掺混比例和喷射定时对二甲醚-乙醇发动机燃烧和排放的影响

在一台电控共轨发动机上,试验研究了乙醇掺混比例和喷射定时对二甲醚-乙醇混合燃料燃烧及排放的影响。结果表明:随乙醇比例的增加,滞燃期延长,燃烧持续期缩短,最大压力升高率上升。随喷射推迟,滞燃期延长,燃烧相位延后,燃烧持续期在纯二甲醚时延长,而在掺混乙醇时则先延长后缩短,最大压力升高率先下降后上升。掺混乙醇和推迟喷射使预混燃烧比例增加。随喷射推迟,混合燃料的排气温度升高,喷射推迟到上止点后,排气温度随乙醇比例的增加而升高,排气温度高,则废气能量高,增压器增压比大,进气流量大,导致缸内压缩压力升高。在上止点前喷射时,掺混乙醇能使HC和CO排放保持在较低范围的同时,一定程度降低NO_x排放,掺混15%的乙醇较纯二甲醚最大降低约11%NO_x排放。随推迟喷射,NO_x排放降低,最大降幅达52%,在过分推迟燃料喷射时,因热效率低,循环喷射量增加,含15%乙醇混合燃料的NO_x排放会高于纯二甲醚。HC和CO排放随喷射推迟而升高,且升高幅度增大。     

Effects of direct water injection on engine performance in a hydrogen (H2)-fueled engine at varied amounts of injected water and water injection timing

In this paper, the effects of direct water injection (WI) on characteristics of combustion and emission for a hydrogen (H₂)-fueled spark ignition (SI) engine were experimentally investigated. The experiments conducted under different amounts of water injection (AWI) and varied water injection timing (WIT). The experimental results showed that in-cylinder pressure decreased, indicated thermal efficiency (ITE) increased, and the flame development (CA0-10) and propagation (CA10-90) periods prolonged when AWI raised. When AIW grew to 4.5 mg/cycle, Nitrogen oxides (NOx) expelled from the original engine decreased by 53.7% when excess air ratio (λ) was 1.15. Early WIT had positive effects on the reduction of NOx emissions. When WIT retarded, in-cylinder pressure increased, ITE decreased and CA0-10 and CA10-90 shortened, NOx emissions rapidly increased.     

Study on combustion and emission characteristics of a n-butanol engine with hydrogen direct injection under lean burn conditions

The n-butanol fuel, as a renewable and clean biofuel, could ease the energy crisis and decrease the harmful emissions. As another clean and renewable energy, hydrogen properly offset the high HC emissions and the insufficient of dynamic property of pure n-butanol fuel in SI engines, because of the high diffusion coefficient, high adiabatic flame velocity and low heat value. Hydrogen direct injection not only avoids backfire and lower intake efficiency but also promotes to form in-cylinder stratified mixture, which is helpful to enhance combustion and reduce emissions. This experimental study focused on the combustion and emissions characteristics of a hydrogen direct injection stratified n-butanol engine. Three different hydrogen addition fractions (0%, 2.5%, 5%) were used under five different spark timing (10° ,15° ,20° ,25° ,30° CA BTDC). Engine speed and excess air ratio stabled at 1500 rpm and 1.2 respectively. The direct injection timing of the hydrogen was optimized to form a beter stratified mixture. The obtained results demonstrated that brake power and brake thermal efficiency are increased by addition hydrogen directly injected. The BSFC is decreased with the addition of hydrogen. The peak cylinder pressure and the instantaneous heat release rate raises with the increase of the hydrogen addition fraction. In addition, the HC and CO emissions drop while the NOx emissions sharply rise with the addition of hydrogen. As a whole, with hydrogen direct injection, the power and fuel economy performance of n-butanol engine are markedly improved, harmful emissions are partly decreased.     

Effect of fuel injection timing and injection pressure on performance in a hydrogen direct injection engine

The in-cylinder hydrogen fuel injection method (diesel engine) induces air during the intake stroke and injects hydrogen gas directly into the cylinder during the compression stroke. Fundamentally, because hydrogen gas does not exist in the intake pipe, backfire, which is the most significant challenge to increasing the torque of the hydrogen port fuel injection engine, does not occur. In this study, using the gasoline fuel injector of a gasoline direct-injection engine for passenger vehicles, hydrogen fuel was injected at high pressures of 5 MPa and 7 MPa into the cylinder, and the effects of the fuel injection timing, including the injection pressure on the output performance and efficiency of the engine, were investigated. Strategies for maximizing engine output performance were analyzed.The fuel injection timing was retarded from before top dead center (BTDC) 350 crank angle degrees (CAD) toward top dead center (TDC). The minimum increase in the best torque ignition timing improved, and the efficiency and excess air ratio increased, resulting in an increase in torque and decrease in NO_x emissions. However, the retardation of the fuel injection timing is limited by an increase in the in-cylinder pressure. By increasing the fuel injection pressure, the torque performance can be improved by further retarding the fuel injection timing or increasing the fuel injection period. The maximum torque of 142.7 Nm is achieved when burning under rich conditions at the stoichiometric air-fuel ratio.     

Numerical study on effects of hydrogen direct injection on hydrogen mixture distribution,combustion and emissions of a gasoline/hydrogen SI engine under lean burn condition

A numerical study on effects of hydrogen direct injection on hydrogen mixture distribution, combustion and emissions was presented for a gasoline/hydrogen SI engine. Under lean burn conditions, five different direct hydrogen injection timings were applied at low speeds and low loads on SI engines with direct hydrogen injection (HDI) and gasoline port injection. The results were showed as following: firstly, with the increase of hydrogen direct injection timing, the hydrogen concentration near the sparking plug first increases and then decreases, reaching the highest when hydrogen direct injection timing is 120°CA BTDC: Secondly, hydrogen can speed up the combustion rate. The main factor affecting the combustion rate and efficiency is the hydrogen concentration near the sparking plug: Thirdly, in comparing with gasoline, the NO_X emissions with hydrogen addition increase by an average of 115%. For different hydrogen direct injection timings, the NO_X emissions of 120°CA BTDC is the highest, which is 29.9% higher than the 75°CA BTDC. The hydrogen addition make the NO_X emissions increase in two ways. On the one hand, the average temperature with hydrogen addition is higher. On the other hand, the temperature with hydrogen addition is not homogeneous, which makes the peak of temperature much higher. In a word, the main factor of NO_X emissions is the size of high temperature zone in the cylinder: Finally, because the combustion is more complete, in comparing with gasoline, hydrogen addition can reduce the CO and HC emissions by 32.2% and 80.4% respectively. Since a more homogeneous hydrogen mixture distribution can influence a lager zone in the cylinder and reduce the wall quenching distance, these emissions decrease with the increase of hydrogen direct injection timing. The CO and HC emissions of 135°CA BTDC decrease by 41.5% and 71.4%, respectively, compared to 75°CA BTDC.     

喷射参数对二甲醚PPCCI发动机燃烧与排放特性的影响

在一台6缸增压电控共轨二甲醚发动机上进行试验,研究了预喷时刻、预喷燃料量、喷射压力、主喷时刻等喷射参数对二甲醚部分预混合充量压缩燃烧(PPCCI)发动机燃烧与排放特性的影响。试验结果表明:随预喷时刻提前,缸内压力峰值降低,二甲醚发动机缸内燃烧由两阶段放热转变为PPCCI三阶段放热,氮氧化物(NOx)排放显著降低,HC和CO排放升高;随预喷射燃料量增加,缸内压力峰值及预混合燃烧的冷焰反应和热焰反应速率明显增大,NOx排放逐渐降低,HC和CO排放显著升高;随喷射压力降低,预混合燃烧热焰反应速率增加,主喷扩散燃烧始点推迟,扩散燃烧放热率峰值和NOx排放明显降低,HC和CO排放升高;随主喷时刻推迟,预喷预混合燃烧几乎没有变化,主喷扩散燃烧延后,缸内压力峰值和放热率峰值降低,NOx排放显著降低,HC和CO排放升高。     

Emission and performance estimation in hydrogen injection strategies on diesel engines

Recently, the increasing demand for energy requires the use of alternative fuels, especially in fossil fueled power systems. As a promising alternative fuel for next-generation diesel engines that utilize fossil fuel, hydrogen fuel is one step ahead due to its positive properties. In this study, the effects of hydrogen on the performance of a diesel engine have been numerically investigated with respect to different injection ratios and timings. The numerical results of the study for 25% load conditions on a single-cylinder, four-stroke diesel engine have been validated against experimental data taken from literature and good agreement has been observed for pressure results. Emission parameters such as NO_x, CO and performance parameters such as cylinder temperature, pressure, power, thermal efficiency and IMEP are presented comparatively.The results of numerical analyses show that the maximum pressure, temperature and heat release rate are observed with injection ratio of H15 and early injection timing (20° CA BTDC). Besides that, engine power, thermal efficiency and IMEP are greatly improved with increasing injection ratio and early injection timing. Although combustion chamber performance parameters improve with rising the hydrogen injection ratio, higher NO_x emissions have also been detected as a negative side effect. Furthermore, while early injection timing increases diesel engine performance, it also causes an increase in NO_x emissions. Therefore, precise determination of injection timing together with the optimum amount of hydrogen has revealed that it brings crucial improvement in engine performance and emissions.     

推迟供油提前角对生物柴油发动机燃烧和排放性能的影响

在直喷式增压柴油机上进行了供油提前角对生物柴油发动机动力性、经济性和排放性能影响的研究。试验结果表明:与柴油相比,推迟供油提前角后生物柴油的动力性下降,燃油经济性恶化,NO_x和烟度排放均有不同程度的降低。推迟供油提前角对生物柴油的喷油压力和滞燃期影响不大,但喷油始点和燃烧始点均迟于柴油。与柴油相比,推迟供油提前角后最高气缸压力下降,放热峰值出现时刻提前,指示热效率降低。燃烧始点与NO_x排放的相关性最大,喷油始点和放热峰值出现时刻也与NO_x排放呈弱相关性。     

预喷正时对柴油机燃烧与排放影响的试验研究

通过台架试验,分析对比柴油机各参数随预喷正时的变化,研究多次喷射预喷正时对柴油机燃烧和排放性能的影响。试验表明,预喷正时决定缸内燃烧的放热始点和放热率,影响缸内的燃烧温度、爆发压力、NOx排放和碳烟的生成,预喷正时为20°时,爆发压力最大;预喷正时为35°时,热效率最高,油耗率和烟度最低;预喷正时为45°时,NOx排放最小。综合分析选择预喷正时40°作为折中优化方案,降低发动机油耗和NOx、碳烟排放,同时提高发动机的热效率。     

Effects of second hydrogen direct injection proportion and injection timing on combustion and emission characteristics of hydrogen/n-butanol combined injection engine

Hydrogen and n-butanol are superior alternative fuels for SI engines, which show high potential in improving the combustion and emission characteristics of internal combustion engines. However, both still have disadvantages when applied individually. N-butanol fuel has poor evaporative atomization properties and high latent heat of vaporization. Burning n-butanol fuel alone can lead to incomplete combustion and lower temperature in the cylinder. Hydrogen is not easily stored and transported, and the engine is prone to backfire or detonation only using hydrogen. Therefore, this paper investigates the effects of hydrogen direct injection strategies on the combustion and emission characteristics of n-butanol/hydrogen dual-fuel engines based on n-butanol port injection/split hydrogen direct injection mode and the synergistic optimization of their characteristics. The energy of hydrogen is 20% of the total energy of the fuel in the cylinder. The experimental results show that a balance between dynamics and emission characteristics can be found using split hydrogen direct injection. Compared with the second hydrogen injection proportion (IP2) = 0, the split hydrogen direct injection can promote the formation of a stable flame kernel, shorten the flame development period and rapid combustion period, and reduce the cyclic variation. When the IP2 is 25%, 50% and 75%, the engine torque increases by 0.14%, 1.50% and 3.00% and the maximum in-cylinder pressure increases by 1.9%, 2.3% and 0.6% respectively. Compared with IP2 = 100%, HC emissions are reduced by 7.8%, 15.4% and 24.7% and NOx emissions are reduced by 16.4%, 13.8% and 7.9% respectively, when the IP2 is 25%, 50% and 75%. As second hydrogen injection timing (IT2) is advanced, CA0-10 and CA10-90 show a decreasing and then increasing trend. The maximum in-cylinder pressure rises and falls, and the engine torque gradually decreases. The CO emissions show a trend of decreasing and remaining constant. However, the trends of HC emissions and NOx emissions with IT2 are not consistent at different IP2. Considering the engine's dynamics and emission characteristics, the first hydrogen injection proportion (IP1) = 25% plus first hydrogen injection timing (IT1) = 240°CA BTDC combined with IP2 = 75% plus IT2 = 105°CA BTDC is the superior split hydrogen direct injection strategy.     

Combined effect of injection timing,EGR and injection pressure in reducing the NOx emission of a biodiesel blend

In this study, an attempt was made to reduce the higher oxides of nitrogen (NO_x) emission of a crude rice bran oil methyl ester (CRBME) blend through modification of combustion process by retarding fuel injection timing and exhaust gas recirculation at an increased fuel injection pressure. At modified condition, delay period and peak pressure of CRBME blend were lower than those at normal condition. The occurrence of maximum heat release rate retarded with a higher magnitude when compared with normal condition. Experimental results show that as a result of combustion modification, NO_x and carbon monoxide emissions were reduced significantly with marginal increase in smoke density. Brake thermal efficiency and unburnt hydrocarbon emissions of the engine were increased significantly as a result of this modification process. This investigation shows that the NO_x emission of a biodiesel blend can be reduced with less sacrifice on smoke density and increase in the brake thermal efficiency by modifying the combustion process.     

Effects of split injection proportion and the second injection timings on the combustion and emissions of a dual fuel SI engine with split hydrogen direct injection

In this paper, a new kind of injection mode, split hydrogen direct injection, was presented for a dual fuel SI engine. Six different first injection proportions (IP1) and five different second injection timings were applied at the condition of excess air ratio of 1, first injection timing of 300°CA BTDC, low speed, low load conditions and the Minimum spark advance for Best Torque (MBT) on a dual fuel SI engine with hydrogen direct injection (HDI) plus port fuel injection (PFI). The result showed that, split hydrogen direct injection can achieve a higher brake thermal efficiency and lower emissions compared with single HDI. In comparison with single HDI, the split hydrogen direct injection can form a controlled stratified condition of hydrogen which could make the combustion more complete and faster. By adding an early spray to form a more homogeneous mixture, the split hydrogen direct injection not only can help to form a flame kernel to make the combustion stable, but also can speed up the combustion rate through the whole combustion process, which can improve the brake thermal efficiency. By split hydrogen direct injection, the torque reaches the highest when the first injection proportion is 33%, which improves by 1.13% on average than that of single HDI. With the delay of second injection timing, the torque increases first and then decreases. With the increase of first injection proportion, the best second injection timing is advanced. Furthermore, by forming a more homogeneous mixture, the split hydrogen direct injection can reduce the quenching distance to reduce the HC emission and reduce the maximum temperature to reduce the NO_X. The split hydrogen direct injection can reduce the HC emission by 35.8%, the NO_X emissions by 7.3% than that of single HDI.     

船用直喷式天然气发动机喷射策略的优化

利用CONVERGE软件基于L23/30DF型船用天然气发动机建立了双天然气喷嘴、双引燃柴油喷嘴的直喷天然气发动机的缸内燃烧过程的CFD计算模型,计算了不同的柴油和天然气喷射时刻和间隔下发动机缸内燃烧和排放过程.结果 表明:引燃柴油的喷射时刻及其与天然气喷射时刻的间隔,对直喷式天然气发动机燃烧和排放性能有重要影响.当喷...     

某GDI发动机二次喷油策略的试验研究

本文研究了某汽油机缸内直喷(Gasoline Direct Injection,GDI)发动机二次喷油策略对自然吸气直喷发动机燃烧性能、经济性和排放性的影响规律,优化了二次喷射比例和时刻,为该类型发动机相关参数优化提供了数据积累和依据.试验工况下,随着二次喷油比例的增加,燃烧质量变差,缸内爆发压力降低,缸内燃烧温度降低...     

An experimental study on performance,emission and combustion parameters of hydrogen fueled spark ignition engine with the timed manifold injection system

In the present study, a single cylinder spark ignition (SI) engine is modified to operate with hydrogen gas with ECU (Electronic Controlled Unit) operated timely manifold injection system. Performance, emission and combustion parameters are studied at MBT (Maximum Brake Torque) spark timing with WOT (Wide Open Throttle) position. All trials are performed in the speed range of 1100 rpm–1800 rpm. Baseline observations are recorded with gasoline for comparison purpose. Results have shown that maximum brake power is reduced by 19.06% and peak brake thermal efficiency is increased by 3.16% in the case of hydrogen operation. Reduction in NO_x emission is observed for hydrogen at higher engine speed. The maximum net heat release rate is two times higher and the peak cylinder pressure is 1.36 times higher for hydrogen as compared to gasoline at the engine speed of 1400 rpm.     

Experimental study of stratified lean burn characteristics on a dual injection gasoline engine

Due to increasingly stringent fuel consumption and emission regulation, improving thermal efficiency and reducing particulate matter emissions are two main issues for next generation gasoline engine. Lean burn mode could greatly reduce pumping loss and decrease the fuel consumption of gasoline engines, although the burning rate is decreased by higher diluted intake air. In this study, dual injection stratified combustion mode is used to accelerate the burning rate of lean burn by increasing the fuel concentration near the spark plug. The effects of engine control parameters such as the excess air coefficient (Lambda), direct injection (DI) ratio, spark interval with DI, and DI timing on combustion, fuel consumption, gaseous emissions, and particulate emissions of a dual injection gasoline engine are studied. It is shown that the lean burn limit can be extended to Lambda= 1.8 with a low compression ratio of 10, while the fuel consumption can be obviously improved at Lambda= 1.4. There exists a spark window for dual injection stratified lean burn mode, in which the spark timing has a weak effect on combustion. With optimization of the control parameters, the brake specific fuel consumption (BSFC) decreases 9.05% more than that of original stoichiometric combustion with DI as 2 bar brake mean effective pressure (BMEP) at a 2000 r/min engine speed. The NO_x emissions before three-way catalyst (TWC) are 71.31% lower than that of the original engine while the particle number (PN) is 81.45% lower than the original engine. The dual injection stratified lean burn has a wide range of applications which can effectively reduce fuel consumption and particulate emissions. The BSFC reduction rate is higher than 5% and the PN reduction rate is more than 50% with the speed lower than 2400 r/min and the load lower than 5 bar.     

Research on combustion and emission characteristics of a hydrous ethanol/hydrogen combined injection spark ignition engine under lean-burn conditions

Ethanol, as one of the carbon-neutral fuels for spark ignition (SI) engine, has been widely used. Dehydration and purification of ethanol during production process will lead to high energy consumption. If hydrous ethanol can be directly applied to the engine, the cost of use will be greatly reduced. Due to the high latent heat of vaporization of ethanol and water, it is necessary to consider the performance of atomization, evaporation and combustion stability when hydrous ethanol is used in engine. As a zero-carbon fuel, hydrogen has excellent characteristics such as low ignition energy, fast flame propagation speed and wide combustion limit. The combination of hydrous ethanol and hydrogen can reduce the use cost and ensure better combustion performance. Therefore, this study explores the performance of hydrous ethanol/hydrogen in SI combined injection engine. The hydrous ethanol is injected into the intake port and the hydrogen is directly injected into the cylinder during the compression stroke. In this study, we firstly analyze the optimal water blending ratio (ω) of hydrous ethanol, which including 0, 3%, 6%, 9% and 12%. The experimental results show that the hydrous ethanol with 9% water ratio has the best performance without hydrogen addition. Based on the 9% water ratio, the effects of hydrogen blending ratio (0, 5%, 10%, 15% and 20%) on the combustion and emission under different excess air ratio (λ) (1, 1.1, 1.2, 1.3, 1.4). Hydrogen addition can increase the degree of constant volume combustion, so that the maximum cylinder pressure and temperature increase with the increase of the hydrogen blending ratio (HBR). When λ = 1.3 and HBR = 20%, the maximum in-cylinder pressure can be increased by 108.64% compared to pure hydrous ethanol. Hydrogen effectively increases the indicated mean effective pressure (IMEP) and reduces the coefficient of variation of IMEP (COV_IMEP). Adding hydrogen can reduce CO and HC emissions, while NO_x emissions will increase. When λ = 1.2 and HBR increasing from 0 to 20%, the NOx emissions increase by 106.75%, but it is still less than the NOx emissions of pure hydrous ethanol at λ = 1. On the whole, hydrogen direct injection can improve the combustion performance of hydrous ethanol and achieve stable combustion under lean-burn conditions.     

A coupling dynamics and thermodynamics study of diesel pilot-ignition injection effect on hydrogen combustion of a linear engine

Linear hydrogen engine is a new type of energy conversion device to supports variable compression ratio operation for clean emission. However, the new hydrogen engine using conventional spark ignition shows slow combustion speed and low thermal efficiency. This study makes a preliminary assessment to discuss the application of diesel pilot-ignition technology in linear hydrogen engine aiming to accelerate combustion and improve efficiency. A new coupling model between dynamics and thermodynamics is proposed and then iteratively calculated to give insight the interrelationship of combustion and motion in a diesel pilot-ignited linear hydrogen engine, while the effect of injection position on the hydrogen engine combustion is also investigated to make clear the feasibility of combustion optimization. The results indicate that the linear hydrogen engine is speeded by properly advancing the injection to promote combustion, and it has a positive effect on in-cylinder gas temperature, pressure and pressure rise rate, unless the injection is too early which results in higher NO emissions and aggravate the working intensity of the engine. In addition, the closer the fuel injection is to the top dead center, the incomplete combustion of hydrogen and diesel in the cylinder, the decrease of engine fuel economy and the increase of soot emissions. There is an optimal thermal efficiency of 40.7% for the LHE when it operates in the 0.8 mm injection position condition.     

可变喷油速率的超高压共轨系统喷射控制研究

通过AMESim软件建立了喷油速率可调的超高压共轨系统仿真模型,分析了相同喷油量条件下喷油率的变化特点。采用GT-Power软件建立单缸柴油机模型,将不同喷油率导入柴油机的燃烧计算模型,研究了不同喷油率对柴油机缸内压力、缸内温度、放热率、NO_x排放、碳烟排放及输出转矩和油耗率的影响。仿真结果表明:靴形喷油速率匹配合适的喷油提前角可优化柴油机的综合性能。搭建了超高压共轨柴油机台架,开展了不同喷油速率的喷射控制试验,结果表明:与相同油量条件下的高压共轨喷射相比,柴油机实施变喷油速率超高压喷射可获得更优异的动力性和燃油经济性,动力输出提高了5%,燃油消耗量下降了6%,碳烟排放降低,但NO_x排放升高。     

不同喷射时刻下缸内直喷天然气发动机的燃烧特性

开展了天然气高压缸内直喷发动机不同喷射时刻时的燃烧特性研究。研究结果表明：燃料喷射时刻对发动机性能及排放有较大影响,喷射太迟会导致天然气和空气混合时间短,混合效果差,燃烧持续期长,放热速率慢。喷射过早会导致充量系数下降,燃料容易进入燃烧室狭缝间隙处,造成较高的HC排放。对于给定转速,发动机存在一个最佳燃料喷射提前角,此时缸内最高压力值最大,最大压力升高率和最大放热率最大,放热速率快,燃烧过程等容度好,火焰发展期、快速燃烧期和燃烧持续期短,发动机热效率高,HC、CO排放也维持较低水平。