder generally exhibits a duplex structure that consists of plate-like particles larger than 1 μm in diameter and spherical particles smaller than 50 nm that show a tendency to agglomerate and form larger particles exhibiting a sponge-like structure. The formation of Mg₂FeH₆ takes place at the phase boundary between Fe seeds and the growing hydride phase. In contrast, the decomposition of the Mg₂FeH₆ phase takes place with the formation of the separate nanosized Mg and Fe phases. The dehydrogenated powder sample shows oval Fe precipitates of 10–100 nm in size that are embedded in the Mg-based matrix.     

Effect of in-situ formed Mg2Ni/Mg2NiH4 compounds on hydrogen storage performance of MgH2

Magnesium-based hydrogen storage materials (MgH₂) are promising hydrogen carrier due to the high gravimetric hydrogen density; however, the undesirable thermodynamic stability and slow kinetics restrict its utilization. In this work, we assist the de/hydrogenation of MgH₂ via in situ formed additives from the conversion of an MgNi₂ alloy upon de/hydrogenation. The MgH₂–16.7 wt%MgNi₂ composite was synthesized by ball milling of Mg powder and MgNi₂ alloy followed by a hydrogen combustion synthesis method, where most of the Mg converted to MgH₂, and the others reacted with the MgNi₂ generating Mg₂NiH₄, which produced in situ Mg₂Ni during dehydrogenation. Results showed that the Mg₂Ni and Mg₂NiH₄ could induce hydrogen absorption and desorption of the MgH₂, that it absorbed 2.5 wt% H₂ at 473 K, much higher than that of pure Mg, and the dehydrogenation capacity increased by 2.6 wt% at 573 K. Besides, the initial dehydrogenation temperature of the composite under the promotion of Mg₂NiH₄ decreased greatly by 100 K, whereas it is 623 K for MgH₂. Furthermore, benefiting from the catalyst effect of Mg₂NiH₄ during dehydrogenation, the apparent activation energy of the composite reduced to 73.2 kJ mol⁻¹ H₂ from 129.5 kJ mol⁻¹ H₂.     

Enhanced hydrogen desorption/absorption properties of magnesium hydride with CeF3@Gn

In order to improve the hydrogen storage performance of MgH₂, graphene and CeF₃ co-catalyzed MgH₂ (hereafter denoted as MgH₂+CeF₃@Gn) were prepared by wet method ball milling and hydriding, which is a simple and time-saving method. The effect of CeF₃@Gn on the hydrogen storage behavior of MgH₂ was investigated. The experimental results showed that co-addition of CeF₃@Gn greatly decreased the hydrogen desorption/absorption temperature of MgH₂, and remarkably improved the dehydriding/hydriding kinetics of MgH₂. The onset hydrogen desorption temperature of Mg + CeF₃@Gn is 232 °C，which is 86 °C lower than that of as-milled undoped MgH₂, and its hydrogen desorption capacity reaches 6.77 wt%, which is 99% of its theoretical capacity (6.84 wt%). At 300 °C and 200 °C the maximum hydrogen desorption rates are 79.5 and 118 times faster than that of the as-milled undoped MgH₂. Even at low temperature of 150 °C, the dedydrided sample (Mg + CeF₃@Gn) also showed excellent hydrogen absorption kinetics, it can absorb 5.71 wt% hydrogen within 50 s, and its maximum hydrogen absorption rate reached 15.0 wt% H₂/min, which is 1765 times faster than that of the undoped Mg. Moreover, no eminent degradation of hydrogen storage capacity occurred after 15 hydrogen desorption/absorption cycles. Mg + CeF₃@Gn showed excellent hydrogen de/absorption kinetics because of the MgF₂ and CeH_2-3 that are formed in situ, and the synergic catalytic effect of these by-products and unique structure of Gn.     

Hydrogen storage performance of 5LiBH4 + Mg2FeH6 composite system

The hydrogen storage properties of 5LiBH₄ + Mg₂FeH₆ reactive hydride composites for reversible hydrogen storage were investigated by comparing with the 2LiBH₄ + MgH₂ composite in the present work. The dehydrogenation pathway and reaction mechanism of 5LiBH₄ + Mg₂FeH₆ composite were also investigated and elucidated. The self-decomposition of Mg₂FeH₆ leads to the in situ formation of Mg and Fe particles on the surface of LiBH₄, resulting in a well dispersion between different reacting phases. The formation of FeB is observed during the dehydrogenation of 5LiBH₄ + Mg₂FeH₆ composite, which might supplies nucleation sites of MgB₂ during the dehydrogenation process, but is not an ascendant catalyst for the self-decomposition of LiBH₄. And FeB can also transform to the LiBH₄ and Fe by reacting with LiH and H₂ during the rehydrogenation process. The dehydrogenation capacity for 5LiBH₄ + Mg₂FeH₆ composite still gets to 6.5 wt% even after four cycles. The X-ray diffraction analyses reveal the phase transitions during the hydriding and dehydriding cycle. The formed FeB in the composite maintains a nanostructure after four hydriding-dehydriding cycles. The loss of hydrogen storage capacity and de-/rehydrogenation kinetics can be attributed to the incomplete generation of Mg₂FeH₆ during the rehydrogenation process.     

Dual-tuning of de/hydrogenation kinetic properties of Mg-based hydrogen storage alloy by building a Ni-/Co-multi-platform collaborative system

The Mg-based hydrogen storage alloy with multiple platforms is successfully prepared by ball milling Co powder and Mg-RE-Ni precursor alloy, and its hydrogen storage behavior was investigated in detail by XRD, EDS, TEM, PCI, and DSC methods. The ball-milled alloy consists of the main phase Mg, the catalytic phases Mg₂Ni, Mg₂Co as well as a small amount of Mg₁₂Ce, and convert into the MgH₂–CeH_2.73-Mg₂NiH₄–Mg₂CoH₅ composite after hydrogenation. The composite has three PCI platforms corresponding to the reversible de/hydrogenation reaction of Mg/MgH₂, Mg₂Ni/Mg₂NiH₄ and Mg₆Co₂H₁₁/Mg₂CoH₅. Among them, the transformation between Mg₂Ni and Mg₂NiH₄ triggers the “spill-over” effect which promote the decomposition of MgH₂ phases and enhances the hydrogen desorption kinetics. Meanwhile, the conversion of the Mg₆Co₂H₁₁ to Mg₂CoH₅ phase induces the “chain reaction” effect, which leads to preferential nucleation of Mg phase and improves the hydrogen absorption kinetics. Therefore, the Mg-RE-Ni-Co alloy has a double improvement on hydrogen absorption and desorption kinetics. Concretely, the alloy has an optimal hydrogen absorption temperature of 200 °C, at which it can absorb 5.5 wt. % H₂ within 40 s. Under the conditions, the capacity of absorption almost reaches the maximum reversible value (about 5.6 wt. %). Besides, the alloy has a dehydrogenation activation energy of 67.9 kJ/mol and can desorb 5.0 wt. % H₂ within 60 min at the temperature of 260 °C.     

Effective synthesis of Mg2CoH5 by reactive mechanical milling and its hydrogen sorption behavior after cycling

Mg₂CoH₅ was synthesized by reactive mechanical milling (RMM) under hydrogen atmosphere (0.5 MPa) from 2MgH₂–Co and 3MgH₂–Co mixtures, with a yield >80%. The microstructure, structure and thermal behavior of the phases formed during the processing were investigated by transmission electron microscopy, X-ray diffraction and differential scanning calorimetry. Kinetic properties of the reaction with hydrogen of the 2MgH₂–Co and 3MgH₂–Co mixtures after RMM were evaluated using modified Sieverts-type equipment. The 3MgH₂–Co mixture showed better properties for storage applications, with its highest rate of hydrogen absorption and desorption at 300 °C, its storage capacity of about 3.7 wt% in less than 100 s, and good stability after cycling. Although the starting material presents Mg₂CoH₅ as majority phase, the cycling leads to disproportion between Mg and Co. We obtained a mixture of Mg₂CoH₅, Mg₆Co₂H₁₁ and MgH₂ hydrides, as well as other phases such as Co and/or Mg, depending on experimental conditions.     

Determination of kinetic parameters and hydrogen desorption characteristics of MgH2-10 wt% (9Ni–2Mg–Y) nano-composite

Hydrogen desorption kinetic parameters of MgH₂ compounds were measured and compared with published gas solid reaction models. The compounds investigated in this study were as-received MgH₂, ball milled MgH₂, and MgH₂ ball milled with 9Ni–2Mg–Y catalyst compound. It was determined that different models were necessary to fit the hydrogen desorption data collected at different temperatures on the same sample, indicating that desorption mechanisms changed with respect to temperature. Addition of (9Ni–2Mg–Y) alloy as a catalyst to MgH₂ increased the hydrogen desorption capacity of MgH₂ from zero (for as-received MgH₂) to about 5 wt% at 350 °C within 500 s. The activation energy value was determined as 187 kJ/mol H₂ for the as-received MgH₂, 137 kJ/mol H₂ for 20 h ball milled MgH₂, and 62 kJ/mol H₂ for 20 h ball milled MgH₂-10 wt% (9Ni–2Mg–Y) nano-composite by the Arrhenius and Kissinger methods. Moreover, the integral heat of H₂ desorption for the MgH₂-10 wt% (9Ni–2Mg–Y) nano-composite was measured to be about 78 ± 0.5 kJ/mol H₂ by adsorption micro-calorimetry consistent with the results of the Arrhenius and Kissinger methods.     

Integrated Ni/Nb2O5 nanocatalytic agent dose for improving the hydrogenation/dehydrogenation kinetics of reacted ball milled MgH2 powders

Reactive ball milling (RBM) technique was employed to synthesize ultrafine powders of MgH₂, using high energy ball mill operated at room temperature under 50 bar of a hydrogen gas atmosphere. The MgH₂ powders obtained after 200 h of continuous RBM time composed of β and γ phases. The powders possessed nanocrystalline characteristics with an average grain of about 10 nm in diameter. The time required for complete hydrogen absorption and desorption measured at 250 °C was 500 s and 2500 s, respectively. In order to improve the hydrogenation/dehydrogenation kinetics of as synthesized MgH₂ powders, three different types of nanocatalysts (metallic Ni, Nb₂O₅ and (Ni)_x/(Nb₂O₅)_y) were utilized with different weight percentages and independently ball milled with the MgH₂ powders for 50 h under 50 bar of a hydrogen gas atmosphere. The results showed that the prepared nanocomposite MgH₂/5Ni/5Nb₂O₅ powders possessed superior hydrogenation/dehydrogenation characteristics, indexed by low values of activation energy for β-phase (68 kJ/mol) and γ-phase (74 kJ/mol). This nanocomposite system showed excellent hydrogenation/dehydrogenization behavior, indexed by the short time required to uptake (41 s) and release (121 s) of 5 wt% H₂ at 250 °C. At this temperature the synthesized nanocomposite powders possessed excellent absorption/desorption cyclability of 180 complete cycles. No serious degradation on the hydrogen storage capacity could be detected and the system exhibited nearly constant absorption and desorption values of +5.46 and −5.46 wt% H₂, respectively.