Characteristics of Bi4Ti3O12 thin films on ITO/glass and Pt/Si substrates prepared by R.F. sputtering and rapid thermal annealing

Bi₄Ti₃O₁₂ thin films are deposited on ITO/glass and Pt/Ti/Si(100) substrates by R.F. magnetron sputtering at room temperature. The films are then heated by a rapid thermal annealing (RTA) process conducted in oxygen atmosphere at temperatures ranging from 550–700^∘C. X-ray diffraction examination reveals that the crystalinity of the films grown on Pt/Ti/Si is better than that of the films grown on ITO/glass under the same fabrication conditions. SEM observation shows that the films grown on Pt/Ti/Si are denser than those grown on ITO/glass substrates. Interactive diffusion between the Bi₄Ti₃O₁₂ film and the ITO film increases with the increase of annealing temperature. The optical transmittance of the thin film annealed at 650^∘C is found to be almost 100% when the effect of the ITO film is excluded. The relative dielectric constants, leakage currents and polarization characteristics of the two films are compared and discussed.     

Synthesis and properties of ferroelectric Si-doped (Bi, Nd)4Ti3O12 thin films by chemical solution deposition

Ferroelectric Si-doped (Bi,Nd)₄Ti₃O₁₂ thin films have been prepared on Pt/TiO_x/SiO₂/Si substrates through metal-organic compounds by the chemical solution deposition. The Bi_3.25Nd_0.75Ti_2.9Si_0.1O₁₂ (BNTS) precursor films were found to crystallize into the Bi-layered perovskite Bi₄Ti₃O₁₂ single-phase above 600^∘C. The synthesized BNTS films revealed a random orientation having a strong 117 reflection. The BNTS thin films prepared between 600^∘C and 700^∘C showed well-saturated P-E hysteresis loops with P _r of 13–14 μ C/cm² and E _c of 100–110 kV/cm at an applied voltage of 5 V. The surface roughness of the BNTS thin films was improved by Si doping compared with that of undoped Bi_3.35Nd_0.75Ti₃O₁₂ films.     

Preparation and electrical properties of 0.4Pb(Zn1/3Nb2/3)O3-0.6Pb(Zr0.4Ti0.6)O3 thin films by 2-step annealing method

Films of (1−x)Pb(Zn_1/3Nb_2/3)O₃-xPb(Zr_0.4Ti_0.6) O₃ (x = 0.6, 40PZN-60PZT) were deposited on Pt/TiO₂/ SiO₂/Si substrate through spin coating. Using a combination of homogeneous precursor solution preparation and two-step pyrolysis process, we were able to obtain the 40PZN-60PZT thin films of perovskite phase virtually without pyrochlore phase precipitation after annealing above 650^∘C. But since annealing done at the high temperatures for extended time can cause diffusion of Pt, TiO₂ and Si, and precipitation of nonstoichiometric PbO, we adopted 2-step annealing method to circumvent these problems. The 2-step annealed films show dense microstructure than the 1-step films annealed at higher temperature. Furthermore, the root-mean-square surface roughness of 220 nm thick films which are annealed at 720^∘C for 1 min and then annealed at 650^∘C for 5 min was found to be 3.9 nm by atomic force microscopy as compared to the 12 nm surface roughness of the film annealed only at 720^∘C for 5 min. The electrical properties of 2-step annealed films are virtually same and those of the 1-step annealed films annealed at high temperature. The film 2-step annealed at 720^∘C for brief 1 min and with subsequent annealing at 650^∘C for 5 min showed a saturated hysteresis loop at an applied voltage of 5 V with remanent polarization (P _r) and coercive voltage (V _c) of 25.3 μC/cm² and 0.66 V respectively. The leakage current density was lower than 10⁻⁵A/cm² at an applied voltage of 5 V.     

Dielectric properties of ZnNb2 O 6 -TiO 2 mixture thin films

ZnNb₂O₆-TiO₂ mixture thin films with multilayer structures were fabricated via a sol-gel spin coating process. TiO₂ layers were deposited on the pre-crystallized ZnNb₂O₆ layers in order to suppress the formation of the ixiolite phase which always forms in the bulk system. The phase constitution of the thin films, confirmed by X-ray diffraction (XRD), could be controlled by the annealing temperatures, which, in turn, influenced the dielectric properties of the thin films. TiO₂ layers crystallized as the anatase phase and then transformed to the rutile phase at temperatures higher than 725^∘C. Dielectric constants of the mixture thin films, measured at 1 MHz with an MIM (metal-insulator-metal) structure, increased from 27 to 41 with dielectric losses below 0.005 as the annealing temperature increased from 700^∘C to 900^∘C. The increase in the dielectric constants was understood to originate from the increasing amounts of the rutile phase. Temperature coefficients of capacitance (TCC) were also measured between 25^∘C and 125^∘C, which showed a decreasing manner from positive values to negative values with increasing annealing temperatures. When annealed at 850^∘C, the TCC of the thin films could be tuned to be approximately 0 ppm/^oC with dielectric constant and dielectric loss of 36 and 0.002, respectively.     

Structure and dielectric properties of BaTi4O9 thin films for RF-MIM capacitor applications

BaTi₄O₉ thin films were grown on a Pt/Ti/SiO₂/Si substrate using RF magnetron sputtering. A homogeneous BaTi₄O₉ crystalline phase developed in the films deposited at 550^∘C and annealed above 850^∘C. When the thickness of the film was reduced, the capacitance density and leakage current density increased. Furthermore, the dielectric constant was observed to decrease with decreasing film thickness. The BaTi₄O₉ film with a thickness of 62 nm exhibited excellent dielectric and electrical properties, with a capacitance density of 4.612 fF/μm² and a dissipation factor of 0.26% at 100 kHz. Similar results were also obtained in the RF frequency range (1–6 GHz). A low leakage current density of 1.0 × 10⁻⁹ A/cm² was achieved at ± 2 V, as well as small voltage and temperature coefficients of capacitance of 40.05 ppm/V² and –92.157 ppm/^∘C, respectively, at 100 kHz.     

Hydrothermal growth of BaTiO3 thin films on printed circuit boards for integral capacitor applications

Polycrystalline BaTiO₃ films were hydrothermally grown on Ti-coated substrates from 80^∘C to 200^∘C. Films grown at 200^∘C exhibited the lowest dielectric loss of around 0.1. Proton incorporation was more severe for the 80^∘C film resulting in higher dielectric losses and leakage currents about two orders of magnitude higher. Post deposition oxygen plasma treatment removed incorporated protons and reduced the loss tangent but did not reduce defect density. As such, the leakage current of the 80^∘C film remained high. The films had dielectric constants of 275 to 675 from 100 Hz to 100 kHz and a value of 67 from 100 MHz to 3 GHz.     

Calculation of the intrinsic dead layers thicknesses from Au/Ba0.5Sr0.5TiO3/Pt thin film capacitors

Ferroelectric Ba_0.5Sr_0.5TiO₃ (BST) films were prepared on Pt/Ti/SiO₂/Si substrates by the sol-gel process. The films were spin-coated at 2000 rpm for 30 secs and then pyrolysed for 5 mins at the temperature of 350^∘C. This coating procedure was repeated for 3, 4, 5 and 6 times to obtain BST films with different thicknesses. After coating the films with the desired repetition times, the films were finally annealed in a conventional furnace at temperatures ranging from 600^∘C to 800^∘C with a 50^∘C interval in between. The films obtained with an annealing procedure of 750^∘C were polycrystalline with the presence of an impurity BaCO₃ phase. The capacitance and leakage current were measured and used to extract information on the metal-BST interface. With the series capacitance model and modified Schottky emission equation, the thickness of the dead layers for Au/BST and Pt/BST interfaces were calculated to be less than 6 nm and 5 nm, respectively.     

ZnGa2O4 thin films fabricated by Sol-gel spinning coating process

ZnGa₂O₄ thin film phosphors have been synthesized on ITO coated glass and soda-lime glass at a firing temperature of 500^∘C and an annealing temperature of 500^∘C and 600^∘C via a chemical solution method using Zinc acetate dihydrate, Gallium nitrate hydrate and 2-methoxiethanol as a solution. XRD patterns of the film phosphors synthesized showed the peaks of ZnGa₂O₄ crystalline phases. AFM surface morphologies of the ZnGa₂O₄ thin film phosphors revealed marked differences according to an annealing temperature of 500^∘C and 600^∘C under an annealing atmosphere (3% H₂/Ar). On the other hand, the sheet resistance of ZnGa₂O₄ thin film phosphors, which were measured by four-point probe instrument, was approximately 5.76 Ω /square and 7.86 Ω /square with annealing temperature, respectively. The ZnGa₂O₄ thin film phosphors exhibited blue emission spectra with peak wavelength of 434 nm and 436 nm by ultra-violet excitation around 230 nm.     

Ferroelectric properties of heterolayered lead zirconate titanate thin films

Heterolayered Pb(Zr_{1 − x} Ti _x )O₃ thin films consisting of alternating PbZr_0.7Ti_0.3O₃ and PbZr_0.3Ti_0.7O₃ layers were successfully deposited via a multistep sol-gel route assisted by spin-coating. These heterolayered PZT films, when annealed at a temperature in the range of 600–700^∘C show (001)/(100) preferred orientation, demonstrate desired ferroelectric and dielectric properties. The most interesting ferroelectric and dielectric properties were obtained from the six-layered PZT thin film annealed at 650^∘C, which exhibits a remanent polarization of 47.7 μC/cm² and a dielectric permittivity of 1002 at 100 Hz. Reversible polarization constituents a considerably high contribution towards the ferroelectric hysteresis of the heterolayered PZT films, as shown by studies obtained from C-V and AC measurement.     

Preparation of Pb(Mg1/3Nb2/3)O3-PbTiO3 thin films by MOCVD using ultrasonic nebulization

Thin films of Pb(Mg_1/3,Nb_2/3)O₃ (PMN) and Pb(Mg_1/3,Nb_2/3)O₃-PbTiO₃ (PMN-PT) were fabricated on Si and Pt/Ti/SiO₂/Si substrates by MOCVD using ultrasonic nebulization and their characteristics were investigated. PMN-PT films deposited at 350^∘C were annealed in a RTA (Rapid Thermal Annealing) system at 650^∘C for 30 sec to improve the micostructural properties. The crystallographic properties of PMN-PT films strongly depend on the content ratio of PbTiO₃. The content of pyrochlore phase in PMN-PT films decreased with the increase of Ti content and nearly single phase perovskite films were obtained at the composition of 80PMN-20PT. The PMN-PT films with perovskite phase showed a typical butterfly type C-V curve which verifies the ferroelectricity and had the relative dielectric constant of about 60.     

The Study of Ferroelectric La-Doped PbTiO3 Thin Films Prepared by RF Magnetron Sputtering

Ferroelectric La-modified lead titanate (PLT) thin film were grown on Pt/Ti/SiO2/Si by sputtering the Pb_0.93La_0.07TiO₃ targets containing an amounts of excess 8% PbO. The effects of sputtering and annealing conditions on the crystalline structures and the surface morphologies of the PLT thin films have been investigated. The remanent polarization (Pr) and the coercive field of the PLT film through rapid thermal annealing (RTA) was 10.2 μC/cm² and 45 kV/cm respectively. The maximum pyroelectric coefficient reached 19 nC/cm².K at 20°C.     

Low frequency and microwave performances of Ba0.6Sr0.4TiO3 films on atomic layer deposited TiO2/high resistivity Si substrates

We report on high tunablity of Ba_0.6Sr_0.4TiO₃ (BST) thin films realized through the use of atomic layer deposited TiO₂ films as a microwave buffer layer between BST and a high resistivity (HR) Si substrate. Coplanar waveguide (CPW) meander-line phase shifters using BST/TiO₂/HR-Si and BST/MgO structures exhibited a differential phase shift of 95^∘ and 24.4^∘, respectively, at 15 GHz under an electric field of 10 kV/cm. The figure of merit of the phase shifters at 15 GHz was 30.6^∘/dB for BST film grown on a TiO₂/HR-Si substrate and 12.2^∘/dB for BST film grown on a MgO single crystal substrate. These results constitute significant progress in integrating BST films with conventional silicon technology.     

Dielectric and mechanical properties of hot-pressed SiCN/Si3N4composites

A series of high temperature radar wave-absorbing materials, SiCN/Si₃N₄ceramics, were prepared by hot-pressing. The nanometer SiCN powder, used as an absorber in the SiCN/Si₃N₄ceramic, was synthesized through laser pyrolysis of ((CH₃)₃Si)₂NH) and NH₃. The dielectric and mechanical properties of the prepared ceramics were investigated. XRD and SAED were conducted to study the growth of crystals in the ceramics. The results showed that the transformation of Si₃N₄from α to β was inhibited. The growth of the rod-like β -Si₃N₄grains in SiCN/Si₃N₄ceramics was retarded during hot-pressing process due to the existence of the nanometer SiCN particles. The relative density and the strength of the composites both decreased with the increase of the SiCN content in the composites. The dielectric properties of the ceramics prepared at different temperatures were very different. For the samples sintered at 1600^∘C and 1700^∘C, both the real and imaginary parts of the complex permittivity of them increased as the content of SCN powder in the sample obviously. For the sample with same concentration of SCN, the real and imaginary parts of them varied with the sintering temperature. SAED pattern revealed that structure of the SiCN in SiCN/Si₃N₄sintered at 1800^∘C tended to crystallize fully. Its real, imaginary parts and dissipation factor were much lower than those sintered at 1600^∘C and 1700^∘C greatly. Supported by national natural science foundation of China (No. 50572090)     

Fabrication of Er3+/Pr3+ Co-doped soda-lime glass thin films using RF magnetron sputtering method and optical property characterization

Er^3+/Pr³⁺ co-doped soda-lime glass thin films have been fabricated using RF magnetron sputtering method and their structural and optical properties have been studied. Deposition rate, crystallinity, and composition of glass thin films were investigated by scanning electron microscopy, transmission electron microscopy, and electron probe micro area analysis. Refractive index, birefringence and binding characteristics have been investigated using a prism coupler and X-ray photoelectron spectroscopy. Er³⁺/Pr³⁺ co-doped soda lime glass thin films were prepared by changing substrate temperature (room temp. ∼550^∘C), RF power (90 W–130 W), and Ar/O₂ gas flow ratio at processing pressure of 4 mTorr. Glass thin films could be obtained at the optimized processing condition at 350^∘C, RF power of 130 W, and gas flow of Ar:O₂ = 40:0 with maximum deposition rate of 1.6 μm/h. Refractive index and birefringence increased from 1.5614 to 1.5838 and from 0.000154 to 0.000552, respectively, as the content of Pr³⁺ increased. Binding energy of Pr3d also increased as the content of Pr³⁺ increased.     

Electrical properties of Ga2O3-based dielectric thin films prepared by plasma enhanced atomic layer deposition (PEALD)

Ga₂O₃ and Ga₂O₃-TiO₂ (GTO) nano-mixed thin films were prepared by plasma enhanced atomic layer deposition with an alternating supply of reactant sources, [(CH₃)₂GaNH₂]₃, Ti(N(CH₃)₂)₄ and oxygen plasma. The uniform and smooth Ga₂O₃ and GTO thin films were successfully deposited. Excellent step coverage of these films was obtained by chemisorbed chemical reactions with oxygen plasma on the surface. The dielectric constant of GTO thin film definitely increased compared to Ga₂O₃ film, and the leakage currents of GTO films were comparable to Ga₂O₃ films. The leakage current density of a 40-nm-GTO film annealed at 600^∘C was approximately 1×10⁻⁷ A/cm² up to about 600 kV/cm.     

Crystallinity and photocatalytic activity of liquid phase deposited TiO2 films

Anatase TiO₂ films were deposited on glass substrates at 50 and 200^∘C to investigate the effect of growth temperature on the photocatalytic acitivity of the films. It was observed that the films grown at 200^∘C were composed of columnar crystallites and were more porous than the films grown at 50^∘C which had more compact structures. Also, the film crystallinity increased from 75 to 90% if the higher growth temperature was used. Despite the higher crystallinity, it was observed that for crystallinities between 60 and 90%, the photocatalytic behavior of the films was more significantly affected by changes in the surface area.     

Study of nanocrystal TiO2 thin films by thermal annealing

The amorphous films were annealed in a wide temperature range (250–1000^∘C) and film properties of TiO₂ thin films were studied. Nano-sized anatase polycrystallites had been induced by thermal annealing for the films annealed at and above 300^∘C as confirmed by X-ray diffraction. Strong LO-phonon Raman modes, especially B_1g (395 cm⁻¹) and E _g (636 cm⁻¹) in Raman spectra and the absorption peak at 436 cm⁻¹ in absorbance spectra by Fourier transform infrared spectroscopy also indicated the existence of anatase phase in crystalline thin films. In addition, with the increase of the annealing temperature, the wettability of the film surface was enhanced as shown by the decrease of water contact angle from over 90^∘ to less than 40^∘. Moreover, upon UV laser irradiation on film surface, the water contact angle saturated at 10^∘ indicative of a highly hydrophilic surface for all the films, which arose from the dissociative adsorption of water molecules on the defect sits of the surface generated by the photocatalysis reactions of TiO₂. This behavior makes the film a good potential candidate for self-clean coatings.     

Ca Substituted PbTiO3 Thin Films for Infrared Detectors

Crack free Ca substituted PT thin films have been deposited on ITO coated 7059 glass substrates by sol gel technique and crystallized at 650C. Characterization of these films by X-ray diffraction show that the films exhibit tetragonal structure with perovskite phase. AFM, hysteresis, dielectric relaxation and pyroelectric studies have been carried out. The pyroelectric figures of merit of the films have been calculated. Our investigations show that these films are expected to give high infrared detector performance due to its high pyroelectric coefficient (43 nC/cm²K), high voltage responsivity (2340 Vcm²/J) and detectivity(3 × 10^{– 5} Pa^{– 1/2}) along with small value of dielectric constant (83) and loss tangent (0.04).     

Phase Formations and Electrical Properties of Various (Bi, La)4Ti3O12 Thin Films by Chemical Solution Deposition

The phase formation and electrical properties of (Bi, La)₄Ti₃O₁₂ (BLT) thin film and V-, Sm-doped BLT thin films prepared by the chemical solution deposition method on Pt/TiO₂/SiO₂/Si substrates have been investigated. It was observed that the microstructure and electrical properties of BLT thin films dramatically varied with V- and Sm-doping. The crystallinity and grain size of BLT thin films were definitely increased by V- and Sm-doping into BLT films, which resulted in the enhancement of remanent polarization in doped BLT films. The remanent polarization (Pr) of Sm-doped BLT films annealed for 3 min by an RTA system was about 9 C/cm². The V- and Sm-doped BLT films also exhibited good fatigue characteristics under bipolar stressing to 10¹⁰ cycles.     

Fabrication,property and application of novel pyroelectric single crystals—PMN–PT

The pyroelectric properties and temperature stability of Pb(Mg_1/3Nb_2/3)O₃–xPbTiO₃(PMN–xPT) single crystals (0.13 ≤ × ≤ 0.40) were investigated. The best choice for pyroelectric performance is [111]-oriented PMN–0.26PT single crystal whose figures of merit for voltage responsivity and detectivity are 0.11 m²/C and 15 × 10⁻⁵ Pa^−1/2, respectively. However, the [001]-oriented PMN–0.37PT single crystal has much better temperature stability, whose temperature coefficient of pyroelectric property is 0.5%/K in the range of 20 °C to 55 °C, and Curie temperature is high: 175 °C. We also found that PMN–xPT possessed low thermal diffusivity D ~ 4.4 × 10⁻⁷ m²/s, low volume specific heat C _v~ 2.5 × 10⁶ J/m³ K and tunable permittivity ε ~ (300–7000). The pyroelectric performances of PMN–xPT single crystals are superior to those of conventional pyroelectric materials and promising for IR device applications.