Raman Scattering Study of Cubic–Tetragonal Phase Transition in Zr1−xCexO2 Solid Solution

A structural phase transition between the cubic (space group, Fm 3 m) and tetragonal (space group, P 4₂ /nmc) phases in a zirconia–ceria solid solution (Zr_1−xCe_xO₂) has been observed by Raman spectroscopy. The cubic–tetragonal ( c–t" ) phase boundary in compositionally homogeneous samples exists at a composition X₀ (0.8 < X₀ < 0.9) at room temperature, where t " is defined as a tetragonal phase whose axial ratio c/a equals unity. The axial ratio c/a decreases with an increase of ceria concentration and becomes 1 at a composition X'₀ (0.65 < X'₀ < 0.7) at room temperature. The sample with a composition between X₀ and X'₀ is t " ZrO₂. By Raman scattering measurements at high temperatures, the tetragonal ( t" ) → cubic and cubic → tetragonal phase transitions occur above 400°C in Zr_0.2 Ce_0.8O₂ solid solution.     

Study of Cation Ordering in Ba(Yb1/2Ta1/2)O3 by X-Ray Diffraction and Raman Spectroscopy

The complex perovskite Ba(Yb_1/2Ta_1/2)O₃ has been prepared by the two-stage solid-state reaction method. Rietveld' refinement analysis indicates cubic perovskite phase with space group     . The 1:1 cation ordering at the B-site is revealed by the presence of (111) superlattice reflection in the X-ray diffraction pattern and further evidenced by the presence of A_1g and F_2g vibrational modes in the Raman spectra. The dielectric constant is measured to be 29.1, the product of quality factor and resonant frequency ( Q × f ) is found to be 32,000 GHz and the temperature coefficient of resonant frequency (τ_f) is 135 (ppm/°C) in the temperature range 30–70°C.     

Cubic-to-Tetragonal Displacive Transformation in Gd2O3–Bi2O3 Ceramics

Gd₂O₃-doped Bi₂O₃ polycrystalline ceramics containing between 2 and 7 mol% Gd₂O₃ were fabricated by pressureless sintering powder compacts. The as-sintered samples were tetragonal at room temperature. Hightemperature X-ray diffraction (XRD) traces showed that the samples were cubic at elevated temperatures and transformed into the tetragonal polymorph during cooling. On the basis of conductivity measurements as a function of temperature and differential scanning calorimetry (DSC), the cubic → tetragonal as well as tetragonal → cubic → teansition temperatures were determined as a function of Gd₂O₃ concentration. The cubic → tetragonal transformation appears to be a displacive transformation. It was observed that additions of ZrO₂ as a dopant, which is known to suppress cation interdiffusion in rare-earth oxide–Bi₂O₃ systems, did not suppress the transition, consistent with it being a displacive transition. Annealing of samples at temperatures 660°C for several hundred hours led to decomposition into a mixture of monoclinic and rhombohedral phases. This shows that the tetragonal polymorph is a metastable phase.     

Raman Spectroscopic Study of Gallium-Doped Ba(Zn1/3Ta2/3)O3

Resonators of Ba(Zn_1/3Ta_2/3)O₃, sintered between 1450° and 1600°C, are characterized by Raman spectroscopy, X-ray diffraction, and scanning electron microscopy. The quality factors of the resonators are found to depend on sintering temperature, and at 1600°C there is evidence of Zn loss from the surface. The frequency of the A_1g Raman mode changes from 800.9 cm⁻¹ for a sample with Q = 80000 (2 GHz), to 794.5 cm⁻¹ when Q = 44000 (2 GHz). Changes in the position of this and other Raman modes are thought to be due to distortions of the oxygen octahedra, brought about by Zn loss. The presence of a BaTa₂O₆ phase at the surface is confirmed by XRD and SEM.     

Raman Study of Glasses of Ba2TiSi2O8 and Ba2TiGe2O8

Raman spectra are reported for fresnoite (Ba₂Ti(Si,Ge)₂O₈ glasses, and comparison is made between the Raman spectra of the corresponding crystalline powders and glasses of Ba₂TiSi₂O₈ and Ba₂TiGe₂O₈. The Ba₂TiGe₂O₈ glass spectra show correspondence with the Ba₂TiGe₂O₈ crystalline Raman spectra; the v _s(Ge–O–Ge) mode occurs at 518 cm⁻¹ in the glass and at 521 cm⁻¹ in the crystalline material. Five-fold coordinated titanium is the majority species present in the Ba₂TiGe₂O₈ glass as revealed by a strong band at 824 cm⁻¹ in the I glass spectrum. The Ba₂TiSi₂O₈ glass spectra are similar to the Ba₂TiSi₂O₈ crystalline spectrum; the strongest band is found at 836 cm⁻¹ in the I glass spectrum. Through comparison with the previous Raman data of other titania silicate glasses, we conclude that the Ba₂TiSi₂O₈ glass has a structure similar to the crystalline phase.     

Analysis of Phase Coexistence in Fe2O3-Doped 0.2PZN–0.8PZT Ferroelectric Ceramics by Raman Scattering Spectra

In this work, we suggested a method to evaluate quantitatively the effect of doping oxide on the phase coexistence of PbZr_{1− x} Ti _x O₃ (PZT)-based ceramics through the analysis of the Raman scattering spectra. Theoretically, the degenerated T _3u mode in the cubic phase of PZT will transform as A ₁(3) and E (4) modes in the tetragonal phase or as rhombohedral ( R ) modes in the rhombohedral phase below the Curie temperature, which set up the theoretical base to study the phase coexistence in ferroelectric materials. Through separation by fitting of the Raman bands, the shifts and intensities of different Raman vibration modes were determined. A calculation equation representing the phase coexistence was put forward based on the theoretical analysis of the degenerated T _3u modes. The results showed that a turning point appears at the Fe₂O₃ addition of 0.3%. The variation in the electrical properties of the Fe₂O₃-doped Pb(Zn_1/3Nb_2/3)O₃ (PZN)–PZT ceramics also affirmed the turning point of the phase evolution as the addition of Fe₂O₃.     

Low-Temperature Structural Phase Transition in ZrO2–12 mol% CeO2 Studied by Infrared Spectroscopy and X-ray Diffractometry

The low-temperature tetragonal ( t ) to monoclinic ( m ) phase transition in ZrO₂–12 mol% CeO₂ was studied by Fourier-transform infrared spectroscopy and X-ray diffractometry (XRD). When the ZrO₂–12 mol% CeO₂ was cooled, the t → m phase transition occurred at about 120 K; this caused significant changes in the infrared reflectance spectra and X-ray diffractograms. As the phase transition proceeded, "difference spectra" obtained by subtracting the infrared spectra before and after the phase transition revealed two infrared modes at 575 and 740 cm⁻¹ which were assigned to the m phase. The volume fraction of the m phase (determined by XRD) and the subtraction coefficient (defined such that the difference spectra reproduced the infrared spectrum of m -ZrO₂) were consistent with each other; this revealed a marked discontinuity at about 120 K. Full width at half maximum of the ( 1 11) _m and (111) _t reflections also indicated a similar discontinuity at about 120 K.     

Raman Spectrum of PbZrO3

Laser-induced Raman spectra were obtained for powders and multidomain single crystals of PbZrO₃ at room temperature. Factor-group analysis was used to interpret the spectra on the basis of the space group C_2v⁸-Pba 2. Raman spectra were also observed for single crystals of PbZrO₃ at several other temperatures between 76° and 520°K and related to crystal structural changes. No first-order Raman bands were noted above the Curie temperature, indicating a phase transformation to a cubic zirconate structure. The interpretation of Raman spectra for thermally decomposed PbZrO₃ is discussed.     

The Effect of Deposition Temperature and Postanneal on the Bi3.63Pr0.3Ti3O12 thin Films Prepared by RF-Magnetron Sputtering Method

Praseodymium doped Bi₄Ti₃O₁₂ (BTO) thin films with composition Bi_3.63Pr_0.3Ti₃O₁₂ (BPT) were successfully prepared on Pt/Ti/SiO₂/Si substrates by RF-magnetron sputtering method at substrate temperatures ranging between 500° and 750°C. The structural phase and orientation of the deposited films were investigated in order to understand the effect of the deposition temperature on the properties of the BPT films. As the substrate temperature was increased to 700°C, the films started showing a tendency of assuming a c -axis preferred orientation. At lower temperatures, however, polycrystalline films were formed. The Pt/BPT/Pt capacitor showed an interesting dependence of the remnant polarization (2 P _r) as well as dc leakage current values on the growth temperature. The film deposited at 650°C showed the largest 2 P _r of 29.6 μC/cm². With the increase of deposited temperature, the leakage current densities of films decreased at the same applied field and the film deposited at 750°C exhibited the best leakage current characteristics. In addition, the ferroelectric fatigue and Raman measurements were carried out on the as-prepared, postannealed in air and postannealed in oxygen BPT films. It was revealed that the BPT film postannealed in air exhibited the weakest fatigue-resistance characteristics and highest frequency shifted Raman vibration modes, indicating the highest oxygen vacancy concentration in this film.     

Thin-Foil Phase Transformations of Tetragonal ZrO2 in a ZrO2-8 wt% Y2O3 Alloy

Tetragonal zirconia ( t -ZrO₂) grains in an annealed ZrO₂ 8 wt% Y₂O₃ alloy transformed to orthorhombic ( o ) or monoclinic ( m ) symmetry by stresses induced by localized electron beam heating in the transmission electron microscope. Different transformation mechanisms were observed, depending on foil thickness and orientation of individual grains. In thicker grains (≥150 nm), the transformation proceeded by a burst-like growth of m laths, and this is believed to approximate bulk behavior. In thinner grains near the edge of the foil, usually those with a [100], orientation perpendicular to the thin-foil surface, "continuous" growth of an o or m phase with an antiphase-boundary-containing microstructure was observed. The o phase is believed to be a high-pressure poly-morph of ZrO₂, which forms (paradoxically) as a thin-foil artifact because it is less dense than t -ZrO₂, but more dense than m -ZrO₂. In some very thin grains, the t → m transformation was thermoelastic. Furthermore, a mottled structure often occurred just before the t → m or t → o transformation, which is attributed to surface transformation. Aside from the lath formation, the observed transformation modes are a result of the reduced constraints in thin foils.     

Raman Spectroscopy of Heat-Treated B2O3-SiO2 Glasses

Raman spectra were measured on B₂O₃-SiO₂ glasses heat-treated at different temperatures and for different periods of time. It was found that the intensity ratio of the 810- and 475-cm⁻¹ bands depended on the thermal history and composition of glass. The intensity vs heat-treatment temperature curve exhibited a maximum in the glass-transition temperature range. High-temperature Raman spectra were measured on 0.5B₂O₃-0.5SiO₂ glass, both with increasing and decreasing temperature, between room temperature and 600°C. Above 300°C with increasing temperature, the intensity of the 810-cm⁻¹ band decreased, whereas the intensity of the 475-cm⁻¹ band increased. The changes reversed with decreasing temperature. The reversible change of the intensity of the two bands was interpreted as a reversible formation and decomposition of boroxy rings with temperature. The reaction becomes very sluggish below the glass transition so that the intensity ratio stayed constant below 300°C.     

XRD and Raman Studies on the Ordering/Disordering of Ba(Mg1/3Ta2/3)O3

The samples of complex perovskite Ba(Mg_1/3Ta_2/3)O₃ (BMT) were synthesized at various sintering temperatures and the X-ray diffraction (XRD) patterns and Raman spectra of the samples were collected. Both the structure refinements using the XRD data and the Raman spectra show that the samples sintered above 1500°C with high pellet relative density (>95%) take almost-perfect B-site-ordered structure; while the samples sintered below 1400°C with low pellet relative density (<70%) take the more disordered structure at B-sites. The vibrational modes of 1:2 ordered BMT     were obtained and illustrated by using first-principle calculations. With the assistance of the calculation results, Raman peaks of BMT were assigned as A _1g(1) (107 cm⁻¹), A _1g(2) (212 cm⁻¹), A _1g(3) (433 cm⁻¹), A _1g(4) (798 cm⁻¹), and E _g(1) (104 cm⁻¹), E _g(2) (160 cm⁻¹), E _g(3) (264 cm⁻¹), E _g(4) (386 cm⁻¹), E _g(5) (576 cm⁻¹). The highly ordered BMT sample at B-site shows longer phonon lifetime and weaker coupling among phonons than the disordered BMT, which probably are the intrinsic reasons for the highly ordered BMT sample to have the low dielectric loss.     

Phase Equilibria in the System ZrO2─InO1.5

Phase equilibria in the system ZrO₂─InO_1.5 have been investigated in the temperature range from 800° to 1700°C Up to 4 mol%, InO_1.5 is soluble in t -ZrO₂ at 1500°C. The martensitic transformation temperature m → t of ZrO₂ containing InO_1.5 is compared with that of ZrO₂ solid solutions with various other trivalent ions with different ionic radii. The diffusionless c → t ' A phase transformation is discussed. Extended solid solubility from 12.4 ± 0.8 to 56.5 ± 3 mol% InO_1.5 is found at 1700°C in the cubic ZrO₂ phase. The eutectoid composition and temperature for the decomposition of c -ZrO₂ solid solution into t -ZrO₂+InO_1.5 solid solutions were determined. A maximum of about 1 mol% ZrO₂ is soluble in bcc InO_1.5 phase. Metastable supersaturation of ZrO₂ in bcc InO _1.5 and conditions for phase separation are discussed.     

High-Temperature Transmission Electron Microscopy and X-Ray Powder Diffraction Studies of Polymorphic Phase Transitions in Ba4Nb2O9

Polymorphic phase transitions in Ba₄Nb₂O₉ were studied by thermal analyses, high-temperature transmission electron microscopy and X-ray powder diffractometry. Two stable polymorphs were isolated, low-temperature α-modification and high-temperature γ-modification, with the endothermic phase transition at 1176°C. The α→γ transformation is accompanied by the formation of a 120° domain structure, which is a consequence of hexagonal→orthorhombic unit cell reconstruction. Reheating the presintered γ-Ba₄Nb₂O₉ results in the formation of a metastable γ'-modification (formerly known as β-polymorph) in the temperature range between 360° and 585°C, before the γ→α transformation at 800°C. Above ∼490°C Ba₄Nb₂O₉ becomes moderately sensitive to a loss of BaO. In air the surface of Ba₄Nb₂O₉ grains decomposes to nanocrystalline Ba₅Nb₄O₁₅ and BaO, which instantly reacts with atmospheric CO₂ to form BaCO₃. Surface reaction delays γ→α transformation up to 866°C in air. In vacuum the loss of BaO is even more enhanced and consequently the formation of minor Ba₃Nb₂O₈ phase is observed above 1150°C.     

Temperature Dependence of the Raman Spectra of ZrO2

Raman spectra of ZrO₂ were measured in the range 300° to 1600°K. Irreducible components of the Raman spectra were obtained from polarization measurements at room temperature, and the symmetries of the Raman-active modes in the monoclinic phase were determined. The temperature dependence of the spectra shows a hysteresis. In the temperature range of phase change, two kinds of Raman lines coexist. Six Raman-active mode frequencies were found in the tetragonal phase at high temperatures. Analysis of the spectra showed that the Raman-active modes in the tetragonal phase are affected by strain introduced into the crystals during the phase transformation.     

Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Properties of (Y)ZrO2–Al2O3 and (Y)ZrO2–Al2O3–(Ti or Si)C Composites

The effect of Al₂O₃ and (Ti or Si)C additions on various properties of a (Y)TZP (yttria-stabilized tetragonal zirconia polycrystal)–Al₂O₃–(Ti or Si)C ternary composite ceramic were investigated for developing a zirconia-based ceramic stronger than SiC at high temperatures. Adding Al₂O₃ to (Y)TZP improved transverse rupture strength and hardness but decreased fracture toughness. This binary composite ceramic revealed a rapid loss of strength with increasing temperature. Adding TiC to the binary ceramic suppressed the decrease in strength at temperatures above 1573 K. The residual tensile stress induced by the differential thermal expansion between ZrO₂ and TiC therefore must have inhibited the t - → m -ZrO₂ martensitic transformation. It was concluded that a continuous skeleton of TiC prevented grain-boundary sliding between ZrO₂ and Al₂O₃. In contrast, for the ternary material containing β-SiC in place of TiC, the strength decreased substantially with increasing temperature because of incomplete formation of the SiC skeleton.     

The System TiO2-Bi2Ti4O11

The system TiO₂-Bi₂Ti₄O₁₁ was examined by Raman spectroscopy and X-ray diffraction to determine whether TiO₂ is soluble in Bi₂Ti₄O₁₁. The Raman spectral data obtained from preparations made at ∼ 1050°C and cooled to room temperature led us to conclude that TiO₂ is not soluble in the "high-temperature" form of Bi₂Ti₄O₁₁. It was also found that extensive grinding of the phase identified as the "high-temperature" form converts it to the "low-temperature" form, stable below 250°C.     

Determination of Stoichiometry Variations in LiNbO3 and LiTaO3 by Raman Powder Spectroscopy

Raman spectroscopy of powders is shown to be a sensitive technique for detecting stoichiometry variations. The method makes use of the broadening of the Raman-active modes which occurs when the translational symmetry of the lattice is reduced on deviation from simple, fixed cation ratios in the structure. Application of the technique to the LiNbO₃( ss ) system shows that the room-temperature solid-solution range does not exceed 50±0.5 mol% Nb₂O₅ and that congruent LiNbO₃( ss ) at 51.4 mol% Nb₂O₅ is thermodynamically unstable below ≅800°C. Similarly, application of the Raman method to the LiTaO₃( ss ) system indicates that congruent LiTaO₃( ss ) at 51.0 mol% Ta₂O₅ is unstable at temperatures <1000°C.     

Probing of 1:2 Ordering in Ba(Ni1/3Nb2/3)O3 and Ba(Zn1/3Nb2/3)O3 Ceramics by XRD and Raman Spectroscopy

The 1:2 ordering in Ba(Ni_1/3Nb_2/3)O ceramics sintered at 1350-1500°C has been investigated by using XRD and Raman spectroscopy. Both of the techniques show that the degree of the 1:2 ordering decreases as the sintering temperature increases. However, XRD discerns the 1:2 ordering only for the samples sintered at 1350-1400°C, whereas Raman spectroscopy discerns the 1:2 ordering for all the samples. Similar results have been obtained for Ba(Zn_1/3Nb_2/3)O₃ ceramics, where only the temperature range is slightly different. It is demonstrated that Raman spectroscopy can be a useful tool for probing of the 1:2 ordering in the A(B'^II_1/3B"^V_2/3)O₃-type complex perovskite compounds.