Effect of anisotropy on fatigue properties of 2198 Al–Li plates joined by friction stir welding

Al–Li alloys are characterized by a strong anisotropy in mechanical and microstructural properties with respect to the rolling direction. In the present paper, 4 mm sheets of 2198 Al–Li alloy were joined via friction stir welding (FSW) by employing a rotating speed of 1000 mm/min and a welding speed of 80 mm/min in parallel and orthogonal direction with respect to the rolling one. The joints mechanical properties were evaluated by means of tensile tests at room temperature. In addition, fatigue tests were performed by using a resonant electro-mechanical testing machine under constant amplitude control up to 250 Hz sinusoidal loading. The fatigue tests were conducted in axial control mode with R = σ_min/σ_max = 0.33, for all the welding and rotating speeds used in the present study.     

Effect of welding parameters on mechanical and microstructural properties of dissimilar AA6082–AA2024 joints produced by friction stir welding

The effect of processing parameters on the mechanical and microstructural properties of dissimilar AA6082–AA2024 joints produced by friction stir welding was analysed in this study. Different samples were produced by varying the advancing speeds of the tool as 80 and 115 mm/min and by varying the alloy positioned on the advancing side of the tool. In all the experiments the rotating speed is fixed at 1600 RPM. All the welds were produced perpendicularly to the rolling direction for both the alloys. Microhardness (HV) and tensile tests performed at room temperature were used to evaluate the mechanical properties of the joints. The mechanical tests were performed on the joints previously subjected to annealing at 250 °C for 1 h. For the fatigue tests, a resonant electromechanical testing machine was employed under constant loading control up to 250 Hz sine wave loading. The fatigue tests were conducted in the axial total stress–amplitude control mode, with R = σ_min/σ_max = 0.1. In order to analyse the microstructural evolution of the material, the welds’ cross-sections were observed optically and SEM observations were made of the fracture surfaces.     

Reprint of “Multiaxial fatigue property of Ti–6Al–4V using hollow cylinder specimen under push-pull and cyclic inner pressure loading”

This paper studies a multiaxial fatigue crack mode and a fatigue life of Ti–6Al–4V. Load controlled fatigue tests at room temperature were carried out using a hollow cylinder specimen under multiaxial loading with principal stress ratio λ equal to 0, 0.4, 0.5 and 1.0 and loading ratio R kept constant and equal to 0. λ is defined as λ = σ₂/σ₁, where σ₁ and σ₂ are maximum and intermediate/minimum principal stresses, respectively. Here, the test at λ = 0 is a uniaxial loading test and that at λ = 1.0 an equi-biaxial loading test. A testing machine employed was a newly developed multiaxial fatigue testing machine which can apply push-pull and reversed torsion loading with inner pressure into the hollow cylinder specimen. Based on the obtained results in this study, multiaxial fatigue properties are examined, where the fatigue life evaluation and the crack mode are discussed. The fatigue life is reduced with an increase of λ, due to cyclic ratcheting and crack mode in multiaxial loading. The crack mode is also affected by the surface condition resulting from cut-machining.     

Multiaxial fatigue property of Ti–6Al–4V using hollow cylinder specimen under push-pull and cyclic inner pressure loading

This paper studies a multiaxial fatigue crack mode and a fatigue life of Ti–6Al–4V. Load controlled fatigue tests at room temperature were carried out using a hollow cylinder specimen under multiaxial loading with principal stress ratio λ equal to 0, 0.4, 0.5 and 1.0 and loading ratio R kept constant and equal to 0. λ is defined as λ = σ₂/σ₁, where σ₁ and σ₂ are maximum and intermediate/minimum principal stresses, respectively. Here, the test at λ = 0 is a uniaxial loading test and that at λ = 1.0 an equi-biaxial loading test. A testing machine employed was a newly developed multiaxial fatigue testing machine which can apply push-pull and reversed torsion loading with inner pressure into the hollow cylinder specimen. Based on the obtained results in this study, multiaxial fatigue properties are examined, where the fatigue life evaluation and the crack mode are discussed. The fatigue life is reduced with an increase of λ, due to cyclic ratcheting and crack mode in multiaxial loading. The crack mode is also affected by the surface condition resulting from cut-machining.     

Fatigue life assessment of friction spot welded 7050-T76 aluminium alloy using Weibull distribution

Friction spot welding is a solid state welding process suitable to obtain spot like-joints in overlap configuration. The process is particularly useful to weld lightweight materials in similar and dissimilar combinations, and therefore an interesting alternative to other joining techniques (rivets, resistance welding, etc.). Optimum process parameters have been defined using the Taguchi method by maximizing the response variable (the lap shear strength). A study of the fatigue life was carried out on specimens welded with the above mentioned optimized process parameters. Fatigue tests were performed using a stress ratio of R = 0.10. Two-parameter Weibull distribution was used to analyze statistically the fatigue life for the joined overlapped sheets. Subsequently, the Weibull plots were drawn, as well as S–N curves considering different reliability levels. The results show that for a relatively low load, corresponding to 10% of the maximum supported by the joint, the number of cycles surpasses 1 × 10⁶, hence infinite life of the service component can be attributed. Fatigue fracture surfaces were investigated for the highest and lowest loads tested using scanning electron microscope (SEM).     

Thermoelasticity and CCD analysis of crack propagation in AA6082 friction stir welded joints

The advantages of friction stir welding (FSW) process compared to conventional fusion welding technologies have been clearly demonstrated in recent years. In the present study, AA6082 FSW joints were produced by employing different welding parameters. The principal aim of this work is to apply thermoelastic stress analysis (TSA) to study crack propagation characteristics of friction stir welded aluminum sheets, during cyclic fatigue tests. The crack propagation experiments were performed by employing single edge notched specimens; fatigue tests were performed under tension with load ratio R = 0.1. All the mechanical tests were conducted up to failure. The TSA measurement system allowed crack evolution to be observed in real-time during fatigue cycles and stress fields to be derived on the specimens from the measured temperature variation. The thermoelastic data were used to analyse principal stresses and principal strains on the specimens surface and the crack growth rate during tests. In addition, it was possible to evaluate all the joints defects effects, as a function of welding parameters, correlating effects on different crack growth rate and instabilities. The achieved results were compared with those obtained by classical CCD camera monitoring of crack front propagation during cyclic loading and all the results were validated by employing finite element analysis performed with ABAQUS software.     

Numerical simulation of fatigue crack propagation in friction stir welded joint made of Al 2024-T351 alloy

In this work, fatigue crack propagation in thin-walled aluminium alloy structure with two friction stir welded T joints has been simulated numerically. Crack propagation in stiffened part of the structure between two friction stir welded T joints is analysed by using the eXtended Finite Element Method (XFEM), including software ABAQUS, as well as MORFEO, for modelling and results display. Tensile fatigue loading is applied, with stress ratio R = 0, and maximum stress σ_max = 10 MPa. Material properties (Al 2024-T351, as used in aeronautical industry) in different welded joints zones are adopted from available literature data. Following results are obtained by numerical analysis: stress–strain and displacement state in the structure, position of the crack tip and value of stress intensity factor for every crack propagation step, as well as the structural life estimation, i.e. number of load cycles, N, also for each crack propagation step. Using these results the number of cycles at which the crack starts to propagate in an unstable manner is predicted.     

The optimisation of process parameters for friction stir spot-welded AA3003-H12 aluminium alloy using a Taguchi orthogonal array

The aim of the present work is to optimise the welding parameters for friction stir spot welded non-heat-treatable AA3003-H12 aluminium alloy sheets using a Taguchi orthogonal array. The welding parameters, such as the tool rotational speed, tool plunge depth and dwell time, were determined according to the Taguchi orthogonal table L9 using a randomised approach. The optimum welding parameters for the peak tensile shear load of the joints were predicted, and the individual importance of each parameter on the tensile shear load of the friction stir spot weld was evaluated by examining the signal-to-noise ratio and analysis of variance (ANOVA) results. The optimum levels of the plunge depth, dwell time and tool rotational speed were found to be 4.8 mm, 2 s and 1500 rpm, respectively. The ANOVA results indicated that the tool plunge depth has the higher statistical effect with 69.26% on the tensile shear load, followed by the dwell time and rotational speed. The tensile shear load of the friction stir spot welding (FSSW) joints increased with increasing plunge depth. Additionally, examination of the weld cross-sections, microhardness tests and fracture characterisation of the selected friction spot welded joints were conducted to understand the better performance of the joints. All the fractures of the joints during tensile testing occurred at stir zone (SZ), where the bonded section was minimum. The tensile shear load and tensile deformation of the FSSW joints increased linearly with increasing the bonded size. The finer grain size in the SZ led to the higher hardness, which resulted in higher fracture strength. When the tensile shear load of the joints increased approximately 3-fold, the failure energy absorption of the joints increased approximately 15-fold.     

Consideration of mean-stress effects on fatigue life of welded magnesium joints by the application of the Smith–Watson–Topper and reference radius concepts

Three types of welded joints have been assessed with regard to their fatigue strength based on the mean-stress damage parameter model according to Smith, Watson, and Topper (P_SWT) and on the reference notch radius concept. These analyses were performed with three different stress ratios, R = −1, R = 0 and R = 0.5, under axial loading. For each stress level, the corresponding Neuber-Hyperbolas, Masing-loops and their maximum stress and maximum strain values were determined in order to calculate damage parameter (P_SWT) values. For a given weld geometry, this damage parameter is able to unify the fatigue results for different R-values within at a tight scatter band and therefore to consider the mean-stress effect. The unification of the results for different weld geometries is performed by applying the reference radii r_ref = 0.05 and r_ref = 1.00 mm as suggested by the IIW-Recommendations.     

The investigation of crack growth in specimens with rectangular cross-sections under out-of-phase bending and torsional loading

The paper presents the fatigue test results of rectangular cross-section specimens made of 10HNAP (S355J2G1W) steel. The specimen height to width ratio was 1.5. The tests under bending with torsion were performed for the following ratios of bending to torsional moments M_aB/M_aT = 0.47, 0.94, 1.87 and the loading frequency 26.5 Hz. Nominal stresses were chosen for the equivalent stress according to the Huber-Mises hypothesis equal to 360 MPa. The tests were performed in the high cycle fatigue regime for the stress ratio R = −1 and phase shift between bending and torsion loading equal to ϕ = 0 and 90°. Crack initiation and propagation phases were observed on the specimen surface using the optical microscope (magnification 20×) with an integrated digital camera. The test results for the fatigue crack growth rate versus the stress intensity factor range for mode I and mode III have been described with the Paris equation.     

Fatigue of 2024-T351 aluminium alloy at different load ratios up to 1010 cycles

Fatigue properties of 2024-T351 aluminium alloy are investigated in the high cycle fatigue (HCF) and very high cycle fatigue (VHCF) regime. Endurance tests are performed with ultrasonic equipment at 20 kHz cycling frequency at load ratios of R = −1, R = 0.1 and R = 0.5 up to 10¹⁰ cycles. Additional servo-hydraulic tests between 8 and 10 Hz at R = 0.1 show no frequency influence on fatigue lifetimes. Linear lines in double logarithmic S–N plots are used to approximate data. Slope exponents of approximation lines increase with increasing numbers of cycles for all load ratios. Failures above 5 × 10⁹ cycles (R = −1 and R = 0.1) or 10¹⁰ cycles (R = 0.5) occur, and no fatigue limit is found. Fatigue cracks leading to failures above 10⁹ cycles are initiated at the surface or slightly below at broken constituent particles or at agglomerations of fractured particles, which are probably Al₇Cu₂(Fe, Mn). Specimens stressed with more than 10¹⁰ cycles at R = −1 without failure show several cracks starting at constituent particles. Maximum crack lengths are 30 μm, which is considerably below grain size.     

Feasibility study of friction spot welding of dissimilar single-lap joint between poly(methyl methacrylate) and poly(methyl methacrylate)-SiO2 nanocomposite

In this work, the feasibility of friction spot welding (FSpW) of a commercial poly(methyl methacrylate) (PMMA) GS grade and a PMMA 6 N/2 wt% silica (SiO₂) nanocomposite was investigated. Single-lap joints welded at rotational speeds of 1000, 2000 and 3000 rpm were produced. The analysis of the joint microstructure and material flow pattern indicated that joints could be produced using all of the tested welding conditions. However, the joint produced at 1000 rpm displayed sharp weld lines (weak links), indicating insufficient heat input, while the welds produced at 3000 rpm displayed excessive plastic deformation (bulging of the bottom plate), volumetric defects and a lack of material mixing in the welded area, associated with higher heat input. The weld produced at a rotational speed of 2000 rpm resulted in improved material mixing, which was indicated by the absence of weld lines and volumetric defects due to the more correct heat input. This welding condition was selected for further mechanical testing. Lap shear testing of PMMA GS/PMMA 6 N/2 wt% SiO₂ nanocomposite single lap joints welded at 2000 rpm resulted in an average ultimate lap shear strength of 3.9 ± 0.05 MPa. These weld strength values are equal to or better than those obtained using state-of-the-art welding techniques for PMMA materials, thereby demonstrating the potential of friction spot welding for thermoplastic nanocomposites.     

Carbon composites based on multi-axial multi-ply stitched preforms – Part 6. Fatigue behaviour at low loads: Stiffness degradation and damage development

This article studies the fatigue properties of a carbon-fibre cross-ply non-crimp fabric reinforced epoxy composite. Tensile–tensile fatigue cycling was carried out at load levels corresponding to the onset of damage in a static tensile test, in machine, cross and bias direction. Specimens in machine and cross direction did not fail up to 10⁶ cycles; specimens in bias direction had an average fatigue life N_max of 3 × 10⁵ cycles. Stiffness degradation in bias direction samples was found to be more severe than in machine or cross direction. Damage development in the samples was studied by means of X-ray photography and appears to show remarkable resemblance to the development under a static tensile test and can be qualitatively compared to the behaviour of non-stitched UD laminates. Post-fatigue tensile tests were done at various stages of the fatigue life. Small differences in damage onset strain level can be found. Failure strain of bias direction tested samples shows significant decrease upon cycling.     

Fatigue assessment of root failures in HSLA steel welded joints: A comparison among local approaches

Fatigue tests were performed on welded joints made of high-strength, low-alloy steel (S690). Different welding processes were tested, resulting in welds with different defects essentially consisting in lack of penetration. Fatigue tests were run with both constant and variable amplitude loading. The experimental results were compared to predictions obtained by applying local approaches (local stress and local strain) and the concepts of fracture mechanics. The local stress approach allowed the fatigue strength of joints in constant amplitude loading (for fatigue above 2 × 10⁶) to be predicted, but the assumption of a constant value of the slope k = 3 for all S–N curves led to non-conservative predictions of shorter lives. The local strain approach allowed the fatigue strength of the joints under constant amplitude to be predicted. Although, these predictions matched the experimental data well for both small and large defects in the entire cycle number range, they failed to predict the behaviour of joints under variable amplitude loading. Conversely, the fracture mechanics approach proved to be more efficient in predicting the fatigue behaviour of welded joint under variable amplitude loading.     

Influence of temperature and thickness on the off-axis behaviour of short glass fibre reinforced polyamide 6.6 – cyclic loading

This paper investigates the anisotropic properties of short glass fibre reinforced polyamide 6.6 (PA66-GF35) under tension–tension and tension–compression cyclic loading. Tensile fatigue tests were carried out on dog-bone specimens, machined out from injection-moulded plates 80 × 80 mm, of three different thicknesses t (1 and 3 mm) at three different nominal fibre orientation angles θ (0°, 30° and 90°). The tests were carried out at RT as well as at 130 °C.The Tsai–Hill failure criterion, modified to account for cyclic loading, is applied to the fatigue data for estimating the fatigue strength parameters of the material under investigation. Results are compared to the strength parameters obtained under quasi-static loading in a previous part of this work [De Monte M, Moosbrugger E, Quaresimin M. Influence of temperature and thickness on the off-axis behaviour of short glass fibre reinforced polyamide 6.6 – quasi-static loading. Composites: Part A, 2010;41(10):1368–79]. The experimental results highlight how specimen thickness remarkably affects mechanical properties: the thinner the specimen the higher will be the degree of anisotropy. Also temperature strongly reduces the fatigue strength under cyclic loading. The Tsai–Hill criterion allows for an adequate fitting of experimental data at the investigated temperatures and load ratios.     

3-Dimensional observation of the interior fracture mechanism and establishment of cumulative fatigue damage evaluation on spot welded joints using 590 MPa-class steel

To investigate the fatigue fracture mechanism in spot welded joints using a 590 MPa-class base metal, fatigue tests were conducted under constant loading conditions. In this study, three dimensional observation was made on the propagation behavior of fatigue cracks initiating at the edge of the slit between sheets. Moreover, an evaluation method of the fatigue life was proposed for random loading conditions. Since the mean load obviously affected the fatigue life of the spot welded joints, the proposed evaluation method was applied to account for this load effect. The proposed evaluation method satisfied the application range in the automobile industry. Therefore, it is thought that the proposed method is suitable for practical applications.     

J-integral-based approach to fatigue assessment of laser stake-welded T-joints

The aim of this paper is to investigate the influence of the plate thickness on the fatigue strength of laser stake-welded T-joints under the tension loading condition. Fatigue tests were conducted on specimens with plate thicknesses below 5 mm subjected to tension loading with the load ratio R = 0. The statistical analysis of the weld geometry showed a normal distribution of the each parameter that was measured. In addition, the parameters had similar proportions in comparison to the specimens with plate thicknesses above 5 mm. FE analysis was performed with the aim of determining the stress state in the joint along with the J-integral. If the square root of the J-integral, √ΔJ, is used as the fatigue strength assessment parameter, the fatigue strength obtained at five million cycles is similar as in the case of other steel welded joint types. The investigation concluded that the stress state changes with the reduction of the plate thicknesses and the contribution of fracture mode II becomes significant. However, using √ΔJ as a fatigue strength assessment parameter ensures that the complex state of the mixed fracture mode loading is accurately accounted for. This fact further enables the fatigue strength of laser stake-welded T-joints of any plate thicknesses to be described by means of a narrower scatterband than the one obtained by the nominal stress approach.     

Off-axis tensile fatigue assessment based on residual strength for the unidirectional 45° carbon fiber-reinforced composite at room temperature

The tensile fatigue behavior of unidirectional carbon fiber-reinforced thermoplastic and thermosetting laminates was examined at room temperature. Tension-tension cyclic fatigue tests were conducted under load control at a sinusoidal frequency of 10 Hz to obtain stress-fracture cycles (S-N) relationship. The fatigue limits of carbon fiber-reinforced thermoplastic laminates (CF/PA6) and thermosetting laminates (CF/Epoxy) were found to be 28.0 MPa (48% of the tensile strength) and 56.2 MPa (63% of the tensile strength), respectively. Two types (in constant and incremental loading way) of loading-unloading low cycle fatigue tests were employed to investigate the modulus history of fatigue process for announcing the fatigue mechanism. The residual tensile strength of specimens that survived fatigue loading maintained with the increase of fatigue cycles and applied stress. Examination of the fatigue-loaded specimens revealed that the more flexible/ductile trend of resins and the formation of micro-cracks at the interface between fiber and matrix was facilitated during high fatigue loading (⩾fatigue limit stress), while no interfacial/matrix damage in resins was detected during low fatigue loading (<fatigue limit stress), which was consider to be the governing mechanism of strength maintain during fatigue loading.     

Fatigue strength of sharp V-notched specimens made of ductile cast iron

In the present, the high cycle fatigue strength of notched ductile cast iron is investigated. Experimental tests under axial loading, has been carried out on sharp V-notched specimens taken from heavy section casting considering nominal load ratios (R = 0). All specimens, taken from a heavy section casting, are characterized by a notch tip radius less than 0.1 mm, a notch depth of 10 mm and a notch opening angle = 90°. In order to evaluate the influence of chunky graphite morphology on fatigue life, fatigue tests were carried out also on a second set of specimens without that microstructural defect.Metallurgical analyses were performed on all the samples and some important microstructural parameters (nodule count and nodularity rating, among others) were measured and compared. It was found that a mean content of 40% of chunky graphite in the microstructure (with respect to total graphite content) does not influence significantly the fatigue strength properties of the analysed cast iron.     

Fatigue behavior and failure mechanism of basalt FRP composites under long-term cyclic loads

This paper studies the fatigue behavior of basalt fiber reinforced epoxy polymer (BFRP) composites and reveals the degradation mechanism of BFRP under different stress levels of cyclic loadings. The BFRP composites were tested under tension–tension fatigue load with different stress levels by an advanced fatigue loading equipment combined with in-situ scanning electron microscopy (SEM). The specimens were under long-term cyclic loads up to 1 × 10⁷ cycles. The stiffness degradation, S–N curves and the residual strength of run-out specimens were recorded during the test. The fatigue strength was predicted with the testing results using reliability methods. Meanwhile, the damage propagation and fracture surface of all specimens were observed and tracked during fatigue loading by an in-situ SEM, based on which damage mechanism under different stress levels was studied. The results show the prediction of fatigue strength by fitting S–N data up to 2 × 10⁶ cycles is lower than that of the data by 1 × 10⁷ cycles. It reveals the fatigue strength perdition is highly associated with the long-term run-out cycles and traditional two million run-out cycles cannot accurately predict fatigue behavior. The SEM images reveal that under high level of stress, the critical fiber breaking failure is the dominant damage, while the matrix cracking and interfacial debonding are main damage patterns at the low and middle fatigue stress level for BFRP. Based on the above fatigue behavior and damage pattern, a three stage fracture mechanism model under fatigue loading is developed.