Effects of poly(ethylene‐co‐propylene) elastomer on mechanical properties and combustion behaviour of flame retarded polyethylene/magnesium hydroxide composites

Magnesium hydroxide‐based halogen‐free flame retarded linear low density polyethylene composites containing poly(ethylene‐co‐propylene) elastomer were prepared in the melt process and subsequently vulcanized thermally. Influences of the elastomer on the mechanical properties, combustion characteristics and crystallization behaviour of polyethylene/magnesium hydroxide composites have been investigated. The results from the mechanical tests show that the incorporation of a suitable amount of elastomer into polyethylene/magnesium hydroxide composites after vulcanization can increase both the tensile strength and elongation greatly, compared with those of the composites without the elastomer. It has been found that the properties such as limiting oxygen index, UL‐94 rating, the time to ignition and the rate of heat release of polyethylene/magnesium hydroxide/elastomer composites are all improved in comparison with polyethylene/magnesium hydroxide composites at the same retardant level. Scanning electron microscopy studies show that the incorporation of the elastomer into polyethylene/magnesium hydroxide composites improves the compatibility between the filler and the polymer substrate. The degrees of crystallinity of polyethylene/magnesium hydroxide/elastomer composites decrease with increasing the elastomer content. © 2002 Society of Chemical Industry     

Recycled milk pouch and virgin low‐density polyethylene/linear low‐density polyethylene based coir fiber composites

The viability of the thermomechanical recycling of postconsumer milk pouches [a 50 : 50 low‐density polyethylene/linear low‐density polyethylene (LDPE–LLDPE) blend] and their use as polymeric matrices for coir‐fiber‐reinforced composites were investigated. The mechanical, thermal, morphological, and water absorption properties of recycled milk pouch polymer/coir fiber composites with different treated and untreated fiber contents were evaluated and compared with those of virgin LDPE–LLDPE/coir fiber composites. The water absorption of the composites measured at three different temperatures (25, 45, and 75°C) was found to follow Fickian diffusion. The mechanical properties of the composites significantly deteriorated after water absorption. The recycled polymer/coir fiber composites showed inferior mechanical performances and thermooxidative stability (oxidation induction time and oxidation temperature) in comparison with those observed for virgin polymer/fiber composites. However, a small quantity of a coupling agent (2 wt %) significantly improved all the mechanical, thermal, and moisture‐resistance properties of both types of composites. The overall mechanical performances of the composites containing recycled and virgin polymer matrices were correlated by the phase morphology, as observed with scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis and microstructural characterization of kaolin–polyethylene composites

In this article, the preparation and characterization of kaolin/polyethylene composites are presented. Microstructural characteristics of six different kaolin–polyethylene composites with varying percentage compositions of kaolin and polymer were produced using a modified melt compounding approach, was explored. The characterization methods employed are scanning electron microscopy (SEM), attenuated total reflectance mid Infrared (ATR‐MIR), X‐ray powder diffraction (XRD), thermogravimetric and differential thermal analysis (TGA‐DTA), compressive, flexural strengths and impact resistance analysis. The implications of the results are discussed for the design of kaolin/polymer composites for constructional purposes. POLYM. COMPOS., 35:1507–1515, 2014. © 2013 Society of Plastics Engineers     

Positive temperature coefficient effect and mechanism of compatible LLDPE/HDPE composites doping conductive graphite powders

Linear low density polyethylene (LLDPE)/high density polyethylene (HDPE) blends doped conductive graphite powders were constructed by the traditional melt‐blending method to acquire the conductive compatible polymer composites, and corresponding positive temperature coefficient (PTC) effect of electrical resistivity was investigated. The results indicated that the room‐temperature resistivity gradually decreased and PTC effects were remarkably enhanced by regulating the graphite contents or LLDPE/HDPE ratios. Especially, with increasing graphite contents, the polymer‐fixed composites showed the notable double PTC effects, originating from the volume expansion of the co‐crystallization or their fraction. Whereas, with increasing the LLDPE/HDPE ratio, the PTC effects of the graphite‐fixed composites occurred at the lower temperature, even far below the melting points of the co‐crystallization. Therefore, the regulation of co‐crystallization morphology of compatible polymer matrices was a new idea in the improvement of PTC materials. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46453.     

Processing and characterization of injection moldable polymer–particle composites applicable in brazing processes

A novel method has been developed to process highly filled polymer–particle composites to test samples as braze metal preforms. Polypropylene (PP), low‐density polyethylene (LD‐PE) and high‐density polyethylene (HD‐PE) were used as polymer matrices. Two types of nickel‐based braze metal microparticles (Ni 102 and EXP 152) were compounded to the polymer matrices at filler contents up to 65 vol %. With enhancing filler content, torque at kneading rotors, and injection molding parameter were significantly affected by increasing viscosity. Injection molded composites show well‐distributed spherical microparticles and particle–particle interactions. Polymers decompose residue‐free at temperatures above 550°C, even for their composites. Adding particles reduces polymer crystallinity, whereas defined cooling at 5°C/min significantly increases the crystallinity and melt peak temperature of polymers compared to undefined cooling prior injection molding. Storage modulus of polymers increases significantly by adding filler particles. LD‐PE + 65 vol % EXP 152 show the most suitable composite performance. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of polyethylene‐graft‐maleic anhydride as a compatibilizer on the mechanical and tribological behaviors of ultrahigh‐molecular‐weight polyethylene/copper composites

Ultrahigh‐molecular‐weight polyethylene/copper (UHMWPE/Cu) composites compatibilized with polyethylene‐graft‐maleic anhydride (PE‐g‐MAH) were prepared by compression molding. The effects of the compatibilizer on the mechanical, thermal, and tribological properties of the UHMWPE/Cu composites were investigated. These properties of the composites were evaluated at various compositions, and worn steel surfaces and composite surfaces were examined with scanning electron microscopy and X‐ray photoelectron spectroscopy. The incorporation of PE‐g‐MAH reduced the melting points of the composites and increased their crystallinity to some extent. Moreover, the inclusion of the PE‐g‐MAH compatibilizer greatly increased the tensile rupture strength and tensile modulus of the composites, and this improved the wear resistance of the composites. These improvements in the mechanical and tribological behavior of the ultrahigh‐molecular‐weight‐polyethylene‐matrix composites with the PE‐g‐MAH compatibilizer could be closely related to the enhanced crosslinking function of the composites in the presence of the compatibilizer. Moreover, the compatibilizer had an effect on the transfer and oxidation behavior of the filler Cu particulates, which could be critical to the application of metallic‐particulate‐filled polymer composites in engineering. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 948–955, 2004     

Freeze‐drying method prepared UHMWPE/CNTs composites with optimized micromorphologies and improved tribological performance

Uniformly dispersed carbon nanotubes (CNTs) reinforced ultrahigh molecular weight polyethylene (UHMWPE) composites were successfully prepared by freeze‐drying method. Specifically, polymer powders were mixed with CNT aqueous paste, and then freeze‐dried. As a consequence, CNTs covered at the surface of UHMWPE powders evenly when CNT content was not very high, which improved the quantity of crystals and crystallinity of UHMWPE/CNTs composites by providing more nucleation sites during the upcoming compression‐molded process. Furthermore, optimized dispersion state of CNTs and concomitant higher crystallinity made freeze‐drying technique prepared composites display much lower wear rate when compared with pure UHMWPE and UHMWPE/CNTs composites fabricated by common heat‐drying method. In a word, our proposed method of freeze‐drying is simple and effective for mass production of UHMWPE/CNTs composites, and it is promising to be applied to fabricate many kinds of nanofillers modified polymer composites, for example, polymer/graphene material. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41885.     

Influence of gamma radiation on compatibilized LLDPE/magnesium hydroxide/sepiolite composites

The influence of gamma irradiation on the properties of compatibilized linear low‐density polyethylene/magnesium hydroxide (MH)/sepiolite composites has been investigated. Vinyl triethoxy silane and maleated polyethylene have been used as compatibilizers. The compatibilizing effect in the composites is confirmed by the Fourier transform infrared spectra, which showed the presence of additional chemical bonds, which are responsible for the enhanced polymer‐filler interaction. As a result, the miscibility of the polar additives into the nonpolar polymer matrix is enhanced. The scanning electron micrographs revealed that the additives are well embedded and uniformly dispersed in the polymer matrix without any voids. The known thermal decomposition temperature of MH (～ 350°C) is also increased in the compatibilized composites. In addition, 150 kGy irradiated composite showed a remarkable improvement of 37°C in the onset degradation temperature of unirradiated composite. Furthermore, the formation of radiation crosslinked structure in the composites also improved the mechanical properties of the composites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of functionalized low density polyethylene matrix biocomposites

The incorporation of cellulosic fibers into polyethylene matrices was studied in this work, by dispersion of fluff pulp from maritime pine in a hot polymer solution, followed by co‐precipitation of the solid components by cooling at room temperature. The above method was found suitable for proper wetting and dispersion of fibers in the polymeric matrix, as compared with melt compounding. Unmodified low density polyethylene [LDPE], modified LDPE with maleic anhydride grafted linear low density polyethylene [M‐LLDPE] and a copolymer of acrylic acid and n‐butyl acrylate polyethylene [(AA/n‐BA)‐LDPE], were used as matrices for the preparation of fiber reinforced composites. The thermal properties of these composites were determined using differential scanning calorimetry and thermogravimetric analysis. The incorporation of cellulosic fibers results in a decrease of the crystallinity of the polymer matrix, as they act as inert material. In addition, the appropriate tests were run in order to determine the density and tensile properties of the composite specimens prepared by compression molding, with filler content ranging from 10 to 40% (w/w). Composites based on modified LDPE showed improved mechanical properties. The Takayanagi model, applied to predict the Young's modulus of composites, was in very good agreement with the experimental data obtained in this work. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Morphological,mechanical, and physical properties of composites made with wood flour‐reinforced polypropylene/recycled poly(ethylene terephthalate) blends

Wood flour (WF)‐filled composites based on a polypropylene (PP)/recycled polyethylene terephthalate (r‐PET) matrix were prepared using two‐step extrusion. Maleic anhydride grafted polypropylene (MAPP) was added to improve the compatibility between polymer matrices and WF. The effects of filler and MAPP compatibilization on the water absorption, mechanical properties, and morphological features of PP/r‐PET/WF composites were investigated. The addition of MAPP significantly improved mechanical properties such as tensile strength, flexural strength, tensile modulus, and flexural modulus compared with uncompatibilized composites, but decreased elongation at break. Scanning electron microscopic images of fracture surface specimens revealed better interfacial interaction between WF and polymer matrix for MAPP‐compatibilized PP/r‐PET/WF composites. MAPP‐compatibilized PP/r‐PET/WF composites also showed reduced water absorption due to improved interfacial bonding, which limited the amount of absorbable water molecules. These results indicated that MAPP acts as an effective compatibilizer in PP/r‐PET/WF composites. POLYM. COMPOS., 38:1749–1755, 2017. © 2015 Society of Plastics Engineers     

Study on the rheological behaviors of UHMWPE/CA‐MMT nanocomposite

In our previous study, we have prepared a novel antibacterial ultra‐high molecular weight polyethylene/chlorhexidine acetate‐montmorillonoid (UHMWPE/CA‐MMT) composites and examined its crystallization process and kinetics [1]. In this work, the rheological behaviors of pure UHMWPE, UHMWPE/MMT, UHMWPE/CA, and UHMWPE/CA‐MMT were characterized. The results showed that MMT can increase the viscosity of the polymer composites and CA can act as a plasticizer in the composites. Compared with UHMWPE/CA, UHMWPE/CA‐MMT had lower η*, G′, and G″. The TGA result indicated that CA‐MMT has higher thermostability than CA. Hence, CA‐MMT has the lower thermal decomposition ratio at high temperature than CA when it is blended with polymer. The TGA result could be used to explain that UHMWPE/CA‐MMT composites had better plasticizer effect than UHMWPE/CA composites. POLYM. COMPOS., 36:47–50, 2015. © 2014 The Authors Polymer Composites published by Wiley Periodicals, Inc.     

Effects of compatibilizer,compounding method,extrusion parameters,and nanofiller loading in clay‐reinforced recycled HDPE/PET nanocomposites

Nanocomposites based on recycled high density polyethylene (rHDPE), recycled polyethylene terephthalate (rPET), and organoclay (C10A) were made using twin screw extruder followed by hot pressing. The independent effects of polymer/clay compatibility, preparation method, extrusion parameters, and clay loadings were investigated. Ethylene‐glycidyl methacrylate could effectively improve the compatibilization of immiscible rHDPE/rPET blend with clay, which confirmed by the good polymers‐clay adherence and domain size reduction obtained in scanning electron microscopy images. Although intercalated structures were observed in the composites made by one‐step compounding, in the composites prepared by two‐step extrusion method, enhanced dispersion of clay in polymer blend was found from X‐ray diffraction results. Higher extrusion temperature and intermediate speed of rotation (90 rpm) appeared to increase the mechanical properties due to improvement of nanofiller dispersion in matrix. Results showed that the stiffness increased whereas tensile and impact strength decreased with clay content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42287.     

Microwave‐absorbing properties of linear low‐density polyethylene/ethylene–octene copolymer/carbonyl iron powder composites

Using linear low‐density polyethylene (LLDPE)/ethylene–octene copolymer (POE) as a polymer matrix and carbonyl iron powders (CIPs) as filler, we prepared polymer matrix composites with microwave‐absorbing properties by means of melt blending. Scanning electron microscopy and transmission electron microscopy were used to characterize the samples. The absorbing properties of the composites were measured with the arch method in the range of frequency 2.0–18.0 GHz. The results indicate that the absorbing peaks moved to low frequency as the CIP content in composites increased and that there was an appropriate CIP content in LLDPE/POE/CIP composites to achieve the best absorbing effectiveness. The electromagnetic parameters of the composites were determined with the transmission/reflection method in the range 2.6–17.8 GHz. The experimental results show that there were both dielectric loss and magnetic loss in the LLDPE/POE/CIP composites. Therefore, the microwave absorption of the LLDPE/POE/CIP composites was attributed to the combining contributions of the dielectric loss and magnetic loss. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Deformation and fracture of Mg(OH)2‐filled polyolefin composites under tensile stress

The tensile behavior of high‐density polyethylene (HDPE), polypropylene (PP), and linear low‐density polyethylene composites containing a titanate coupling agent and silicone‐oil‐treated magnesium hydroxide [Mg(OH)₂] was studied. The increase in the extent of the ultimate elongation of the composites was affected by the yield stress and the strain‐hardening tendency of the polymer matrix in the composites. Ethylene–propylene–diene rubber and octane–ethylene copolymer were introduced to adjust the yield stress of PP and HDPE. Although the ultimate elongation of PP/elastomer and HDPE/elastomer blends was higher than that of virgin PP or HDPE, the ultimate elongation of the filled composites dropped at a high content of Mg(OH)₂. Scanning electron microscopy showed that the difference in the uniformity of the interface exfoliation decreased with the yield stress of the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3248–3255, 2003     

Esterification effect of maleic anhydride on swelling properties of natural fiber/high density polyethylene composites

The natural fibers (banana, hemp, and sisal) and high density polyethylene were taken for the preparation of natural fiber/polymer composites in different ratios of 40 : 60 and 45 : 55 (w/w). These fibers were esterified with maleic anhydride (MA) and the effect of esterification of MA was studied on swelling properties in terms of absorption of water, at ambient temperature, and steam. It was found that the steam penetrates more within lesserperiod of time than water at ambient temperature. Untreated fiber composites show more absorption of steam and water in comparison to MA‐treated fiber composites. The more absorption of water was found in hemp fiber composites and less in sisal fiber composites. Steam absorption in MA‐treated and untreated fiber composites are higher than the water absorption in respective fiber composites. The natural fiber/polymer composites containing low amount of fibers show less absorption of steam and water at ambient temperature than the composites containing more amount of fibers in respective fiber composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Wood‐thermoplastic composites from wood flour and high‐density polyethylene

High‐density polyethylene/wood flour (HDPE/WF) composites were prepared by a twin‐screw extruder. The effects of WF, silane coupling agents, polymer compatibilizers, and their content on the comprehensive properties of the WF/HDPE composites have been studied in detail, including the mechanical, thermal, and rheological properties and microstructure. The results showed that both silane coupling agents and polymer compatibilizers could improve the interfacial adhesion between WF and HDPE, and further improve the properties of WF/HDPE composites, especially with AX8900 as a compatibilizer giving higher impact strength, and with HDPE‐g‐MAH as a compatibilizer giving the best tensile and flexural properties. The resultant composite has higher strength (tensile strength = 51.03 MPa) and better heat deflection temperature (63.1°C). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Jatropha deoiled cake filler‐reinforced medium‐density polyethylene biocomposites: Effect of filler loading and coupling agent on the mechanical,dynamic mechanical and morphological properties

This work focuses on the performance of Jatropha deoiled cake (JOC) as filler for medium‐density polyethylene. The biocomposites were prepared using a melt‐compounding technique. Maleated polyethylene (MPE) was used as a reactive additive to promote polymer/filler interfacial adhesion. The mechanical, thermodynamic mechanical and morphological properties of the resultant composites were investigated. The results show that the incorporation of JOC into the matrix reduced tensile, flexural, and impact strengths compared with the pure matrix. Moreover, tensile and flexural moduli were increased. The composites prepared with MPE had better mechanical properties and lower water uptake, indicating an enhancement in the interfacial interaction between JOC and polyethylene systems. The storage modulus was increased by the increase in filler loading and decreased when MPE was used. The composites loss modulus curves revealed two glass transitions indicating partial miscible blends. Scanning electron microscopy analysis for maleated composites showed a relatively homogeneous morphology with few left cavities, and the filler particle size is smaller compared to nontreated composites. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Effect of morphology on the electric conductivity of binary polymer blends filled with carbon black

Several carbon black (CB)‐filled binary polymer blends were prepared in Haake rheometer. Distribution states of CB and effect of morphology on the electric conductivity of different ternary composites were investigated. Under our experimental condition CB particles located preferentially at the interface between polymethyl methacrylate (PMMA) and polypropylene (PP) in PMMA/PP/CB composites, in high‐density polyethylene (HDPE) phase in PP/HDPE/CB composites, and in Nylon6 (PA6) phase in polystyrene (PS)/PA6/CB, PP/PA6/CB, PMMA/PA6/CB, and polyacrylonitrile (PAN)/PA6/CB composites; the ternary composites in which CB particles locate at the interface of two polymer components have the highest electric conductivity when the mass ratio of the two polymers is near to 1 : 1. The ternary composites in which CB particles located preferentially in one polymer have the highest electric conductivity usually when the amount of the polymer component having CB particles is comparatively less than the amount of the polymer component not having CB particles; if the formulations of PS/PA6/CB, PP/PA6/CB, and PMMA/PA6/CB composites equaled and PA6/CB in them is in dispersed phase, PS/PA6/CB composites have the highest electric conductivity and PP/PA6/CB composites have the lowest electric conductivity; suitable amount of PS or PAN in PA6/CB composites increase the electric conductivity due in the formation of a parallel electrocircuit for electrons to transmit. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Investigation on the uniformity of high‐density polyethylene/wood fiber composites in a twin‐screw extruder

Uniform dispersion of wood fiber in high‐density polyethylene can improve the mechanical properties and surface finish of the wood plastic composites. However, it is difficult to achieve uniform dispersion when the wood content is high, due to its low thermal stability, incompatibility with polymer, and affinity for agglomeration. This work was undertaken to improve the uniformity of high‐density polyethylene/wood composites by designing screw configurations, optimizing screw speed, and altering material compositions. The rheological properties and scanning electron microscope micrograph were used to characterize the uniformity. The results showed that the medium dispersive and distributive mixing, medium screw speed, and lubricant were all beneficial in improving uniformity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Properties of kenaf fiber/polylactic acid biocomposites plasticized with polyethylene glycol

Biocomposites of kenaf fiber (KF) and polylactic acid (PLA) were prepared by an internal mixer and compression molding. PLA was plasticized with polyethylene glycol (PEG) (10 wt%) and evaluated as the polymer matrix (p‐PLA). Fiber loadings were varied between 0 and 40 wt%. The tensile, dynamic mechanical, and morphological properties and water absorption behavior of these composites were studied. Reinforcing effect of KF was observed when fiber loading exceeded 10 wt% despite of the inferior fiber‐matrix adhesion observed via scanning electron microscopy (SEM). Un‐plasticized PLA/KF composite exhibited higher tensile properties than its plasticized counterpart. Fiber breakage and heavily coated short pulled‐out of fibers were observed from the SEM micrographs of the composite. The presence of PEG might have disturbed the fiber‐matrix interaction between KF and PLA in the plasticized composites. Addition of PEG slightly improved the un‐notched impact strength of the composites. Dynamic mechanical analysis showed that the storage and loss moduli of p‐PLA/KF composites increased with the increase in fiber loading due to increasing restrictions to mobility of the polymer molecules. The tan delta of the composites in contrast showed an opposite trend. p‐PLA and p‐PLA/KF composites exhibited non‐Fickian behavior of water absorption. SEM examination revealed microcracks on p‐PLA and p‐PLA/KF surfaces. POLYM. COMPOS., 31:1213–1222, 2010. © 2009 Society of Plastics Engineers