Synthesis and properties of ABA-type triblock copolymers of poly(glycolide-co-caprolactone) (A) and poly(ethylene glycol) (B)

Poly(glycolide-co-caprolactone) (A)-poly(ethylene glycol) (B) ABA-type triblock copolymers (PGCE) were synthesized by bulk ring opening polymerization, using the hydroxyl endgroups of poly(ethylene glycol) (PEG) as initiator and stannous octoate as catalyst. The resulting copolymers were characterized by various analytical techniques. Gel permeation chromatographic analysis indicated that the polymerization product was free of residual monomers, PEG and oligomers. ¹H NMR and differential scanning calorimeter results demonstrated that the copolymers had a structure of poly(glycolide-co-caprolactone) (PGC) chains chemically attached to PEG segments. All the PGCE copolymers showed improved hydrophilicity in comparison with the corresponding PGC copolymers with the same molar ratio of glycolidyl and caproyl units. The microspheres of PGCE copolymer exhibited rough surfaces quite different from the smooth surface of PGC microspheres. This phenomenon was attentively ascribed to the highly swollen ability of PGCE copolymers and the freeze-drying process in the microspheres fabrication.     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Synthesis of novel nanoreinforcements for polymer matrices by ATRP: Triblock poly(rotaxan)s based in polyethyleneglycol end-caped with poly(methyl methacrylate)

Poly(rotaxan)s of poly(ethylene glycol) and α-cyclodextrines (CD) block copolymers end-capped with poly(methyl methacrylate) chains were synthesized by atom transfer radical polymerization. The synthesized copolymers were characterized by ¹H NMR, 2D NOESY NMR, X-ray and Thermogravimetric analysis. Assuming a maximum relation of 2 CDs per ethyleneglycol unit, a coverage degree of 18% and 15% was achieved. X-ray analysis showed a characteristic signal around 20θ for all copolymers with an amorphous halo mainly due to inter-crystal poly(ethylene glycol) and poly(methyl methacrylate) chains. Full Molecular Dynamics of 20 ns was used to simulate the crystal structure of these copolymers. A pair correlation function was used to determine the coupling between hydrogen atoms of PEG, PMMA and cyclodextrine obtained by 2D NOESY NMR.     

Synthesis and characterization of complexes between poly(itaconic acid) and poly(ethylene glycol)

Summary Interpolymer complexes of poly(itaconic acid) and poly(ethylene glycol) (PIA/PEG) were prepared by two different procedures: simple mixing of preformed PIA and PEG and by polymerization of itaconic acid on poly(ethylene glycol) as a template. Complex formation was attributed to hydrogen bond formation between the carboxyl group of PIA and the ether group of PEG. The two types of complexes were characterized by viscometric measurements, thermogravimetric analysis (TGA), Fourier-transform infrared (FTIR) spectroscopy and adhesive force measurements. The results indicate that complexes prepared by template polymerization have a stronger hydrogen bonding and hence more ordered structure and better mucoadhesive properties.     

Synthesis of hydroxyl-capped comb-like poly(ethylene glycol) to develop shell cross-linkable micelles

A novel hydroxyl-capped comb-like poly[poly(ethylene glycol) methacrylate] (PPEGMA) was prepared via atom transfer radical polymerization (ATRP) of α-methylacryloyl-ω-hydroxyl-poly(ethylene glycol) at ambient temperature. The polymerization kinetics of the block copolymer was studied by gel permeation chromatography (GPC) and ¹H NMR. It is of interest to find the well-defined comb-like PEG can associate into micelles, which have hydrophilic PEG shell end-capped by hydroxyl groups. The hydroxyl in the shell were further cross-linked by divinyl sulfone (DVS), which could couple with two capped-end hydroxyl groups. The XPS, TEM, AFM and laser scattering particle size distribution analyzer results revealed that reactive micelles could be cross-linked by DVS. The reactive, cross-linkable micelles with PEG shell may have great potential as new drug carrier and nanoreactor, etc.     

Influence of the synthesis conditions on the structural and thermal properties of poly(l‐lactide)‐b‐poly(ethylene glycol)‐b‐poly(l‐lactide)

The poly(l ‐lactide)‐b‐poly(ethylene glycol)‐b‐poly(l ‐lactide) block copolymers (PLLA‐b‐PEG‐b‐PLLA) were synthesized in a toluene solution by the ring‐opening polymerization of 3,6‐dimethyl‐1,4‐dioxan‐2,5‐dione (LLA) with PEG as a macroinitiator or by transterification from the homopolymers [polylactide and PEG]. Two polymerization conditions were adopted: method A, which used an equimolar catalyst/initiator molar ratio (1–5 wt %), and method B, which used a catalyst content commonly reported in the literature (<0.05 wt %). Method A was more efficient in producing copolymers with a higher yield and monomer conversion, whereas method B resulted in a mixture of the copolymer and homopolymers. The copolymers achieved high molar masses and even presenting similar global compositions, the molar mass distribution and thermal properties depends on the polymerization method. For instance, the suppression of the PEG block crystallization was more noticeable for copolymer A. An experimental design was used to qualify the influence of the catalyst and homopolymer amounts on the transreactions. The catalyst concentration was shown to be the most important factor. Therefore, the effectiveness of method A to produce copolymers was partly due to the transreactions. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40419.     

Poly(ethylene glycol)-block-poly(butyl acrylate). I. Synthesis

Prepolymers of poly(ethylene oxide) (Pre-PEO) were synthesized by reacting azoisobutyronitrile (AIBN) with poly(ethylene glycol) (PEG), and their structures were characterized by IR and UV. The molecular weight of pre-PEO was related to the feed ratio and reaction time. These prepolymers can be used to prepare block copolymers—poly(ethylene oxide)-block-poly(butyl acrylate) (PEO-b-PBA) by radical polymerization in the presence of butyl acrylate (BA). Solution polymerization was a suitable technique for this step. The yield and the molecular weight of the product were related to the ratio of the prepolymer to BA, the reaction time, and temperature. GPC showed that the molecular weight increased with a higher ratio of BA to pre-PEO. The intrinsic viscosity of the copolymers was only slightly dependent on reaction time, but decreased at higher reaction temperatures, as did the amount of PBA homopolymer. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:1667–1674, 1997     

Synthesis of monomethoxy poly(ethylene glycol) without diol poly(ethylene glycol)

Since monomethoxy poly(ethylene glycol) (mPEG) inevitably contains diol PEG and is difficult to get high molecular weight through traditional synthesis at high temperature under high pressure, a novel synthetic technique via anionic solution polymerization was reported in this study. With a new initiating system, potassium naphthalene and methanol, was introduced, the polymerization proceeded at ambient temperature and side reactions were well restrained. Furthermore, a slight excess of potassium naphthalene can effectively remove the trace of water and oxygen in the reaction system. Under this condition, mPEG was nearly quantitatively obtained without containing diol PEG. Its Mn ranged from 1 to 30 kDa and the polydispersity was kept lower than 1.07. Characterization of the mPEG obtained was carried out using GPC to determine the content of diol PEG and ¹H‐NMR and MALDI‐ToF MS spectroscopic analysis to confirm the exact structure. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Controlled synthesis and characterizations of amphiphilic poly[(R,S)-3-hydroxybutyrate]-poly(ethylene glycol)-poly[(R,S)-3-hydroxybutyrate] triblock copolymers

Well-defined biodegradable amphiphilic triblock copolymers consisting of atactic poly[(R,S)-3-hydroxybutyrate] (PHB) and poly(ethylene glycol) (PEG) as the side hydrophobic block and middle hydrophilic block were synthesized via ring opening polymerization of (R,S)-β-butyrolactone from PEG macroinitiators and characterized using NMR, GPC, FT-IR, XRD, DSC and TG analyses. The controlled synthesis was made possible by the facile synthesis of pure PEG macroinitiators through a TEMPO-mediated oxidation. Constituting 40-70 wt% of the copolymer content, PHB blocks grown were amorphous while PEG formed crystalline phase when segment was sufficiently long. While hindering PEG crystallization, atactic PHB mixed well with amorphous PEG to give single T_g in all the copolymers. The copolymers exhibited two-step thermal degradation profile starting with PHB degradation from 210 to 300 °C, then PEG from 350 to 450 °C.     

聚乙二醇存在下苯乙烯/甲基丙烯酸甲酯无皂乳液聚合体系的动态表面张力

利用最大泡压法（MBPM）研究了苯乙烯（St）/甲基丙烯酸甲酯（MMA）在有、无聚乙二醇（PEG）水溶液中进行无皂乳液聚合过程中的动态表面张力变化。发现PEG使体系反应速率变慢,反应50 min,有PEG参与的体系转化率只有49%,而无PEG参与的体系转化率已达到98%以上,接近终点。St/MMA和引发剂形成的聚合物在PEG的作用下,形成了一种具有更强表面活性的聚合物,表面活性水平高于PEG以及无PEG参与聚合体系的聚合物,但弱于混合单体及齐聚物。这种较强表面活性的聚合物在转化率只有5%的时候就已经存在,是聚合物进入粒子堆形成稳定小粒子的动力,并最终使粒子带有足够脱离粒子堆的表面电荷。     

Preparation and characterization of poly(trimethylene terephthalate)‐poly(ethylene oxide terephthalate) segmented copolymer/multiwalled carbon nanotubes composites by in situ polymerization

Poly(trimethylene terephthalate)‐poly(ethylene oxide terephthalate) block copolymer (PTG)/multiwalled carbon nanotubes (MWCNTs) composites were prepared via in situ polymerization. To improve the dispersion of MWCNTs in the PTG matrix, the poly(ethylene glycol)‐grafted multiwalled carbon nanotubes (MWCNT‐PEG) were produced by the “graft to” method. The transmission electron microscopy observation demonstrated that a homogeneous dispersion of MWCNT‐PEG was obtained. As a consequence, the percolation threshold for the rheology was around 0.5 wt% and the conductivity was ～1 wt%, respectively. Differential scanning calorimetry and polarized optical microscopy results confirmed that MWCNT‐PEG can act as an effective heterogeneous nucleating agent. Interestingly, the effects of MWCNT‐PEG on crystallization and melting of the poly(ethylene oxide terephthalate) blocks were more pronounced than on those of the PTT blocks. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Synthesis of polylactide/poly(ethylene glycol) diblock copolymers with functional endgroups

Amphiphilic polylactide/poly(ethylene glycol) (PLA–PEG) diblock copolymers with functional groups at the PEG chain ends were synthesized by coupling PLA and PEG homopolymers using different coupling agents. PLA precursors with different endgroups were synthesized by ring‐opening polymerization of l ‐lactide in the presence of different initiators such as octanol, acetic acid or benzoic acid, or water, using non‐toxic zinc lactate as catalyst. The mechanism of the ring‐opening polymerization of lactide initiated by carboxyl groups was investigated and discussed in comparison with the literature. N,N'‐carbonyldiimidazole was used to couple the two hydroxyl groups of PLA and PEG, using 4‐dimethylaminopyridine (DMAP) as catalyst. Dicyclohexylcarbodiimide (DCC) and DMAP were adopted to couple the carboxyl group and the hydroxyl group of PLA and PEG, respectively, while DCC and N‐hydroxysuccinimide were used to connect PLA and PEG by coupling their carboxyl and amine groups. Comparison of different coupling routes shows that the DCC/DMAP one exhibits the highest efficiency. A common tumor targeting ligand, folic acid, was attached to PLA–PEG with hydroxyl endgroups using the DCC/DMAP route. The resulting PLA–PEG copolymers bearing folic acid present great interest for targeted delivery of anti‐cancer drugs. © 2012 Society of Chemical Industry     

Synthesis and characterization of amine‐functionalized amphiphilic block copolymers based on poly(ethylene glycol) and poly(caprolactone)

A series of amine‐functionalized block copolymers, poly(caprolactone)‐block‐poly(ethylene glycol) (PCL‐b‐PEG), were synthesized by ring‐opening bulk polymerization (ROP) of ε‐caprolactone (ε‐CL) initiated through the hydroxyl end of the amino poly(ethylene glycol) (PEG) used as a macroinitiator in the presence of stannous 2‐ethylhexonoate [Sn(Oct)₂]. The polymerization and end functionality of the polymer were studied by different physicochemical techniques (¹H NMR, Fourier transform infrared and X‐ray photoelectron spectroscopy, gel permeation chromatography and thermogravimetric analysis). Thermal, crystalline and mechanical properties of the polymer were thoroughly analyzed using differential scanning calorimetry, wide‐angle X‐ray diffractometry and tensile testing, respectively. The results showed a linear improvement in crystallinity and mechanical properties of the polymer with the content of PEG. Thus the synthesized functional polymers can be used as excellent biomaterials for the delivery of polyanions, as well as macroinitiators for the synthesis of A–B–C‐type block copolymers. Copyright © 2006 Society of Chemical Industry     

Synthesis and properties of novel biodegradable triblock copolymers of poly(5-methyl-5-methoxycarbonyl-1,3-dioxan-2-one) and poly(ethylene glycol)

Novel biodegradable triblock copolymers of poly(5-methyl-5-methoxycarbonyl-1,3-dioxan-2-one) (PMMTC) with poly(ethylene glycol) (PEG), PMMTC-b-PEG-b-PMMTC, were synthesized by the ring-opening polymerization of MMTC in bulk, using the dihydroxyl PEG as initiator and Sn(Oct)₂ as catalyst. The triblock copolymers with different compositions were characterized by IR and ¹H NMR, their molecular weight was measured by gel permeation chromatography (GPC). The results showed that the molecular weight of triblock copolymers increased either with the increase of the molar ratio of MMTC in feed while the PEG chain length kept constant, or by lengthening the backbone chain of PEG block with the same ratio of MMTC in feed. The hydrophilicity of copolymers was greatly improved by incorporation of PEG block into polycarbonate. The in vitro hydrolytic/enzymatic degradation and controlled drug release properties of the triblock copolymers were also investigated.     

Synthesis of ultrahigh molecular weight phenolic polymers by enzymatic polymerization in the presence of amphiphilic triblock copolymer in water

An enzymatic oxidative polymerization of phenols was investigated in the presence of poly(ethylene glycol) (PEG)-poly(propylene glycol) (PPG)-poly(ethylene glycol) (PEG) triblock copolymer (Pluronic) in water. The formation of micellar aggregate of phenol and Pluronic by hydrogen bonding interaction in an aqueous solution was verified by DLS measurement. The PEG content of Pluronic greatly affected the polymerization behaviors. Using Pluronic with high PEG content improved the regioselectivity of the polymerization of phenol to give the polymer mainly consisting of phenylene unit. The polymerization in the presence of Pluronic F68 (EG₇₆-PG₂₉-EG₇₆) produced the phenolic polymer with ultrahigh molecular weight (M_w > 10⁶). From other phenols, high molecular weight polymers were also obtained. In addition, the FT-IR, DSC, and XRD analyses exhibited the formation of miscible complex between the phenolic polymer and Pluronic by hydrogen bonding interaction.     

Synthesis and Characterization of Poly(ethylene glycol) grafted Poly(ε-Caprolactone)

Summary A new graft copolymer, poly(ε-caprolactone) (PCL) grafted with poly(ethylene glycol) (PEG), was prepared by one-pot synthesis of ε-caprolactone and modified PEG. Aluminium isopropoxide or potassium tert-butoxide was used as a catalyst for the ring-opening polymerization. Polymerization using potassium tert-butoxide as a catalyst showed very effective graft reaction of PEG onto poly(ε-caprolactone). A slight decrease in the melting temperature was observed with the increase of the PEG graft frequency. Interestingly, considerable changes were observed on the surface property by the introducing PEG side chains compared to that of PCL homopolymer. Measurements of water contact angle showed that the hydrophilic surface of the polymer could be obtained even at a low graft frequency of PEG.     

A mucoadhesive polymer prepared by template polymerization of acrylic acid in the presence of poly(ethylene glycol) macromer

A new mucoadhesive polymer complex was prepared by the template polymerization of acrylic acid with poly(ethylene glycol) macromer (PEGM) as a template polymer. Fourier transform infrared results showed that the poly(acrylic acid) (PAA)/PEGM mucoadhesive polymer complex was formed by hydrogen bonding between the carboxyl groups of PAA and the ether groups of PEGM. The glass‐transition temperature of the PAA/PEGM mucoadhesive polymer complexes was shifted to a lower temperature as the repeating unit ratio of PAA/PEGM in the complex decreased. The dissolution rate of the PAA/PEGM mucoadhesive polymer complex was much slower than that of the PAA/poly(ethylene glycol) (PEG) mucoadhesive polymer complex and was dependent on the pH and molecular weight of PEGM. The mucoadhesive force of the PAA/PEGM mucoadhesive polymer complexes was stronger than that of commercial Carbopol 971P NF and almost the same as that of the PAA/PEG mucoadhesive polymer complex. The PAA/PEGM interpolymer complex seemed to be a better mucoadhesive polymer matrix than the PAA/PEG interpolymer complex. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1904–1910, 2002     

种子聚合法制备PS/PAA核壳微球的研究

设计制备了以疏水性聚苯乙烯(PS)为核、以亲水性聚丙烯酸(PAA)为壳的PS/PAA核壳结构复合微球。首先利用无皂乳液聚合法制备了亚微米级的PS微球,再以其为种子,利用种子无皂乳液聚合法制备PS/PAA核壳微球。在种子聚合阶段,选用AIBN当引发剂,经过红外光谱(IR)表征,表明当使用油溶性引发剂偶氮二异丁腈(AIBN),使其最终形成PS/PAA核壳结构微球。这种方法解决了亲水性较强的单体在以水为介质时在PS微球溶于少量的苯乙烯(St),并在引发聚合之前经过充分的吸附溶胀,可使亲水性单体AAc在PS种子微球表面聚合生成壳层,解决表面不容易直接聚合生成壳层的问题。     

聚醚二醇钾盐引发D．L－丙交酯的开环聚合研究

以聚乙二醇－４０００钾盐为引发剂．合成了食不同长度聚醚链段的聚Ｄ．Ｌ－乳酸－聚乙二醇－聚Ｄ．Ｌ－乳酸（ＰＬＡ－ＰＥＧ－ＰＬＡ）三嵌段共聚物。考察了溶剂用量、引发剂用量、反应温度和时间、ＰＥＧ分子量、不同溶剂对聚合反应的影响。以１Ｈ－ＮＭＲ、ＩＲ、ＤＳＣ、ＧＰＣ对共聚物进行了表征。     

PMMA/PEG共混物形态和热性质的研究

在聚乙二醇存在的情况下,自由基聚合得到的聚甲基丙烯酸甲酯/聚乙二醇(PMMA/PEG)共混物,是一种半结晶聚合物;有相分离发生,一部分PEG晶体依然保持其晶体的特征,另一部分PEG晶体转变成非晶态,与PMMA网络复合,形成完全均一的非晶相。