Constructing an internally cross-linked structure for polysulfone to improve dimensional stability and alkaline stability of high performance anion exchange membranes

The preparation of quaternary ammonium polysulfone anion exchange membranes (AEMs) with good dimensional stability and alkaline stability is an urgent problem to solve. In response, a series of cross-linked based on polysulfone and 4, 4′-trimethylenedipiperidine (TMDP) as crosslinkers with different degrees AEMs were developed in this work through a simple process. Among the fabricated AEMs, CAPSF-5 exhibits superb alkaline stability in a 1 M KOH aqueous solution at 60 °C for 15 days, whereas the non-crosslinked APSF membrane became tremendously brittle within 24 h and could not be further studied under the same conditions. In addition, even at 60 °C, CAPSF-5 demonstrates a superior dimensional stability compared to the non-crosslinked APSF membrane due to the formation of a dense internal network structure. These observations demonstrate that crosslinked CAPSF membranes can be a viable strategy to improve the deficiency of the polysulfone backbone, especially in terms of alkaline stability.     

Preparation and characterization of imidazolium-based membranes for anion exchange membrane fuel cell applications

New anion exchange membranes (AEMs) with high conductivity, good dimensional and alkaline stability are currently required in order to develop alkaline fuel cells into efficient and clean energy conversion devices. In this study, a series of AEMs based on 1, 2-dimethyl-3-(4-vinylbenzyl) imidazolium chloride ([DMVIm][Cl]) are prepared and investigated. [DMVIm][Cl] is synthesized and used as ion carriers and hydrophilic phase in the membranes. The water uptake, swelling ratio, IEC and conductivity of the AEMs increase with increasing the [DMVIm][Cl]. The imidazolium-based AEMs show excellent thermal stability, sufficient mechanical strength, the membrane which containing 30% mass fraction of [DMVIm][Cl] shows conductivity up to 1.0 × 10^?2 S cm^?1 at room temperature and good long-term alkaline stability in 1 M KOH solution at 80 °C. The results of this study suggest that this type of AEMs have good perspectives for alkaline anion exchange membrane fuel cell applications.     

Bis-pyridinium crosslinked poly(ether ether ketone) anion exchange membranes with enhancement of hydroxide conductivity and alkaline stability

A series of tunable bis-pyridinium crosslinked PEEK-BiPy-x anion exchange membranes (AEMs) are prepared successfully to improve the “trade-off” between ionic conductivity and alkaline stability. The crosslinking density of bis-pyridinium is optimized to promote microphase separation and guarantee the free volume. All the PEEK-BiPy-x membranes have a distinct microphase separation pattern observed by atomic force microscopy (AFM) and the PEEK-BiPy-x membranes also display adequate thermal, mechanical and dimensional stability. Impressively, the PEEK-BiPy-0.5 membrane exhibits maximum tensile strength (58.53 MPa) and highest IEC of 1.316 mmol·g^?1. Meanwhile, its hydroxide conductivity reaches up to 70.86 mS·cm^?1 at 80 °C. Besides, great alkaline stability of PEEK-BiPy-0.5 membrane is obtained with conductivity retention of 91.74% after 1440 h in 1 M NaOH solution, owing to the crosslinked structure of the AEMs and steric effect of bis-pyridinium cations. Overall, the PEEK-BiPy-x membranes possess potential applications in AEMs.     

Improved conductivity and stability of anion exchange membranes by introducing steric hindrance and crosslinked structure

The alternating copolymer based on poly (ether ether ketone) (PEEK) is synthesized with ordered side chain. A series of novel anion exchange membranes grafte with the 1, 2-dimethylimidazole and 1-vinylimidazole are obtained. The copolymer was verified by ¹H NMR and the crosslinked membranes are further investigated by solvability test. The ordered hydrophilic side chains form well-defined microphase separation structure, which are proved by Transmission electron micrographs microscopy (TEM). The ionic conductivity is 0.075 S/cm at 80 °C of Im-PEEK-0 uncross-linked membrane. With the addition of 1-vinylimidazole, the maximum stress increases to 66.57 MPa, the water uptake drop to 17.1% and swelling ratio drop to 14.8% at 80 °C of Im-PEEK-0.3 membrane. The hydroxide conductivity remains 82.8% in 2 mol L⁻¹ NaOH solution at 60 °C for 400 h. Meanwhile, all the membranes exhibit excellent thermal stability. Overall, the ordered imidazolium-functionalized side chains provide a method to balance hydroxide conductivity and alkali stability of anion exchange membranes.     

Constructing micro-phase separation structure by multi-arm side chains to improve the property of anion exchange membrane

In order to improve the performance of anion exchange membrane (AEMs) as the core component of alkaline fuel cell, a novel pentamethyl-contained phenolphthalein multi-arm monomer is synthesized. The highly imidazolium-functionalized poly (arylene ether ketone) membrane (Im-PEK-x) are prepared by introducing 1,2-dimethylimidazole as hydrophilic segments. The monomer, polymer and anion exchange membranes are confirmed by ¹H NMR spectra. The well-defined micro-phase separated structure of membranes is conducive to ion transport and the structure is investigated by TEM and SAXS. The imidazolium-functionalized membranes (Im-PEK-0.8) exhibits high ionic conductivity (0.148 S/cm at 80 °C). The tensile strength of Im-PEK-0.8 membrane is 30.06 MPa. Furthermore, after immersing in 60 °C, 2 M NaOH solution for 240 h, the ionic conductivity remains 0.092 S/cm for Im-PEK-0.8. The 1,2-dimethylimidazole enhance alkaline stability by steric effect of the substituent group at the C2 position. All these results indicate that this is a new method to enhance conductivity and stability performance of AEMs.     

Facile construction of poly(arylene ether)s-based anion exchange membranes bearing pendent N-spirocyclic quaternary ammonium for fuel cells

Anion exchange membrane (AEM) fuel cells have received significant attention due to their low fuel permeability and the use of non-platinum catalysts. However, the development of AEMs with robust chemical stability and high conductivity is still a great challenge. Herein, we prepare a new type of partially fluorinated backbone bearing pendent N-spirocyclic quaternary ammonium (QA) cations via a facile Williamson reaction, which displays great potential for fuel cells. The integration of the two substructures (a fluorinated moiety into a polymer backbone and a pendent cation structure) is beneficial for the fabrication of a well-defined micro-phase separation structure, thereby facilitating the construction of a highly-efficient ion transporting pathway. Correspondingly, the resulting AEM (PAENQA-1.0), despite its a relatively low ionic exchange capacity (0.93 meq g⁻¹) demonstrates a conductivity of 63.1 mS cm⁻¹ (80 °C). Meanwhile, the constrained ring conformation of N-spirocyclic QA results in improved stability of the AEMs.     

Well-designed mono- and di-functionalized comb-shaped poly(2,6-dimethylphenylene oxide) based alkaline stable anion exchange membrane for fuel cells

To mitigate the membrane stabilities (dimensional and mechanical) and ionic properties, we report well functionalized hydrophilic and hydrophobic (responsible for stabilities) phase separated quaternized anion exchange membrane (AEM). The N,N,N,N-Tetramethyl-1,3-propanediamine quaternized AEM spliced with alkyl chain (DQCP-36) formed self-amassed morphology with larger ionic clusters. The most suitable optimized AEM (DQCP-36) demonstrated enhanced hydroxide ion conductivity (4.66 × 10^?2 S cm^?1), ion-exchange capacity (1.35 meq./g) and lower activation energy (11.52 kJ/mol). These AEMs showed self-amassed morphology (well balanced hydrophilic and hydrophobic domain) and excellent stabilities (thermal, alkaline and dimensional). Under harsh alkaline medium (2 M NaOH) at 60 °C, DQCP-36 AEM showed about 9% reduction in conductivity after 700 h treatment, and assessment to be a suitable candidate for alkaline fuel cells.     

Imidazolium functionalized block copolymer anion exchange membrane with enhanced hydroxide conductivity and alkaline stability via tailoring side chains

To develop polymer electrolyte membrane with both high hydroxide conductivity and good alkaline stability, series of poly(arylene ether sulfone)s block copolymers bearing varied imidazolium functionalized aromatic pendants are synthesized, and the relationship between ionic pendants and the membrane properties are investigated and discussed. Atomic force microscopy (AFM) results suggest that, the well-controlled block copolymers and pendent aromatic chain structures are responsible for the formation of the well-defined microphase-separated morphology which is benefit to construct highly conductive ionic transport channels in membrane. The membranes tethering longer imidazolium functionalized aromatic pendants (Im-DFDM-bPES) exhibit large hydroxide conductivity than those bearing shorter ones (Im-DFDB-bPES) in spite of their comparable IEC values, this is in accordance with their sizes of hydrophilic domains in membrane. Among the membranes, Im-DFDM-bPES-x7y32 with IEC of 1.30 mequiv g^?1 gives the highest hydroxide conductivity (34.2 and 98.7 mS cm^?1 at 25 and 80 °C, respectively). Besides, both Im-DFDM-bPES and Im-DFDB-bPES membranes exhibit high alkaline stability after aging under severe conditions (4 M NaOH at 80 °C) for 144 h, where the aged Im-DFDM-bPES and Im-DFDB-bPES give hydroxide conductivity remaining by 74.8%–77.2% and 64.5%–66.4%, mechanical properties with maximum stress of 47.36–51.30 MPa and 60.03–62.28 MPa, respectively, indicating good chemical stability of both imidazolium moiety and block copolymer backbone.     

Preparation and characterization of a polyvinyl alcohol grafted bis-crown ether anion exchange membrane with high conductivity and strong alkali stability

A new type of symmetrical bis-crown ether is prepared by connecting dibenzo-18-crown-6 ether on both sides of the chromotropic acid, and then grafting the aforementioned bis-crown ether onto polyvinyl alcohol matrix to prepare a series of anion exchange membranes (AEMs), which their have high conductivity and strong alkali stability. These synthesized membranes were named B-C_X%-P AEMs (x is the mass percentage of the symmetrical bis-crown ether (B–C)). Then, the chemical structure of aforementioned AEMs were verified by means of ¹H NMR, FT-IR and UV. Meanwhile, the OH⁻ conductivity, alkaline stability and single cell performance of the synthesized membrane were also investigated. The results revealed that the conductivity of B–C_30%-P membrane is the highest at 80 °C (235 mS cm⁻¹), and the power density is also the highest (197 mW cm⁻²), and the alkali stability of the membrane synthesized in this paper was also improved. The conductivity at 80 °C was only reduced by 4%, which was obtained by immersing the B–C_30%-P membrane immersed in 6 mol L⁻¹ KOH solution for 168 h, which the aforementioned results proved that the synthesized membrane in this research had excellent OH⁻ conductivity and alkaline stability.     

Novel anion exchange membrane with poly ionic liquid-confined hypercrosslinked polymer for enhanced anion conduction and stability

Hypercrosslinked polymer (HCP) holds great potential for utilization as novel anion exchange membrane (AEM) material due to their rich microporous structure and high thermal/chemical stability while remaining challenges due to lack of hydroxide carriers. Herein we report a novel strategy of fabricating poly ionic liquid (PIL)-confined HCP for ion transfer. PIL precursors are loaded into the pores of HCP and in-situ polymerized to prepare PIL@HCP, which is then incorporated into quaternized poly (2,6-dimethyl-1,4-phenylene oxide) (QAPPO) to fabricate composite membrane. The introduction of PIL provides high concentration of quaternary ammonium (QA) groups in the porous networks of HCP. And the organic components impart outstanding compatibility between PIL@HCP and QAPPO matrix. All these permit the formation of interconnected hydroxide transfer channels through the membranes. Especially, the rigid and hydrophobic HCP functions with steric hindrance effectively impedes the attack of hydroxide ions on QA groups and maintains structure stability. Accordingly, the PIL@HCP/QAPPO composite membrane with high ion exchange capacity (IEC) of 2.33 mmol g^?1 achieves a hydroxide conductivity of 98 mS cm^?1 (80 °C, 100% RH), 92% higher than that of QAPPO. Meanwhile, the area swelling degree of PIL@HCP/QAPPO reduces to 13.6% in comparison to QAPPO (25.7%) and its conductivity retains 88% after alkaline treatment.     

Novel poly(carbazole-butanedione) anion exchange membranes constructed by obvious microphase separation for fuel cells

To develop anion exchange membranes with excellent chemical stability and high performance. A series of quaternary ammonium functionalized (hydrophilic) hydrophobic rigid poly (carbazole-butanedione) (HOCB-TMA-x) anion exchange membranes were prepared, where x represents the percentage content of hydrophobic unit octylcarbazole (OCB). Due to the introduction of hydrophobic rigid unit octylcarbazole and hexyl flexible side chain, the hydrophilic-hydrophobic microstructure of AEMs was developed. The AEMs exhibit excellent overall performance, specifically the low swelling ratio HOCB-TMA-30 membrane exhibits the highest OH^? conductivity of 152.9 mS/cm at 80 °C. Furthermore, the ionic conductivity of AEM decreased by only 9.5% after 2250 h of immersion in 1 M NaOH. The maximum peak power density of a single cell with a current density of 4.38 A/cm² at 80 °C was 1.85 W/cm².     

Profile of extended chemical stability and mechanical integrity and high hydroxide ion conductivity of poly(ether imide) based membranes for anion exchange membrane fuel cells

We designed and synthesized a poly(ether imide) (PEI) membrane that has good chemical and mechanical stabilities. Alkalized PEI (A-PEI) membrane was fabricated by solution casting of chloromethylated PEI (CM-PEI) followed by quaternization and alkalization. The chemical structure of the synthesized polymers was verified by proton nuclear magnetic resonance (¹H NMR) and Fourier-transform infrared spectroscopy (FT-IR). Physiochemical properties of the membrane such as ion exchange capacity, water uptake, and swelling ratio were investigated. The membranes with a high degree of chloromethylation (DC) exhibited elevated hydroxide ion conductivity in range of 6.7–44.2 mS/cm at 90 °C under 100% relative humidity (RH). The hydrophilic-hydrophobic phase separation was verified by atomic force microscope (AFM) and small angle X-ray scattering (SAXS) measurements. Chemical stability was evaluated by measuring the durability of membranes while they were soaked in oxidative and alkaline solutions at 60 °C for 200 h.     

Polymeric ionic liquids and MXene synergistically improve proton conductivity and mechanical properties of polybenzimidazole-based high-temperature proton exchange membranes

A series of Polymeric ionic liquids (PILs) cross-linked amino polybenzimidazoles with MXene fillers were successfully prepared. By anion replacement of PILs, the OH^? of the system can interact with phosphoric acid (PA) to form H₂PO₄^? and HPO₄^2? to transfer protons, and the hydroxide existing on the surface of MXene is also conducive to the transfer of protons. Therefore, the synergistic effect of the two enables the membrane to have high proton conductivity with low PA absorption. Through the covalent cross-linking between PILs and PBI and the interaction between the oxygen-containing groups on the surface of MXene and the = N and –NH of imidazole, so the mechanical performance can be greatly improved. The proton conductivity of AmPBI-PIL-5-MXene-3 can reach 91.4 mS cm^?1 at 180 °C, which is twice that of pristine AmPBI. Moreover, the tensile stress after PA doping can reach 11.1 MPa, which is twice that of pristine AmPBI. Meanwhile, the power density of AmPBI-PIL-5-MXene-3 can reach 219 mW cm^?2 at 350 mA cm^?2, which is 1.8 times that of pristine AmPBI. In addition, there is no voltage loss after 100 h test at 160 °C and 200 mA cm^?2, which indicates the excellent stability of the membrane.     

Dense 1,2,4,5-tetramethylimidazolium-functionlized anion exchange membranes based on poly(aryl ether sulfone)s with high alkaline stability for water electrolysis

Anion exchange membranes with enough alkaline stability and ionic conductivity are essential for water electrolysis. In this work, a class of anion exchange membranes (PAES-TMI-x) with dense 1,2,4,5-tetramethylimidazolium side chains based on poly(aryl ether sulfone)s are prepared by aromatic nucleophilic polycondensation, radical substitution and Menshutkin reaction. Their chemical structure and hydrophilic/hydrophobic phase morphology are characterized by hydrogen nuclear magnetic resonance (¹H NMR) and atomic force microscope (AFM), respectively. The water uptake, swelling ratio and ionic conductivity for PAES-TMI-x are in the range of 23.8%–48.3%, 8.3%–14.3% and 18.22–96.31 mS/cm, respectively. These AEMs exhibit high alkaline stability, and the ionic conductivity for PAES-TMI-0.25 remains 86.8% after soaking in 2 M NaOH solution at 80 °C for 480 h. The current density of 1205 mA/cm² is obtained for the water electrolyzer equipped with PAES-TMI-0.25 in 2 M NaOH solution at 2.0 V and 80 °C, and the electrolyzer also has good operation stability at current density of 500 mA/cm². This work is expected to provide a valuable reference for the selection and design of cations in high-performance AEMs for water electrolysis.     

Improved conductivity and stability of anion exchange membrane modified with bi-phenylguanidinium bridged silsesquioxane

This work reports the design, fabrication and properties of 4,4′-oxydiphenylguanidinium-bridged-silsesquioxane (ODGBS) modified polysulfone anion exchange membrane (AEM). It was prepared by sol-gel polymerization of ODGBS in the network of cross-linked, quaternized polysulfone. With hydrophilic biphenylguanidinium and SiOSi moieties working synergistically, the ODGBS derived gel functions as a water “reservoir” in the membrane and thus gives rise to high water uptake, which facilitates hydroxide ion transport via a vehicular mechanism. High water uptake may also “dilute” hydroxide ion at the vicinity of cations and lessen the hydroxide attack on cations. Moreover, ODGBS does not contain β hydrogen atoms, thus reducing the likelihood of Hofmann elimination under hydroxide attack. Due to the above benefits, ODGBS modified AEM could exhibit an improved conductivity from 19 to 25 mS/cm² at 30 °C, and a conductivity retention of 85% when treated in 1 M NaOH at 60 °C for 120 h, higher than that of the un-modified AEM (72%). This work provides a new strategy for enhancing stability and conductivity of AEM.     

Macromolecular crosslink of imidazole functionalized poly(vinyl alcohol) and brominated poly(phenylene oxide) for anion exchange membrane with enhanced alkaline stability and ionic conductivity

Anion exchange membranes (AEMs) are important energy conversion device for fuel cell applications, where the overall redox reaction happened. Both alkaline stability and ionic conductivity should be considered in the long-term use of fuel cells. In this work, imidazole functionalized polyvinyl alcohol was designed as the functional macromolecular crosslinking agent to fabricate crosslinked AEMs with brominated poly(phenylene oxide) matrix. Benefitting from the macromolecular crosslinked structure, the membranes displayed enhanced ionic conductivity and alkaline stability at elevated temperature. Moreover, membrane with ion exchange capacity of 1.54 mmol/g displayed ionic conductivity of 78.8 mS/cm at 80 °C, and the conductivity could maintain 75% of the initial value after immersion in 1 M NaOH solution at 80 °C for 1000 h. Moreover, a peak power density of 105 mW/cm² was achieved when the assembled single cell with c-91 was operated at 60 °C. These results indicated that the construction of macromolecular crosslinked AEMs have great potential in the practical application of anion exchange membranes fuel cells.     

Facile preparation of poly (2,6-dimethyl-1,4-phenylene oxide)-based anion exchange membranes with improved alkaline stability

Traditional quaternary ammonium (QA)-type anion exchange membranes (AEMs) usually exhibit insufficient alkaline stability, which impede their practical application in fuel cells. To address this issue, a facile method for the simple and accessible preparation of QA-type AEMs with improved alkaline stability was developed in this study. A series of novel AEMs (QPPO-xx-OH) were prepared from commercially available poly (2,6-dimethyl-1,4-phenylene oxide) (PPO) and 3-(dimethylamino)-2,2-dimethyl-1-propanol, via a three-step procedure that included bromination, quaternization, and ion exchange. Scanning electron microscopy revealed that dense, uniform membranes were formed. These QPPO-xx-OH membranes exhibited moderate hydroxide conductivities with ranges of 4–15 mS/cm at 30 °C and 12–36 mS/cm at 80 °C. When tested at similar ion exchange capacity (IEC) levels, the IEC retentions of QPPO-xx-OH membranes were 16–22% higher than that of traditional PPO membranes containing benzyltriethylammonium ions, after immersed in 2 M NaOH aqueous solution at 60 °C for 480 h, and the QPPO-47-OH membrane displayed excellent alkaline stability with the IEC retention of 92% after 480 h. In addition, the QPPO-xx-OH membranes also exhibited robust mechanical properties (tensile strength up to 37.6 MPa) and good thermal stability (onset decomposition temperature up to 150 °C). This study provides a new and scalable method for the facile preparation of AEMs with improved alkaline stability.     

Cross-linked anion exchange membranes with flexible,long-chain,bis-imidazolium cation cross-linker

Herein, poly (phenylene) oxide (PPO)-based cross-linked anion exchange membranes (AEMs) with flexible, long-chain, bis-imidazolium cation cross-linkers are designed and synthesized. Although the cross-linked membranes possess high ion exchange capacity (IEC) values of up to 3.51–3.94 meq g⁻¹, they have a low swelling degree and good mechanical strength because of their cross-linked structure. Though the membranes with the longest flexible bis-imidazolium cation cross-linker (BMImH-PPO) possess the lowest IEC among these PPO-based AEMs, they show the highest conductivity (24.10 mS cm⁻¹ at 20 °C) and highest power density (325.7 mW cm⁻² at 60 °C) because of the wide hydrophilic/hydrophobic microphase separation in the membranes that promote the construction of ion transport channels, as confirmed by atom force microscope (AFM) images and the small angle X-ray scattering (SAXS) analyses. Furthermore, the BMImH-PPO samples exhibit good chemical stability (10% and 6% decrease in IEC and conductivity, respectively, in 2 M KOH at 80 °C for 480 h, and a 22% decrease in weight in Fenton's reagent at 60 °C for 120 h), making such cross-linked AEMs potentially applicable in alkaline anion exchange membrane fuel cells.     

Enhanced ionic conductivity of anion exchange membranes by grafting flexible ionic strings on multiblock copolymers

A new strategy to prepare high-conductivity anion exchange membranes (AEMs) is presented here. A series of phenolphthalein-based poly(arylene ether sulfone nitrile) multiblock AEMs has been synthesized by selectively grafting flexible ionic strings on hydrophilic segments to form ionic regions. Moreover, the phenolphthalein groups are introduced to force chains apart and create additional interchain spacing. In addition, the nitrile groups suspended on main chains are aimed at enhancing the anti-swelling behavior of as-prepared AEMs. Along these processes, well-defined phase separation has been attained, forming excellent ion-transport channels. The effective phase separation has been confirmed by atomic force microscopy. Finally, as-prepared AEMs exhibit a high hydroxide conductivity, ranging from 40.1 to 121.6 mS cm⁻¹ in the temperature range of 30–80 °C, and superior ionic conductivity to IEC ratio at 80 °C. Furthermore, excellent thermal stability and desirable mechanical strength have been rendered by as-prepared AEMs. However, the alkaline stability of as-prepared AEMs requires further optimization.     

Branched polybenzimidazole / polymeric ionic liquid cross-linked membranes with high proton conductivity and mechanical properties for HT-PEM applications

Branched polymers have unique three-dimensional dendritic structures, so they have received a lot of attention in the application of high temperature proton exchange membranes. In this work, we synthesize BOPBI-X (X = 3%, 6%, 9%) membranes with different branched ratios based on the synthesis of OPBI, due to the introduction of a rigid triazine structure with a larger free volume, the membranes could absorb more phosphoric acid (PA) while maintaining sufficient mechanical strength. Among them, the BOPBI-6% membrane obtains splendid comprehensive performance, when the PA doping level (ADL) is 9.55, it achieves a proton conductivity of 99.2 mS cm^?1 at 180 °C, which is 1.8 times higher than OPBI (54.8 mS cm^?1), and it performs well in long-term oxidation stability test after 144 h, it still has a mass retention rate of 90%. For the sake of further boost the performance of the membrane, cross-linkable polymeric ionic liquid (PIL) is introduced to the system. Among them, BOPBI-PIL-30% membrane has sufficient mechanical properties (5.50 ± 0.8 MPa), and the proton conductivity (146.9 mS cm^?1) at 180 °C is also excellent, so BOPBI-PIL-30% membrane is expected to be a promising candidate as HT-PEMs.