MIM capacitors using atomic-layer-deposited high-/spl kappa/ (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ dielectrics

Metal-insulator-metal (MIM) capacitors with (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ high-/spl kappa/ dielectric films were investigated for the first time. The results show that both the capacitance density and voltage/temperature coefficients of capacitance (VCC/TCC) values decrease with increasing Al/sub 2/O/sub 3/ mole fraction. It was demonstrated that the (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ MIM capacitor with an Al/sub 2/O/sub 3/ mole fraction of 0.14 is optimized. It provides a high capacitance density (3.5 fF//spl mu/m/sup 2/) and low VCC values (/spl sim/140 ppm/V/sup 2/) at the same time. In addition, small frequency dependence, low loss tangent, and low leakage current are obtained. Also, no electrical degradation was observed for (HfO/sub 2/)/sub 1-x/(Al/sub 2/O/sub 3/)/sub x/ MIM capacitors after N/sub 2/ annealing at 400/spl deg/C. These results show that the (HfO/sub 2/)/sub 0.86/(Al/sub 2/O/sub 3/)/sub 0.14/ MIM capacitor is very suitable for capacitor applications within the thermal budget of the back end of line process.     

High-density MIM capacitors using AlTaO/sub x/ dielectrics

The authors have obtained good MIM capacitor integrity of high-capacitance density of 10 fF//spl mu/m/sup 2/ using high-/spl kappa/ AlTaO/sub x/ fabricated at 400/spl deg/C. In addition, small voltage dependence of capacitance of <600 ppm (quadratic voltage coefficient of only 130 ppm/V/sup 2/) is obtained at 1 GHz using their mathematical derivation from measured high-frequency S parameters. These good results ensure the high-/spl kappa/ AlTaO/sub x/ MIM capacitor technology is useful for high-precision circuits operated at the RF frequency regime.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

A high-density MIM capacitor (13 fF//spl mu/m/sup 2/) using ALD HfO/sub 2/ dielectrics

Metal-insulator-metal (MIM) capacitors with different HfO/sub 2/ thickness have been investigated. The results show that both the capacitance density and voltage coefficients of capacitance (VCCs) increase with decreasing HfO/sub 2/ thickness. In addition, it is found that the VCCs decrease logarithmically with increasing thickness. Furthermore, the MIM capacitor with 10-nm HfO/sub 2/ shows a record high capacitance density of 13 fF//spl mu/m/sup 2/ and a VCC of 607 ppm/V, which can meet the requirement of the International Technology Roadmap for Semiconductors. It can also provide a low leakage current of 5.95 /spl times/ 10/sup -8/A/cm/sup 2/ at room temperature at 1 V, low tangent values below 0.05, and a small frequency dependence. These results indicate that the devices are suitable for use in silicon integrated circuit applications.     

Evidence and understanding of ALD HfO/sub 2/-Al/sub 2/O/sub 3/ laminate MIM capacitors outperforming sandwich counterparts

Metal-insulator-metal capacitors with atomic-layer-deposited HfO/sub 2/-Al/sub 2/O/sub 3/ laminated and sandwiched dielectrics have been compared, for the first time, for analog circuit applications. The experimental results indicate that significant improvements can be obtained using the laminated dielectrics, including an extremely low leakage current of 1/spl times/10/sup -9/ A/cm/sup 2/ at 3.3V and 125/spl deg/C, a high breakdown electric field of /spl sim/3.3MV/cm at 125/spl deg/C, good polarity-independent electrical characteristics, while retaining relatively high capacitance density of 3.13 fF//spl mu/m/sup 2/ as well as voltage coefficients of capacitance as low as -80 ppm/V and 100 ppm/V/sup 2/ at 100 kHz. The underlying mechanism is likely due to alternate insertions of Al/sub 2/O/sub 3/ layers that reduce the thickness of each HfO/sub 2/ layer, hereby efficiently inhibiting HfO/sub 2/ crystallization, and blocking extensions of grain boundary channels from top to bottom as well as to achieve good interfacial quality.     

RF, DC, and reliability characteristics of ALD HfO/sub 2/-Al/sub 2/O/sub 3/ laminate MIM capacitors for Si RF IC applications

High-performance metal-insulator-metal capacitors using atomic layer-deposited HfO/sub 2/-Al/sub 2/O/sub 3/ laminate are fabricated and characterized for RF and mixed-signal applications. The laminate capacitor can offer high capacitance density (12.8 fF//spl mu/m/sup 2/) up to 20 GHz, low leakage current of 4.9/spl times/10/sup -8/ A/cm/sup 2/ at 2 V and 125/spl deg/C, and small linear voltage coefficient of capacitance of 211 ppm/V at 1 MHz, which can easily satisfy RF capacitor requirements for year 2007 according to the International Technology Roadmap for Semiconductors. In addition, effects of constant voltage stress and temperature on leakage current and voltage linearity are comprehensively investigated, and dependences of quadratic voltage coefficient of capacitance (/spl alpha/) on frequency and thickness are also demonstrated. Meanwhile, the underlying mechanisms are also discussed.     

Very high density RF MIM capacitors (17 fF//spl mu/m/sup 2/) using high-/spl kappa/ Al/sub 2/O/sub 3/ doped Ta/sub 2/O/sub 5/ dielectrics

Using high-/spl kappa/ Al/sub 2/O/sub 3/ doped Ta/sub 2/O/sub 5/ dielectric, we have obtained record high MIM capacitance density of 17 fF//spl mu/m/sup 2/ at 100 kHz, small 5% capacitance reduction to RF frequency range, and low leakage current density of 8.9/spl times/10/sup -7/ A/cm/sup 2/. In combination of both high capacitor density and low leakage current density, a very low leakage current of 5.2/spl times/10/sup -12/ A is calculated for a typical large 10 pF capacitor used in RF IC that is even smaller than that of a deep sub-/spl mu/m MOSFET. This very high capacitance density with good MIM capacitor characteristics can significantly reduce the chip size of RF ICs.     

High-density MIM capacitors (/spl sim/85 nF/cm/sup 2/) on organic substrates

For the first time, transferring the prefabricated capacitors on a silicon wafer onto FR-4 has been used to realize high-density metal-insulator-metal (MIM) capacitors on an organic substrate. A high capacitance density /spl sim/85 nF/cm/sup 2/ was achieved on FR-4 substrate with PECVD silicon nitride as the dielectric layer. Excellent voltage coefficient (/spl sim/2.2 ppm/V/sup 2/) and temperature coefficient (/spl sim/38 ppm//spl deg/C) were obtained for capacitors on FR-4. Dielectric leakage and breakdown characteristics have been assessed, and the results demonstrated acceptable performance. Thus, this technology provides a new method to embed/integrate high-density capacitors on organic substrates for the system-in-package applications.     

Lanthanide (Tb)-doped HfO/sub 2/ for high-density MIM capacitors

A high-density metal-insulator-metal (MIM) capacitor with a lanthanide-doped HfO/sub 2/ dielectric prepared by physical vapor deposition (PVD) is presented for the first time. A significant improvement was shown in both the voltage coefficient of capacitance (VCC) and the leakage current density of MIM capacitor, yet the high capacitance density of HfO/sub 2/ dielectrics was maintained by achieving the doping of Tb with an optimum concentration in HfO/sub 2/. This technique allows utilizing thinner dielectric film in MIM capacitors and achieving a capacitance density as high as 13.3 fF//spl mu/m/sup 2/ with leakage current and VCC values that fully meet requirements from year 2005 for radio frequency (RF) bypass capacitors applications.     

High-performance poly-silicon TFTs using HfO/sub 2/ gate dielectric

High-performance low-temperature poly-Si thin-film transistors (TFTs) using high-/spl kappa/ (HfO/sub 2/) gate dielectric is demonstrated for the first time. Because of the high gate capacitance density and thin equivalent-oxide thickness contributed by the high-/spl kappa/ gate dielectric, excellent device performance can be achieved including high driving current, low subthreshold swing, low threshold voltage, and high ON/OFF current ratio. It should be noted that the ON-state current of high-/spl kappa/ gate-dielectric TFTs is almost five times higher than that of SiO/sub 2/ gate-dielectric TFTs. Moreover, superior threshold-voltage (V/sub th/) rolloff property is also demonstrated. All of these results suggest that high-/spl kappa/ gate dielectric is a good choice for high-performance TFTs.     

Very high-density (23 fF//spl mu/m/sup 2/) RF MIM capacitors using high-/spl kappa/ TaTiO as the dielectric

A very high density of 23 fF//spl mu/m/sup 2/ has been measured in RF metal-insulator-metal (MIM) capacitors which use high-/spl kappa/ TaTiO as the dielectric. In addition, the devices show a small reduction of 1.8% in the capacitance, from 100 kHz to 10 GHz. Together with these characteristics the MIM capacitors show low leakage currents and a small voltage-dependence of capacitance at 1 GHz. These TaTiO MIM capacitors should be useful for precision RF circuits.     

DRAM plate electrode bias optimization for reducing leakage current in UV-O/sub 3/ and O/sub 2/ annealed CVD deposited Ta/sub 2/O/sub 5/ dielectric films

A new plate biasing scheme is described which allowed the use of 65% higher supply voltage without increasing the leakage current for the UV-O/sub 3/ and O/sub 2/ annealed chemical-vapor-deposited tantalum pentaoxide dielectric film capacitors in stacked DRAM cells. Dielectric leakage was reduced by biasing the capacitor plate electrode to a voltage lower than the conventionally used value of V/sub cc//2. Ta/sub 2/O/sub 5/ films with 3.9 nm effective gate oxide, 8.5 fF//spl mu/m/sup 2/ capacitance and <0.3 /spl mu/A/cm/sup 2/ leakage at 100/spl deg/C and 3.3 V supply are demonstrated.<>     

Metal-insulator-metal RF bypass capacitor using niobium oxide (Nb/sub 2/O/sub 5/) with HfO/sub 2//Al/sub 2/O/sub 3/ barriers

A high capacitance density (C/sub density/) metal-insulator-metal (MIM) capacitor with niobium pentoxide (Nb/sub 2/O/sub 5/) whose k value is higher than 40, is developed for integrated RF bypass or decoupling capacitor application. Nb/sub 2/O/sub 5/ MIM with HfO/sub 2//Al/sub 2/O/sub 3/ barriers delivers a high C/sub density/ of >17 fF//spl mu/m/sup 2/ with excellent RF properties, while maintaining comparable leakage current and reliability properties with other high-k dielectrics. The capacitance from the dielectric is shown to be stable up to 20 GHz, and resonant frequency of 4.2 GHz and Q of 50 (at 1 GHz) is demonstrated when the capacitor is integrated using Cu-BEOL process.     

Integrated high-/spl kappa/ (/spl kappa/ /spl sim/19) MIM capacitor with Cu/low-/spl kappa/ interconnects for RF application

We demonstrate a high-performance metal-high /spl kappa/ insulator-metal (MIM) capacitor integrated with a Cu/low-/spl kappa/ backend interconnection. The high-/spl kappa/ used was laminated HfO/sub 2/-Al/sub 2/O/sub 3/ with effective /spl kappa/ /spl sim/19 and the low-/spl kappa/ dielectric used was Black Diamond with /spl kappa/ /spl sim/2.9. The MIM capacitor (/spl sim/13.4 fF//spl mu/m/sup 2/) achieved a Q-factor /spl sim/53 at 2.5 GHz and 11.7 pF. The resonant frequency f/sub r/ was 21% higher in comparison to an equivalently integrated Si/sub 3/N/sub 4/-MIM capacitor (/spl sim/0.93 fF//spl mu/m/sup 2/) having similar capacitance 11.2 pF. The impacts of high-/spl kappa/ insulator and low-/spl kappa/ interconnect dielectric on the mechanism for resonant frequency improvement are distinguished using equivalent circuit analysis. This letter suggests that integrated high-/spl kappa/ MIM could be a promising alternative capacitor structure for future high-performance RF applications.     

Si interlayer passivation on germanium MOS capacitors with high-/spl kappa/ dielectric and metal gate

We have demonstrated the advantages of silicon interlayer passivation on germanium MOS devices, with CVD HfO/sub 2/ as the high-/spl kappa/ dielectric and PVD TaN as the gate electrode. A silicon interlayer between a germanium substrate and a high-/spl kappa/ dielectric, deposited using SiH/sub 4/ gas at 580/spl deg/C, significantly improved the electrical characteristics of germanium devices in terms of low D/sub it/ (7/spl times/10/sup 10//cm/sup 2/-eV), less C- V hysteresis and frequency dispersion. Low leakage current density of 5/spl times/10/sup -7/ A/cm/sup 2/ at 1 V bias with EOT of 12.4 /spl Aring/ was achieved. Post-metallization annealing caused continuing V/sub fb/ positive shift and J/sub g/ increase with increased annealing temperature, which was possibly attributed to Ge diffusion into the dielectric during annealing.     

The effect of IrO/sub 2/--IrO/sub 2/--Hf--LaAlO/sub 3/ gate dielectric on the bias-temperature instability of 3-D GOI CMOSFETs

We have studied the bias-temperature instability of three-dimensional self-aligned metal-gate/high-/spl kappa//Germanium-on-insulator (GOI) CMOSFETs, which were integrated on underlying 0.18 /spl mu/m CMOSFETs. The devices used IrO/sub 2/--IrO/sub 2/-Hf dual gates and a high-/spl kappa/ LaAlO/sub 3/ gate dielectric, and gave an equivalent-oxide thickness (EOT) of 1.4 nm. The metal-gate/high-/spl kappa//GOI p-and n-MOSFETs displayed threshold voltage (V/sub t/) shifts of 30 and 21 mV after 10 MV/cm, 85/spl deg/C stress for 1 h, comparable with values for the control two-dimensional (2-D) metal-gate/high-/spl kappa/-Si CMOSFETs. An extrapolated maximum voltage of -1.2 and 1.4 V for a ten-year lifetime was obtained from the bias-temperature stress measurements on the GOI CMOSFETs.     

A novel program-erasable high-/spl kappa/ AlN-Si MIS capacitor

We demonstrate a programmable-erasable MIS capacitor with a single layer high-/spl kappa/ AlN dielectric on Si having a high capacitance density of /spl sim/5 fF//spl mu/m/sup 2/. It has low program and erase voltages of +4 and -4 V, respectively. Such an erase function is not available in other single layer Al/sub 2/O/sub 3/, AlON, or other known high-/spl kappa/ dielectric capacitors, where the threshold voltage (V/sub th/) shifts continuously with voltage. This device exhibits good data retention with a V/sub th/ change of only 0.06 V after 10 000 s.     

Electrical characteristics and reliability of UV transparent Si/sub 3/N/sub 4/ metal-insulator-metal (MIM) capacitors

In this paper, we discuss the electrical characteristics and reliability of UV transparent Si/sub 3/N/sub 4/ metal-insulator-metal (MIM) capacitors. We examine film thicknesses in the range of 55 to 25 nm with capacitance densities from 1.2 ff//spl mu/m/sup 2/ to 2.8 ff//spl mu/m/sup 2/, respectively, for single MIM capacitors. A new approach for projecting the dielectric reliability of these films extends the limits of maximum operating voltage. Accounting for temperature acceleration and area scaling, the projected lifetimes can be met for a wide range of operating conditions.     

Characteristics of HfO/sub 2/ pMOSFET prepared by B/sub 2/H/sub 6/ plasma doping and KrF excimer laser annealing

The electrical characteristics of HfO/sub 2/ pMOSFETs prepared by B/sub 2/H/sub 6/ plasma doping and excimer laser annealing were investigated. Various metal gate electrodes were evaluated to protect the high-/spl kappa/ oxide during laser irradiation. Although the aluminum gate electrode showed superior reflectivity to the laser, the equivalent oxide thickness was increased due to the interaction between aluminum and HfO/sub 2/, which resulted in reduced capacitance. In contrast, the Al-TaN stacked gate showed good reflectivity up to laser energy of 500 mJ/cm/sup 2/ and improved capacitance was obtained compared with the Al gate. For the first time, the electrical characteristics of a HfO/sub 2/ pMOSFET with an Al-TaN gate fabricated by plasma doping and excimer laser annealing were demonstrated. It was also demonstrated that plasma doping and excimer laser annealing combined with a metal gate could be applied for high-/spl kappa/ oxide MOSFET fabrication.     

Characterization of accumulation layer capacitance for extracting data on high-/spl kappa/ gate dielectrics

A new parameter extraction technique has been outlined for high-/spl kappa/ gate dielectrics that directly yields values of the dielectric capacitance C/sub di/, the accumulation layer surface potential quotient, /spl beta//sub acc/, the flat-band voltage, the surface potential /spl phi//sub s/, the dielectric voltage, the channel doping density and the interface charge density at flat-band. The parallel capacitance, C/sub p/(=C/sub sc/+C/sub it/), was found to be an exponential function of /spl phi//sub s/ in the strong accumulation regime, for seven different high-/spl kappa/ gate dielectrics. The slope of the experimental lnC/sub p/(/spl phi//sub s/) plot, i.e., |/spl beta//sub acc/|, was found to depend strongly on the physical properties of the high-/spl kappa/ dielectric, i.e., was inversely proportional to [(/spl phi//sub b/m/sup *//m)/sup 1/2/K/C/sub di/], where /spl phi//sub b/ is the band offset, and m/sup */ is the effective tunneling mass. Extraction of /spl beta//sub acc/ represented an experimental carrier confinement index for the accumulation layer and an experimental gate-dielectric direct-tunneling current index. /spl beta//sub acc/ may also be an effective tool for monitoring the effects of post-deposition annealing/processing.