Facile synthesis of highly active monolithic water-separated W-doped Ni–Fe–P catalysts

A new type of highly active and cost-effective nanoporous W-doped Ni–Fe–P catalyst on nickel foam (NF) was synthesized by a facile electroless plating method. The W-doped Ni–Fe–P/NF catalysts exhibit extraordinary catalytic activity for hydrogen evolution reaction (HER) in alkaline media, capable of yielding a current density of −10 mA cm⁻² at an overpotential of only 68 mV. Furthermore, the catalysts also show efficient activity towards oxygen evolution reaction (OER) with an overpotential of 210 mV at j = 10 mA cm⁻² as well. The W-doped Ni–Fe–P/NF electrocatalyst exhibits a long-term durability over 13 h test.     

Effect of carbon content on Ni–Fe–C electrodes for hydrogen evolution reaction in seawater

Hydrogen evolution reaction (HER) on the Ni–Fe–C electrodes electrodeposited at current density ranging from 100 to 300 A/m², as well as their electrochemical properties in 3.5% NaCl solution at 90 °C and pH = 12, had been investigated by polarization measurements, EIS technique. It was shown that the carbon content and grain size of Ni–Fe–C coatings are affected by current density. In addition, the hydrogen evolution overpotential of Ni–Fe–C electrodes was related with carbon content and grain size. The Ni–Fe–C electrodes with optimum catalytic activity for the HER were found to contain the maximum carbon content 1.59% and the minimum grain size 3.4 nm. The results of a comparative analysis between carbon content and intrinsic activity are that carbon content plays an important role in intrinsic activity of Ni–Fe–C electrodes.     

Ni–Fe–B catalysts for NaBH4 hydrolysis

A series of Ni–Fe–B catalysts with different Fe/(Fe + Ni) molar ratios, used for the hydrolysis of NaBH₄, were prepared by chemical reduction of NiCl₂ and FeCl₃ mixed solution with NaBH₄. The measurements revealed that the catalysts with the molar ratio of Fe/(Fe + Ni) (30%) exhibited the highest catalytic activity, and the optimal reduction temperature is 348 K. In addition, the effects of the concentration of NaBH₄, NaOH and the hydrolytic temperature of NaBH₄ were discussed in detail. The results show that the reaction rate of hydrolysis first rises up and then goes down subsequently with the increase of NaBH₄ concentration, as well as the concentration of NaOH. The activation energy of the hydrolysis for Ni–Fe–B catalysts is fitted to 57 kJ/mol. The maximum value of hydrogen generation is 2910 ml/(min g) at 298 K.     

Electrochemical performance of crystalline Ni–Co–Mo–Fe electrodes obtained by mechanical alloying on the oxygen evolution reaction

Electro-active _Co30Ni70${\mathrm{Co}}_{30}{\mathrm{Ni}}_{70}$, _Co30Mo70${\mathrm{Co}}_{30}{\mathrm{Mo}}_{70}$, _Ni30Mo70${\mathrm{Ni}}_{30}{\mathrm{Mo}}_{70}$, _Co10Ni20Mo70${\mathrm{Co}}_{10}{\mathrm{Ni}}_{20}{\mathrm{Mo}}_{70}$, _Fe10Co30Ni60${\mathrm{Fe}}_{10}{\mathrm{Co}}_{30}{\mathrm{Ni}}_{60}$ and _Co10Fe30Ni60${\mathrm{Co}}_{10}{\mathrm{Fe}}_{30}{\mathrm{Ni}}_{60}$ wt% alloys have been prepared by mechanical alloying. The electrocatalytic behavior of obtained electrodes has been evaluated in 30 wt% KOH aqueous solutions as a function of different temperatures (298, 323 and 343 K) and overvoltages (η=200$\eta =200$, 300, 400 mV). The effect of Fe contamination during mechanical milling was also analyzed. The electrode performance was studied by cyclic voltammetry, ac–impedance and steady-state polarization techniques. Appreciable current values for oxygen evolution reactions (OER) were measured at Ni–Co–Mo–Fe electrodes produced by this technique. It was also found that the electrochemically formed Co and Fe oxides and/or hydroxides did not show an activity for OER as good as reported on hydrogen evolution reaction (HER). Tafel plots of preoxidized at 1 cycle and prolonged cycled (50 cycles) for _Co30Ni70${\mathrm{Co}}_{30}{\mathrm{Ni}}_{70}$, _Co30Mo70${\mathrm{Co}}_{30}{\mathrm{Mo}}_{70}$, _Ni30Mo70${\mathrm{Ni}}_{30}{\mathrm{Mo}}_{70}$, _Co10Ni20Mo70${\mathrm{Co}}_{10}{\mathrm{Ni}}_{20}{\mathrm{Mo}}_{70}$, _Fe10Co30Ni60${\mathrm{Fe}}_{10}{\mathrm{Co}}_{30}{\mathrm{Ni}}_{60}$ and _Co10Fe30Ni60${\mathrm{Co}}_{10}{\mathrm{Fe}}_{30}{\mathrm{Ni}}_{60}$ crystalline electrodes were very different, which might be related to changes in the surface enrichment of one or two of the alloy constituents. The Mo electrocatalytic effects seem to be more important on the OER at higher temperatures than those showed previously for HER. Molybdenum containing crystalline Co and Ni powders (_Co10Ni20Mo70)$({\mathrm{Co}}_{10}{\mathrm{Ni}}_{20}{\mathrm{Mo}}_{70})$ showed the best catalytic behavior for the OER.     

Hydrogen absorption characteristics of mechanically alloyed Ti–Zr–Ni and Ti–V–Ni powders

A first investigation into the production of amorphous and nanostructured Ti-based alloys with nominal compositions Ti_41.5Zr_41.5Ni₁₇, Ti₆₁Zr₂₂Ni₁₇, Ti_41.5V_41.5Ni₁₇ and Ti₆₁V₂₂Ni₁₇ by mechanical alloying (MA) technique is presented. This technique was adopted to produce alloys' powders with high fresh surface area that were active for hydrogen storage. Hydrogen absorption characteristics and structure changes in the alloys after hydrogenation were investigated. Gas phase hydrogenation of the Ti–Zr–Ni alloys, at 573 K and an initial hydrogen pressure of 2 MPa, exhibited good hydriding properties and started at a maximal rate without induction period with a hydrogenation capacity up to 1.2 wt%. However, hydriding of Ti–V–Ni alloys at the same conditions exhibited slower rates. The Ti₆₁V₂₂Ni₁₇ composition showed high hydrogen absorption capacity of 1.8 wt% and exceeded 4 wt% at 345 K. In addition, the Ti–V–Ni alloys showed structure stability after hydrogenation and retained the amorphous structure.     

One-step electrodeposition of cauliflower-like Ni–Fe–Sn particles as a highly-efficient electrocatalyst for the hydrogen evolution reaction

Herein, a Ni–Fe–Sn coating was synthesized in-situ on Ni mesh by one-step electrodeposition at different durations. The Ni–Fe–Sn60 electrode obtained after 1 h deposition exhibits cauliflower-like morphology and the best electrocatalytic properties for the hydrogen evolution reaction (HER) compared to other electrodes. The electrode requires an overpotential of 43 mV at a current density of 10 mA cm⁻² and a small Tafel slope of 70 mV dec⁻¹ in a 1 M KOH solution. Moreover, the electrode shows outstanding stability in prolonged electrolysis and overall water splitting performance, generating a current density of 93 mA cm⁻² at 1.8 V, which is thrice that of an industry electrode. This electrocatalytic activity is ascribed to the high active surface area produced by the cauliflower-like Ni–Fe–Sn particles and the synergistic interaction of Ni, Fe and Sn. The simple synthesis method and excellent performance endow this electrode with great potential for large-scale applications.     

Influence of Pd addition on the electrochemical performance of Mg–Ni–Ti–Al-based metal hydride for Ni–MH batteries

Amorphous Mg_0.9Ti_0.1NiAl_0.05 and Mg_0.9Ti_0.1NiAl_0.05Pd_0.1 alloys were prepared by high energy ball milling and evaluated as metal hydride electrodes for Ni–MH batteries. The Mg_0.9Ti_0.1NiAl_0.05Pd_0.1 alloy showed a much higher cycle life with a capacity retention of 72% after 100 cycles (C_100th = 288 mAh g⁻¹) compared to 26% for the Pd-free alloy (C_100th = 117 mAh g⁻¹). This was mainly attributed to the improvement of the alloy oxidation resistance in KOH electrolyte with Pd addition, as confirmed by cyclic voltammetry experiments and X-ray diffraction analyses on cycled electrodes. In addition, in situ acoustic emission (AE) measurements revealed that the energy of the AE signals related to the particle cracking is lower for the Mg_0.9Ti_0.1NiAl_0.05Pd_0.1 electrode, suggesting that the cracks are smaller in size than with the Pd-free alloy. The Mg_0.9Ti_0.1NiAl_0.05Pd_0.1 electrode also displayed a higher discharge rate capability than the Mg_0.9Ti_0.1NiAl_0.05 electrode. On the basis of their respective electrochemical pressure–composition isotherm, it was shown that the presence of Pd in the alloy decreases the thermodynamic stability of the metal hydride. Through a comparative analysis of discharge polarization curves, it was also shown that Pd addition decreases substantially the H-diffusion resistance in the alloy whereas its positive effect on the charge-transfer resistance is limited.     

Insight into the role of sulfur in increasing intrinsic activity of Ni–Fe for efficient water splitting electrocatalysis

It is of great significance to explore and design low-cost and efficient electrocatalysts for the storage and conversion of intermittent renewable resources to clean hydrogen by water splitting. Herein, the amorphous Ni–Fe–S electrocatalysts are rapidly synthesized on Cu sheets and Ni foams using the simple electrodeposition method. After optimizing the S concentration, the Ni–Fe–S electrocatalysts exhibit the simultaneously boosted hydrogen and oxygen evolution reaction performances compared to the as-synthesized Ni–Fe and Ni. In addition, the Ni–Fe–S electrocatalysts as the bifunctional electrodes only require a cell voltage of 1.584 V (on Ni foam) and 1.705 V (on Cu sheet) to reach 10 mA/cm² with excellent stability in the electrocatalytic activity and surface properties. The results exhibit that the enhanced electrocatalytic activity can be attributed to the role of the doped S in formatting the amorphous structure, improving the hydrophilic and aerophobic properties, optimizing the electronic structure as well as enhancing the electrochemically active sites. This work might offer a new insight into the design of the cheap and highly efficient electrodes for generation of hydrogen by water splitting.     

One-step synthesis of amorphous Ni–Fe–P alloy as bifunctional electrocatalyst for overall water splitting in alkaline medium

Design of inexpensive and highly efficient bifunctional electrocatalyst is paramount for overall water splitting. In this study, amorphous Ni–Fe–P alloy was successfully synthesized by one-step direct-current electrodeposition method. The performance of Ni–Fe–P alloy as a bifunctional electrocatalyst toward both hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) was evaluated in 30 wt% KOH solution. It was found that Ni–Fe–P alloy exhibits excellent HER and OER performances, which delivers a current density of 10 mA cm^?2 at overpotential of ～335 mV for HER and ～309 mV for OER with Tafel slopes of 63.7 and 79.4 mV dec^?1, respectively. Moreover, the electrolyzer only needs a cell voltage of ～1.62 V to achieve 10 mA cm^?2 for overall water splitting. The excellent electrocatalytic performance of Ni–Fe–P alloy is attributed to its electrochemically active constituents, amorphous structure, and the conductive Cu Foil.     

A study on crystal structure,bonding and hydriding properties of Ti–Fe–Ni intermetallics – Behind substitution of iron by nickel

Intermetallic compound TiFe, known for its hydrogen storage applications, is modified by substituting iron by nickel and related changes of properties and applicability of the obtained compounds are studied. Samples TiFe_1−xNi_x (x = 0.2–0.6) are synthesized by melt-spinning and their crystal structure, desorption characteristics and electronic structure are investigated by TPD, ¹H NMR and Mossbauer spectroscopy. State-of-the-art DFT calculations give further insight into the changes in electronic structure and bonding related to the hydrogen absorption and substitution of iron by nickel. The increase of Ni/Fe ratio in the TiFe_1−xNi_x is found to result in the increase of hydride cohesive energies and in the systematic shifting of Fermi energy (E_F) to lower values, in both pure intermetallics and appropriate hydrides. Hydride formation was found to influence the Fermi energy lowering and the increase of number of states at E_F.     

Hydrogen storage properties of Nb–Hf–Ni ternary alloys

The hydrogen storage properties of Nb_xHf_(1−x)/2Ni_(1−x)/2 (x = 15.6, 40) alloys were investigated with respect to their hydrogen absorption/desorption, thermodynamic, and dynamic characteristics. The PCT curves show that all the specimens can absorb hydrogen at 303 K, 373 K, 423 K, 473 K, 523 K, 573 K, and 673 K, but they couldn't desorb hydrogen below 373 K. The maximum hydrogen absorption capacity reaches 1.23 wt.% for Nb_15.6Hf_42.2Ni_42.2 and 1.48 wt.% for Nb₄₀Hf₃₀Ni₃₀ at 303 K at a pressure of 3 MPa. When the temperature was increased, the hydrogen absorption capacities significantly decreased. However, the hydrogen equilibrium pressure increased. When the temperature exceeded 523 K, the hydrogen equilibrium pressure disappeared. When niobium content was increased, the kinetic properties of hydrogen absorption/desorption improved. The results from the microstructure analysis show that both alloys consist of the BCC Nb-based solid solution phase, the B_f-HfNi intermetallic phase, and the eutectic phase {B_f-HfNi + BCC Nb-based solid solution}. When the Nb content was increased, the volume fraction and Nb content in the Nb-based solid solution phase increased. Thus, the improved kinetics is related to the increase in the primary BCC Nb-based solid solution in the Nb₄₀Hf₃₀Ni₃₀ alloy. The kinetic mechanisms of hydrogen absorption/desorption in these two alloys are found to obey the chemical reaction mechanism at all temperatures tested.     

Electrochemical hydrogen storage performance of Mg–Ti–Zr–Ni alloys

Mg_1.5Ti_0.5−xZr_xNi (x = 0, 0.1, 0.2, 0.3, 0.4), Mg_1.5Ti_0.3Zr_0.1Pd_0.1Ni and Mg_1.5Ti_0.3Zr_0.1Co_0.1Ni alloys were synthesized by mechanical alloying and their electrochemical hydrogen storage characteristics were investigated. X-ray diffraction studies showed that all the replacement elements (Ti, Zr, Pd and Co) perfectly dissolved in the amorphous phase and Zr facilitated the amorphization of the alloys. When the Zr/Ti ratio was kept at 1/4 (Mg_1.5Ti_0.4Zr_0.1Ni alloy), the initial discharge capacity of the alloy increased slightly at all the ball milling durations. The further increase in the Zr/Ti ratio resulted in reduction in the initial discharge capacity of the alloys. The presence of Zr in the Ti-including Mg-based alloys improved the cyclic stability of the alloys. This action of Zr was attributed to the less stable and more porous characteristics of the barrier hydroxide layer in the presence of Zr due to the selective dissolution of the disseminated Zr-oxides throughout the hydroxide layer on the alloy surface. Unlike Co, the addition of Pd into the Mg–Ti–Zr–Ni type alloy improved the alloy performance significantly. The positive contribution of Pd was assumed to arise from the facilitated hydrogen diffusion on the electrode surface in the presence of Pd. As the Zr/Ti atomic ratio increased, the charge transfer resistance of the alloy decreased at all the depths of discharges. Co and Pd were observed to increase the charge transfer resistance of the Mg–Ti–Zr–Ni alloys slightly.     

Hydrogenation and electrochemical studies of La–Mg–Ni alloys

La–Mg–Ni alloys are potential candidates for hydrogen storage materials. In this study, mechanical alloying with subsequent annealing under an argon atmosphere at 973 K for 0.5 h, were used to produce La_2-xMg_xNi₇ alloys (x = 0, 0.25, 0.5, 0.75, 1). Shaker type ball mill was used. An objective of the present study was to investigate an influence of amount of Mg in alloy on electrochemical, hydrogenation and dehydrogenation properties of La–Mg–Ni materials. X-ray diffraction analyses revealed formation of material with multi-phase structure. Obtained materials were studied by a conventional Sievert's type device at 303 K. It was observed that electrochemical discharge capacity and gaseous hydrogen storage capacity of La–Mg–Ni alloys increases with Mg content to reach maximum for La_1.5Mg_0.5Ni₇ alloy. Moreover, all of La–Mg–Ni alloys were characterized by improved hydrogen sorption kinetics in comparison to La–Ni alloy.     

Electrodeposition of Ni–Fe–Mn ternary nanosheets as affordable and efficient electrocatalyst for both hydrogen and oxygen evolution reactions

The synthesis of high performance and economical electrocatalysts in the process of overall water splitting is very important for the production of hydrogen energy and has become one of the most important challenges. Here, various Ni, Ni–Fe, Ni–Mn nanosheets and Ni–Fe–Mn ternary nanosheets were created using cost-effective, versatile and binder-free electrochemical deposition methods, and the electrocatalytic activity of various electrodes for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) were investigated in an alkaline environment. Due to the high electrochemical active surface area due to the fabrication of nanosheets, the synergistic effect between different elements on the electronic structure, the high wettability due to the formation of nanosheets and the quick detachment of formed gasses from the electrode, the Ni–Fe–Mn nanosheets electrode showed excellent electrocatalytic activity. In order to deliver the 10 mA cm⁻² current density in HER and OER processes, this electrode required values of 64 mV and 230 mV overpotential, respectively. Also, the stability test showed that after 10 h of electrolysis at a current density of 100 mA cm⁻², the overpotential changes was very small (less than 4%), indicating that the electrode was excellent electrostatic stability. Also, when using as a bi-functional electrode in the full water splitting system, it only needed a cell voltage of 1528 V to deliver a current of 10 mA cm⁻². The results of this study indicate a new strategy for the synthesis of active and stable electrocatalysts.     

Evaluation of Pt–Ru–Ni and Pt–Sn–Ni catalysts as anodes in direct ethanol fuel cells

In this study, the electrooxidation of ethanol on carbon supported Pt–Ru–Ni and Pt–Sn–Ni catalysts is electrochemically studied through cyclic voltammetry at 50 °C in direct ethanol fuel cells. All electrocatalysts are prepared using the ethylene glycol-reduction process and are chemically characterized by energy-dispersive X-ray analysis (EDX). For fuel cell evaluation, electrodes are prepared by the transfer-decal method. Nickel addition to the anode improves DEFC performance. When Pt₇₅Ru₁₅Ni₁₀/C is used as an anode catalyst, the current density obtained in the fuel cell is greater than that of all other investigated catalysts. Tri-metallic catalytic mixtures have a higher performance relative to bi-metallic catalysts. These results are in agreement with CV results that display greater activity for PtRuNi at higher potentials.     

Microstructure and electrochemical properties of Zr–Ti–V–Ni–Mn–LM alloys for application in Ni–MH secondary battery

A series of multi-component Zr_1−xTi_xV_0.4Ni_1.2Mn_0.4LM_y (x=0.3, 0.4; y=0.0,0.02,0.05,0.1,0.2,0.3, LM; lantanum-rich-mischmetal) alloys are prepared and their crystal structure and P–C–T curves are analyzed. The alloys have been modified by adding LM and their gaseous and electrochemical hydrogenation properties are studied to find out the effect of LM elements. Also, the second phase and initial activation performance are investigated. The Zr_1−xTi_xV_0.4Ni_1.2Mn_0.4LM_y (x=0.3,0.4; y=0.0,0.02,0.05,0.1,0.2,0.3) alloys have C14 Laves phase hexagonal structure, so the volume expansion ratio of lattice parameters with LM has increased. As the amount of LM in alloy has increased, correspondingly the second phase is also increased. The second phase is LM, Ti and V-rich. The second phase improve the activation of La-rich misch-metal, and also the concentration of elements Ti, V〉LM〉 matrix in alloys.The addition of LM in Zr_1−xTi_xV_0.4Ni_1.2Mn_0.4LM_y (x=0.3, 0.4) alloys have increased the activation rate and hydrogen storage capacity significantly, but the plateau pressure and the discharge capacity have been decreased due to the formation of second phase. For more Zr in electrode alloys, the activation of rate becomes slow.