Study of mechanical properties of micromachined dental implants

Advancements in technologies and techniques within the dental industry have given rise to new and effective tooth replacement procedures for damages resulting from causes such as trauma or aging. While these treatments are widely available for patients, they remain highly expensive, preventing patients from much-needed dental care. The elevated cost of dental implants is in part associated with their components that are mainly available through third-party companies at a premium cost. To be cost effective, dental laboratories are exploring the option of producing their own dental implant components, and are therefore acquiring knowledge of manufacturing techniques and quality assurance expertise to produce quality components. In order to ensure high quality and reliability, the fabricated components must be tested and benchmarked against current implants on the market. The present study examines the micro machining process of dental implants, specifically for the abutments and screws, and its impact on the mechanical properties of the components. To achieve this, dental implant abutment and screw prototypes were fabricated, experimentally tested, and compared. The impact of different machining processes on the mechanical properties of the implants was comparatively determined and analysed. The fabricated implant testing results show coherent mechanical properties displayed by good hardness, and material microstructures similar to market components, indicating a high level of prototype quality.     

Affordable implant prosthetics using a screwless implant system

Many dentists have been reluctant to place dental implants because they have found that most implants are costly and time-consuming to place and have long-term maintenance problems. Most of these problems are caused by using screws to connect the abutment to the implant, the crown to the abutment or both. The use of a screwless implant system and conventional prosthetics, the author contends, can make implant dentistry affordable, versatile and easy to incorporate into all general dental practices.     

Quantitative histologic evaluation of LTI carbon, carbon-coated aluminum oxide and uncoated aluminum oxide dental implants

The response of mandibular bone to identical geometry LTI carbon, carbon-coated aluminum oxide, and uncoated aluminum oxide blade-type dental implants in baboons for 2 years was evaluated using histologic, microradiographic, and scanning electron microscopic methods. In addition, a quantitative histologic analysis was performed identifying the type, amount, and distribution of tissue surrounding the dental implant systems. This is the final phase of a study investigating the effect of implant elastic modulus and implant surface chemical composition on the performance of dental implants. Previous studies have utilized clinical and radiographic evaluations, postretrieval mechanical testing, and finite element stress analysis to evaluate the dental implant performance. The results of the histologic study revealed a direct implant-bone interface with no intervening soft tissue in 16 of the 21 implants (76%). A fibrous tissue interface was observed in 5 of 21 implants (24%). Quantitative histologic results for the implants with a direct implant-bone interface showed statistically larger crestal cortical plates (p less than 0.05) and greater area fraction crestal cancellous bone (p less than 0.05) in the LTI carbon implant compared to the carbon-coated and uncoated aluminum oxide implants. The carbon-coated and uncoated aluminum oxide implants demonstrated statistically greater area fraction cancellous bone at the inferior region of the implant (p less than 0.05) and thinned and reduced crestal cortical plates when compared to the LTI carbon implants. The results indicate that significant stress shielding of the crestal bone had occurred with the rigid carbon-coated and uncoated aluminum oxide implants when compared to the LTI carbon implants which had a material elastic modulus similar to cortical bone. Based upon the histologic results, it appears that the LTI carbon implants with the direct implant-bone interface exhibited a greater potential for long-term successful performance compared to the aluminum oxide substrate implants.     

The nonsubmerged osseointegrated dental implant

Implant patients are seeking means of restoring their health and appearance with minimal side effects. Dental implant surgery must react to these demands by continuing to develop minimally invasive implant surgery techniques, imaging that customizes surgical procedures, and materials and drugs that reduce surgical costs and complications, shorten recovery, and increase the longevity of components, enabling patients to live active lifestyles. Nonsubmerged osseointegrated implants fit nicely into the future of dental surgery.     

Altered patterns of DNA methylation on chromosomes from leukemia cell lines: identification of 5-methylcytosines by indirect immunodetection

The feasibility of implant treatment in patients after oral ablative tumor surgery has not yet been investigated with consideration of the requisite high periodontal standards. A report on this topic has to deal not only with implant survival but also with implant health, bone response, soft tissue health, failure pattern, time of failure, and ease of restoration. For the assessment of an implant system, an overview must be accomplished that takes into account the different restorations used and their interaction with the implant system that was used. This study presents the Bone-Lock implant system (Howmedica Leibinger GmbH, Freiburg, Germany) in a retrospective investigation after 5 years of follow-up with special emphasis on the prosthetic restorations used following resection of oral malignancies. From early in 1990 through June 1996, we inserted 210 dental endosteal Bone-Lock implants (58 patients) after oral tumor resectioning. Included in the study were 45 patients with 162 implants and prosthetic restorations that had been loaded for 1 year (dentures retained by telescopic or bar-clip or ball attachments, implant-supported prostheses, tooth-to-implant connected bridges). Regular follow-up consisted of evaluation of the Plaque Index (Silness and L?e) and of the Sulcus Bleeding Index (L?e), measurements of pocket probing depth, implant mobility (by means of the Periotest method), bone resorption (according to X-ray findings), and a questionnaire that registered patient satisfaction. The results were evaluated for each restoration and were compared with baseline standards. The overall 5-year survival rate was 83.2%. For implants that had been in place for over 365 days, the survival rate was 93%. The investigation showed that after resection of oral malignancies, patients could be treated with dental implants and superstructures with long-term efficacy similar to that found in healthy subjects considering internationally accepted standards. Implant treatment in tumor patients appeared to offer the most positive periodontic results when use of bar-clip or telescope-retained overdentures was involved. The patient satisfaction level with the described prosthodontic treatment was satisfactory.     

Histologic evaluation of the LaminOss osteocompressive dental screw: a pilot study

This animal study compared the response of canine mandibular bone using the orthopedic principle of osteocompression by the function of an immediately loaded dental implant vs an unloaded dental implant of the same design and size. Two dogs were partially edentulated in the mandible. A total of 8 osteocompressive screw implants, 2 per quadrant were placed and evaluated histomorphometrically after 3 days in 1 dog and after 3 months in the second dog. The second dog had a two-unit fixed bridge placed immediately postsurgically in occlusal function on the right side; on the left side, the implants were splinted out of occlusion as a control. Histologically, no bone necrosis was observed at the implant interface by any of the 8 implants for either period as a direct result of the 4-mm-diameter by 13-mm-length implant design. Clinical parameters did not differ among the implants; however, at 3 months, the immediately loaded implants demonstrated more than twice the amount of bone density at their surfaces compared to the unloaded implants of the same design. Future human clinical research would be necessary to provide a meaningful statistical analysis to validate the importance of this implant design and the function of osteocompression.     

The cost of dental implants as compared to that of conventional strategies

The effectiveness of dental implants is widely studied, especially in terms of their clinical outcomes. However, from the policymaker's point of view, variables other than safety and efficacy, such as the costs and effectiveness of dental implants as compared to other treatment alternatives, are vital in decision making. This paper compares the costs of different treatment strategies in a randomized clinical trial in patients with resorbed mandibles and persistent problems with their conventional dentures: treatment with a mandibular overdenture on permucosal dental implants, an overdenture on a transmandibular implant, new dentures after preprosthetic surgery, and new dentures only. Data were gathered on an individual patient level to gain insight into specific cost episodes. Direct costs were subdivided into labor, material, technique, and overhead. Data concerning these components were gathered during the consecutive treatment phases in the first year. Results show that the resources used to treat a patient with an overdenture supported by a transmandibular implant are seven times those of a complete new set of dentures. Comparison of the cost ratio of an implant-retained overdenture supported by permucosal implants and conventional new prostheses proves less unfavorable: 1:3. New dentures after preprosthetic surgery are almost as expensive as treatment with permucosal implants.     

Variability of hydroxyapatite-coated dental implants

Uniformity, surface roughness, and chemical phase structure are all important features of implant coatings. While the first two variables are important for implant placement, the phase structure affects implant fixation. This study examined the coating morphology and the amount, size, and distribution of crystalline regions of press-fit and screw-type dental implants. Implants obtained from five commercial vendors were sectioned sagittally, mounted, and polished to reveal the coating microstructure. The crystalline phase content varied depending on the implant supplier; however, general trends were observed. Amorphous regions were predominantly found at the metal interface and decreased toward the outside of the coating, producing a crystallinity graded coating. The distal end of the implant, where heat build-up was more likely during the coating procedure, displayed a higher crystalline content and larger crystalline regions. Similarly, the thread apex consisted of more of a crystalline phase. The results of this study of coating microstructure may be used to improve the quality and performance of implants and may help to explain different in vivo responses to the many available varieties of hydroxyapatite-coated dental implants.     

Dental implant outcomes in postmenopausal women undergoing hormone replacement

To determine if hormone supplementation reduces the risk of failure for osseointegration of dental implants in postmenopausal women, the treatment outcomes of 116 women older than age 50, treated with 450 endosseous dental implants, were analyzed in this retrospective study. The findings indicated that hormone replacement therapy may not be linked with improved outcomes of endosseous dental implant treatment in postmenopausal women. Smoking, however, appears to significantly increase the implant failure rate in the group observed in this study.     

Osteogenesis at the dental implant interface: high-voltage electron microscopic and conventional transmission electron microscopic observations

The osteogenesis of mandibular bone to endosteal dental implants was examined using an in vivo dog model. One half of the implants examined were unloaded implants, with the remaining one half prosthodontically loaded for 6 months. Undecalcified mandibular implant samples were examined with both high-voltage electron microscopy (HVEM) stereology and routine transmission electron microscopy. The osseous interface to integrated implants was shown to vary in its morphology. Mineralized bone was observed directly apposing the implant, often separated from the implant by an electron-dense deposit of approximately 50 nm. Within this densely mineralized matrix, osteocytes were routinely observed. Adjacent areas were shown to contain slightly wider zones of either a less dense mineralized matrix or, alternatively, unmineralized tissue. Other zones consisted of wider unmineralized matrices containing collagen fibers and osteoblasts. These latter zones were consistent with the appearance of an appositional type of bone growth. Because bone is a dynamic, actively remodeling tissue, a varied morphology of the support tissues to dental implant is not unexpected. Areas of mature bone interfacing with successfully integrated implants were demonstrated, as well as areas adjacent to the mature bone that were undergoing remodeling or mineralization. This study has also shown that HVEM stereology is a valuable research tool to investigate the oral tissue interface with dental implants.     

Fixed temporization and bone-augmented ridge stabilization with transitional implants

Utilization of dental implants in full-mouth restorations is now a well-accepted treatment modality, with numerous modifications and implant systems documented in the literature. The efficacy of the treatment procedure generally requires an extended postplacement healing period prior to loading the implant fixture with the stress of mastication. Until recently, clinicians have not been able to address patient comfort requirements during the healing period. The teaching objective of this article is to present and evaluate a transitional implant system used to provide function during the healing phase. The system consists of thin titanium transitional implants and a three-component overdenture that is intended to absorb the pressure during function and protect the augmented implant site and the definitive implant fixtures from the stress of immediate loading. Treatment objectives for the transitional and definitive implants are made during the initial treatment planning. Three cases are presented to document and illustrate the clinical procedure.     

Menopause: a new era

The Endopore implant provides a novel method for reliable fixation of endosseous dental implants within the bone. Through the use of a porous-surfaced zone formed by sintering Ti alloy particles of the appropriate size and under appropriate processing conditions to a sold Ti alloy core of desired shape (tapered truncated cone), an implant is now available that can be placed using a relatively simple surgical procedure using either surgical burs or hand osteotomes. Of even greater value is the suitability of this implant design for treatment of cases that because of minimal bone height cannot be treated routinely using other currently-available implants. The high success rates experienced with significantly shorter implant lengths compared with other designs indicate the appropriateness of this system for difficult-to-treat cases. The Endopore system represents the next generation of endosseous dental implants characterized by uncomplicated and reliable treatment for a wider range of dentally-compromised patients. Its history is founded on extensive and fully-documented research at the human preclinical stage as well as human use experiences. The results during the past nine years have confirmed the high expectations that those early studies suggested.     

Two-implant-supported single molar replacement: interdental space requirements and comparison to alternative options

Posterior single-tooth implant restorations are subjected to an increased risk of bending overload. A high incidence of implant fracture has been reported when using a single standard 3.75-mm-diameter implant to support a molar restoration. The purpose of this article is to demonstrate the clinical feasibility of placing two implants to support a molar restoration and to compare this treatment option to the use of a single standard implant or a wide-diameter implant. Two osseointegrated dental implants used to support a molar restoration in interdental spaces as small as 10 mm is shown to be effective and predictable in 60 restorations over the past 7 years. The use of two implants provides more surface area for osseointegration and spreads the occlusal loading forces out over a wider area, reducing the potential bending forces that would otherwise exist in a single-implant molar restoration.     

Acute liver failure

PURPOSE: This article reviews the literature on radiographic imaging techniques and image interpretation for dental implant treatment. MATERIALS AND METHODS: MEDLINE was used to identify published peer-reviewed literature for this report. RESULTS: Radiographic images are indispensable in the evaluation of osseous structures when planning treatment for dental implants. Potential bone sites for implant placement can be assessed clinically by means of palpation or probing through the mucosa; however, diagnostic imaging provides the best means for indirectly measuring bone dimensions. After healing of the implant site, the application of radiology is useful to verify the amount of bone adjacent to the implant and that the transmucosal abutments fit the implant. Upon completion of the implant prosthesis, radiology may be used to monitor initial and long-term success of implant treatment. CONCLUSION: Recommendations for the application of radiology over the course of treatment are made for various implant cases ranging from the overdenture to the single-tooth implant.     

An interactive, parallel, three-dimensional fast Fourier transform convolution dose calculation using a supercomputer

After cancer treatment in the head and neck area, mastication and speech are often affected. Some of the problems encountered can be solved by adequate dental rehabilitation. However, dental rehabilitation is often compromised for various reasons. The change in anatomy due to surgery often results in lack of denture-bearing mucosa. The effects of radiotherapy on the salivary glands and the mucosa result in dry oral tissue and diminished retention of removable dentures. Osseointegrated oral implants can help to solve these problems. Although implant treatment for patients with cancer of the head and neck is covered by the Dutch national health insurance, and there is therefore no financial obstacle, implants have not, so far, been widely used with these patients. In order to establish the possible reasons for this, an analysis was performed. Retrospective data on 95 consecutive patients were collected from records. The indication for the use of oral osseointegrated implants was reviewed. Analysis of the data showed that 45% did not need specific prosthetic rehabilitation. An indication for the use of osseointegrated implants was found in 25% of the patients. For various reasons, only 3% actually received implants. In striving to completely rehabilitate a cancer patient, the possible use of osseointegrated oral implants should be evaluated before the initial oncological treatment begins. The insertion of implants during the initial surgical procedure should be considered more often, with a view to reducing the number of surgical procedures.     

Reconstruction of an atrophic edentulous maxilla with unilateral cleft lip and palate (UCLP) using sub-antral augmentation and osseointegrated implants: case report and 3-year follow-up

With the current sophisticated, multidisciplinary approach to the treatment of cleft palate, it is anticipated that most patients with this deformity will enjoy good dental health and function. However, due to the number of older adults who were not treated with primary bone grafting and orthodontic therapy, there remains a significant number of potential candidates who may benefit from dental implants and implant-supported prostheses. Although it was not necessary in this case, a pharyngeal extension may be added to the maxillary denture to further improve speech and deglutition. This case report presents a three-year follow-up of a complex reconstruction of a highly compromised, edentulous patient. Stable fixation of the maxillary prosthesis results in a complete return to function in an individual for whom traditional dental prosthetics had resulted in ten years of failure and frustration. Combining the disciplines of reconstructive surgery and implant prosthetics enables the clinician to achieve a predictable result (Figures 12 and 13). While this case represents an extreme example, there are millions of patients for whom implant dentistry can provide life-changing benefits.     

Maintenance and treatment of the ailing and failing implant

Due to the pathologic nature of oral bacteria, the partially edentulous implant patient is at a greater risk than the fully edentulous. Peri-implantitis and/or retrograde peri-implantitis can result in ultimate loss of the implant fixture. It is important that the implant dentist understand the difference between the ailing implant, the failing implant, and the failed implant. This article discusses the pathologic diseases that affect dental implants and how to treat the "infected" implant (degranulation and detoxification) for titanium and hydroxylapatite-coated implants. Implant maintenance, including hand or motorized brushes, flosses, and oral rinses (chlorhexidine, 0.2%) will also be presented.     

The use of osteotomes for sinus augmentation at the time of implant placement

The placement of endosseous dental implants is often hampered by the loss of alveolar bone. In the posterior maxilla, the presence of the maxillary sinus and less-dense bone present additional obstacles to successful implant placement. Existing methods of subantral augmentation require extensive surgical manipulation, often including a second surgical site for harvesting autogenous bone. The development of surgical osteotomes has facilitated the placement of implants in areas of minimal alveolar bone height in the posterior maxilla. This article describes the osteotome technique for sinus augmentation at the time of implant placement and presents a short-term evaluation of 34 implants placed in 18 patients.     

Provisionalization of a combination implant/natural abutment restoration

This article describes a technique the dental technician can use to fabricate a long-term combination implant and natural tooth provisional prosthesis that will be used to evaluate esthetics and function. This provisional will act as an interim prosthesis while additional implants are healing.     

Educating a patient with dental implants

A functional dentition can be restored for edentulous and partially edentulous patients through the placement of dental implants. Dental assistants have a significant role in the education of implant patients so that meticulous oral self-care can be accomplished. Only through the combined team efforts of the dental office staff and patients themselves will the continued success of dental implantology be insured.