Characterization and acid-induced gelation of butter oil emulsions produced from heated whey protein dispersions

Whey protein isolate was dispersed at 4% or 8% (w/v) and heated at neutral pH to produce protein polymers. Butter oil, up to 20%, was homogenized in heated whey protein dispersions at pressure ranging from 10 to 120 MPa. Emulsion gelation was induced by acidification with glucono-δ-lactone. Whey protein polymers produced finely dispersed emulsions with fat droplet diameter ranging from 340 to 900 nm. Homogenization pressure was the main factor influencing droplet size. At low fat volume fraction, the emulsions exhibited Newtonian behaviour. As fat content increased, shear thinning behaviour developed as a result of depletion flocculation. Emulsion consistency index increased with protein and fat concentrations. Increasing homogenization pressure had no effect on Newtonian emulsions but promoted flocculation and significantly increased the consistency of high fat emulsions. Protein concentration was the main factor explaining emulsion gel hardness and syneresis. Syneresis decreased with increasing fat content in the gel.     

Physical and oxidative stability of whey protein oil-in-water emulsions produced by conventional and ultra high-pressure homogenization: Effects of pressure and protein concentration on emulsion characteristics

Oil-in-water pre-emulsions (15% sunflower + 5% olive oils) obtained by colloid mill homogenization (CM) at 5000 rpm using whey protein isolate at different levels (1, 2 and 4%) were stabilized by ultra high-pressure homogenization (UHPH, 100 and 200 MPa) and by conventional homogenization (CH, 15 MPa). Emulsions were characterized for their physical properties (droplet size distribution, microstructure, surface protein concentration, emulsifying stability against creaming and coalescence, and viscosity) and oxidative stability (hydroperoxide content and thiobarbituric acid reactive substances, TBARs) under light (2000 lux/m² for 10 days). UHPH produced emulsions with lipid droplets of small size in the sub-micron range (100–200 nm) and low surface protein with unimodal distribution when produced at 4% whey proteins and 200 MPa. All emulsions exhibited Newtonian behavior (n ≈ 1). Long term physical stability against creaming and coalescence was observed in UHPH-emulsions, compared to those obtained by CM and CH. However, CH emulsions were highly stable against creaming (days) in comparison to the CM emulsions (hours). UHPH resulted in emulsions highly stable to oxidation compared to CM and CH treatments, especially when 100 MPa treatment was applied.Industrial relevanceIn the food, cosmetic and pharmaceutical sectors, industrial operators are currently interested in developing encapsulating systems to delivery bioactive compounds, which are generally hydrophobic, unstable and sensitive to light, temperature or/and oxygen. Ultra high-pressure homogenization is capable of producing stable submicron emulsions (< 1 μm) with a narrow size distribution, inducing more significant changes in the interfacial protein layer thus preventing droplet coalescence and also inhibit lipid oxidation. The present study suggests that emulsions produced by whey protein (4%) treated by ultra high-pressure homogenization have a good physical stability to flocculation, coalescence and creaming and also high stability to lipid oxidation, opening a wide range of opportunities in the formulation of emulsions containing bioactive components with lipid nature.     

Effect of high pressure processing on the quality of acidified Granny Smith apple purée product

The aim of the present study was the evaluation of the physicochemical, nutritional and microbial quality of acidified Granny Smith (GS) apple purée processed on industrial-scale high pressure system during 3 weeks of refrigerated storage (5 °C ± 1 °C). Two commercially feasible pressure treatments (400 and 600 MPa/5 min/20 °C) and a mild conventional pasteurization at 75 °C/10 min, with pasteurization values of P_70°C^7.5 = 8.15 min, were conducted and their effect on total vitamin C (total Vit C), ascorbic acid (AA) and total phenolic content (TPP), and on instrumental quality parameters (color, viscosity, soluble solids, titratable acidity and pH) were comparatively studied. Inactivation of indigenous microorganisms (total aerobic mesophilic and psychrotrophic counts and moulds and yeasts) of the apple product was also studied and monitored during storage. Total Vit C and AA contents were unaffected by the 400 MPa and the mild pasteurization treatment. TPP content was not changed during processing at 400 MPa, but was affected by the 600 MPa and also slightly by the pasteurization treatment. Experimental data on the loss of total Vit C during storage were described with a first-order reaction kinetic and times of half loss between 9.3 to 10.3 days could be estimated for the three studied processes. Storage provoked loss of TPP content and color deterioration of pressurized GS puree samples, which was attributed to enzymatic browning reactions. Microbial counts were reduced by the different preservation techniques below the detection limit (50 cfu g^?1) and storage revealed no further growth.Industrial relevanceThis is one of the first studies applying commercial industrial-scale high pressure equipment for the pasteurization of an acidified apple purée product. The pressures of 400 and 600 MPa with 5 min holding time at ambient temperature render economically feasible processes with high throughput and productivity. In the European Union the most important fruits in terms of production are apples. Apple purée is a largely consumed preserve in many households and beside apple juice or cider is one of the most important apple products in the market. In contrast to traditional apple purée preparation, high pressure processing or mild thermal treatments could imply new opportunities for the apple processing industry in developing more fresh-like, value-added apple products with reasonable shelf life.     

Ultra-High Pressure Homogenization enhances physicochemical properties of soy protein isolate-stabilized emulsions

The effect of Ultra-High Pressure Homogenization (UHPH, 100–300 MPa) on the physicochemical properties of oil-in-water emulsions prepared with 4.0% (w/v) of soy protein isolate (SPI) and soybean oil (10 and 20%, v/v) was studied and compared to emulsions treated by conventional homogenization (CH, 15 MPa). CH emulsions were prepared with non-heated and heated (95 °C for 15 min) SPI dispersions. Emulsions were characterized by particle size determination with laser diffraction, rheological properties using a rotational rheometer by applying measurements of flow curve and by transmission electron microscopy. The variation on particle size and creaming was assessed by Turbiscan® analysis, and visual observation of the emulsions was also carried out. UHPH emulsions showed much smaller d_3.2 values and greater physical stability than CH emulsions. The thermal treatment of SPI prior CH process did not improve physical stability properties. In addition, emulsions containing 20% of oil exhibited greater physical stability compared to emulsions containing 10% of oil. Particularly, UHPH emulsions treated at 100 and 200 MPa with 20% of oil were the most stable due to low particle size values (d_3.2 and Span), greater viscosity and partial protein denaturation. These results address the physical stability improvement of protein isolate-stabilized emulsions by using the emerging UHPH technology.     

Yield and functionality of Cheddar cheese as influenced by homogenization of cream

Cheese milk was standardized (casein-to-fat ratio of 0.7) by blending 0.64% fat milk and 35% fat cream. Cream was homogenized at 0/0 MPa (CO), 3.5/3.5 MPa (H05), 6.9/3.5 MPa (H10) or 10.4/3.5 MPa (H15). Cream homogenization did not influence rennet-clotting time, but it increased rate of curd firming and increased curd firmness of cheese milk. Moisture and salt in moisture phase of cheese increased with homogenization. Moisture (37%) and salt (1.5%) adjusted yield increased 1.42, 3.44 and 3.85% in H05, H10 and H15, respectively, over CO. Homogenized treatment cheeses melted faster with age. Free oil in 1 week old cheeses was lowest in H10 and highest in H05 and increased in all treatments with age. Cheese hardness was not influenced by homogenization but decreased with age. Cheeses with homogenized cream had improved body and texture and flavor. Cream homogenized at 6.9/3.5 MPa was optimal for enhancing Cheddar cheese yield and functionality.     

Effect of cream homogenization on textural characteristics of low-fat Iranian White cheese

The effects of cream homogenization of cheese making milk on textural and sensory characteristics of Iranian White cheese were studied. Cream was homogenized in a two-stage homogenizer at 6.0/2.5 or 9.0/2.5 MPa. Cheese samples were analyzed for rheological parameters (uniaxial compression and small amplitude oscillatory shear), meltability, microstructure, and sensory characteristics. Cream homogenization increased fat content leading to increased meltability. This effect increased as the homogenization pressure increased. The values of storage modulus, stress at fracture and Young's modulus of elasticity for cheeses from homogenized treatments were lower than those of unhomogenized cheese. Cream homogenization at 6.0/2.5 MPa effectively improved the textural, functional and sensory characteristics and enhanced the yield of low-fat Iranian White cheese. This cheese had the lowest values of storage modulus and stress at fracture, probably due to the high number of small, evenly dispersed fat globules in microstructure and especially its lower protein content. Cheeses with homogenized cream had improved texture, flavor and appearance.     

Change of microbial and quality attributes of mango juice treated by high pressure homogenization combined with moderate inlet temperatures during storage

The effects of high pressure homogenization (HPH) on microbial inactivation and quality attributes (physio-chemical properties, bioactive components and antioxidant capacity) of mango juice, as well as their changes during storage at 4 °C and room temperature were investigated. Pressure levels ranged from 40 to 190 MPa, the inlet temperature from 20 °C to 60 °C and the number of passes from 1 to 5. Complete inactivation of molds and yeasts was achieved by 1 and 3 passes at 190 MPa and 60 °C, while total plate count was below 2.0 log₁₀ CFU/mL. No multiplication of microorganisms was observed in mango juice over 60 days of storage at 4 °C. HPH treatment could retain or even increase the carotenoids and total phenols by 11.8% and 21.4%, respectively, while significant reductions were found for heat treatment (HT) samples. During the storage of 60 days, HPH treatment also provided better preservation of color, bioactive components and antioxidant capacity of mango juice than HT.Industrial relevanceHigh pressure homogenization (HPH) is a novel non-thermal technique, particularly suitable for continuous production of liquid foods limiting thermal damage and promoting “freshness”. Results showed that high pressure homogenization had the advantage of notably reducing the microbial load to levels equivalent to thermal pasteurization. Moreover, HPH treatment was superior to heat treatment with regard to post-treatment levels of bioactive.     

Optimization of textural properties of reduced-fat and reduced-salt emulsion-type sausages treated with high pressure using a response surface methodology

This study optimized the high pressure conditions for development of a reduced fat sausage. A three-factor-three-level Box–Behnken design was adopted to study the simultaneous effects of one compositional variable (15, 20 and 25% fat content) and two processing variables (150, 200 and 250 MPa high pressure, along with 5, 6 and 7 min high pressure treatment time) on firmness of emulsion-type sausages. Analysis of variance (ANOVA) was performed to evaluate the potential interactive and quadratic effects between these variables. The results revealed that, the optimum processing conditions for an optimum gel setting were 22.19% fat content, 197.30 MPa high pressure and 5.92 min pressure treatment time. The adequacy of the model equation for predicting the optimum response values was effectively verified. In conclusion, the emulsion-type meat sausages using a novel high pressure based processing method were preferred for their improved textural properties and reduced fat content.Industrial relevanceFor health reasons, there is a need to reduce fat content of processed meat products. This study developed a novel processing method using high pressure to produce emulsion-type meat sausages with reduced-fat, with improved functional qualities, including objective appearance, textural properties and sensory evaluation. Importantly, this was achieved with a model, mainly based on prediction of the firmness of the pressure treated sausages with reduced fat contents.     

Application of high-pressure treatment on ovine brined cheese: Effect on composition and microflora throughout ripening

Ovine brined cheese was high-pressure (HP) treated at 200 or 500 MPa for 15 min at 20 °C on the 15th day of ripening. Compared to control cheese, HP treatment did not affect significantly (P > 0.05) the pH values, moisture, fat in dry matter, protein in dry matter and salt in moisture contents of cheeses at 90 days. The counts of total aerobic mesophilic bacteria, thermophilic lactococci, thermophilic lactobacilli and non starter lactic acid bacteria (NSLAB) were not affected by HP treatment of cheese at 200 MPa throughout ripening. After 90 days of ripening, the same microbial groups in cheese treated at 500 MPa were about 1.2, 3.6, 2.1 and 4 log units lower than in control cheese respectively. Coliforms were reduced faster at non detectable levels in HP treated cheeses than in control cheese. Regarding the bacterial enzymatic activities in cheese, aminopeptidase activity (Apep) was marginally favoured by both HP treatments. However, its activity was decreased at 90 days due probably to loss in brine. In contrast, lactate dehydrogenase (LDH) activity, following the bacteria cell lysis, was negatively affected by HP treatment at 500 MPa throughout ripening.Industrial relevanceThe data obtained from this work suggest that application of HP treatment under optimized conditions on ovine cheese in brine can be used to reduce effectively the undesirable microbial load in it and to cause moderate enhancement of aminopeptidase activity, without modifying its composition.     

Effect of cooling rate on lipid crystallization in oil-in-water emulsions

The effect of cooling rate on the destabilization of oil-in-water (o/w) emulsions was studied as a function of oil content (20% and 40% o/w), homogenization conditions, and crystallization temperatures (10, 5, 0, ?5 and ?10 °C). The lipid phase was a mixture of anhydrous milk fat and soybean oil, and whey protein was used as the emulsifier. Differential scanning calorimetry was used to analyze the crystallization and melting behaviors; while a vertical scan macroscopic analyzer measured the physicochemical stability. Slow cooling rate increased the stability of emulsions with 20% oil. In addition, slow cooling promoted the onset of crystallization and delayed crystal growth. These effects were more significant in emulsions formulated with 20% oil and formulated under processing conditions that resulted in bigger droplet sizes (～0.9 μm).     

Assessing the potential of flaxseed protein as an emulsifier combined with whey protein isolate

The potential use of flaxseed protein isolate (FPI) as an emulsifying agent was studied in combination with whey protein isolate (WPI) or alone. All the FPI and WPI–FPI emulsions were kinetically unstable. The increase of FPI concentration (0.7% w/v) led to a higher creaming stability of the FPI emulsions due partly to a reduction in interfacial tension between aqueous and oil phases, but mainly to the gel network formation. However at this same high FPI concentration, WPI–FPI emulsions showed a decrease in droplet size and creaming stability, which could be due to the presence of flaxseed gum in the protein isolate enhancing depletion effects. A protein excess was verified in the mixed systems (0.14 or 0.7% (w/v) FPI) and the increase of FPI concentration led to an even greater surface protein content. Increasing homogenization conditions (pressure and number of passes), the creaming stability of the FPI systems increased, mainly at higher concentration (0.7% w/v). Meanwhile, in the mixed systems, the creaming stability of the emulsions containing 0.7% (w/v) FPI decreased even more, but was improved for the emulsions with 0.14% (w/v) FPI. Thus, it was observed that systems containing only FPI at higher concentration were stabilized by gel formation, while in WPI–FPI systems there was a competition by interface between biopolymers with a consequent depletion process. As a result, more stable systems were obtained with WPI addition at lower FPI concentration (0.14% w/v) and using higher homogenization pressure and number of passes (60 MPa, two passes).     

Influence of processing conditions on reducing γ-aminobutyric acid content during fortified milk production

The work studied the effects of processing conditions on the γ-aminobutyric acid (GABA) loss during fortified milk production. Bovine milk or their proteins/lactose fractions (0.66% whey protein and 2.6% casein or 4.9% lactose, w/v) containing 0.05–1.0% added γ-aminobutyric acid (w/w, based on bulk milk or these fractions) were subjected to a simulated milk technological process as following the sequential preheating (25–60 °C), homogenization (0–20 MPa), and pasteurization (62 °C/30 min, 72 °C/15 s, 95 °C/5 min, and 138 °C/2 s) or their unit processes to treat GABA. The resulting samples were characterized through GABA and lactose concentrations under various processing conditions. The amine and carboxyl groups and the structural characteristics of the resulting protein (lactose) were also examined through their concentrations (for lactose) and mass/spectral analyses, respectively. The results showed that the increase in temperature significantly promoted a reduction in GABA content. Whey protein fractions than caseins were primarily responsible for inducing GABA, whereas lactose had no remarkable effect on it. The rationale for GABA reduction is potential reactions with milk proteins/lactose, which preliminarily confirmed by the measurement of protein modification and lactose mass spectrometry.     

Influence of high isostatic pressure on structural and functional characteristics of potato protein

Potato protein possesses promising nutritional and techno-functional properties, but distinct heat sensitivity. Therefore, the potential of high isostatic pressure as an alternative preservation and modification method was investigated. Pressures of 200, 400 and 600 MPa were applied at isothermal conditions of 20 and 40 °C to dispersions made of potato protein concentrate and isolated patatin for dwell times of 10 min. Process induced changes in solubility, foaming properties and selected structural characteristics were compared to results of pure thermal treatments from 20 to 80 °C. Potato protein solubility in neutral solutions made of concentrate was reduced to 21% after heating to 70 and 80 °C whereas it only decreased to 74% after pressurization at 600 MPa. Processing of isolated patatin at pH 6 and pH adjustment from 7 to 6 after processing reduced protein solubility to 12% for heat treatments and to 55 and 89%, respectively, for pressure treatments indicating different denaturation or aggregation mechanisms. Hydrogen bonds and hydrophobic interactions were involved in pressure induced aggregation, whereas aggregates formed during heat treatments were primarily stabilized by hydrophobic interactions. The surface hydrophobicity of soluble protein increased by factor 2.5 to 4.5 after heat treatments and by factor 1.3 at maximum after pressure treatments. High pressure processing provides therefore a good alternative to conventional heat pasteurization as initial potato protein quality may be preserved to a higher extent. Foam stability was increased to 177% by pressure treatments, but this modification was not long-term stable. Applying high pressure with the aim of a functional modification therefore requires further investigations.     

Cross-linking proteins by laccase: Effects on the droplet size and rheology of emulsions stabilized by sodium caseinate

The aim of this work was to evaluate the influence of laccase and ferulic acid on the characteristics of oil-in-water emulsions stabilized by sodium caseinate at different pH (3, 5 and 7). Emulsions were prepared by high pressure homogenization of soybean oil with sodium caseinate solution containing varied concentrations of laccase (0, 1 and 5 mg/mL) and ferulic acid (5 and 10 mM). Laccase treatment and pH exerted a strong influence on the properties with a consequent effect on stability, structure and rheology of emulsions stabilized by Na-caseinate. At pH 7, O/W emulsions were kinetically stable due to the negative protein charge which enabled electrostatic repulsion between oil droplets resulting in an emulsion with small droplet size, low viscosity, pseudoplasticity and viscoelastic properties. The laccase treatment led to emulsions showing shear-thinning behavior as a result of a more structured system. O/W emulsions at pH 5 and 3 showed phase separation due to the proximity to protein pI, but the laccase treatment improved their stability of emulsions especially at pH 3. At pH 3, the addition of ferulic acid and laccase produced emulsions with larger droplet size but with narrower droplet size distribution, increased viscosity, pseudoplasticity and viscoelastic properties (gel-like behavior). Comparing laccase treatments, the combined addition of laccase and ferulic acid generally produced emulsions with lower stability (pH 5), larger droplet size (pH 3, 5 and 7) and higher pseudoplasticity (pH 5 and 7) than emulsion with only ferulic acid. The results suggested that the cross-linking of proteins by laccase and ferulic acid improved protein emulsifying properties by changing functional mechanisms of the protein on emulsion structure and rheology, showing that sodium caseinate can be successfully used in acid products when treated with laccase.     

High pressure treatment on the tofu fatty acids and acylglycerols content

Three batches of tofu were purchased from the local market. The samples were packaged under vacuum, and half of them subjected to a pressure in a range of 100 to 350 MPa at ambient temperature (22 °C) for 15 min, the rest were considered as control. The soy fat was extracted with hexane and the characterisation of fatty acids composition as methyl esters (FAME) and their diacyl–triacylglycerols (DAG, TAG) were analysed by Gas chromatography (GC). The tofu fat is low in saturated fatty acids (SFA, ∼ 16%) and high in polyunsaturated fatty acids (PUFA, ∼ 64%). The DAG content was lower than 10% and the highest value obtained for TAG was for the CN54 (∼ 60%), followed for the CN52 (∼ 28%) and CN50 (∼ 4%). No significant changes on the profile fat pattern have been found after the high pressure treatment in the assayed conditions. The ratios of PUFA/SFA and n-6/n-3 are 4 and 7 respectively. Tofu can be subjected to HP of 350 MPa without significant changes in its fat pattern.Industrial relevanceTofu is becoming an increasingly important international product outside its traditional markets. The use of high pressure processing for preservation purposes is a potential to retain or increase the nutritional value of foods of high relevance. This paper concentrates on the impact of high pressure on polyunsaturated acid and di-triacylglycerols. Interestingly no significant changes due to high pressure treatment could be observed marking this an attractive processing option.     

Manufacture of Cheddar cheese from high-pressure-treated whole milk

The cheese-making characteristics of high-pressure (HP)-treated milk were examined. The rennet coagulation time of pasteurised milk decreased after HP treatment at 400 MPa but increased after treatment at 600 MPa. The L-value (whiteness) of milk decreased directly after HP treatment but, over the course of coagulation, whiteness of HP-treated milk increased to the same level as in the control. Cheddar cheese was then manufactured from raw whole milk or whole milk treated by high-pressure (HP) at 400 MPa (HP400) or 600 MPa (HP600) for 10 min at 20 °C. HP treatment of raw milk at 600 MPa resulted in a 3.66 log reduction in the initial counts of non-starter lactic acid bacteria (NSLAB), decreased protein and fat content, as well as a lower pH compared to the control. Furthermore, higher treatment pressures resulted in increased incorporation of β-lactoglobulin into the cheese curd, with parallel increases in yield by 1.23% and 7.78% for HP400 and HP600 cheeses, respectively. Overall, this study showed that the effects of HP treatment on milk proteins increased rennet coagulation times and changes in cheese composition at day 1.Industrial relevanceHigh-pressure treatment is a novel technology which has been applied to a number of commercial food products. In this study, HP-induced changes in milk proteins resulted in increased cheese yields and increased cheese whiteness. In addition, HP treatment significantly reduced the microflora of raw milk cheese. Those attributes could be of interest for both industry and consumer.     

Effect of thermal and high hydrostatic pressure processing on antioxidant activity and colour of fruit smoothies

Fruit smoothie samples were thermally treated (P₇₀ ≥ 10 min) or high hydrostatic pressure (HHP) processed (450 MPa) with holding time of 1, 3 or 5 min and antioxidant activity, phenolic content and colour values (L*, a* and colour intensity) were determined. Significant reductions in antioxidant activity (p < 0.001) and phenolic content (p < 0.001) were observed at the applied pressure and a maximum treatment time of 5 min. Mean values for redness (a*) showed an increase (p < 0.001) in HHP processed smoothies compared to fresh. As expected, storage also had a significant effect on colour variables but the effect was more pronounced in high pressure treated samples stored for 30 days. Both colour and antioxidant activity were significantly affected by high pressure processing. Therefore, process optimisation of high pressure systems should be considered by processors prior to its adoption as a preservation technique in order to minimise the effect on the quality of fruit smoothie products.Industrial relevanceFruit smoothies have become popular with consumers and may significantly contribute to daily antioxidant intakes. Thermal processing has been shown to reduce the antioxidant activity of fruits, thus non-thermal methods of pasteurisation such as high hydrostatic pressure processing could help retain antioxidants in fruit smoothies offering a unique selling point for processors. The present study focussed on assessing the effect of thermal and high pressure processing on the antioxidant activity and phenolic content of fruit smoothies. Since decreases in levels of antioxidants were noted during long term storage it would appear that higher pressure treatments (> 450 MPa) might be required for better retention of antioxidant compounds in fruit smoothies.     

Effects of high hydrostatic pressure on the quality and shelf-life of jujube (Ziziphus jujuba Mill.) pulp

This study evaluated the effects of high hydrostatic pressure (HHP) on the microbial counts, physicochemical properties, bioactive compounds, and antioxidant capacity of jujube pulp. Additionally, this study compared the shelf life of jujube pulp following HHP (600 MPa/20 min) and thermal treatment (100 °C/10 min) during 40 days of storage at 4 °C and 15 °C. The microbial count of HHP-treated jujube pulp (≥ 400 MPa/20 min) was below the detection limit. Total soluble solids and total sugars were not significantly affected by HHP processing, and > 90% ascorbic acid was retained in HHP-treated samples. HHP slightly reduced pH and browning degree and increased total phenolic content, flavonoid content, and antioxidant capacity. HHP can be used as an alternative to thermal pasteurization of freshly squeezed jujube pulp.Industrial relevanceEffects of high hydrostatic pressure (HHP) processing and thermal treatment (TT) on microbiological quality, physicochemical properties, bioactive compounds and antioxidant activity in jujube pulp were investigated. Greater inhibition of microorganisms and better retention of ascorbic acid, total phenolics, flavonoid and antioxidant capacity were observed after HHP-treatment. The available data could be used to design the HHP parameters for high quality jujube juice. Further, this research would provide a useful method for preservation of jujube products and potential technical support for jujube commercial production.     

Antioxidant capacity,phenolic composition and microbial stability of aronia juice subjected to high hydrostatic pressure processing

The aim of this study was to characterize the effect of high hydrostatic pressure (200–600 MPa/15 min) and storage (4 °C/80 days) on aronia juice quality. The total antioxidant capacity, phenolic content and composition were assessed using an updated analytical strategy. Microbial growth was also analyzed following juice storage. Among all the analyzed juices, the untreated aronia juice had the greatest reduction (36%) in total polyphenols over the entire storage period. At the end of the storage period, the pressurized juices demonstrated ABTS and FRAP values higher by 14% and 5% as compared to the untreated juices. The main antioxidants identified in the aronia juice were: chlorogenic acid; neochlorogenic acid; cyanidin 3-galactoside; cyanidin 3-xyloside; cyanidin 3-arabinoside; cyanidin 3-glucoside. Cyanidin 3-glucoside was the most stable compound during juice storage. Microorganism growth in juices pressurized at 400–600 MPa was below the detection limit (< 1 CFU mL^− 1) upon storage.Industrial relevanceAronia berries are rarely consumed fresh since they give off several negative sensory attributes. Multiple health-promoting properties of aronia berries make them a valuable raw material for juice production. However, processing involves pasteurization or hot-filling strongly diminishes the product quality due to the changes in quantity and quality of thermolabile phytochemicals. The objective of this work was to characterize the effect of high hydrostatic pressure on the antioxidant capacity, polyphenol content and composition and microbial stability of aronia juice. Results of this study may be useful for the juice industry commercialize this technology for the development healthy, nonclarified aronia juices with desired level of quality.     

Kinetics of destruction ofEscherichia coliandPseudomonas fluorescensinoculated in ewe's milk by high hydrostatic pressure

Ewe's1999199919991999 Academic PressAcademic PressAcademic PressAcademic Pressmilk standardized to 6% fat was inoculated with Escherichia coliand Pseudomonas fluorescensat a concentration of 10⁷and 10⁸ cfu ml⁻¹respectively, and treated by high hydrostatic pressure. Treatments consisted of combinations of pressure (50-300 MPa), temperature (2, 10, 25 and 50°C), and time (5, 10 and 15 min). Violet red bile agar and crystal-violet-tetrazolium count were used to determineE. coliandP. fluorescensrespectively. Pressurization at low and moderately high temperatures produced higher P. fluorescensinactivation than treatments at room temperature, while pressurization at only moderately high temperature produced high E. coliinactivation; low and room temperatures produced similar reductions. On E. coli,reductions of 6.055 log units were produced with 300 MPa for 15 min at 50°C, while on P. fluorescens,reductions of 5.059 log units were produced with 250 MPa for 15 min at 50°C. Both micro-organisms showed a first-order kinetics of destruction in the range 0-30 min, with D-values (at different temperatures and pressures from 150 to 300 MPa) between 2.055 and 18.058 min for E. coli,and 2.058-23.053 min for P. fluorescens.Abaroprotective effect of ewe's milk (6% fat) on both micro-organisms was observed, in comparison with other studies using different means and similar pressurization conditions.