摩擦条件对磁轨制动器极靴材料与钢轨材料间摩擦因数的影响

将磁轨制动器极靴用铸造Q235B钢和油淬硬化45钢组成销-盘摩擦副进行摩擦试验,研究了滑动速度(10～100 km·h-1)、法向载荷(10～80 N)和润滑条件(干摩擦、水润滑)对摩擦因数和磨损机制的影响.结果表明:随着滑动速度的增大,摩擦副的摩擦因数均在3s内达到稳定;稳定摩擦因数随滑动速度的增大先增大后减小,但变...     

38CrSi自配副的摩擦磨损性能

采用自制的销盘式摩擦磨损试验机研究了38CrSi自配副干滑动时的摩擦因数、磨损率随滑动速度和载荷的变化规律;利用SEM观察了磨损面的微观形貌,分析了摩擦磨损机理。结果表明:其摩擦因数随着载荷和速度的增加而减小;磨损率随着载荷的增加而增大,随着速度的增加先增大后减小,和常用材料的磨损率随速度增加而增大的规律不同;磨损机理为磨粒磨损和粘着磨损。     

38CrSi自配副的摩擦磨损性能

采用自制的销盘式摩擦磨损试验机研究了38CrSi自配副干滑动时的摩擦因数、磨损率随滑动速度和载荷的变化规律;利用SEM观察了磨损面的微观形貌,分析了摩擦磨损机理。结果表明：其摩擦因数随着载荷和速度的增加而减小;磨损率随着载荷的增加而增大,随着速度的增加先增大后减小,和常用材料的磨损率随速度增加而增大的规律不同;磨损机理为磨粒磨损和粘着磨损。     

高水基液压阀陶瓷摩擦副摩擦学性能研究

为选择适合的高水基乳化液液压阀摩擦副材料,探讨ZrO2与不同结构陶瓷组成的摩擦副在高水基乳化液润滑状态下的摩擦磨损特性。采用摩擦磨损试验机,在不同载荷和滑动速度下,研究在高水基乳化液介质中4种不同陶瓷材料（ZrO2、Al2O3、Si3N4和SiC）分别与ZrO2配副的摩擦学性能,并探讨不同组合陶瓷摩擦副的磨损机制。结果表明：在高水基乳化液中,各陶瓷的摩擦因数均随着滑动速度的增大而降低,其中Al2O3陶瓷的摩擦因数最小;ZrO2、Al2O3和Si3N4陶瓷的摩擦因数受载荷的影响较小,SiC陶瓷的摩擦因数则随着载荷的增大而骤增;各陶瓷的磨损体积都随着速度和载荷的增大而增大,其中Al2O3/ZrO2陶瓷摩擦副的磨损体积最小,其磨损机制以磨粒磨损和微疲劳磨损为主。研究表明,在不同工况下,Al2O3与ZrO2陶瓷配副的摩擦因数和磨损体积均为最低值,更适合作为高水基乳化液液压阀的摩擦副材料。     

永磁场条件下45钢与GCr15钢摩擦磨损性能试验研究

基于HSR-2M高速往复摩擦磨损试验机,研究在永磁体磁场条件下滑动速度、载荷等参数对45#钢/GCr15钢摩擦副摩擦学性能的影响,通过磨痕形貌分析其磨损机制,并与无磁场条件下的试验结果进行对比。试验结果表明:磁场的引入可以在一定程度上减小摩擦因数和降低磨损率,证明磁场能够改善45#钢/GCr15钢摩擦副的摩擦学性能;增大滑动速度将降低摩擦因数和磨损率,增大载荷将降低摩擦因数,增加磨损率。无磁场时,摩擦副的摩擦磨损为典型的磨粒磨损,磨损系统的磨损率和摩擦因数较大;有磁场时,磨损形式主要为黏着磨损,摩擦因数和磨损率较小。     

浸金属碳滑板/铜银合金接触线载流摩擦磨损性能的试验研究

选取地铁刚性接触网中现役的浸金属碳滑板与铜银合金接触线为接触副,模拟地铁弓网的实际运行状况,在环-块式试验机上研究直流电流为200~400 A、法向载荷为15~40 N、滑动速度为40~120 km/h工况下浸金属碳滑板载流摩擦磨损性能。结果表明：摩擦因数随电流和滑动速度的增大而减小,随法向载荷的增大而增大;磨损量随电流和滑动速度的增大而增大,当电流较小时（如200 A）,磨损量和法向载荷之间存在一个阈值,当电流较大时（如400 A）,磨损量随法向载荷的增大而减小;滑板温度随电流的增大而增大,随法向载荷增大而减小,当电流较小时（如200 A）,滑板温度随速度的增大而增大,当电流较大时（如400 A）,滑板温度随速度的增大而减小;当电流为200~300 A时,其磨损机制主要为机械磨损,当电流为300~400 A时,其磨损机制主要为氧化磨损和电弧烧蚀。     

油润滑对镍钨合金刷镀层摩擦学性能的影响

为了将镍基合金刷镀技术应用于机械装备的摩擦构件中,运用电刷镀工艺制备了镍钨合金(Ni-W)镀层,研究了油润滑条件下镍钨合金刷镀层的摩擦磨损行为与机制.研究结果表明:油润滑显著地降低了镍基合金刷镀层的摩擦因数和磨损率,且可使摩擦因数随时间变化的波动幅度大大减少,并有效提高了刷镀层由轻微磨损向严重磨损的临界载荷.低载荷和油润滑条件下,镍钨合金刷镀层磨损机制主要是微观切削磨损和多次塑变磨损;高载荷条件下,镀层的磨损机制表现为微观断裂磨损为主,并伴随晶粒剥落现象.     

基于标准销—盘试验的石墨/硬质合金副滑动摩擦磨损特性研究

通过标准销—盘摩擦磨损试验对石墨与硬质合金副的滑动摩擦磨损特性进行深入研究。结果表明,硬质合金销表面有石墨转移膜形成,并发生了轻微的"抛光"磨粒磨损;提高法向载荷和滑动速度可增加石墨转移膜形成,从而降低摩擦因数;与石墨高速铣削试验的刀具磨损结果进行对比发现,标准销—盘摩擦磨损试验未能复制硬质合金刀具的严重磨损现象,说明该摩擦试验方法对于石墨切削摩擦行为的研究具有一定的局限性,需要进一步改进。     

磁场条件下钢轨材料的摩擦磨损性能试验研究

基于HSR-2M高速往复摩擦磨损试验机,试验研究在永磁体磁场条件下,法向载荷、往复速度等参数对钢轨材料摩擦性能的影响,通过磨痕形貌分析其磨损机制,并与无磁场条件下的结果进行对比。试验结果表明:磁场的引入可以在一定程度上减小钢轨材料的摩擦因数、磨损率;增大滑动速度对摩擦因数和磨损率均有减小作用,增大载荷能够降低摩擦因数,但磨损率增加;磁场能够提高钢轨材料在摩擦过程中的磨损性能。无磁场时,钢轨材料磨损形式为典型的磨粒磨损,摩擦系统的磨损率和摩擦因数较大;有磁场时,磨损形式主要为黏着磨损,摩擦因数和磨损率较小。     

旋耕机湿地弯刀的摩擦磨损性能试验研究

利用HSR-2M高速式往复摩擦磨损试验机,研究湿态条件下,湿地弯刀表面粗糙度、往复速度和法向载荷等对旋耕机湿地弯刀摩擦因数和磨损量的影响,并通过磨痕形貌分析其磨损机制。试验结果表明:摩擦因数和磨损量随着旋耕机湿地弯刀表面粗糙度的增大而增大;磨损量随法向载荷的增大而增大,而随往复速度的增大先减小后增大;摩擦表面温度随着法向载荷和相对运动速度的增大而增大;湿态条件下湿地弯刀的磨损机制以磨粒磨损为主,局部有点蚀现象出现。     

Ekonol/石墨/MoS2填料对PTFE力学和摩擦磨损性能的影响

研究了Ekonol含量对Ekonol／石墨／MoS2／P，PTFE复合材料的力学性能、摩擦磨损性能的影响，以及滑动速度、载荷对材料摩擦磨损性能的影响；用扫描电子显微镜观察了复合材料磨损后的表面形貌，并探讨了其磨损机制。结果表明：加入填料降低了材料的拉伸强度和弯曲强度，但提高了弯曲模量和硬度；同时填料能提高材料的磨损性能，但使摩擦因数升高了；当Ekonol含量较低时，磨损机制为粘着磨损，随着填料含量的增加，Ekonol分散到基体中，起到了承载作用，阻止了PTFE基体的带状破坏，磨损机制为疲劳磨损和轻微的粘着磨损；摩擦因数随载荷的增大而减小，随滑动速度的增大而增大，在相同的滑动时间内，磨痕宽度随载荷和滑动速度的增大而增大。     

碳化硼增强铝基复合材料的摩擦磨损性能

为了比较两种含量不同的碳化硼颗粒增强铝基复合材料的摩擦学性能,将其加工成销试样,在多功能摩擦磨损试验机上分别与钢盘试样进行对比摩擦磨损试验,重点研究了接触载荷和相对滑动速度对两种复合材料摩擦磨损性能的影响.结果表明:碳化硼增强铝基复合材料的磨损量随载荷与相对滑动速度的增大而增大,而摩擦因数随载荷与相对滑动速度的增大而减小,较高碳化硼含量的复合材料的耐磨性能比较低含量的复合材料好.     

Friction and wear behavior of flame-sprayed PEEK coatings

Polyetheretherketone (PEEK) becomes of great interest to applications as bearing and slider materials. In this paper, PEEK coatings with three kinds of crystallinities were deposited using the flame spray process. Employing a uniform design experiment, the friction and wear behavior of the three PEEK coatings were systematically investigated under dry sliding conditions against a 100C6 counterbody on a ball-on-disc arrangement for several loads and sliding velocities. For the three coatings, the friction coefficient significantly followed the normal distribution. The average friction coefficients appeared to decrease while increasing the sliding velocity, but were insensitive to the applied load in the range of investigation. Among the three coatings, the higher the crystallinity of the coating, the lower its average friction coefficient was. The wear rate of the coating with the lowest crystallinity decreased with an increase in the load and a decrease in the sliding velocity. The wear rate of the coating with the intermediate crystallinity decreased with an increase in the load, but increased with an increase in the sliding velocity at lower loads, and then decreased with an increase in the velocity at higher loads. The wear rate of the coating with the highest crystallinity decreased with the increase of both the load and the sliding velocity. The wear mechanisms of the different coatings are explained in terms of plastic deformation, plogh marks and fatigue tearing.     

The Study of Arc Rate,Friction, and Wear Performance of C/C Composites in Pantograph–Catenary System

A series of tests on arc rate, friction coefficient, and wear rate of electrical current collectors sliding against overhead contact wires under different conditions was carried out on a high-speed friction and wear testing machine with a pin-on-disc configuration. The worn surface morphology and composition were examined using a scanning electron microscope and energy dispersion spectrum analyzer, respectively. The effects of current, velocity, and load on the arc rate, friction coefficient, and wear rate of C/C composites/QCr0.5 couples were investigated, and the influence mechanism of test parameters on C/C composites was explained. It is concluded that the wear rate increases with an increase in current and velocity and has a decreasing trend with the increase in load. The friction coefficient increases with an increase in velocity and load. The arc rate of C/C composites/QCr0.5 couples increases with an increase in current and velocity. Under the condition of the same current and velocity, when the load is 70 N, the arc rate is the lowest.     

Friction and wear behavior of Ni-P coated Si3N4 reinforced Al6061 composites

Al6061 matrix composite reinforced with nickel coated silicon nitride particles were manufactured by liquid metallurgy route. Microstructure and tribological properties of both matrix alloy and developed composites have been evaluated. Dry sliding friction and wear tests were carried out using pin on disk type machine over a load range of 20-100 N and sliding velocities of range 0.31-1.57 m/s. Results revealed that, nickel coated silicon nitride particles are uniformly distributed through out the matrix alloy. Al6061-Ni-P-Si₃N₄ composite exhibited lower coefficient of friction and wear rate compared to matrix alloy. The coefficient of friction of both matrix alloy and developed composite decreased with increase in load up to 80 N. Beyond this, with further increase in the load, the coefficient of friction increased slightly. However, with increase in sliding velocity coefficient of friction of both matrix alloy and developed composite increases continuously. Wear rates of both matrix alloy and developed composites increased with increase in both load and sliding velocity. Worn surfaces and wear debris was examined using scanning electron microscopy (SEM) for possible wear mechanisms. Energy dispersive spectroscope (EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscope (XPS) techniques were used to identify the oxides formed on the worn surfaces and wear debris.     

On dry sliding friction and wear behaviour of PEEK and PEEK/SiC-composite coatings

In this work, polyetheretherketone (PEEK) and PEEK/SiC-composite coatings were deposited on Al substrates using a printing technique to improve their surfaces performance. The objective of this work was to investigate coatings friction and wear behaviour. Especially, the effect of sliding velocity and applied load on coatings friction coefficient and wear rate was evaluated in range of 0.2-1.4 m/s and 1-9 N, respectively. Compared to Al substrate, the coated samples exhibit excellent friction coefficient and wear rate. For PEEK coating, under an applied load of 1 N, the increase in sliding velocity can result in decreasing of friction coefficient at a cost of wear resistance. Under a load of 9 N, however, PEEK coating exhibits the highest friction coefficient and wear rate at an intermediate velocity. These influences appear to be mainly ascribed to the influence of contact temperature of the two relative sliding parts. In most test conditions, the composite coating exhibits better wear resistance and a little higher friction coefficient. SiC reinforcement in composite coating plays a combined role. First of all, it might lead to energy dissipation for activation of fracture occurred on the interface of PEEK and the powders. Moreover, it can reduce coating ploughs and the adhesion between the two relative sliding parts.     

铜碲硒铁合金的干摩擦磨损性能

利用环-盘式摩擦磨损试验机研究了铜碲硒铁合金的干摩擦磨损行为,分析了载荷和摩擦速度等参数对该合金摩擦磨损性能的影响,并用扫描电子显微镜对磨损形貌进行了观察.结果表明:铜碲硒铁合金的摩擦因数随载荷的增加变化不大,但随摩擦速度的增加而明显增大;合金的磨损率随载荷和摩擦速度的增加均增大;在轻载低速条件下,合金的磨损机制以犁削磨损和粘着磨损为主;在重载高速条件下,磨粒磨损和粘着磨损加剧.     

Tribological Behaviors of Self-lubricating Coating Prepared by Electrospark Deposition

Cu/h-BN self-lubricating coating was prepared on AISI1045 steel by electrospark deposition. The friction coefficient and wear rates were measured using the ball-on-disk method, and the tribological behaviors were discussed. Results showed that the friction coefficient decreased with an increase in sliding speed and load. The wear rate decreased with an increase in sliding speed and increased with an increase in load. The self-lubricating coating exhibited much lower friction coefficient and wear rate than the uncoated mild steel under the test condition. SEM micrographs show that the main wear mechanisms of the self-lubricating coating are abrasive wear and fatigue wear.     

Sliding wear behavior of planar random zinc-alloy matrix composites

The friction and wear behavior of planar random zinc-alloy matrix composites reinforced by discontinuous carbon fibres under dry sliding and lubricated sliding conditions has been investigated using a block-on-ring apparatus. The effects of fibre volume fractions and loads on the sliding wear resistance of the zinc-alloy matrix composites were studied. Experiments were performed within a load range of 50–300 N at a constant sliding velocity of 0.8 m s⁻¹. The composites with different volume fractions of carbon fibres (0–30%) were used as the block specimens, and a medium-carbon steel used as the ring specimen. Increasing the carbon fibre volume fraction significantly decreased the coefficient of friction and wear rates of both the composites and the medium-carbon steel under dry sliding conditions. Under lubricated sliding conditions, however, increasing the carbon fibre volume fraction substantially increased the coefficient of friction, and slightly increased the wear of the medium-carbon steel, while reducing the wear of the composite.Under dry sliding conditions, an increasing load increased not only the wear rates of both the composite and the unreinforced zinc alloy, but also those of their corresponding steel rings. However, the rate of increase of wear with increasing load for both the composite and its corresponding steel ring was much smaller than for the unreinforced zinc alloy and its corresponding steel ring. The coefficient of friction under dry sliding conditions appeared to be constant as load increased within a load range of 50–150 N for both the composite and the unreinforced zinc alloy, but increased at the higher loads. Under any load the coefficient of friction of the composite was lower than half that of the unreinforced zinc alloy under dry sliding conditions.