Engineering MIL-88B crystallites for enhanced H2 uptake capacity: The role of ultramicropores

In this study, a strategy that optimizes the pore size to enhance the adsorbed H₂ amount (at 298 K) is investigated. Pore size and ultramicropore fraction (ultramicropore volume/total pore volume) were controlled by Fe:TPA ratio. The highest H₂ adsorption capacity of 0.47 wt% (298 K and 7.6 bar) belongs to MIL-88B-3, which is higher than those of reported metal-organic frameworks (MOFs) (MIL-100, MIL-101 [Cr], HKUST-1, MOF-5, and ZIF-8). The enhanced H₂ sorption capacity (1.96 times) is a consequence of the high fraction (89%) and volume (0.22 cm³/g) of ultramicropores with pore diameters of 0.6 nm. Our results demonstrate that pore size, fraction, and volume of ultramicropores control the amount of H₂ adsorbed also at 298 K. With the use of perturbation assisted nanofusion synthesis strategy that introduces textural pores to the pore structure, a Brunauer-Emmett-Teller (BET) surface area higher than those of reported MIL-88Bs has been achieved, and a strategy to synthesize MOFs with enhanced H₂ sorption capacities is suggested.     

Polyaniline sensitized Pt@TiO2 for visible-light-driven H2 generation

Polyaniline is a typical conducting polymer with high migration electron rate, good stability, eco-friendly properties, and high absorption coefficients for visible light. In the present study, polyaniline decorated Pt@TiO₂ for visible light-driven H₂ generation is reported for the first time. The above-mentioned nanocomposite is prepared through a simple oxidative-polymerization and characterized by infrared spectroscopy, transmission electron microscopy, X–ray diffraction, thermogravimetric analysis, and ultraviolet–visible diffuse reflectance spectra. Polyaniline modification improves the absorption of the nanocomposite in visible light region via a photosensitization effect similar to dye–sensitization but does not influence the crystal structure and size of Pt@TiO₂. The polyaniline modified Pt@TiO₂ exhibits a remarkable visible light activity (61.8 μmol h⁻¹ g⁻¹) and good stability for H₂ generation (with an average apparent quantum yield of 10.1%) with thioglycolic acid as an electron donor. This work provides new insights into using conducting polymers, including polyaniline, as a sensitizer to modify Pt@TiO₂ for visible-light hydrogen generation.     

Preparation and improvement of nickel catalyst supported ordered mesoporous spherical silica for thermocatalytic decomposition of methane

The thermocatalytic alteration of CH₄ into highly pure hydrogen and filaments of carbon was investigated on a series of Ni-catalysts with various contents (25, 40, 55, and 70 wt%) supported mesoporous spherical SiO₂. The silica with ordered structure and high specific surface area (1136 m²/g) was synthesized using the Stöber technique with TEOS as a silica precursor and CTAB as the template in a simple synthesis system of aqueous-phase. This technique led to the preparation of mesoporous spherical silica. The prepared samples were characterized using BET, TPR, XRD, TPO, and SEM analyses. The prepared catalysts with different nickel loading showed the BET surface area ranging from 225.0 to 725.7 m²/g. These results indicated that an increase in nickel content decreases the surface area and leads to a subsequent collapse of a pore structure. SEM analysis confirmed a spherical nanostructure of catalysts and revealed that with the increase in loading of Ni, the particle size enlarged, because of the agglomeration of the particles. The results implied that the high methane conversion of 54% obtained over the 55 wt% Ni/SiO₂ at 575 °C and this sample had higher stability at lower reaction temperature than the other prepared catalysts, slowly deactivation was observed for this catalyst at a period of 300 min of time on stream.     

Effect of physical activation/surface functional groups on wettability and electrochemical performance of carbon/activated carbon aerogels based electrode materials for electrochemical capacitors

Polymeric carbon/activated carbon aerogels were synthesized through sol-gel polycondensation reaction followed by the carbonization at 800 °C under Argon (Ar) atmosphere and subsequent physical activation under CO₂ environment at different temperatures with different degrees of burn-off. Significant increase in BET specific surface area (SSA) from 537 to 1775 m²g⁻¹ and pore volume from 0.24 to 0.94 cm³g⁻¹ was observed after physical activation while the pore size remained constant (around 2 nm). Morphological characterization of the carbon and activated carbons was conducted using X-ray diffraction (XRD) and Raman spectroscopy. Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) were used to investigate the effect of thermal treatment (surface cleaning) on the chemical composition of carbon samples.Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to analyse the capacitive and resistive behaviour of non-activated/activated/and surface cleaned activated carbons employed as electroactive material in a two electrode symmetrical electrochemical capacitor (EC) cell with 6 M KOH solution used as the electrolyte.CV measurements showed improved specific capacitance (SC) of 197 Fg⁻¹ for activated carbon as compared to the SC of 136 Fg⁻¹ when non-activated carbon was used as electroactive material at a scan rate of 5 mVs⁻¹. Reduction in SC from 197 Fg⁻¹ to 163 Fg⁻¹ was witnessed after surface cleaning at elevated temperatures due to the reduction of surface oxygen function groups.The result of EIS measurements showed low internal resistance for all carbon samples indicating that the polymeric carbons possess a highly conductive three dimensional crosslinked structure. Because of their preferred properties such as controlled porosity, exceptionally high specific surface area, high conductivity and desirable capacitive behaviour, these materials have shown potential to be adopted as electrode materials in electrochemical capacitors.     

Titanate quantum dots-sensitized Cu2S nanocomposites for superficial H2 production via photocatalytic water splitting

TiO₂ quantum dots-sensitized Cu₂S (Cu₂S/TiO₂) nanocomposites with varying concentration of TiO₂ QDs are synthesized via a facile two-stage hydrothermal-wet impregnation method. X-ray diffraction analysis confirms the formation of Cu₂S and TiO₂with chalcocite and anatase phases, respectively. The observed shoulder-like absorption peaks indicate the UV–visible light-driven properties of the composite. Morphological analysis reveals that the fabricated Cu₂S/TiO₂ composite consists of Cu₂S with a nano rod-like shape (average length and width of ～856 and ～213 nm, respectively) and nanosheets-like structures (average length and width of ～283 and ～289 nm, respectively), whereas the TiO₂ is formed as quantum dots with a size range of 8.2 ± 0.4 nm. Chemical state analysis shows the presence of Cu⁺, S^2?, Ni²⁺, and O^2? in the nanocomposite. The H₂ evolution rate over the optimized photocatalyst is found to be ～45.6 mmol h^?1g^?1_cat under simulated solar irradiation, which is around 5 and 2.4-fold higher than that of the pristine TiO₂ and Cu₂S, respectively. Continuous H₂ production for 30 h is achieved during time-on-stream experiments, demonstrating the excellent stability and durability of the Cu₂S/TiO₂ photocatalyst for large-scale applications.     

Steam reforming of 1-methylnaphthalene over pure CeO2 under model coke oven gas conditions containing high H2S concentrations

Tar and H₂S are obstacles to the efficient production of H₂ from unused industrial gases and biomass gasification gases. Robust catalysts against tar and H₂S are required to produce H₂ from such resources. Herein, a stable steam reforming reaction is demonstrated over pure CeO₂ under reaction conditions consisting of ~2 vol% 1-methylnaphthalene and ~1000 ppm H₂S. The presence of H₂S significantly suppressed Ni/MgO/Al₂O₃ activity and increased carbon deposition, regardless of the steam to carbon (S/C) ratio. In contrast, the promotion or suppression of CeO₂ activity in the presence of H₂S was dependent on the S/C ratio. At S/C = 1.2, H₂S deactivated the CeO₂ catalyst and increased carbon deposition. Conversely, H₂S promoted the reforming reaction and decreased carbon deposition on CeO₂ at S/C ≥ 2.0. The results of this study clarify that pure CeO₂ exhibits outstanding and stable activity for the steam reforming reaction of 1-methylnaphthalene in the presence of H₂S by controlling the S/C of the inlet gas.     

Simultaneous biohydrogen (H2) and bioplastic (poly-β-hydroxybutyrate-PHB) productions under dark,photo, and subsequent dark and photo fermentation utilizing various wastes

The present study is focused on bio hydrogen (H₂) and bioplastic (i.e., poly-β-hydroxybutyrate; PHB) productions utilizing various wastes under dark fermentation, photo fermentation and subsequent dark-photo fermentation. Potential bio H₂ and PHB producing microbes were enriched and isolated. The effects of substrate (rice husk hydrolysate, rice straw hydrolysate, dairy industry wastewater, and rice mill wastewater) concentration (10–100%) and pH (5.5–8.0) were examined in the batch mode under the dark and photo fermentation conditions. Using 100% rice straw hydrolysate at pH 7, the maximum bio H₂ (1.53 ± 0.04 mol H₂/mol glucose) and PHB (9.8 ± 0.14 g/L) were produced under dark fermentation condition by Bacillus cereus. In the subsequent dark-photo fermentation, the highest amounts of bio H₂ and PHB were recorded utilizing 100% rice straw hydrolysate (1.82 ± 0.01 mol H₂/mol glucose and 19.15 ± 0.25 g/L PHB) at a pH of 7.0 using Bacillus cereus (KR809374) and Rhodopseudomonas rutila. The subsequent dark-photo fermentative bio H₂ and PHB productions obtained using renewable biomass (i.e., rice husk hydrolysate and rice straw hydrolysate) can be considered with respect to the sustainable management of global energy sources and environmental issues.     

HRT control as a strategy to enhance continuous hydrogen production from sugarcane juice under mesophilic and thermophilic conditions in AFBRs

The objective of this study was to evaluate the effects of hydraulic retention time (HRT) (8–1 h) on H₂ production from sugarcane juice (5000 mg COD L⁻¹) in mesophilic (30 °C, AFBR-30) and thermophilic (55 °C, AFBR-55) anaerobic fluidized bed reactors (AFBRs). At HRTs of 8 and 1 h in AFBR-30, the H₂ production rates were 60 and 116 mL H₂ h⁻¹ L⁻¹, the hydrogen yields were 0.60 and 0.10 mol H₂ mol⁻¹ hexose, and the highest bacterial diversities were 2.47 and 2.34, respectively. In AFBR-55, the decrease in the HRT from 8 to 1 h increased the hydrogen production rate to 501 mL H₂ h⁻¹ L⁻¹ at the HRT of 1 h. The maximum hydrogen yield of 1.52 mol H₂ mol⁻¹ hexose was observed at the HRT of 2 h and was associated with the lowest bacterial diversity (0.92) and highest bacterial dominance (0.52).     

Novel sonochemical synthesis of Zn2V2O7 nanostructures for electrochemical hydrogen storage

Although utilization of diverse classes of metal oxides as hydrogen storage materials has been reported, but there is still a major need to introduce efficient materials. Herein, mesoporous Zn₂V₂O₇ nanostructures were produced by a new sonochemical method using hydrazine, zinc nitrate, and ammonium vanadate as the starting reagents and then annealed at 700 °C. Prior to annealing, Zn₃V₃O₈ was produced in the presence of ultrasonic waves, whereas in the absence of ultrasonic waves, Zn₂(VO₄)₂ was the major product. In fact, ultrasonic waves interfered with the reaction mechanism and reduced V⁵⁺ to V⁴⁺ and V³⁺. Because of the proper composition and structure of these nanostructures, they were used for electrochemical storage of hydrogen. Storage of over 2899 mAh/g after 20 cycles by flower-like nanostructures revealed their high capability. The results also showed that morphology affects efficiency such that three-dimensional spherical nanostructures had a storage capacity of 2247 mAh/g after 20 cycles.     

Enhanced hydrogen storage performance of Cu3(BTC)2 in situ inserted with few-layer silicon-based nanosheets

Silicon-based nanosheets (SNS) were synthesised via a mild (60 °C) and time-saving (8 h) modified topochemical method. Then, Cu₃(BTC)₂ and SNS@Cu₃(BTC)₂ were successfully synthesised by microwave irradiation, and their characteristics and hydrogen storage performance were analysed by multiple techniques. The accordion-like SNS exhibited void spaces, a unique low buckled structure, and ultrathin, almost transparent, loosely stacked layers with a high specific surface area (362 m²/g). After in-situ synthesis with Cu₃(BTC)₂, the SNS compound achieved a high specific surface area (1526 m²/g), outstanding hydrogen storage performance (5.6 wt%), and a desirable hydrogen diffusion coefficient (10^?7). Thus, SNS doping improved the hydrogen storage performance of Cu₃(BTC)₂ by 64% through electron transfer reactions with Cu enabled by the unique composite nanostructure of SNS@Cu₃(BTC)₂. This study presents a promising method of synthesising SNS and porous composite materials for hydrogen storage.     

Improvement of biohydrogen production from brewery wastewater: Evaluation of inocula,support and reactor

This work explores the production of biohydrogen from brewery wastewater using as inoculum a culture produced by natural fermentation of synthetic wastewater and Klebsiella pneumoniae isolated from the environment. Klebsiella pneumoniae showed good performance as inoculum, as evaluated using assays of between 9 and 16 cycles, with durations of 12 and 24 h, carbohydrate concentrations from 2.79 to 7.22 g L⁻¹, and applied volumetric organic loads from 2.6 to 12.6 g carbohydrate L⁻¹ day⁻¹. The best results were achieved with applied volumetric organic loads of 12.6 g carbohydrate L⁻¹ day⁻¹ and cycle length of 12 h, resulting in mean volumetric productivity of 0.88 L H₂ L⁻¹ day⁻¹, maximum molar flow of 10.80 mmol H₂ h⁻¹, and mean yield of 0.70 mol H₂ mol⁻¹ glucose consumed. The biogas H₂ content was between 18 and 42%, while the mean organic compounds removal and carbohydrate conversion efficiencies were 23 and 81%, respectively. The inoculum produced by natural fermentation was not viable.     

Determination of the potential of cyanobacterial strains for hydrogen production

Hydrogen (H₂) is a renewable, abundant, and nonpolluting source of energy. Photosynthetic organisms capture sunlight very efficiently and convert it into organic molecules. Cyanobacteria produce H₂ by breaking down organic compounds and water. In this study, biological H₂ was produced from various strains of cyanobacteria. Moreover, H₂ accumulation by Synechocystis sp. PCC 6803 was as high as 0.037 μmol/mg Chl/h within 120 h in the dark. The wild-type, filamentous, non-heterocystous cyanobacterium Desertifilum sp. IPPAS B-1220 was found to produce a maximum of 0.229 μmol/mg Chl/h in the gas phase within 166 h in the light, which was on par with the maximum yield reported in the literature. DCMU at 10 μM increased H₂ production by Desertifilum sp. IPPAS B-1220 by 1.5-fold to 0.348 μmol H₂/mg Chl/h. This is the first report on the capability of Desertifilum cyanobacterium to produce H₂.     

Enhancement of bio-hydrogen generation by spirulina via an electrochemical photo-bioreactor (EPBR)

The biological production of hydrogen by microalgae is considered as an advantageous process. However, its yields are sometimes limited. To go beyond this limit, the improvement of the H₂ generation rate by Spirulina was studied via an electrochemical photo-bioreactor (EPBR). This EPBR led to hydrogen evolution rates of up to 27.49 and 13.37 mol of H₂.d⁻¹.m⁻³ for the anode and cathode chambers, respectively, under 0.3 V voltage and ~2.5 mA current. These results represent about a 4-fold increase compared to the H₂ production rate recorded without the application of a voltage. This increase in bio-hydrogen production is correlated with a drop in the concentration of NADPH. The Electrochemical Sequential Batch Reactor (ESRB) provided a more interesting total production rate which was 2.65 m³ m⁻³ d⁻¹, compared to the batch mode, which gave 1.2 m³ m⁻³.d⁻¹. The results show, for the first time, the boosting effect of the voltage on the metabolism of H₂ production by the Spirulina strain.     

Dark fermentative biohydrogen production using pretreated Scenedesmus obliquus biomass under an integrated paradigm of biorefinery

In recent times, biohydrogen production from microalgal feedstock has garnered considerable research interests to sustainably replace the fossil fuels. The present work adapted an integrated approach of utilizing deoiled Scenedesmus obliquus biomass as feedstock for biohydrogen production and valorization of dark fermentation (DF) effluent via biomethanation. The microalgae was cultivated under different CO₂ concentration. CO₂-air sparging of 5% v/v supported maximum microalgal growth and carbohydrate production with CO₂ fixation ability of 727.7 mg L^?1 d^?1. Thereafter, lipid present in microalgae was extracted for biodiesel production and the deoiled microalgal biomass (DMB) was subjected to different pretreatment techniques to maximize the carbohydrate recovery and biohydrogen yield. Steam heating (121 °C) in coherence with H₂SO₄ (0.5 N) documented highest carbohydrate recovery of 87.5%. DF of acid-thermal pretreated DMB resulted in maximum H₂ yield of 97.6 mL g^?1 VS which was almost 10 times higher as compared to untreated DMB (9.8 mL g^?1 VS). Subsequent utilization of DF effluent in biomethanation process resulted in cumulative methane production of 1060 mL L^?1. The total substrate energy recovered from integrated biofuel production system was 30%. The present study envisages a microalgal biorefinery to produce biohydrogen via DF coupled with concomitant CO₂ sequestration.     

Energy efficient hydrogen drying and purification for fuel cell vehicles

High-purity standards are required for hydrogen used in fuel cell vehicles. The relative abundance of contaminants is highly influenced by the production pathway. Hydrogen obtained from water electrolysis presents three main pollutants: Nitrogen, Oxygen and Water. Herein, the engineering and implementation of removal techniques in a commercial 50 kW alkaline electrolyzer are reported. The full system was characterized with various analytical techniques including gas chromatography and mass spectrometry. A reduction of contaminant levels compatible with ISO 14687:2019 standard was achieved. From cold start, 100 min of operation are required to reach the desired nitrogen levels. Oxygen was removed in one step with a catalytic converter. Drying of hydrogen was achieved by using an innovative vacuum assisted pressure swing adsorption system. Sub-ppm levels of water are obtained with a power consumption of only 0.5 kWh/kg H₂ and 98.4% of product recovery.     

Kinetics of formic acid decomposition in subcritical and supercritical water – a Raman spectroscopic study

The decomposition of formic acid is studied in a continuous sub- or supercritical water reactor at temperatures between 300 and 430 °C, a pressure of 25 MPa, residence times between 4 and 65 s, and a feedstock concentration of 3.6 wt%. In situ Raman spectroscopy is used to produce real-time data and accurately quantify decomposition product yields of H₂, CO₂, and CO. Collected spectra are used to determine global decomposition rates and kinetic rates for individual reaction pathways. First-order global Arrhenius parameters are determined as log A (s⁻¹) = 1.6 ± 0.20 and E_A = 9.5 ± 0.55 kcal/mol for subcritical decomposition, and log A (s⁻¹) = 12.56 ± 1.96 and E_A = 41.90 ± 6.08 kcal/mol for supercritical decomposition. Subcritical and supercritical Arrhenius parameters for individual pathways are proposed. The variance in rate parameters is likely due to changing thermophysical properties of water across the critical point. There is strong evidence for a surface catalyzed free-radical mechanism responsible for rapid decomposition above the critical point, facilitated by low density at supercritical conditions.     

Continuous H2 production during fermentation of the carbon components of lignocellulose hydrolysates: Insight into the influence of pH conditions on the conversion efficiency of individual sugars

Sugars released from lignocellulose biomass are a promising substrate for biohydrogen production. This study evaluates the effect of pH controlled between 4.0 and 7.5 on continuous dark-fermentative H₂ production from the mixture of cellobiose, xylose and arabinose. High hydrogen production rate was obtained for pH values between 6.0 and 7.0 with a maximum of 7.41 ± 0.16 L/L-d at pH 7.0. On the other hand, the highest H₂ yields of around 1.74 ± 0.02 mol/mol_consumed were obtained at pH 4.5, 5.0 and 6.0. Cellobiose was completely utilized in nearly the entire pH range, while the highest consumption of xylose and arabinose was obtained at pH 6.0 and 7.0, respectively. It shows the challenges in selecting optimum pH for fermentation of mixed sugars. Significant impact of pH conditions on the microbial structure was observed. Between pH 4.0 and 7.0 Clostridium genus dominated the consortium, while above pH 7.0 relative abundance of Bacillus genus increased significantly.     

Effect of ZrO2 on the performance of Co–CeO2 catalysts for hydrogen production from waste-derived synthesis gas using high-temperature water gas shift reaction

In this study, highly active and stable CeO₂, ZrO₂, and Zr_(1-x)Ce_(x)O₂-supported Co catalysts were prepared using the co-precipitation method for the high-temperature water gas shift reaction to produce hydrogen from waste-derived synthesis gas. The physicochemical properties of the catalysts were investigated by carrying out Brunauer-Emmet-Teller, X-ray diffraction, CO-chemisorption, Raman spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and H₂-temperature-programmed reduction measurements. With an increase in the ZrO₂ content, the surface area and reducibility of the catalysts increased, while the interaction between Co and the support and the dispersion of Co deteriorated. The Co–Zr_0.4Ce_0·6O₂ and Co–Zr_0.6Ce_0·4O₂ catalysts showed higher oxygen storage capacity than that of the others because of the distortion of the CeO₂ structure due to the substitution of Ce⁴⁺ by Zr⁴⁺. The Co–Zr_0.6Ce_0·4O₂ catalyst with high reducibility and oxygen storage capacity exhibited the best catalytic performance and stability among all the catalysts investigated in this study.     

Producing hydrogen from the fermentation of cheese whey and glycerol as cosubstrates in an anaerobic fluidized bed reactor

This study aimed to evaluate the effect of the organic loading rate (OLR) (60, 90, and 120 g Chemical Oxygen Demand (COD). L^?1. d^?1) on hydrogen production from cheese whey and glycerol fermentation as cosubstrates (50% cheese whey and 50% glycerol on a COD basis) in a thermophilic fluidized bed reactor (55 °C). The increase in the OLR to 90 gCOD.L^?1. d^?1 favored the hydrogen production rate (HPR) (3.9 L H₂. L^?1. d^?1) and hydrogen yield (HY) (1.7 mmol H₂. gCOD^?1_app) concomitant with the production of butyric and acetic acids. Employing 16S rRNA gene sequencing, the highest hydrogen production was related to the detection of Thermoanaerobacterium (34.9%), Pseudomonas (14.5%), and Clostridium (4.7%). Conversely, at 120 gCOD.L^?1. d^?1, HPR and HY decreased to 2.5 L H₂. L^?1. d^?1 and 0.8 mmol H₂. gCOD^?1_app, respectively, due to lactic acid production that was related to the genera Thermoanaerobacterium (50.91%) and Tumebacillus (23.56%). Cofermentation favored hydrogen production at higher OLRs than cheese whey single fermentation.