System optimization for effective hydrogen production via anaerobic digestion and biogas steam reforming

To construct a system for the effective hydrogen production from food waste, the conditions of anaerobic digestion and biogas reforming have been investigated and optimized. The type of agitator and reactor shape affect the performance of anaerobic digestion reactors. Reactors with a cubical shape and hydrofoil agitator exhibit high performance due to the enhanced axial flow and turbulence as confirmed by simulation of computational fluid dynamics. The stability of an optimized anaerobic digestion reactor has been tested for 60 days. As a result, 84 L of biogas is produced from 1 kg of food waste. Reaction conditions, such as reaction temperature and steam/methane ratio, affect the biogas steam reforming reaction. The reactant conversions, product yields, and hydrogen production are influenced by reaction conditions. The optimized reaction conditions include a reaction temperature of 700 °C and H₂O/CH₄ ratio of 1.0. Under these conditions, hydrogen can be produced via steam reforming of biogas generated from a two-stage anaerobic digestion reactor for 25 h without significant deactivation and fluctuation.     

Biomass gasification coupled with producer gas cleaning,bottling and HTS catalyst treatment for H2-rich gas production

The aim of the present study is to demonstrate the production of hydrogen-rich fuel gas from J. curcas residue cake. A comprehensive experimental study for the production of hydrogen rich fuel gas from J. curcas residue cake via downdraft gasification followed by high temperature water gas shift catalytic treatment has been carried out. The gasification experiments are performed at different equivalence ratios and performance of the process is reported in terms of producer gas composition & its calorific value, gas production rate and cold gas efficiency. The producer gas is cleaned of tar and particulate matters by passing it through venturi scrubber followed by sand bed filter. The clean producer gas is then compressed at 0.6 MPa and bottled into a gas cylinder. The bottled producer gas and a simulated mixture of producer gas are then subjected to high temperature shift (HTS) catalytic treatment for hydrogen enriched gas production. The effect of three different operating parameters GHSV, steam to CO ratio and reactor temperature on the product gas composition and CO conversion is reported. From the experimental study it is found that, the presence of oxygen in the bottled producer gas has affected the catalyst activity. Moreover, higher concentration of oxygen concentration in the bottled producer gas leads to the instantaneous deactivation of the HTS catalyst.     

Production of hydrogen enriched syngas from municipal solid waste gasification with waste marble powder as a catalyst

Marble processing leads to the production of high amount of waste marble powder (WMP) as a byproduct, which can be a potential health risk and has hazardous impacts on the surrounding environment. However, marble is composed of calcite making it suitable for the calcium-based catalyst. Moreover, no study has been carried out to utilize this WMP in municipal solid waste (MSW) gasification process. Therefore, there is a need to address its utilization as a potential catalyst/sorbent in the gasification of municipal solid waste (MSW). A laboratory scale batch-type fixed bed reactor was used to study the effect of WMP addition on the CO₂ adsorption, steam reforming capability and char gasification in the presence of steam. Produced gas composition, gas yield, carbon conversion efficiency and tar yield were examined at different WMP to MSW ratios. Effect of temperature and steam rate varying from 700 to 900 °C and 2.5–10 ml/min respectively were also considered in this study. WMP showed a good capacity towards hydrogen enriched syngas production as well as CO₂ adsorption and tar reforming. The H₂ concentration increased significantly with an increase in the WMP to MSW mass ratio, while CO₂ decreased. A significant effect of temperature and steam rate was also observed on the produced gas composition, gas yield, and tar content. This study helps us to understand the effect of WMP addition in MSW gasification process and thus assists in the industrial application.     

A strategy of mid-temperature natural gas based chemical looping reforming for hydrogen production

Steam methane reforming (SMR) needs the reaction heat at a temperature above 800 °C provided by the combustion of natural gas and suffers from adverse environmental impact and the hydrogen separated from other chemicals needs extra energy penalty. In order to avoid the expensive cost and high power consumption caused by capturing CO₂ after combustion in SMR, natural gas Chemical Looping Reforming (CLR) is proposed, where the chemical looping combustion of metal oxides replaced the direct combustion of NG to convert natural gas to hydrogen and carbon dioxide. Although CO₂ can be separated with less energy penalty when combustion, CLR still require higher temperature heat for the hydrogen production and cause the poor sintering of oxygen carriers (OC). Here, we report a high-rate hydrogen production and low-energy penalty of strategy by natural gas chemical-looping process with both metallic oxide reduction and metal oxidation coupled with steam. Fe₃O₄ is employed as an oxygen carrier. Different from the common chemical looping reforming, the double side reactions of both the reduction and oxidization enable to provide the hydrogen in the range of 500–600 °C under the atmospheric pressure. Furthermore, the CO₂ is absorbed and captured with reduction reaction simultaneously.Through the thermodynamic analysis and irreversibility analysis of hydrogen production by natural gas via chemical looping reforming at atmospheric pressure, we provide a possibility of hydrogen production from methane at moderate temperature. The reported results in this paper should be viewed as optimistic due to several idealized assumptions: Considering that the chemical looping reaction is carried out at the equilibrium temperature of 500 °C, and complete CO₂ capture can be achieved. It is assumed that the unreacted methane and hydrogen are completely separated by physical adsorption. This paper may have the potential of saving the natural gas consumption required to produce 1 m³ H₂ and reducing the cost of hydrogen production.     

Steam reforming of acetic acid for hydrogenproduction: Catalytic performances of Ni and Co supported on Ce0·75Zr0·25O2 catalysts

The catalytic steam reforming of acetic acid over both Ni/ and Co/Ce_0·75Zr_0·25O₂ (CZO) catalysts in the temperature range of 450–650 °C and steam-to-carbon molar ratios of 3–9 was studied. It was found that the complete acetic acid conversion was achieved for all the conditions investigated. Nevertheless, the C–C bond cleavage conversion was attained less than the acetic acid conversion at a given condition due to carbon deposition on the catalyst. However, hydrogen yield was obtained in the same trend as C–C bond cleavage conversion as well. The results revealed that the CZO as an active support prefers to promote the ketonization reaction to the C-C bond cleavage reaction at a lower temperature, and vice versa at a higher temperature. The Ni/CZO catalyst exhibits higher C–C bond cleavage conversion than the Co/CZO catalyst particularly at 650 °C whereas the Co/CZO catalyst is more active for ketonization reaction at low temperatures. However, as an increase in reaction temperature, the Co/CZO catalyst promotes ketonization reaction more pronouncedly toward aldol-condensation reaction thus giving rise to the carbon deposition. The results deduced from the effect of space velocity on the activity and product distribution suggested that the steam reforming of acetic acid over Ni/CZO catalyst is dominated by decomposition of acetic acid, while that of Co/CZO catalyst by ketonization reaction.     

Characteristics and performance of the Co–CeO2 catalyst as a function of the promoter (La,Pr, and Zr) used in high temperature water gas shift reaction

The catalysts used to facilitate the water gas shift reaction (WGSR) are generally harmful to the environment. Therefore, catalysts that have high activity and stability in WGSR and do not pollute the environment need to be fabricated. Herein, three promoters (La, Pr, and Zr) are added into Co–CeO₂ (CoCe) catalyst to improve catalytic performance in a high temperature WGSR to produce high-purity hydrogen from waste-derived synthesis gas. Various techniques are employed to confirm the changes in the properties that affect the catalytic performance. The catalytic reaction is performed at a high gas hourly space velocity to screen the performance of the promoted CoCe catalysts. The CoCeZr catalyst shows the highest CO conversion (X_CO = 88% at 450 °C) due to its high Co dispersion and oxygen vacancy resulting from the addition of Zr to the CoCe catalyst; thus, it is most suitable for use in high temperature WGSR.     

Transient numerical modeling and model predictive control of an industrial-scale steam methane reforming reactor

A steam methane reforming reactor is a key equipment in hydrogen production, and numerical analysis and process control can provide a critical insight into its reforming mechanisms and flexible operation in real engineering applications. The present paper firstly studies the transport phenomena in an industrial-scale steam methane reforming reactor by transient numerical simulations. Wall effect and local non thermal equilibrium is considered in the simulations. A temperature profile of the tube outer wall is given by user defined functions integrated into the ANSYS FLUENT software. Dynamic simulations show that the species distribution is closely related to the temperature distribution which makes the temperature of the reactor tube wall an important factor for the hydrogen production of the reformer and the thermal conductivity of the catalyst network is crucial in the heat transfer in the reactor. Besides, there exists a delay of the reformer's hydrogen production when the temperature profile of the tube wall changes. Among inlet temperature, inlet mass flow rate and inlet steam-to-carbon (S/C) ratio, the mass flow rate is the most influencing factor for the hydrogen production. The dynamic matrix control (DMC) scheme is subsequently designed to manipulate the mole fraction of hydrogen of the outlet to the target value by setting the temperature profile trajectory of the reforming tube with time. The proportional-integral control strategy is also studied for comparison. The closed-loop simulation results show that the proposed DMC control strategy can reduce the overshoot and have a small change of the input variable. In addition, the disturbances of feed disturbance can also be well rejected to assure the tracking performance, indicating the superiority of the DMC controller. All the results give insight to the theoretical analysis and controller design of a steam methane reformer and demonstrate the potential of the CFD modeling in study the transport mechanism and the idea of combining CFD modeling with controller design for the real application.     

Steam reforming of 1-methylnaphthalene over pure CeO2 under model coke oven gas conditions containing high H2S concentrations

Tar and H₂S are obstacles to the efficient production of H₂ from unused industrial gases and biomass gasification gases. Robust catalysts against tar and H₂S are required to produce H₂ from such resources. Herein, a stable steam reforming reaction is demonstrated over pure CeO₂ under reaction conditions consisting of ~2 vol% 1-methylnaphthalene and ~1000 ppm H₂S. The presence of H₂S significantly suppressed Ni/MgO/Al₂O₃ activity and increased carbon deposition, regardless of the steam to carbon (S/C) ratio. In contrast, the promotion or suppression of CeO₂ activity in the presence of H₂S was dependent on the S/C ratio. At S/C = 1.2, H₂S deactivated the CeO₂ catalyst and increased carbon deposition. Conversely, H₂S promoted the reforming reaction and decreased carbon deposition on CeO₂ at S/C ≥ 2.0. The results of this study clarify that pure CeO₂ exhibits outstanding and stable activity for the steam reforming reaction of 1-methylnaphthalene in the presence of H₂S by controlling the S/C of the inlet gas.     

Hydrofluoroolefin-based mixed refrigerant for enhanced performance of hydrogen liquefaction process

Hydrogen has the highest gravimetric energy density of all fuels; however, it has a low volumetric energy density, unfavorable for storage and transportation. Hydrogen is usually liquefied to meet the bulk transportation needs. The exothermic interconversion of its spin isomers is an additional activity to an already energy-intensive process. The most significant temperature drop occurs in the precooling cycle (between ?150 °C and up to ?180 °C) and consumes more than 50% of the required energy. To reduce the energy consumption and improve the exergy efficiency of the hydrogen liquefaction process, a new high-boiling component, Hydrofluoroolefin (HFO-1234yf), is added to the precooled mixed refrigerant. As a result, the specific energy consumption of precooling cycle reduces by 41.8%, from 10.15 kWh/kg_LH2 to 5.90 kWh/kg_LH2, for the overall process. The exergy efficiency of the proposed case increases by 43.7%; however, the total equipment cost is also the highest. The inflated cost is primarily due to the added ortho-to-para hydrogen conversion reactor, boosting the para-hydrogen concentration. From the perspective of bulk storage and transportation of liquid hydrogen, the simplicity of design and low energy consumption build a convincing case for considering the commercialization of the process.     

Turning glycerol surplus into renewable syngas through glycerol steam reforming over a sol-gel Ni–Mo2C-Al2O3 catalyst

In this work, a sol-gel Ni–Mo₂C–Al₂O₃ catalyst is employed for the first time in the glycerol steam reforming for syngas production. Catalyst stability and activity are investigated in the temperature range of 550 °C–700 °C and time on stream up to 30 h. As reaction temperature increases, from 550 °C to 700 °C, H₂ yield boosts from 22% to 60%. The stability test, carried out at milder conditions (600 °C and Gas-Hourly Space-Velocity (GHSV) of 50,000 mL h⁻¹.g_cat⁻¹), shows high catalyst stability, up to 30 h, with final conversion, H₂ yield, and H₂/CO ratio of 95%, 53% and 1.95, respectively. Both virgin and spent catalysts have been characterized by a multitude of techniques, e.g., Atomic-Absorption spectroscopy, Raman spectroscopy, N₂-adsorption-desorption, and Transmission Electron Microscopy (TEM), among others. Regarding the spent catalysts, carbon deposits’ morphology becomes more graphitic as the reaction temperature increases, and the total coke formation is mitigated by increasing reaction temperature and lowering GHSV.     

Hydrogen-rich syngas production by gasification of Urea-formaldehyde plastics in supercritical water

Supercritical water is a promising medium to convert plastics into hydrogen and other recyclable products efficiently. In previous research, supercritical water gasification characteristics investigations focus on thermoplastics instead of thermoset plastics due to its chemical, thermal and mechanical stability. Urea-formaldehyde (UF) plastics were selected as a typical kind of thermoset plastics for investigation in this paper and quartz tubes were used as the reactor in order to avoid the potential catalytic effect of metal reactor wall. Conversion characteristic were studied and the influence of different operating parameters such as temperature, reaction time, feedstock mass fraction and pressure were investigated respectively. The molar fraction of hydrogen could reach about 70% in 700 °C. Products in gas phase and solid phase were analyzed, and properties, chemical structures and inhibition mechanism of thermoset plastics was analyzed after comparing with polystyrene (PS) plastics. The result showed that increase of high temperature and long reaction time could promote gasification process, meanwhile the increase in the feedstock mass fraction would result in suppression of the gasification process. Finally, kinetic study of UF was carried out and the activation energy and pre-exponential factor of the Arrhenius equation were calculated as 30.09 ± 1.62 kJ/mol and 0.1199 ± 0.0049 min⁻¹, respectively.     

Supercritical water gasification mechanism of polymer-containing oily sludge

In the offshore petroleum industry, polymer-containing oily sludge (PCOS) hinders oil extraction and causes tremendous hazards to the marine ecological environment. In this paper, an effective pretreatment method is proposed to break the adhesive structure of PCOS, and the experiments of supercritical water gasification are carried out under the influencing factors including residence time (5–30 min) and temperature (400–750 °C) in batch reactors. The increase of time and temperature all show great promoting effects on gas production. Polycyclic aromatic hydrocarbons, including naphthalene and phenanthrene, are considered as the main obstacles for a complete gasification. Carbon gasification efficiency (CE) reaches maximum of 95.82% at 750 °C, 23 MPa for 30 min, while naphthalene makes up 70% of the organic compounds in residual liquid products. The highest hydrogen yield of 19.79 (mol H₂/kg of PCOS) is observed in 750 °C for 25 min. A simplified reaction pathway is presented to describe the gaseous products (H₂, CO, CO₂, CH₄). Two intermediates are defined for describing the reaction process bases on the exhaustive study on organic matters in residual liquid products. The results show that the calculated data and the experimental data have a high degree of fit and tar formation reaction is finished within 10 min.     

HRT control as a strategy to enhance continuous hydrogen production from sugarcane juice under mesophilic and thermophilic conditions in AFBRs

The objective of this study was to evaluate the effects of hydraulic retention time (HRT) (8–1 h) on H₂ production from sugarcane juice (5000 mg COD L⁻¹) in mesophilic (30 °C, AFBR-30) and thermophilic (55 °C, AFBR-55) anaerobic fluidized bed reactors (AFBRs). At HRTs of 8 and 1 h in AFBR-30, the H₂ production rates were 60 and 116 mL H₂ h⁻¹ L⁻¹, the hydrogen yields were 0.60 and 0.10 mol H₂ mol⁻¹ hexose, and the highest bacterial diversities were 2.47 and 2.34, respectively. In AFBR-55, the decrease in the HRT from 8 to 1 h increased the hydrogen production rate to 501 mL H₂ h⁻¹ L⁻¹ at the HRT of 1 h. The maximum hydrogen yield of 1.52 mol H₂ mol⁻¹ hexose was observed at the HRT of 2 h and was associated with the lowest bacterial diversity (0.92) and highest bacterial dominance (0.52).     

Demonstration of a single-stage metal hydride hydrogen compressor composed of BCC V40TiCr alloy

In this study, demonstration of a one-stage metal hydride hydrogen compressor (MH compressor) by using a BCC alloy was performed. It was estimated that V₄₀Ti₂₂Cr₃₈ could compress approximately 1.6 wt% of hydrogen from 1.0 to 10 MPa in 20–140 °C temperature range from equilibrium theory via pressure-composition-isotherm measurements. For demonstration of an actual MH compressor, a kg-scale experimental system was set up; V₄₀Ti₂₂Cr₃₈ (1.4 kg) was introduced into a 1-inch cylindrical vessel with a heat-medium flow tube outside. As a result, 1.0 MPa of hydrogen can be compressed into the hydrogen cylinder at >10 MPa by hydrogen absorption at 10 °C and desorption at 160 °C for 30 min each (1 cycle/h) to achieve a compression rate of 0.23 Nm³/h and indicate the potential of the practical MH compressors by using BCC alloy.     

Valorisation of lignocellulosic biomass investigating different pyrolysis temperatures

Presently, sugarcane bagasse (SB) and oat hulls (OH) have a distinctive potential as a renewable source of biomass, due to its global availability, which is advantageous for producing liquid and gaseous fuels by thermochemical processes. Thermo-Catalytic Reforming (TCR) is a pyrolysis based technology for generating energy vectors (char, bio-oil and syngas) from biomass wastes. This work aims to study the conversion of SB and OH into fuels, using TCR in a 2 kg/h continuous pilot-scale reactor at different pyrolysis temperatures. The pyrolysis temperatures were studied at 400, 450 and 500 °C, while the subsequent reforming temperature remained constant at 500 °C. The bio-oil contained the highest calorific value of 33.4 and 33.5 MJ/kg for SB and OH, respectively at 500 °C pyrolysis temperature, which represented a notable increase compared to the raw material calorific value of SB and OH (16.4 and 16.0 MJ/kg, respectively), this was the result of deoxygenation reactions occurring. Furthermore, the increment of the pyrolysis temperature improved the water content, total acid number (TAN), viscosity and density of the bio-oil. The syngas and the biochar properties did not change significantly with the increase of the pyrolysis temperature. In order to use TCR bio-oil as an engine fuel, it is necessary to carry out some upgrading treatments; or blend it with fossil fuels if it is to be used as a transportation fuel. Overall, TCR is a promising future route for the valorisation of lignocellulosic residues to produce energy vectors.     

Catalyst modification strategies to enhance the catalyst activity and stability during steam reforming of acetic acid for hydrogen production

A high energy content (∼122 MJ/kg H₂) and presence of hydrogen-bearing compounds abundance in nature make hydrogen forth runner candidate to fulfill future energy requirements. Biomass being abundant and carbon neutral is one of the promising source of hydrogen production. In addition, it also addresses agricultural waste disposal problems and will bring down our dependency on fossil fuel for energy requirements. Biomass-derived bio-oil can be an efficient way for hydrogen production. Acetic acid is the major component of bio-oil and has been extensively studied by the researchers round the globe as a test component of bio-oil for hydrogen generation. Hydrogen can be generated from acetic acid via catalytic steam reforming process which is thermodynamically feasible. A number of nickel-based catalysts have been reported. However, the coke deposition during reforming remains a major challenge. In this review, we have investigated all possible reactions during acetic acid steam reforming (AASR), which can cause coke deposition over the catalyst surface. Different operating parameters such as temperature and steam to carbon feed ratio affect not only the product distribution but also the carbon formation during the reaction. Present review elaborates effects of preparation methods, active metal catalyst including bimetallic catalysts, type of support and microstructure of catalysts on coke resistance behavior and catalyst stability during reforming reactions. The present study also focuses on the effects of a combination of a variety of alkali and alkaline earth metals (AAEM) promoters on coke deposition. Effect of specially designed reactors and the addition of oxygen on carbon deposition during AASR have also been analyzed. This review based on the available literature focuses mainly on the catalyst deactivation because of coke deposition, and possible strategies to minimize catalyst deactivation during AASR.     

Effect of manifold injection of hydrogen gas in producer gas and neem biodiesel fueled CRDI dual fuel engine

The high flammability of hydrogen gas gives it a steady flow without throttling in engines while operating. Such engines also include different induction/injection methods. Hydrogen fuels are encouraging fuel for applications of diesel engines in dual fuel mode operation. Engines operating with dual fuel can replace pilot injection of liquid fuel with gaseous fuels, significantly being eco-friendly. Lower particulate matter (PM) and nitrogen oxides (NO_x) emissions are the significant advantages of operating with dual fuel.Consequently, fuels used in the present work are renewable and can generate power for different applications. Hydrogen being gaseous fuel acts as an alternative and shows fascinating use along with diesel to operate the engines with lower emissions. Such engines can also be operated either by injection or induction on compression of gaseous fuels for combustion by initiating with the pilot amount of biodiesel. Present work highlights the experimental investigation conducted on dual fuel mode operation of diesel engine using Neem Oil Methyl Ester (NeOME) and producer gas with enriched hydrogen gas combination. Experiments were performed at four different manifold hydrogen gas injection timings of TDC, 5°aTDC, 10°aTDC and 15°aTDC and three injection durations of 30°CA, 60°CA, and 90°CA. Compared to baseline operation, improvement in engine performance was evaluated in combustion and its emission characteristics. Current experimental investigations revealed that the 10°aTDC hydrogen manifold injection with 60°CA injection duration showed better performance. The BTE of diesel + PG and NeOME + PG operation was found to be 28% and 23%, respectively, and the emissions level were reduced to 25.4%, 14.6%, 54.6%, and 26.8% for CO, HC, smoke, and NO_x, respectively.     

Molten salt synthesis of high-entropy alloy AlCoCrFeNiV nanoparticles for the catalytic hydrogenation of p-nitrophenol by NaBH4

High-entropy alloy (HEA) AlCoCrFeNiV nanoparticles were prepared from oxide precursors using a molten salt synthesis method without an electrical supply. The oxide precursor was directly reduced by CaH₂ reducing agent in molten LiCl at 600°C-700°C or molten LiCl–CaCl₂ at 500°C-550°C. When the reduction was conducted at 700°C, a face-centered cubic (FCC) structure produced, as identified by X-ray diffraction analysis. With lower reduction temperatures, the FCC structure was absent, replaced by a body-centered cubic (BCC) structure. With a reduction temperature of 550°C, the resulting sample was composed of highly pure HEA AlCoCrFeNiV nanoparticles with a BCC structure of 15 nm. Analyses by scanning electron microscopy/transmission electron microscopy with energy-dispersive X-ray spectroscopy confirmed the formation of homogeneous HEA AlCoCrFeNiV with a nanoscale morphology. In the hydrogenation reaction of p-nitrophenol by NaBH₄, the AlCoCrFeNiV nanoparticles (produced at 550°C) exhibited a catalytic activity with ～90% conversion and 16 kJ/mol activation energy.     

Nickel-loaded red mud catalyst for steam gasification of bamboo sawdust to produce hydrogen-rich syngas

Ni/red mud (RM) catalysts were prepared by wet impregnation and used in the catalytic steam gasification of bamboo sawdust (BS) to produce hydrogen-rich syngas. The system was optimized in terms of the amount of added nickel (10%), reaction temperature (800 °C), and catalyst placement (separately behind the BS). The maximum H₂ yield was 17.3% higher than that using pure RM catalyst and 43.8% higher than that of BS gasification alone, and the H₂/CO ratio in the syngas reached 7.82. This Ni/RM catalyst also retained good activity after six cycles in a double-stage fixed bed reactor. Analysis using X-ray fluorescence, X-ray diffraction, scanning electron microscopy-energy dispersive spectroscopy, and other methods revealed that the interaction of Ni, Fe, and Mg in Ni/RM produced bimetallic compounds containing active sites, such as NiFe₂O₄, MgNiO₂, and NiO. This explains the good catalytic performance in the tar conversion during the gasification process.     

Production of syngas from steam gasification of three different ranks of coals and related reaction kinetics

The steam gasification properties of three different ranks of coals, Shengli lignite (SL), Shenhua subbituminous coal (SH), and Tavan Tolgoi anthracite (TT), were investigated using a lab-scale fixed-bed reactor, and the thermodynamic equilibrium constant and kinetics of the reaction were analyzed. The results showed that the aromaticity and condensation of aromatic structures in SL, SH, and TT became higher, and the maturity of organic substance became lower. The steam gasification reaction showed that the syngas from low-rank SL had a high H₂/CO molar ratio, while the syngas from high-rank TT had relatively high CO content. The direct carbon gasification reactions for these three different ranks of coals were far from in equilibrium; the water gas shift reaction of SL was near equilibrium, and the degree of reaction for SL was higher than that of SH and TT. We studied a random pore model (RPM), shrinking core model (SCM), and hybrid model (HM), and the hybrid model was found to be the most suitable model of the three for fitting the steam gasification reactions of the three types of coal. It had high fitting correlation coefficient R² values (ranging from 0.9939 to 0.9990) and small average error θ values (ranging from 0.009 to 0.016). The apparent activation energy E values of SL, SH, and TT fitted by HM were 179.10, 48.14, and 63.06 kJ/mol, respectively, and the corresponding pre-exponential factor k₀ values were 3.14 × 10⁷, 1.01, and 1.22 min⁻¹, respectively. This study finds that the steam gasification of SL, SH, and TT coal samples consists of homogeneous phase reaction and shrinking core reaction.