Effect of manifold injection of hydrogen gas in producer gas and neem biodiesel fueled CRDI dual fuel engine

The high flammability of hydrogen gas gives it a steady flow without throttling in engines while operating. Such engines also include different induction/injection methods. Hydrogen fuels are encouraging fuel for applications of diesel engines in dual fuel mode operation. Engines operating with dual fuel can replace pilot injection of liquid fuel with gaseous fuels, significantly being eco-friendly. Lower particulate matter (PM) and nitrogen oxides (NO_x) emissions are the significant advantages of operating with dual fuel.Consequently, fuels used in the present work are renewable and can generate power for different applications. Hydrogen being gaseous fuel acts as an alternative and shows fascinating use along with diesel to operate the engines with lower emissions. Such engines can also be operated either by injection or induction on compression of gaseous fuels for combustion by initiating with the pilot amount of biodiesel. Present work highlights the experimental investigation conducted on dual fuel mode operation of diesel engine using Neem Oil Methyl Ester (NeOME) and producer gas with enriched hydrogen gas combination. Experiments were performed at four different manifold hydrogen gas injection timings of TDC, 5°aTDC, 10°aTDC and 15°aTDC and three injection durations of 30°CA, 60°CA, and 90°CA. Compared to baseline operation, improvement in engine performance was evaluated in combustion and its emission characteristics. Current experimental investigations revealed that the 10°aTDC hydrogen manifold injection with 60°CA injection duration showed better performance. The BTE of diesel + PG and NeOME + PG operation was found to be 28% and 23%, respectively, and the emissions level were reduced to 25.4%, 14.6%, 54.6%, and 26.8% for CO, HC, smoke, and NO_x, respectively.     

Reinforcement learning based energy management systems and hydrogen refuelling stations for fuel cell electric vehicles: An overview

This paper examines the current state of the art of hydrogen refuelling stations-based production and storage systems for fuel cell hybrid electric vehicles (FCHEV). Nowadays, the emissions are increasing rapidly due to the usage of fossil fuels and the demand for hydrogen refuelling stations (HRS) is emerging to replace the conventional vehicles with FCHEVs. Hence, the availability of HRS and its economic aspects are discussed. In addition, a comprehensive study is presented on the energy storage systems such as batteries, supercapacitors and fuel cells which play a major role in the FCHEVs. An energy management system (EMS) is essential to meet the load requirement with effective utilisation of power sources with various optimizing techniques. A detailed comparative analysis is presented on the merits of Reinforcement learning (RL) for the FCHEVs. The significant challenges are discussed in depth with potential solutions for future work.     

A techno-economic study for a hydrogen storage system in a microgrid located in baja California,Mexico. Levelized cost of energy for power to gas to power scenarios

In this work a techno economic feasibility study is carried out to implement a Hydrogen based Power to Gas to Power (P2G2P) in a Microgrid, located in a rural area in Baja California, Mexico. The study aims to define the feasibility to store energy throughout seasons with this novel alternative using an electrolyzer to produce green hydrogen from excess renewable energy in winter, to store it during months and re inject it to the grid as electricity by a fuel cell in the high energy demanding season. The Microgrid was modeled in Homer software and simulations of the P2G2P lead to Levelized Cost of Energy data to compare between the P2G2P scenarios and the current diesel-battery based solution to complete the high demand by the community. This study shows that using hydrogen and fuel cells to substitute diesel generators it is possible to reduce CO₂ emissions up to a 27% and that in order for the P2G2P to be cost competitive, the fuel cell should reduce its cost in 50%; confirming that, in the medium to long term, the hydrogen storage system is a coherent alternative towards decarbonization of the distributed energy generation.     

Clean hydrogen for mobility – Quo vadis?

Achieving complete combustion of fossil fuels has long been thought of as a sufficient remedy for tackling vehicular emissions and the ensuing environmental effects. However, thanks to the increasing awareness around the climate change, the global dialogue has now shifted to realizing a carbon-free economy, which has set stricter curbs on the energy source that can power the future mobility. Therefore, the idea of “clean combustion” requires rethinking. Of the many choices for alternative clean fuels that are both energy-efficient and environment-friendly, hydrogen has always been eyed as the best clean alternative there is. This article reviews various available approaches to utilizing hydrogen for mobility applications with a discussion of their relative merits and shortcomings. In addition to well-discussed methods like fuel cell electric vehicles, hydrogen-based IC engines, and dual-fuel operation with hydrogen, this review also assesses the technical and economic feasibilities of using hydrogen in e-fuels and their implications for our existing infrastructure and future energy demands.     

Hydrogen fuel cell heavy-duty trucks: Review of main research topics

Road transportation is a significant source of CO₂ emissions and energy demand. Consequently, initiatives are being promoted to decrease the sector's emissions and comply with the Paris agreement. This article synthesizes the available information about heavy-duty fuel cell trucks as their deployment needs to be considered a complementary solution to decreasing CO₂ emissions alongside battery electric vehicles. A thorough evaluation of 95 relevant documents determines that the main research topics in the past ten years converge on public policies, hydrogen supply chain, environmental impact, drivetrain technology, fuel cell, and storage tank applications. The identified research gaps relate to expanding collaboration between institutions and governments in developing joint green macro policies focused on hydrogen heavy-duty trucks, scarce research about hydrogen production energy sources, low interest in documenting hydrogen pilot projects, and minimal involvement of logistic companies, which need to plan their diesel freight's conversion as soon as possible.     

Review of hydrogen economy in Malaysia and its way forward

Heavy fossil fuels consumption has raised concerns over the energy security and climate change while hydrogen is regarded as the fuel of future to decarbonize global energy use. Hydrogen is commonly used as feedstocks in chemical industries and has a wide range of energy applications such as vehicle fuel, boiler fuel, and energy storage. However, the development of hydrogen energy in Malaysia is sluggish despite the predefined targets in hydrogen roadmap. This paper aims to study the future directions of hydrogen economy in Malaysia considering a variety of hydrogen applications. The potential approaches for hydrogen production, storage, distribution and application in Malaysia have been reviewed and the challenges of hydrogen economy are discussed. A conceptual framework for the accomplishment of hydrogen economy has been proposed where renewable hydrogen could penetrate Malaysia market in three phases. In the first phase, the market should aim to utilize the hydrogen as feedstock for chemical industries. Once the hydrogen production side is matured in the second phase, hydrogen should be used as fuel in internal combustion engines or burners. In the final phase hydrogen should be used as fuel for automobiles (using fuel cell), fuel-cell combined heat and power (CHP) and as energy storage.     

Economic valuation of green hydrogen charging compared to gray hydrogen charging: The case of South Korea

The South Korean government promotes hydrogen-powered vehicles to reduce greenhouse gas (GHG) emissions but these vehicles use gray hydrogen while charging, which causes GHG emissions. Therefore, converting this fuel into green hydrogen is necessary to help reduce GHG emissions, which will incur investment costs of approximately USD 20 billion over a decade. In this study, a contingent valuation method is applied in an analysis to examine the extent to which consumers are willing to pay for green hydrogen charging compared to gray hydrogen charging. The results indicate that the monthly mean of willingness to pay per driver is 51,674 KRW (USD 45.85), equivalent to 4302 KRW per kg (USD 3.82). Additionally, consumers accept a 28.5% increase in the monthly average fuel expenses when converting to green hydrogen. These findings can be used in the development of pricing and energy use plans to finance the expansion of green hydrogen infrastructure.     

DIR-FCEV powered by different fuels – Part I: Well-to-wheel analysis for the Brazilian and Spanish contexts

This article describes the life cycle assessment of the Direct Internal Reforming Fuel Cell Electric Vehicle (DIR-FCEV) for the Brazilian and Spanish contexts. This recently proposed vehicle technology produces hydrogen onboard via heat recovery, while the Solid Oxide Fuel Cell (SOFC) and the gas turbine provide electricity to the electric motor with high overall efficiency. The exhaust gas emission was obtained via GASEQ software and the well-to-tank data were collected through literature search. These values were entered in the GREET Model software version v1.3.0.13656 to assess the negative environmental impacts of the DIR-FCEV in terms of global warming potential (GWP) and human toxicity potential (HTP). Using 1 km distance driven by a light-duty vehicle as the functional unit, the tank-to-wheel results indicate that regardless of the fuel, the DIR-FCEV achieved better than the internal combustion engine vehicle fuelled with gasoline A in both categories. Also, the DIR-FCEV powered by biomethane, gasoline A, gasoline C (73% gasoline A and 27% ethanol, in volume basis), glycerine, and ethanol attended all future tailpipe emissions standards stipulated by United States and European Union. Biomethane and gasoline-fuelled DIR-FCEV had more commendatory environmental performance in both countries. Thus, it is expected to obtain environmental indicators to stimulate the use of biofuels synergistically with the advancement of electromobility in Brazil and Spain.     

Effect of high compression ratio on improving thermal efficiency and NOx formation in jet plume controlled direct-injection near-zero emission hydrogen engines

The Plume Ignition and Combustion Concept (PCC) developed by the authors significantly reduced nitrogen oxide (NOx) emissions in a direct-injection hydrogen engine under high-load operation. With PCC, a rich fuel plume is ignited immediately after completion of injection in the latter half of the compression stroke to reduce NOx formation. Simultaneously, high thermal efficiency was also achieved by mitigating cooling losses through optimization of the jet configuration in the combustion chamber. This basic combustion concept was applied to burn lean mixture in combination with the optimized hydrogen jet configuration and the application of supercharging to recover the power output decline due to the use of a diluted mixture. As a result, a near-zero-emission-level engine has been achieved that simultaneously provides high thermal efficiency, high power output and low NOx emissions at a single-digit ppm level [1]. In this study, a high compression ratio was applied to improve thermal efficiency further by taking advantage of the characteristics of hydrogen fuel, especially its diluted mixture with a high anti-knock property. As a result, NOx emissions at a single-digit ppm level and gross indicated thermal efficiency of 52.5% were achieved while suppressing knocking at a compression ratio of 20:1 by optimizing the excess air ratio and injection timing, and increasing power output by supercharging.     

Effects of hydrogen enrichment of methane on diffusion flame structure and emissions in a back-pressure combustion chamber

In the present study, the effects of hydrogen enrichment of methane are investigated numerically from the diffusion flame structure and emissions aspect. Fluent code is utilised as the simulation tool. In the first part of the study, four experiments were conducted using natural gas as fuel. A non-premixed burner and a back-pressure boiler were utilised as the experimental setup. The natural gas fuel consumption rate was changed between 22 Nm³/h and 51 Nm³/h. After the experimental studies, the numerical simulations were performed. The non-premixed combustion model with the steady laminar flamelet model (SFM) approach was used for the calculations. The methane-air extinction mechanism was utilised for the calculation of the chemical species. The numerical results were verified with the experimental results in terms of the flue gas emissions and flue gas temperature values. In the second part of the study, four different hydrogen-enriched methane combustion cases were simulated using the same methane-air extinction mechanism, which included the hydrogen oxidation mechanism as a sub mechanism. The same energy input (432 kW) was supplied into the boiler for all the studied cases. The obtained results show that the hydrogen addition to methane significantly change the diffusion flame structure in the combustion chamber. The hydrogen-enriched flames become broader and shorter with respect to the pure methane flame. This provides better mixing of the reactants and combustion products in the flame regions due to the use of a back-pressure boiler. In this way, the maximum flame temperature values and thermal NO emissions are reduced in the combustion chamber, when the hydrogen addition ratio is less than 15% by mass. The maximum temperature value is calculated as 2030 K for the case with 15% hydrogen addition ratio by mass, while it is 2050 K for the case without hydrogen enrichment. Therefore, it is determined that the hydrogen-enriched methane combustion in a back-pressure combustion chamber has the potential of reducing both the carbon and thermal NO emissions.     

Expected impacts on greenhouse gas and air pollutant emissions due to a possible transition towards a hydrogen economy in German road transport

Transitioning German road transport partially to hydrogen energy is among the possibilities being discussed to help meet national climate targets. This study investigates impacts of a hypothetical, complete transition from conventionally-fueled to hydrogen-powered German transport through representative scenarios. Our results show that German emissions change between ?179 and +95 MtCO₂eq annually, depending on the scenario, with renewable-powered electrolysis leading to the greatest emissions reduction, while electrolysis using the fossil-intense current electricity mix leads to the greatest increase. German energy emissions of regulated pollutants decrease significantly, indicating the potential for simultaneous air quality improvements. Vehicular hydrogen demand is 1000 PJ annually, requiring 446–525 TWh for electrolysis, hydrogen transport and storage, which could be supplied by future German renewable generation, supporting the potential for CO₂-free hydrogen traffic and increased energy security. Thus hydrogen-powered transport could contribute significantly to climate and air quality goals, warranting further research and political discussion about this possibility.     

Improving inter-plant integration of syngas production technologies by the recycling of CO2 and by-product of the Fischer-Tropsch process

This paper deals with the emission reduction in synthesis-gas production by better integration and increasing the energy efficiency of a high-temperature co-electrolysis unit combined with the Fischer-Tropsch process. The investigated process utilises the by-product of Fischer-Tropsch, as an energy source and carbon dioxide as a feedstock for synthesis gas production. The proposed approach is based on adjusting process streams temperatures with the further synthesis of a new heat exchangers network and optimisation of the utility system. The potential of secondary energy resources was determined using plus/minus principles and simulation of a high-temperature co-electrolysis unit. The proposed technique maximises the economic and environmental benefits of inter-unit integration. Two scenarios were considered for sharing the high-temperature co-electrolysis and the Fischer-Tropsch process. In the first scenario, by-products from the Fischer-Tropsch process were used as fuel for a high-temperature co-electrolysis. Optimisation of secondary energy sources and the synthesis of a new heat exchanger network reduce fuel consumption by 47% and electricity by 11%. An additional environmental benefit is reflected in emission reduction by 25,145 tCO₂/y. The second scenario uses fossil fuel as a primary energy source. The new exchanger network for the high-temperature co-electrolysis was built for different energy sources. The use of natural gas resulted in total annual costs of the heat exchanger network to 1,388,034 USD/y, which is 1%, 14%, 116% less than for coal, fuel oil and LPG, respectively. The use of natural gas as a fuel has the lowest carbon footprint of 7288 tCO₂/y. On the other hand, coal as an energy source has commensurable economic indicators that produce 2 times more CO₂, which can be used as a feedstock for a high-temperature co-electrolysis. This work shows how in-depth preliminary analysis can optimise the use of primary and secondary energy resources during inter-plant integration.     

Pollutant emissions,performance and combustion behaviour assessment of an Si gas engine fuelled with Lcv gas containing carbon monoxide and hydrogen diluted by nitrogen

This paper includes the experimental test data of an SI engine fuelled with simulated LCV gas (Low Calorific Value), which resembles synthesis gas in composition. The LCV gas was simulated by a mixture of carbon monoxide, hydrogen and nitrogen. During the experiment, the lower heating value of the LCV gas was altered by dilution with nitrogen. A single-cylinder Honda GX270 engine was adopted in the experiment to assess the impact of LCV gas on the system performance. This engine is typically used to power various machines and for electrical energy production in small generator sets. A modified engine was connected to an electric generator, which was loaded with an electric resistor. Engine operation was controlled using a microprocessor controller. All tests were performed at constant engine speed (3000 rpm). The engine was working at wide-open throttle for all mixtures. All mixtures were burned at stoichiometric conditions and with fixed value of ignition timing (30 deg bTDC). The indicated performance of the SI engine was evaluated based on the in-cylinder pressure measurements. No significant impact on the main internal parameters of the tested SI engine fuelled with simulated LCV gas diluted by nitrogen was observed. The experimental tests showed that the combustion duration increased for the mixtures with higher content of inert gas. Increase in the LHV raised the specific emissions of NO_x and decreased specific emissions of CO and HC.     

A review on current trends in potential use of metal-organic framework for hydrogen storage

Hydrogen can be a promising clean energy carrier for the replenishment of non-renewable fossil fuels. The set back of hydrogen as an alternative fuel is due to its difficulties in feasible storage and safety concerns. Current hydrogen adsorption technologies, such as cryo-compressed and liquefied storage, are costly for practical applications. Metal-organic frameworks (MOFs) are crystalline materials that have structural versatility, high porosity and surface area, which can adsorb hydrogen efficiently. Hydrogen is adsorbed by physisorption on the MOFs through weak van der Waals force of attraction which can be easily desorbed by applying suitable heat or pressure. The strategies to improve the MOFs surface area, hydrogen uptake capacities and parameters affecting them are studied. Hydrogen spill over mechanism is found to provide high-density storage when compared to other mechanisms. MOFs can be used as proton exchange membranes to convert the stored hydrogen into electricity and can be used as electrodes for the fuel cells. In this review, we addressed the key strategies that could improve hydrogen storage properties for utilizing hydrogen as fuel and opportunities for further growth to meet energy demands.     

Life Cycle Assessment (LCA) for use on renewable sourced hydrogen fuel cell buses vs diesel engines buses in the city of Rosario,Argentina

The purpose of this paper is to build the first Energy and Life Cycle Analysis (LCA) comparison between buses with internal combustion engine currently used in the city of Rosario, Province of Santa Fe, Argentina, and some technological alternatives and their variants focusing on buses with an electrical engine powered by compressed hydrogen that feet fuel cells of polymer electrolyte membrane (PEM). This LCA comprehend raw material extraction up to its consumption as fuel. Specifically, hydrogen production considering different production processes from renewable sources called “green hydrogen” (Velazquez Abad and Dodds, 2020) [1] and non-renewable sources called “grey hydrogen” (Velazquez Abad and Dodds, 2020) [1]. Renewable sources for hydrogen production are rapid cut densified poplar energy plantation, post-industrial wood residues such as chips pallets, and maize silage. For non-renewable hydrogen production sources are the local electrical power grid from water electrolysis and natural gas from the steam methane reforming process.Buses whose fuel would be renewable hydrogen, produced near the City of Rosario, Province of Santa Fe, Argentina, meet one of the main criteria of sustainability biofuels of the European Union (EU) taken into account Renewable Energy Directive (RED) 2009/28 [2] and EU RED Directive 2018/2001 [3] that need significant reduction on net greenhouse gases (GHG) from biomass origin row material respect fossil fuels. At least 70% of GHG would be avoided from its main fossil counterpart of the intern combustion engine (ICE), in the worst and current scenario of the emission factor of the electrical grid of Argentina in the point of use that is about 0.40 kg CO_2eq/kWh with energy and environmental load of 100% in the allocation factor in the hydrogen production stage of the LCA analysis.     

On the economics of a hydrogen bus fleet powered by a wind park – A case study for Austria

This paper investigates the economics of a fuel cell bus fleet powered by hydrogen produced from electricity generated by a wind park in Austria. The main research question is to simultaneously identify the most economical hydrogen generation business model for the electric utility owning wind power plants and to evaluate the economics of operating a fuel cell bus fleet, with the core objective to minimize the total costs of the overall fuel supply (hydrogen production) and use (bus and operation) system. For that, three possible operation modes of the electrolyzer have been identified and the resulting hydrogen production costs calculated. Furthermore, an in-depth economic analysis of the fuel cell buses as well as the electrolyzer technology has been conducted. Results show that investment costs are the largest cost factor for both technologies. Thus, continuous hydrogen production with the smallest possible electrolyzer is the economically most favorable option. In such an operation mode (power grid), the costs of production per kg/H₂ were the lowest. However, this means that the electrolyzer cannot be solely operated with electricity from the wind park, but is also dependent on the electricity mix from the grid. For fuel cell buses, the future cost development will depend very much on the respective policies and funding programs for the market uptake, as to date, the total cost of use for the fuel cell bus is more than two times higher than the diesel bus. The major final conclusion of this paper is that to make fuel cell electric busses competitive in the next years today severe policy interferences, such as subsidies for these busses as well as electrolyzers and bans for fossil energy, along with investments in the setup of a hydrogen infrastructure, are necessary.     

Hydrogen production from phototrophic microorganisms: Reality and perspectives

Hydrogen is a promising alternative to fossil fuel for a source of clean energy due to its high energy content. Some strains of phototrophic microorganisms are known as important object of scientific research and they are being explored to raise biohydrogen (BioH₂) yield. BioH₂ is still not commonly used in industrial area because of the low biomass yield and valuable down streaming process. This article deals with the methods of the hydrogen production with the help of two large groups of phototrophic microorganisms – microalgae and cyanobacteria. Microalgal hydrogen is environmentally friendly alternative to conventional fossil fuels. Algal biomass has been considered as an attractive raw source for hydrogen production. Genetic modified strains of cyanobacteria are used as a perspective object for obtaining hydrogen. The modern photobioreactors and outdoor air systems have been used to obtain the biomass used for hydrogen production. At present time a variety of immobilization matrices and methods are being examined for their suitability to make immobilized H₂ producers.     

The production and application of hydrogen in steel industry

Due to the increasingly serious environmental issues and continuous depletion of fossil resources, the steel industry is facing unprecedented pressure to reduce CO₂ emissions and achieve the sustainable energy development. Hydrogen is considered as the most promising clean energy in the 21st century due to the diverse sources, high calorific value, good thermal conductivity and high reaction rate, making hydrogen have great potential to apply in the steel industry. In this review, different hydrogen production technologies which have potential to provide hydrogen or hydrogen-rich gas for the great demand of steel plants are described. The applications of hydrogen in the blast furnace (BF) production process, direct reduction iron (DRI) process and smelting reduction iron process are summarized. Furthermore, the functions of hydrogen or hydrogen-rich gas as fuels are also discussed. In addition, some suggestions and outlooks are provided for future development of steel industry in China.     

Hydrogen-powered vehicles for autonomous ride-hailing fleets

Autonomous ride-hailing fleets are approaching commercialization as an on-demand, low-cost transportation solution. Although battery electric vehicles (BEVs) are well-studied for this application, hydrogen fuel cell electric vehicles (FCEVs) may provide additional advantages that have not been sufficiently investigated. Here, we developed a stochastic ride-hailing autonomous vehicle (RHAV) model to compare these technologies and applied this model to seven BEVs and two FCEVs. FCEV fleets are 3–10% smaller than BEV fleets due to shorter refueling times and greater driving ranges, which enable greater fleet efficiency. The Hyundai Kona (BEV) provides the greatest fleet profitability; however, the Toyota Mirai (FCEV) is only 3% less profitable despite having a 25% higher purchase price. We demonstrate that FCEVs are economically competitive as RHAVs, and that expected price reductions can make them the most profitable technology. Furthermore, FCEV fleets provide qualitative benefits, including a substantial increase in local hydrogen demand to catalyze hydrogen infrastructure development.     

Development of a hydrogen impurity analyzer based on mobile-gas chromatography for online hydrogen fuel monitoring

Hydrogen is an excellent alternative energy source, particularly for vehicles. Despite the expansion of a considerable number of infrastructures, such as hydrogen refueling stations, there is a lack of efficient inspection methods for monitoring the hydrogen fuel quality. In this study, a hydrogen impurity analyzer (HIA) based on mobile gas chromatography with a thermal conductivity detector is developed and evaluated for the quality assurance of hydrogen fuel. Accordingly, O₂, N₂, and Ar which help in monitoring air leaks at hydrogen refueling stations, and CH₄, which can also be detected by HIA, are selected as target impurities. The HIA reached limits of detection of 2.93, 0.72, 0.84, and 1.54 μmol/mol for O₂, Ar, N₂, and CH₄, respectively. Moreover, the ISO 14687 requirements are satisfied with respective HIA expanded uncertainties of 2.6, 8.7, 8.2, and 9.4% (coverage factor k = 2). The developed system is ISO-compliant and offers enhanced mobility for online inspections.