Transparent, highly flexible, all nanowire network germanium photodetectors

We report on the fabrication and characterization of all nanowire (NW) network photodetectors. For this purpose, germanium (Ge) NW networks are used as active semiconducting elements, whereas single walled carbon nanotube (SWNT) and silver (Ag) NW networks are used as the contacts. Following their synthesis, all NW networks are deposited through simple solution based methods. Photoresponse characteristics and transparency of the photodetectors for different Ge NW densities are measured. The fabricated devices show a large response with short relaxation times (<10 ms), are flexible and transparent within the visible spectrum.     

Flexible Transparent Films Based on Nanocomposite Networks of Polyaniline and Carbon Nanotubes for High‐Performance Gas Sensing

A flexible, transparent, chemical gas sensor is assembled from a transparent conducting film of carbon nanotube (CNT) networks that are coated with hierarchically nanostructured polyaniline (PANI) nanorods. The nanocomposite film is synthesized by in‐situ, chemical oxidative polymerization of aniline in a functional multiwalled CNT (FMWCNT) suspension and is simultaneously deposited onto a flexible polyethylene terephthalate (PET) substrate. An as‐prepared flexible transparent chemical gas sensor exhibits excellent transparency of 85.0% at 550 nm using the PANI/FMWCNT nanocomposite film prepared over a reaction time of 8 h. The sensor also shows good flexibility, without any obvious decrease in performance after 500 bending/extending cycles, demonstrating high‐performance, portable gas sensing at room temperature. This superior performance could be attributed to the improved electron transport and collection due to the CNTs, resulting in reliable and efficient sensing, as well as the high surface‐to‐volume ratio of the hierarchically nanostructured composites. The excellent transparency, improved sensing performance, and superior flexibility of the device, may enable the integration of this simple, low‐cost, gas sensor into handheld flexible transparent electronic circuitry and optoelectronic devices.     

Flexible and Transparent Gas Molecule Sensor Integrated with Sensing and Heating Graphene Layers

Graphene leading to high surface‐to‐volume ratio and outstanding conductivity is applied for gas molecule sensing with fully utilizing its unique transparent and flexible functionalities which cannot be expected from solid‐state gas sensors. In order to attain a fast response and rapid recovering time, the flexible sensors also require integrated flexible and transparent heaters. Here, large‐scale flexible and transparent gas molecule sensor devices, integrated with a graphene sensing channel and a graphene transparent heater for fast recovering operation, are demonstrated. This combined all‐graphene device structure enables an overall device optical transmittance that exceeds 90% and reliable sensing performance with a bending strain of less than 1.4%. In particular, it is possible to classify the fast (≈14 s) and slow (≈95 s) response due to sp²‐carbon bonding and disorders on graphene and the self‐integrated graphene heater leads to the rapid recovery (≈11 s) of a 2 cm × 2 cm sized sensor with reproducible sensing cycles, including full recovery steps without significant signal degradation under exposure to NO₂ gas.     

Stretchable Electronic Sensors of Nanocomposite Network Films for Ultrasensitive Chemical Vapor Sensing

A stretchable, transparent, and body‐attachable chemical sensor is assembled from the stretchable nanocomposite network film for ultrasensitive chemical vapor sensing. The stretchable nanocomposite network film is fabricated by in situ preparation of polyaniline/MoS₂ (PANI/MoS₂) nanocomposite in MoS₂ suspension and simultaneously nanocomposite deposition onto prestrain elastomeric polydimethylsiloxane substrate. The assembled stretchable electronic sensor demonstrates ultrasensitive sensing performance as low as 50 ppb, robust sensing stability, and reliable stretchability for high‐performance chemical vapor sensing. The ultrasensitive sensing performance of the stretchable electronic sensors could be ascribed to the synergistic sensing advantages of MoS₂ and PANI, higher specific surface area, the reliable sensing channels of interconnected network, and the effectively exposed sensing materials. It is expected to hold great promise for assembling various flexible stretchable chemical vapor sensors with ultrasensitive sensing performance, superior sensing stability, reliable stretchability, and robust portability to be potentially integrated into wearable electronics for real‐time monitoring of environment safety and human healthcare.     

Healable,Transparent, Room‐Temperature Electronic Sensors Based on Carbon Nanotube Network‐Coated Polyelectrolyte Multilayers

Transparent and conductive film based electronics have attracted substantial research interest in various wearable and integrated display devices in recent years. The breakdown of transparent electronics prompts the development of transparent electronics integrated with healability. A healable transparent chemical gas sensor device is assembled from layer‐by‐layer‐assembled transparent healable polyelectrolyte multilayer films by developing effective methods to cast transparent carbon nanotube (CNT) networks on healable substrates. The healable CNT network‐containing film with transparency and superior network structures on self‐healing substrate is obtained by the lateral movement of the underlying self‐healing layer to bring the separated areas of the CNT layer back into contact. The as‐prepared healable transparent film is assembled into healable transparent chemical gas sensor device for flexible, healable gas sensing at room temperature, due to the 1D confined network structure, relatively high carrier mobility, and large surface‐to‐volume ratio. The healable transparent chemical gas sensor demonstrates excellent sensing performance, robust healability, reliable flexibility, and good transparency, providing promising opportunities for developing flexible, healable transparent optoelectronic devices with the reduced raw material consumption, decreased maintenance costs, improved lifetime, and robust functional reliability.     

Ink-jet printed transparent and flexible electrodes based on silver nanoparticles

In recent, silver (Ag) nanowires (NWs) have received much attention as an alternative to indium tin oxide (ITO) for transparent electrode application in printed and transparent electronics. However, Ag NWs have its breakup problem by joule heating during current. To overcome this problem, this paper demonstrates a mesh type electrode based on Ag nanoparticles, which is fabricated on PET substrate through an ink-jet printing technique. The proposed electrode has a low resistance of 108.5 Ω/sq and a good optical transparency around 92% at 300–800 nm. It has a relationship that the sheet resistance drops with the decrease of transparency due to depending hole size and the best curing temperature is found to be 120 °C. It also demonstrate an excellent flexible stability, showing <?2% resistance change after over 100 bending cycles. These resistance and transparency are similar with that of commercially ITO electrode, and are superior to other alternatives such as carbon nanotube electrodes. The proposed electrode can be considered as a commercial electrode to as an alternative to ITO electrode.     

A Self‐Powered and Flexible Organometallic Halide Perovskite Photodetector with Very High Detectivity

Flexible and self‐powered photodetectors (PDs) are highly desirable for applications in image sensing, smart building, and optical communications. In this paper, a self‐powered and flexible PD based on the methylammonium lead iodide (CH₃NH₃PBI₃) perovskite is demonstrated. Such a self‐powered PD can operate even with irregular motion such as human finger tapping, which enables it to work without a bulky external power source. In addition, with high‐quality CH₃NH₃PBI₃ perovskite thin film fabricated with solvent engineering, the PD exhibits an impressive detectivity of 1.22 × 10¹³ Jones. In the self‐powered voltage detection mode, it achieves a large responsivity of up to 79.4 V mW^?1 cm^?2 and a voltage response of up to ≈90%. Moreover, as the PD is made of flexible and transparent polymer films, it can operate under bending and functions at 360 ° of illumination. As a result, the self‐powered, flexible, 360 ° omnidirectional perovskite PD, featuring high detectivity and responsivity along with real‐world sensing capability, suggests a new direction for next‐generation optical communications, sensing, and imaging applications.     

Junction‐Free Electrospun Ag Fiber Electrodes for Flexible Organic Light‐Emitting Diodes

Fabrication of junction‐free Ag fiber electrodes for flexible organic light‐emitting diodes (OLEDs) is demonstrated. The junction‐free Ag fiber electrodes are fabricated by electrospun polymer fibers used as an etch mask and wet etching of Ag thin film. This process facilitates surface roughness control, which is important in transparent electrodes based on metal wires to prevent electrical instability of the OLEDs. The transmittance and resistance of Ag fiber electrodes can be independently adjusted by controlling spinning time and Ag deposition thickness. The Ag fiber electrode shows a transmittance of 91.8% (at 550 nm) at a sheet resistance of 22.3 Ω □^?1, leading to the highest OLED efficiency. In addition, Ag fiber electrodes exhibit excellent mechanical durability, as shown by measuring the change in resistance under repeatable mechanical bending and various bending radii. The OLEDs with Ag fiber electrodes on a flexible substrate are successfully fabricated, and the OLEDs show an enhancement of EQE (≈19%) compared to commercial indium tin oxide electrodes.     

Reverse‐Offset Printed Ultrathin Ag Mesh for Robust Conformal Transparent Electrodes for High‐Performance Organic Photovoltaics

Mechanically durable transparent electrodes are needed in flexible optoelectronic devices to realize their long‐term stable functioning, for applications in various fields such as energy, healthcare, and soft robotics. Several promising transparent electrodes based on nanomaterials have been previously reported to replace the conventional and fragile indium‐tin oxide (ITO); however, obtaining feasible printed transparent electrodes for ultraflexible devices with a multistack structure is still a great challenge. Here, a printed ultrathin (uniform thickness of 100 nm) Ag mesh transparent electrode is demonstrated, simultaneously achieving high conductance, high transparency, and good mechanical properties. It shows a 17 Ω sq^?1 sheet resistance (R_sh) with 93.2% transmittance, which surpasses the performance of sputtered ITO electrodes and other ultrathin Ag mesh transparent electrodes. The conductance is stable after 500 cycles of 100% stretch/release deformation, with an insignificant increase (10.6%) in R_sh by adopting a buckling structure. Furthermore, organic photovoltaics (OPVs) using our Ag mesh transparent electrodes achieve a power conversion efficiency of 8.3%, which is comparable to the performance of ITO‐based OPVs.     

An Optically Flat Conductive Outcoupler Using Core/Shell Ag/ZnO Nanochurros

Transparent conductive electrodes (TCEs) featuring a smooth surface are indispensable for preserving pristine electrical characteristics in optoelectronic and transparent electronic devices. For high‐efficiency organic light emitting diodes (OLEDs), a high outcoupling efficiency, which is crucial, is only achieved by incorporating a wavelength‐scale undulating surface into a TCE layer, but this inevitably degrades device performance. Here, an optically flat, high‐conductivity TCE composed of core/shell Ag/ZnO nanochurros (NCs) is reported embedded within a resin film on a polyethylene terephthalate substrate, simultaneously serving as an efficient outcoupler and a flexible substrate. The ZnO NCs are epitaxially grown on the {100} planes of a pentagonal Ag core and the length of ZnO shells is precisely controlled by the exposure time of Xe lamp. Unlike Ag nanowires films, the Ag/ZnO NCs films markedly boost the optical tunneling of light. Green‐emitting OLEDs (2.78 × 3.5 mm²) fabricated with the Ag/ZnO TCE exhibit an 86% higher power efficiency at 1000 cd m^?2 than ones with an Sn‐doped indium oxide TCE. A full‐vectorial electromagnetic simulation suggests the suppression of plasmonic absorption losses within their Ag cores. These results provide a feasibility of multifunctional TCEs with synthetically controlled core/shell nanomaterials toward the development of high‐efficiency LED and solar cell devices.     

Pressure Welding of Silver Nanowires Networks at Room Temperature as Transparent Electrodes for Efficient Organic Light‐Emitting Diodes

In this work, polymethylmethacrylate (PMMA) as a superior mediate for the pressure welding of silver nanowires (Ag NWs) networks as transparent electrodes without any thermal treatment is demonstrated. After a pressing of 200 kg cm^?2, not only the sheet resistance but also the surface roughness of the PMMA‐mediated Ag NWs networks decreases from 2.6 kΩ sq^?1 to 34.3 Ω sq^?1 and from 76.1 to 12.6 nm, respectively. On the other hand, high transparency of an average transmittance in the visible wavelengths of 93.5% together with a low haze value of 2.58% can be achieved. In terms of optoelectronic applications, the promising potential of the PMMA‐mediated pressure‐welded Ag NWs networks used as a transparent electrode in a green organic light‐emitting diode (OLED) device is also demonstrated. In comparison with the OLED based on commercial tin‐doped indium oxide electrode, the increments of power efficiency and external quantum efficiency (EQE) from 80.1 to 85.9 lm w^?1 and 19.2% to 19.9% are demonstrated. In addition, the PMMA‐mediated pressure welding succeeds in transferring Ag NWs networks to flexible polyethylene naphthalate and polyimide substrates with the sheet resistance of 42 and 91 Ω sq^?1 after 10 000 times of bending, respectively.     

Flexible,Semitransparent, and Inorganic Resistive Memory based on BaTi0.95Co0.05O3 Film

Perovskite ceramics and single crystals are commonly hard and brittle due to their small maximum elastic strain. Here, large‐scale BaTi_0.95Co_0.05O₃ (BTCO) film with a SrRuO₃ (SRO) buffered layer on a 10 µm thick mica substrate is flexible with a small bending radius of 1.4 mm and semitransparent for visible light at wavelengths of 500–800 nm. Mica/SRO/BTCO/Au cells show bipolar resistive switching and the high/low resistance ratio is up to 50. The resistive‐switching properties show no obvious changes after the 2.2 mm radius memory being written/erased for 360 000 cycles nor after the memory being bent to 3 mm radius for 10 000 times. Most importantly, the memory works properly at 25–180 °C or after being annealed at 500 °C. The flexible and transparent oxide resistive memory has good prospects for application in smart wearable devices and flexible display screens.     

Highly flexible transparent film heaters based on random networks of silver nanowires

We demonstrate a new concept for the fabrication of flexible transparent thin film heaters based on silver nanowires. Thanks to the intrinsic properties of random networks of metallic nanowires, it is possible to combine bendability, transparency and high heating performances at low voltage, typically below 12 V which is of interest for many applications. This is currently not possible with transparent conductive oxide technologies, and it compares well with similar devices fabricated with carbon nanotubes or graphene. We present experiments on glass and poly(ethylene naphthalate) (PEN) substrates (with thicknesses of 125 μm and extremely thin 1.3 μm) with excellent heating performances. We point out that the amount of silver necessary to realize the transparent heaters is very low and we also present preliminary results showing that this material can be efficiently used to fabricate photochromic displays. To our knowledge, this is the first report of metallic nanowire-based transparent thin film heaters. We think these results could be a useful approach for the engineering of highly flexible and transparent heaters which are not attainable by existing processes.      

Flexible Transparent Conductive Films on the Basis of Ag Nanowires:Design and Applications:A Review

Transparent conductive films are used ubiquitously in optoelectronic devices.The properties of transparent films are extremely important for device performance,and the specifications vary according to types of devices.Over the past few years,various types of transparent conductive films on the basis of nanomaterials have emerged,and among these materials,silver nanowire networks show promising performance and represent a viable alternative to the commonly used,scarce and brittle indium tin oxide.In this paper,the working principle and the design protocol of Ag nanowire network flexible transparent conductive films are reviewed,and the applications of Ag nanowircs transparent conductive film are also briefly introduced.Concluding remarks are provided to propose future research in this field towards real-world applications.     

Thermal Response of Transparent Silver Nanowire/PEDOT:PSS Film Heaters

Thermal response behavior of transparent silver nanowire/PEDOT:PSS film heaters are intensively studied for manipulating heating temperature, response time, and power consumption. Influences of substrate heat capacity, heat transfer coefficient between air and heater, sheet resistance and dimension of Ag nanowire film, on the thermal response are investigated from thermodynamic analysis. Suggestion is given for practical applications that if other parameters are fixed, Ag nanowire coverage can be utilized as an effective parameter to adjust the thermal response. The heat transfer coefficient plays opposite roles on thermal response speed and achievable steady temperature. A value of ≈32 W m^?2 K^?1 is obtained from transient process analysis after correcting it by considering heater resistance variation during heating tests. Guidance of designing heaters with a given response time is provided by forming Ag nanowire film with a suitable sheet resistance on substrate of appropriate material and a certain thickness. Thermal response tests of designed Ag heaters are performed to show higher heating temperature, shorter response time, and lower power consumption (179 °C cm² W^?1) than ITO/FTO heaters, as well as homogeneous temperature distribution and stability for repeated use. Potential applications of the Ag heaters in window defogging, sensing and thermochromism are manifested.     

Density-controllable growth of SnO2 nanowire junction-bridging across electrode for low-temperature NO2 gas detection

The junction-bridging structure of metal oxide nanowires (NWs) improves gas-sensing properties. In this study, an on-chip growth method was used to fabricate gas sensors, it easily and effectively controls NW junctions. SnO₂ NWs were synthesized by thermal evaporation at 800 °C with tin powder as the source. The density of the NW junctions was controlled by changing the mass of the source material. A source material with large mass yielded high-density NW junctions. With electrode spacing of 20 μm, NW junctions were formed from the source material of larger than 2 mg. Gas sensing results revealed that the junction sensors exhibited a good response to NO₂ gas at a concentration of 1–10 ppm. The sensors exhibited a good response to NO₂ gas at low temperature of up to 100 °C and short response–recovery time (~20 s). The sensors also had good selectivity to NO₂ gas. The response (R _gas /R _air) to 1 ppm NO₂ was as high as 22 at 100 °C, whereas the cross gas responses (R _air /R _gas) to 10 ppm CO, 10 ppm H₂S, 100 ppm C₂H₅OH, and 100 ppm NH₃ were negligible (1.1–1.3).     

UV–Ozone Interfacial Modification in Organic Transistors for High‐Sensitivity NO2 Detection

A new type of nitrogen dioxide (NO₂) gas sensor based on copper phthalocyanine (CuPc) thin film transistors (TFTs) with a simple, low‐cost UV–ozone (UVO)‐treated polymeric gate dielectric is reported here. The NO₂ sensitivity of these TFTs with the dielectric surface UVO treatment is ≈400× greater for [NO₂] = 30 ppm than for those without UVO treatment. Importantly, the sensitivity is ≈50× greater for [NO₂] = 1 ppm with the UVO‐treated TFTs, and a limit of detection of ≈400 ppb is achieved with this sensing platform. The morphology, microstructure, and chemical composition of the gate dielectric and CuPc films are analyzed by atomic force microscopy, grazing incident X‐ray diffraction, X‐ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy, revealing that the enhanced sensing performance originates from UVO‐derived hydroxylated species on the dielectric surface and not from chemical reactions between NO₂ and the dielectric/semiconductor components. This work demonstrates that dielectric/semiconductor interface engineering is essential for readily manufacturable high‐performance TFT‐based gas sensors.     

Flexible Metal–Organic Framework‐Based Mixed‐Matrix Membranes: A New Platform for H2S Sensors

Metal–organic framework (MOF)–polymer mixed‐matrix membranes (MMMs) have shown great potential and superior performance in gas separations. However, their sensing application has not been fully established yet. Herein, a rare example of using flexible MOF‐based MMMs as a fluorescent turn‐on sensor for the detection of hydrogen sulfide (H₂S) is reported. These MOF‐based MMMs are readily prepared by mixing a highly stable aluminum‐based nano‐MOF (Al‐MIL‐53‐NO₂) into poly(vinylidene fluoride) with high loadings up to 70%. Unlike the intrinsic fragility and poor processability of pure‐MOF membranes, these MMMs exhibit desirable flexibility and processability that are more suitable for practical sensing applications. The uniform distribution of Al‐MIL‐53‐NO₂ particles combined with the permanent pores of MOFs enable these MMMs to show good water permeation flux and consequently have a full contact between the analyte and MOFs. The developed MMM sensor (70% MOF loading) thus shows a highly remarkable detection selectivity and sensitivity for H₂S with an exceptionally low detection limit around 92.31 × 10^?9m , three orders of magnitude lower than the reported powder‐form MOFs. This work demonstrates that it is feasible to develop flexible luminescent MOF‐based MMMs as a novel platform for chemical sensing applications.     

Ag@Ni Core–Shell Nanowire Network for Robust Transparent Electrodes Against Oxidation and Sulfurization

Silver nanowire (Ag NW) based transparent electrodes are inherently unstable to moist and chemically reactive environment. A remarkable stability improvement of the Ag NW network film against oxidizing and sulfurizing environment by local electrodeposition of Ni along Ag NWs is reported. The optical transmittance and electrical resistance of the Ni deposited Ag NW network film can be easily controlled by adjusting the morphology and thickness of the Ni shell layer. The electrical conductivity of the Ag NW network film is increased by the Ni coating via welding between Ag NWs as well as additional conductive area for the electron transport by electrodeposited Ni layer. Moreover, the chemical resistance of Ag NWs against oxidation and sulfurization can be dramatically enhanced by the Ni shell layer electrodeposited along the Ag NWs, which provides the physical barrier against chemical reaction and diffusion as well as the cathodic protection from galvanic corrosion.     

Robust and Aligned Carbon Nanotube/Titania Core/Shell Films for Flexible TCO‐Free Photoelectrodes

Carbon nanotube (CNT)/semiconducting oxide hybrids are an ideal architecture for light‐harvesting devices, in which the CNTs are expected to not only act as a scaffold but also provide fast transport paths for photogenerated charges in the oxide. However, the current potential of CNTs for charge transport is largely suppressed due to the nanotubes not being interconnected but isolated by the low conductive oxide coatings. Herein, a flexible and conductive CNT/TiO₂ core/shell heterostructure film is reported, with aligned and interconnected CNTs wrapped in a continuous TiO₂ coating. Without using additional transparent conducting oxide (TCO) substrates, this unique feature of the film boosts the incident photon‐to‐electron conversion efficiency to 32%, outperforming TiO₂ nanoparticle electrodes fabricated on TCO substrates. Moreover, the film shows high structural stability and can generate a stable photocurrent even after being bent hundreds of times.