变动电流作用下焊接熔池谐振现象的研究

本文在固定点 TIG 焊接电弧下,利用在直流焊接电流上叠加正弦波电流的方法,通过计算机对电弧电压变化量采样处理,对薄钢板焊接熔池在变动电流作用下产生的谐振现象做了初步实验研究,结果表明,熔池金属谐振频率与熔池尺寸之间有严格对应关系,利用此方法可以一定程度地解决薄钢板焊接熔透控制问题。     

窄间隙P-GMAW多信息融合侧壁熔合状态识别研究

窄间隙焊缝坡口间距小且焊道较深,摆动中心与焊缝中心偏差较大时,坡口两侧侧壁受热不良,易发生未熔合缺陷。为了及时了解窄间隙侧壁熔合情况,掌握侧壁内部焊接质量,本文提出了一种基于BP神经网络和D-S证据理论的多信息融合方法,预测侧壁熔合状态。对窄间隙焊接未熔合缺陷产生机制进行了分析,研究发现焊接电弧信号和熔池变化与侧壁成形质量存在密切关系,为此进行了一系列偏差实验,建立了电弧电信号和电弧熔池图像信号的实时采集系统,采用批量特征提取算法,提取了与侧壁熔合状态密切关联的峰值电流、峰值电压、电弧弧长、熔池长宽比、熔池面积和熔池周长等特征参量。采用BP算法训练神经网络,在此基础上通过D-S证据理论进行决策级融合。实验结果表明,该模型识别率可达96.667%,避免了神经网络识别时的误诊,获得了比单一传感信息更好的预测结果,提高了熔合状态识别的准确度和可靠度。     

变极性等离子弧穿孔熔池受力及焊缝成形稳定性

通过YB005-01型压力变送器测定相同参数条件下正极性等离子电弧力大于反极性等离子电弧力,并建立了铝合金VPPA焊接穿孔熔池受力模型,分析了在不对称正、反极性等离子电弧力的作用下,穿孔溶池稳定性及其焊缝成形机理.同时进一步分析铝合金VPPA力学特性,掌握了焊接电流和离子气流量等重要焊接参数对其影响.经穿孔焊工艺实验,...     

粉末熔池耦合活性TIG焊接方法

提出了一种新型活性焊接方法——粉末熔池耦合活性TIG焊(Powder pool coupled activating TIG welding,PPCATIG)。该方法采用双层气体进行焊接,内层利用惰性气体保护钨极,外层通过自动送粉装置将活性剂粉末随保护气体送入电弧-熔池区域,增加熔深,提高焊接效率,实现机械化自动化焊接。针对SUS304不锈钢进行了直流正接PPCA-TIG表面熔深,通过与传统TIG焊对比,研究了SiO_2活性剂对电弧形态、焊缝成形、组织和力学性能的影响。结果表明:SiO_2能使电弧等离子体收缩、熔池金属流态改变,并且焊缝熔深能达到传统TIG焊的3倍以上,焊接效率明显提高。焊缝组织主要为奥氏体和铁素体,铁素体形态以骨架状为主。焊缝抗拉强度略低于母材,但相比传统TIG焊,焊缝屈服强度略有提高,其焊缝低温冲击韧性达到了传统TIG焊的96.8%,表现出了良好的力学性能。同时,采用该方法可有效避免活性剂粉末对钨极的污染。     

等离子弧焊接熔池和小孔形成过程数值分析

目的 研究等离子弧焊接穿孔过程中熔池内部的金属流动情况和小孔动态变化过程。方法 通过“传热-熔池流动-小孔”之间的相互耦合关系,建立了等离子弧焊接穿孔过程的数值分析模型,通过VOF方法追踪了小孔界面,采用FLOW-3D软件模拟了等离子弧焊接熔池和小孔的形成过程,定量计算了等离子弧焊接温度场、熔池流场及小孔形状;分析了等离子弧焊接熔池和小孔行为;并通过等离子弧焊接实验数据验证了模拟结果。结果 当焊接时间为0~1.0 s时,小孔深度曲线与熔深曲线几乎相同,小孔底部紧贴熔池底部;在2.8 s以后,小孔深度曲线与熔深曲线有一定距离,小孔深度曲线在一定范围内波动,等离子弧焊接电弧挖掘作用到达极限,电弧压力与其他力达到平衡状态。模拟的焊缝熔深为8.04 mm、熔宽为13.20 mm,实验测得的焊缝熔深为8.00 mm、熔宽为13.42 mm。结论 构建的随小孔动态变化的曲面热源模型和电弧压力模型可以描述等离子弧焊接过程中的电弧热-力分布;模拟出了等离子弧焊接熔池和小孔动态演变过程;模拟得到的等离子弧焊接焊缝形貌与实验测得的焊缝形貌基本吻合。     

焊剂片约束电弧焊接三明治板熔滴过渡与熔池波动研究

针对焊剂片约束电弧(FBCA)焊接高强钢三明治板熔池研究难点,采用侧边贴敷耐高温石英玻璃片方法,采集焊接动态过程信息,实现熔池边缘曲线的提取与特征参数的计算,研究不同参数下熔滴过渡模式及熔池边缘曲线波动情况,分析熔池振荡角与焊接稳定性及焊缝成形之间的关系。结果表明：不同参数下FBCA焊接存在短路过渡、粗滴过渡、排斥过渡、细滴过渡、射滴过渡、弧桥并存过渡六种过渡方式,对芯板内熔池边缘波动的影响依次减弱;随着熔池振荡角变化,熔池边缘曲线形状存在混合U形、深U形及浅U形,电弧燃烧稳定性依次增强;当焊接处于弧桥并存过渡模式、熔池边缘曲线为浅U形时,电弧稳定燃烧,电弧力作用均匀,焊接过程稳定,焊缝质量最好。     

CLAM钢穿孔等离子超声电弧焊接激励频率的优化

为了优化超声电弧焊接激励频率,针对穿孔等离子超声电弧焊接熔池进行了计算机模态分析.根据穿孔等离子弧焊接特点,利用特定的数值分析模型,通过ANSYS软件计算超声电弧焊接熔池模态,分析与模态频率相对应的熔池响应情况.最后,分别施加不同大小的超声电弧频率,以3组4.5 mm厚的中国低活化马氏体(CLAM)钢板为实验材料进行平板对接焊试验.结果表明:在谐振条件下,焊缝区面积增大,组织的细化效果较好,界面棒状碳化物生长得到抑制,同时焊缝区硬化现象得到显著改善;利用这种方法基本达到了超声电弧频率优化的目的.     

双电极奥氏体不锈钢焊条单弧焊工艺研究

本文研究了双电极奥氏体不锈钢焊条单弧焊电弧的静特性、焊接电流、电弧电压、焊芯间隙对双电极焊条单弧焊的工艺性能和焊缝成形的影响;通过热电偶测试技术,对双电极焊条单弧焊焊接过程中不同部位焊芯表面温升进行了测定.研究结果表明焊芯直径为φ4.0mm的双电极A102焊条,其合适焊接工艺参数为:焊接电流140～160A,电弧电压45V左右,焊条两芯间隙1.2～1.5mm,焊接板厚8mm的1Cr18Ni9Ti材料,焊缝成形良好.     

激光-电弧复合焊热源相对位置对焊接接头组织与性能影响规律研究

采用20 mm厚EH36钢板堆焊试验研究了激光-电弧复合焊热源相对位置对焊缝宏观形貌、组织、元素烧损和性能的影响规律。结果表明,与电弧引导激光焊接相比,激光引导电弧焊接的焊缝熔深小、熔宽大、熔合比小、焊道对称性差、合金元素烧损率小、显微硬度相对较低;激光引导电弧焊接时,焊缝区晶粒向熔池表面中心生长、晶粒相对粗大,电弧引导激光焊接时,晶粒向着焊缝中心生长、晶粒相对细小,这主要是由于两种热源相对位置不同使得进入焊缝的总能量和熔池流动方向不同造成的。     

激光功率对激光-电弧复合横焊焊缝成形的影响

以10CrNiMoV钢为对象,借助焊缝成形参数评价激光-电弧复合横焊焊缝的成形特征,研究了激光功率对激光-电弧复合横焊焊缝成形的影响规律。结果表明,激光能显著增强焊接电弧稳定性;随着激光功率的增加,熔池液态金属的下淌程度呈现先降低、后激增的变化趋势。     

Control of submerged arc weld penetration by radiographic means

The application of real-time radiography for in-process weld quality evaluation is discussed. The advantages of this technique are on-line testing of weld penetration and the possibility of using this information for welding current control. The experimental system developed includes the arc welding unit, the welding manipulator, the real-time X-ray machine and the videorecording and computerized image processing units. In this system welding current can be remotely controlled during weld observation. The experimental results are demonstrated for the submerged arc welding process. In this process the welding pool is covered by a thick layer of welding flux and is therefore optically invisible. By using computer data on the grey levels of the weld images and their histogram distributions, the three-dimensional shape of the submerged arc pool can be recognized, image-digitized and analysed in real time at the rate of 30 frames per second. The depth of the welding pool which characterizes the weld penetration is a very important characteristic of the weld quality. This characteristic can be measured in real time and used for weld tracking and welding current control.     

30CrMnSiA熔池谐振法熔透控制TIG焊工艺及其接头组织的研究

本文采用电弧传感熔池谐振法研究了30CrMnSiA钢熔透控制TIG焊工艺,同时选取普通连续TIG焊进行了对比讨论,并对其效果进行了分析。试验结果证明,该控制方法在适当的工艺条件下,对30CrMnSiA钢可实现高可靠性的熔透控制,不仅能单面焊双面成形,且熔宽均匀无下塌,不需焊前预热和焊后缓冷。在较大热输入量条件下,接头仍能保持较好的组织与性能。     

TC4合金等离子–MIG复合焊过程温度场的数值模拟

目的 研究TC4合金在等离子-MIG复合焊(Plasma–MIG Hybrid Welding)过程中的温度场特性,探究不同电弧功率对熔池形貌的影响。方法 进行了2组4 mm TC4合金板堆焊试验,根据实验结果提出了一种改进的复合热源模型并进行了相应的仿真分析。结果 仿真与实验获得的焊缝截面相吻合;等离子电流的增大使熔池尺寸增大且余高减小,等离子电弧功率的变化对熔池宽度的影响相对较小。结论 等离子–MIG复合电弧对工件的热作用非常集中,更易实现深熔焊、焊接效率更高;所提出的热源模型适用于TC4合金等离子–MIG复合焊温度场模拟。     

基于机器学习的薄板等离子弧搭接焊的熔深预测

在等离子弧搭接焊中,搭接焊接头的焊缝熔深是评价焊接质量的关键指标之一,而焊接过程中的热输入信息和熔池图像信息都与焊缝熔深有密切关系。本文通过建立304L不锈钢薄板等离子弧搭接焊数据采集系统,利用LabVIEW实时检测电信息,采用视觉传感技术实时获取薄板等离子弧搭接焊过程中的熔池图像,并通过图像处理方法获得熔池的几何参数信息,结合焊接工艺参数,选择峰值电流、峰值电压、焊接速度、离子气流量、保护气流量、熔池宽度和熔池后端长度作为输入量,焊缝熔深作为输出量,建立了基于支持向量机回归和BP神经网络的熔深预测模型。实验验证表明,采用径向基函数的支持向量机回归模型可以有效地对焊缝熔深进行预测,并具有很好的泛化能力,可为进一步实现在线优化焊接工艺参数提供依据。     

Effect of controlled atmosphere on the mig-mag arc weldment properties

Due to their higher welding speed, automation and weld pool protection against to the atmosphere gases, gas metal arc welding (GMAW) process is widely used in industry. Due to the less stable arc associated with the use of consumable electrodes, GMAW process is not clean as good as gas tungsten arc welding process. Furthermore, the greater arc length in GMAW process also reduces the protective effect of the shielding gas. Due to electrochemical and thermochemical reactions between weld pool and arc atmosphere, it is quite important, especially weld metal toughness and joining of reactive materials to entirely create inert atmosphere for GMAW process. Therefore, a controlled atmosphere cabinet was developed for GMAW process. Low carbon steel combinations were welded with classical GMAW process in argon atmosphere as well as controlled atmosphere cabinet by using similar welding parameters. The mechanical and metallurgical properties of both weldments were evaluated. Result shows that toughness of the weld metal that was obtained in the controlled atmosphere cabinet much higher than that of classical GMAW process. The metallographic examination also clarified that there was not any gas porosity and inclusion in the weld metal compared with classical process.     

Numerical investigation of droplet impact on the welding pool in gas metal arc welding

A transient three‐dimensional model that describes physical phenomena inside a welding pool during gas–metal arc welding process is presented. The model considers such phenomena as heat‐mass transfer, electromagnetics, hydrodynamic processes and deformation of the weld pool free surface. The fluid flow in the weld pool is induced due to the presence of the mechanical impact of the droplets, thermo‐capillary surface tension, thermal buoyancy and electromagnetic forces. The weld pool surface deformation is calculated by considering arc pressure and droplet impact force. A comparative analysis of the impact of the electric current of the welding arc and different force factors causing the motion of liquid metal in the weld pool on the shape of the welded seam was carried out and discussed.     

Numerical simulation on interaction between TIG welding arc and weld pool

The interface deformation between welding arc and weld pool is important in dynamic coupling numerical simulation on arc and pool. To reveal the interaction between welding arc and weld pool, unified mathematic model of TIG welding arc and pool was established in this paper. The moving interface was solved by updating the calculation region of arc and weld pool continually. Fluid flow and heat transfer of TIG welding arc and weld pool were analyzed basing on this model. The weld pool shape calculated by dynamic coupling welding arc and pool is more close to the experiment than that of non coupling calculation.     

等离子+缆式焊丝脉冲GMAW复合焊熔池流体行为研究

目的 研究等离子+缆式焊丝脉冲GMAW复合焊过程的熔池流体行为.方法 综合考虑传热学以及流体动力学,建立Fluent数值分析模型.使用双椭球–锥体热源模型代表等离子弧焊传热模型,用双椭球热源表征GMAW电弧传热并考虑熔滴传热,同时考虑熔池受到的电磁力、浮力、表面张力、等离子流力等作用力.基于Fluent软件,对复合焊过...     

Modelling of arc welding: The importance of including the arc plasma in the computational domain

We present results of computational simulations of tungsten-inert-gas and metal-inert-gas welding. The arc plasma and the electrodes (including the molten weld pool when necessary) are included self-consistently in the computational domain. It is shown, using three examples, that it would be impossible to accurately estimate the boundary conditions on the weld-pool surface without including the arc plasma in the computational domain. First, we show that the shielding gas composition strongly affects the properties of the arc that influence the weld pool: heat flux density, current density, shear stress and arc pressure at the weld-pool surface. Demixing is found to be important in some cases. Second, the vaporization of the weld-pool metal and the diffusion of the metal vapour into the arc plasma are found to decrease the heat flux density and current density to the weld pool. Finally, we show that the shape of the wire electrode in metal-inert-gas welding has a strong influence on flow velocities in the arc and the pressure and shear stress at the weld-pool surface. In each case, we present evidence that the geometry and depth of the weld pool depend strongly on the properties of the arc.