Design of small and low-profile antenna for satellite digital audio radio system

The design and optimisation of a small and low-profile antenna for the satellite digital audio radio system using a nondominated sorting genetic algorithm is presented. A fairly omnidirectional elevation gain pattern over -60/spl deg/相似文献   

Disc-loaded monopole antenna array for switched beam control

Switched beam control is demonstrated using a disc-loaded monopole antenna on a finite ground plane with four parasitic elements. The beam direction can be switched by open circuiting one of the parasites. The array antenna gives a gain of 5.1 dBi at 2.45 GHz, which is more than three times that of a single element. The input return loss bandwidth is 24% and the radiated beam is elevated above the ground plane by about 500. The measured results show good agreement with simulations.     

A novel approach for miniaturization of slot antennas

With the virtual enforcement of the required boundary condition (BC) at the end of a slot antenna, the area occupied by the resonant antenna can be reduced. To achieve the required virtual BC, the two short circuits at the end of the resonant slot are replaced by some reactive BC, including inductive or capacitive loadings. The application of these loads is shown to reduce the size of the resonant slot antenna for a given resonant frequency without imposing any stringent condition on the impedance matching of the antenna. A procedure for designing this class of slot antennas for any arbitrary size is presented. The procedure is based on an equivalent circuit model for the antenna and its feed structure. The corresponding equivalent circuit parameters are extracted using a full-wave forward model in conjunction with a genetic algorithm optimizer. These parameters are employed to find a proper matching network so that a perfect match to a 50 /spl Omega/ line is obtained. For a prototype slot antenna with approximate dimensions of 0.05/spl lambda//sub 0//spl times/0.05/spl lambda//sub 0/ the impedance match is obtained, with a fairly high gain of -3dBi, for a very small ground plane (/spl ap/0.20/spl lambda//sub 0/). Since there are neither polarization nor mismatch losses, the antenna efficiency is limited only by the dielectric and ohmic losses.     

Seven-element ground skirt monopole ESPAR antenna design from a genetic algorithm and the finite element method

The design of an optimized electronically steerable passive array radiator (ESPAR) antenna is presented. A genetic algorithm using a finite element based cost function optimized the antenna's structure and loading conditions for maximal main lobe gain in a single azimuth direction. Simulated gain results of 7.3 dBi at 2.4 GHz were attained along the antenna's elemental axis. The optimized antenna was fabricated and tested with the corresponding experimental gain better than 8 dBi. The 0.7 dB error between simulated and measured gain was constant for numerous structures and therefore did not affect the optimization. The optimized antenna reduced average main lobe elevation by 15.3/spl deg/ to just 9.7/spl deg/ above the horizontal.     

Elliptical planar monopole antenna with extremely wide bandwidth

A planar monopole antenna with an extremely wide bandwidth is introduced, which is composed of an elliptical monopole patch and a trapeziform ground plane, both printed on the same side of a substrate, and is fed by a tapered CPW feeder in the middle of the ground plane. The simulated and experimental results demonstrate that this antenna achieves a ratio impedance bandwidth of 21.6:1 for VSWR/spl les/2, and exhibits a nearly omnidirectional radiation pattern, while its area is only about 0.19/spl lambda//sub l//spl times/0.16/spl lambda//sub l/ where /spl lambda//sub l/ is the wavelength of the lowest operating frequency.     

Dual-band circularly polarized equilateral triangular-patch array antenna for mobile satellite communications

The Japan Aerospace Exploration Agency will launch the Engineering Test Satellite VIII (ETS-VIII) in 2006 to support the next generation of mobile satellite communications covering the area of Japan (beam coverage El=38/spl deg/ to 58/spl deg/). In this paper, a satellite-tracking left-handed circularly polarized triangular-patch array antenna is developed for ground applications. The targeted minimum gain of the antenna is set to 5 dBic at the central elevation angle (El=48/spl deg/), in the Tokyo area, for applications using data transfer of around a hundred kbps. The antenna is composed of three equilateral triangular patches for both reception and transmission units operating at 2.50 and 2.65 GHz frequency bands, respectively. The antenna was simulated by method of moments (MoM) analysis, and measurement of the fabricated antenna was performed to confirm the simulation results. The measurement results show that the frequency characteristics and the 5-dBic gain coverage in the conical-cut plane of the fabricated antenna satisfy the specifications for ETS-VIII. A prototype of the proposed antenna system is employed in outdoor experiments using a pseudosatellite and shows good performance from El=38/spl deg/ to 58/spl deg/.     

Design of an efficient miniaturized UHF planar antenna

The design aspects and the measured results of a novel miniaturized planar antenna are described. Such architectural antenna design is of great importance in mobile military communications where low visibility and high mobility are required. Slot radiating elements, having a planar geometry and capable of transmitting vertical polarization when placed nearly horizontal, are appropriate for the applications at hand. Slot antennas also have another useful property, so far as impedance matching is concerned. Basically, slot dipoles can easily be excited by a microstrip line and can be matched to arbitrary line impedances simply by moving the feed point along the slot. Antenna miniaturization can be achieved by using a high permittivity or permeability substrate and superstrate materials and/or using an appropriate antenna topology. We demonstrate miniaturization by designing an appropriate geometry for a resonant narrow slot antenna. A very efficient radiating element that occupies an area as small as 0.12/spl lambda//sub 0//spl times/0.12/spl lambda//sub 0/ is designed and tested. Simulation results, as well as the measured input impedance and radiation patterns of this antenna, are presented. This structure shows a measured gain of 0.5 dBi on FR4 substrate, which has a loss-tangent of the order of 0.01. Also, the effect of finite ground plane size on gain and resonant frequency is investigated experimentally.     

Composite right/left-handed transmission line based compact resonant antennas for RF module integration

Several electrically small resonant antennas employing the composite right/left-handed transmission line (CRLH-TL) are presented for integration with portable RF modules. The proposed antenna designs are based on the unique property of anti-parallel phase and group velocity of the CRLH-TL at its fundamental mode. In this mode, the propagation constant increases as the frequency decreases, therefore, a small guided wavelength can be obtained at a lower frequency to provide the small /spl lambda//sub g//2 resonant length used to realize a compact antenna design. Furthermore, the physical size and the operational frequency of the antenna depend on the unit cell size and the equivalent transmission line model parameters of the CRLH-TL, including series inductance, series capacitance, shunt inductance and shunt capacitance. Optimization of these parameters as well as miniaturization techniques of the physical size of unit cell is investigated. A four unit-cell resonant antenna is designed and tested at 1.06 GHz. The length, width and height of the proposed antenna are 1/19/spl lambda//sub 0/, 1/23/spl lambda//sub 0/ and 1/83/spl lambda//sub 0/, respectively. In addition, a compact antenna using a 2-D three by three mushroom like unit cell arrangement is developed at 1.17 GHz, showing that an increased gain of 0.6 dB and higher radiation efficiency can be achieved over the first prototype antenna. The same design is applied in the development of a circularly polarized antenna operating at 2.46 GHz. A 116/spl deg/ beamwidth with axial ratio better than 3 dB is observed. The physical size of the proposed mushroom type small antenna and the circularly polarized antenna is 1/14/spl lambda//sub 0/ by 1/14/spl lambda//sub 0/ by 1/39/spl lambda//sub 0/ and 1/10/spl lambda//sub 0/ by 1/10/spl lambda//sub 0/ by 1/36/spl lambda//sub 0/, respectively.     

A 60-GHz multilayer parasitic microstrip array antenna on LTCC substrate for system-on-package

This letter describes a compact and high-gain multilayer parasitic microstrip array antenna (MPMAA). The design and performance of the proposed array antenna are presented. The antenna employs three layers with a 2/spl times/2 parasitic array on each layer. The developed prototype MPMAA employs a multilayer low-temperature co-fired ceramic (LTCC) substrate that is well suited to the assembly of MMIC chips. The fabricated MPMAA achieves a 7.17 dBi absolute gain at 60 GHz including the loss derived from the feeding parts and RF probe to measure its antenna performance. The spacing of the top layer of the parasitic array constructed by 2/spl times/2 elements has a free-space wavelength of 0.36 and the chip size is 10 mm/sup 2/. The fabricated MPMAA achieves both compact and high directional gain and satisfies the requirements for a millimeter-wave system-on-package (SOP).     

Dual-band six-element switched parasitic array for smart antennacellular communications systems

Simulation results for a dual-band switched parasitic smart antenna array designed for cellular communications systems are presented. The array consists of six loaded monopole elements on an infinite ground plane and offers five switched directions equally spaced through 360°. At 900 and 1900 MHz, the 10 dB bandwidths are 15 and 13%, respectively. The antenna covers the azimuth plane with a maximum gain of 4 dBi and a minimum gain of 2 dBi. The front-to-back ratios of the radiation patterns are better than -15 dB. The design is robust in terms of manufacturing and environmental tolerances     

Investigations on miniaturized endfire vertically polarized quasi-fractal log-periodic zigzag antenna

This paper presents the investigations on a miniaturized vertically polarized traveling wave antenna for operation in the high frequency band (3-6 MHz), with a specific requirement of keeping its height near 1/8th of a wavelength. The antenna is desired to have a good endfire gain and front to back ratio, and small radiation levels in the vertical direction at broadside angle. A log-periodic Zigzag antenna (LPZA) has acceptable performance in both gain and polarization. Its height however is large, at about one wavelength (1/spl lambda//sub L/). The concept of fractal antenna is employed in this antenna to achieve the necessary height reduction to /spl lambda//sub L//8, while keeping its radiation characteristics nearly constant. Both single and dual arm quasifractal log-periodic zigzag antenna (QFLPZA) configurations are investigated, with a maximum antenna height of only 1/8th of a wavelength, showing the desired radiation characteristics, and a wide impedance bandwidth of 67%. This type of antenna may find applications in surveillance radar.     

Analysis of the small band-rejected antenna with the parasitic strip for UWB

A novel band-rejected ultrawideband antenna with one parasitic strip is presented in this paper. It is designed to work on a substrate FR4 that has a thickness of 1 mm and relative permittivity of 4.6, and to operate from 3 to 17 GHz. The proposed antenna is fed by microstrip line and utilizes the parasitic strip to reject the frequency band (5.15-5.825 GHz) limited by IEEE 802.11a and HIPERLAN/2. The size of the antenna is 20/spl times/20 mm/sup 2/ and this antenna has good radiation characteristics. Effects of varying the location and length of the parasitic strip and the structure of the ground and monopole patch on the antenna performance have also been studied.     

Peano分形加载单极子辐射性能的研究

对有限地板尺寸和介质填充情况下Peano分形加载单极子天线的辐射特性进行了研究.利用HFSS分析了地板尺寸和填充介质材料对天线反射系数、辐射方向图和增益的影响.仿真表明:随着地板尺寸的减小,天线的阻抗带宽和增益明显减小,H面方向图变化不大,而E面方向图的半功率波束宽度增大,波束仰角减小;填充材料的介电常数过大会导致天线性能的恶化.在分析研究的基础上,设计并研制了地板尺寸为220mm×220mm的一阶和二阶Peano分形加载单极子天线.天线分别实现了45°和36°的波束仰角,50°和45°的半功率波束宽度.仿真与实测结果均表明凋节地板尺寸是控制Peano分形加载单极子天线E面半功率波束宽度和波束仰角的一种简单而有效的方法.     

Printed figure-of-eight wire antenna for circular polarization

A new printed wire antenna with circular polarization properties is presented. The geometry of the printed wire which takes the form of a figure-of-eight has a total length of 1.3/spl lambda//sub o/ and serves as a nonresonant traveling-wave antenna. It is shown that a 3-dB axial ratio bandwidth of 15% can be achieved. The half-power and 3-dB axial ratio beamwidth is approximately /spl plusmn/45/spl deg/, while its gain is of the order of 6.5 dB.     

Accordion shape monofilar axial mode helix for RFID reader

An accordion shape monofilar axial mode helical antenna designed by curving the helix along the axis is proposed. This antenna achieves a low-profile characteristic as the 10-turn helix's axial length is 0.354/spl lambda/. The impedance bandwidth (SWR<1.5) is 9% from the frequency of 880 to 963 MHz and the axial ratio bandwidth (AR<3 dB) is 6.5%. The measured gain is 10.2 dBi. This antenna operated at the centre frequency of 915 MHz and has a tilted radiation of 17/spl deg/ to the curving side.     

Passive parasitic UWB antenna capable of switched beam‐forming in the WLAN frequency band using an optimal reactance load algorithm

We propose a switched beam‐forming antenna that satisfies not only ultra‐wideband characteristics but also beam‐forming in the WLAN frequency band using an ultra‐wideband antenna and passive parasitic elements applying a broadband optimal reactance load algorithm. We design a power and phase estimation function and an error correction function by re‐analyzing and normalizing all the components of the parasitic array using control system engineering. The proposed antenna is compared with an antenna with a pin diode and reactance load value, respectively. The pin diode is located between the passive parasitic elements and ground plane. An antenna beam can be formed in eight directions according to the pin diode ON (reflector)/OFF (director) state. The antenna with a reactance load value achieves a better VSWR and gain than the antenna with a pin diode. We confirm that a beam is formed in eight directions owing to the RF switch operation, and the measured peak gain is 7 dBi at 2.45 GHz and 10 dBi at 5.8 GHz.     

Small dual C-slot printed antenna

A novel shorted dual C-slot printed antenna is presented. The antenna consists of two C-shaped slots embedded within the shorted patch antenna to maximise the current path of the antenna. A 10 dB return loss bandwidth of 5.4% has been achieved. The overall dimension of the antenna is 0.11/spl lambda//sub 0//spl times/0.074/spl lambda//sub 0//spl times/0.074/spl lambda//sub 0/ and is suitable for application where limited space is a premium. Importantly, the antenna is easy to develop.     

Investigation of wide-band microstrip slot antenna

This paper presents the simulation and experimental investigations of a printed microstrip slot antenna. It is a quarter wavelength monopole slot cut in the finite ground plane edge, and fed electromagnetically by a microstrip transmission line. It provides a wide impedance bandwidth adjustable by variation of its parameters, such as the relative permittivity and thickness of the substrate, width, and location of the slot in the ground plane, and feed and ground plane dimensions. The ground plane is small, 50 mm/spl times/80 mm, and is about the size of a typical PC wireless card. At the center frequency of 3.00 GHz, its width of 50 mm is about /spl lambda//2 and influences the slot impedance and bandwidth significantly. An impedance bandwidth (S/sub 11/=-10 dB) of up to about 60% is achieved by individually optimizing its parameters. The simulation results are confirmed experimentally. A dual complementary slot antenna configuration is also investigated for the polarization diversity.     

Broadband planar antenna with parasitic radiator

A novel kind of planar monopole broadband antenna with a parasitic radiator is presented. Measurements show that the bandwidth of the monopole antenna has been considerably improved with a parasitic element earthed with a matching inductor. The achieved impedance bandwidth reaches over 85% for VSWR/spl les/2, and the measured radiation patterns have little distortion when the frequency changes. The impedance bandwidth parameters are compared for different dimensions of ground planes     

Electronic beam steering using switched parasitic patch elements

A new technique is presented demonstrating the use of switched parasitic elements in electronic beam steering applications. Experimental and theoretical results are presented for a linearly polarised five element steerable patch antenna array operating at 1.55 GHz. Shorted parasitic elements have been used to steer the beam in two directions for tracking polar orbiting satellites. The minimum gain of the system for elevation angles >20° above the horizon is -1.5 dBi in the forward direction