Microstructure and mechanical performance of metal-composite hybrid joints produced by FricRiveting

The mechanical performance and microstructure of friction riveted metallic-insert joints made of polyether ether ketone composite reinforced with 30% short carbon fibers and titanium grade 3 was studied. The metallic-insert joints reached a maximal pull-out tensile force of 10.6 kN, which corresponds to 100% of the titanium base material strength. It was shown the pull-out force increased as the rivet tip widened. Frictional heat during the process was mainly generated by the friction between the tip of the rivet and the composite substrate in the friction zone. Microstructural analyses of the metallic part of the joint revealed the presence of different microstructural zones: a friction zone, and two thermomechanically affected zones 1 and 2. Based on the composite morphology, the composite part of the joint was categorized into three different zones: the stir zone, a thermomechanically affected zone and a heat-affected zone. A study of the material flow showed that the flow of the composite was strongly affected by the rotation and axial movement of the rivet.     

Spot friction stir welding of low carbon steel plates preheated by high frequency induction

In this study, high frequency induction heating assisted spot friction stir welding was applied to 1.6 mm thick S12C low carbon steel plates. With the same welding parameter including an applied load of 2500 kg, rotation speed of 800 rpm and dwell time of 2 s, the average grain size in the stir zone slightly increased from 12.9 μm for the welds without preheating to 14.8 μm when 10 s preheating was used. However, larger joint interface was formed within the stir zone of the welds with preheating and therefore the bonding strength can be significantly increased. As a result, the shear tensile load of the joint increased from 8 kN to12.4 kN with preheating and the joint fractured through the plug failure mode rather than interfacial failure mode. It was revealed that the frictional heat generated between the rotating tool and the work-piece can be reduced to obtain sound welds by means of high frequency induction preheating.     

Tensile behavior of friction stir welded AA 6061-T4 aluminum alloy joints

In this investigation response surface methodology based on a central composite rotatable design with three parameters, five levels and 20 runs, was used to develop a mathematical model predicting the tensile properties of friction stir welded AA 6061-T4 aluminum alloy joints at 95% confidence level. The three welding parameters considered were tool rotational speed, welding speed and axial force. Analysis of variance was applied to validate the predicted model. Microstructural characterization and fractography of joints were examined using optical and scanning electron microscopes. Also, the effects of the welding parameters on tensile properties of friction stir welded joints were analyzed in detail. The results showed that the optimum parameters to get a maximum of tensile strength were 920 rev/min, 78 mm/min and 7.2 kN, where the maximum of tensile elongation was obtained at 1300 rev/min, 60 mm/min and 8 kN.     

Effect of the design parameters on the in vitro wear performance of total shoulder arthroplasties

The loosening of the glenoid component is the main reason for the failure of a total shoulder arthoplasty. It may be caused either by high tensile stresses or by osteolysis of the surrounding bone in response to the presence of particle debris. This failure might be associated with the wear of the implant as occurs with replacement hip and knee joints.The paper reports the findings of a study of the in vitro performance of the currently used total shoulder prostheses to determine the effects of implant geometry on the wear of the polyethylene components and the friction conditions operating within the shoulder prosthesis.The wear performance of the implants was evaluated using a self-developed tribotester, simulating the physiological conditions of a shoulder joint. This study revealed that significantly different wear occurred with conforming and non-conforming articulation and revealed the influence of the thickness of the polyethylene glenoid on the wear and friction occurring in the joint. In this preliminary study significant wear of the polyethylene glenoid component occurred, estimated to be up to 19 mm³/year, which is similar to that found in retrieved implants. The conforming implants demonstrated significantly greater wear than the non-conforming implants (p < 0.05). A significantly lower friction factor, about 0.05 ± 0.01 (p < 0.05), was obtained for the less conforming implants.     

Microstructure and mechanical optimization of probeless friction stir spot welded joint of an Al-Li alloy

In this work, a third generation Al-Li alloy has been successfully spot welded with probeless friction stir spot welding (P-FSSW), which is a variant of conventional friction stir welding. The Box-Behnken experimental design in response surface methodology (RSM) was applied to optimize the P-FSSW parameters to attain maximum tensile/shear strength of the spot joints. Results show that an optimal failure load of 7.83 kN was obtained under a dwell time of 7.2 s, rotation speed of 950 rpm and plunge rate of 30 mm/min. Sufficient dwell time is essential for heat conduction, material flow and expansion of the stir zone to form a sound joint. Two fracture modes were observed, which were significantly affected by hook defect. In addition to mechanical testing, electron backscattering diffraction (EBSD) and differential scanning calorimetry (DSC) were used for microstructure evolution and property analysis. The precipitation of GP zone and Al₃Li as well as the ultrafine grains were responsible for the high microhardness in the stir zone.     

Effect of welding parameters on microstructure and mechanical properties of friction stir spot welded 5052 aluminum alloy

Friction stir spot welding (FSSW) is a newly-developed solid state joining technology. In this study, two types of FSSW, normal FSSW and walking FSSW, are applied to join the 5052-H112 aluminum alloy sheets with 1 mm thickness and then the effect of the rotational speed and dwell time on microstructure and mechanical properties is discussed. The lower sheet material underneath the hook didn’t flow into the upper sheet due to the concave surface in the shoulder and groove in the anvil. The hardness profile of the welds exhibited a W-shaped appearance and the minimum hardness was measured in the HAZ. The results of tensile/shear tests and cross-tension tests indicate that the joint strength decreases with increasing rotational speed, while it’s not affected significantly by dwell time. At the rotational speed of 1541 rpm, the tensile/shear strength and cross-tension strength reached the maximum of 2847.7 N and 902.1 N corresponding to the dwell time of 5 s and 15 s. Two different fracture modes were observed under both tensile/shear and cross-tension loadings: shear fracture and tensile/shear mixed fracture under tensile/shear loadings, and nugget debonding and pull-out under cross-tension loadings. The performance of the welds plays a predominant role in determining the type of fracture modes. In addition, the adoption of walking FSSW brings unremarkable improvements in weld strength.     

The effect of tool rotational and traverse speed on friction stir weldability of AISI 430 ferritic stainless steels

In this study, the effects of tool rotational speed and traverse speed on welding of AISI 430 (X6Cr17, material number 1.4016) ferritic stainless steels by friction stir welding method are examined. Two specimens with dimension of 3 × 100 × 200 mm were joined in butt position. Tool rotational speeds were determined to be 560–1400 min⁻¹ and traverse speeds as 80–200 mm/min. During the studies, tool pressure force 3.5 kN and tool angle of 0° was kept constant. Hard metal carbide (WC-Co hard metal identified as K10) with equilateral triangle tip profile was used as the tool material. Determination of the tool advance speeds related to the tool rotation speeds giving the best-looking weld seals with acceptable values of mechanical properties was aimed.During welding of the specimens joined in butt position, the temperature change due to time and variation of the pressure force applied on welded specimens by the tool shoulder has been recorded. It has been observed that the best mechanical resistance values were obtained at tool rotational speed of 1120 min⁻¹ through five tool rotational speeds (560–1400). Also it has been observed that the best mechanical resistance values were obtained at traverse speed of 125 mm/min through five traverse speeds (80–200) with the constant tool pressure force of 3.5 kN and tool angle of 0°.     

Achieving superior mechanical properties in friction lap joints of copper to carbon-fiber-reinforced plastic by tool offsetting

It is a challenge to achieve a sound welded metal/carbon-fiber-reinforced thermoplastic (CFRTP) joint with high strength and few bubbles. In this study, sound lap joints of Cu and CFRTP were obtained by friction lap joining (FLJ) directly at rotation rates of 600–2000 rpm, with the welding tool at the joint center and offsetting the tool 7 mm away from the center toward the retreating side, respectively. Tool offsetting reduced the non-uniform temperature distribution in the lap joints resulting from the high conductivity of Cu, which not only enhanced the tensile shear force from 0.89–2.25 kN to 1.71–3.54 kN, with the maximum increasing rate of 135%, but also reduced the bubble area to only 19% of the original level of 2000 rpm. It is the first time to report a high-quality Cu/CFRTP joint with a high strength and few bubbles. The large increase of the strength after tool offsetting was attributed to the increase of the joining area, the decrease of bubbles and the decrease of the CFRTP degradation. The details on the generation, quantitative distribution and expulsion of the bubbles in the FLJ joints were discussed.     

Improving mechanical properties of pinless friction stir spot welded joints by eliminating hook defect

Hook defect (HD) seriously decreases the mechanical properties of friction stir spot welded (FSSW) joints. In this study, two methods were therefore used to eliminate the HD in pinless FSSW joints. The one is changing welding parameters such as rotating speed and dwell time. The other one is FSSW plus subsequent friction stir welding (FSSW-FSW), which is an innovative method proposed in this study. Experimental results showed that the HD in pinless FSSWed AA2024 joints was successfully eliminated by using FSSW-FSW, not by changing process parameters. The joints without HD exhibited a tensile–shear load of as much as 12 kN, which was higher than that of 6.9 kN in the joints with HD. Furthermore, it was proved that the tensile–shear load is not greatly improved only by increasing the nugget zone when HD still existed in the FSSW joints. In addition, the fracture morphology analysis demonstrated that the shear fracture of the FSSW-FSW joints took place along the boundary between the upper and lower sheets through the weld nugget, and the faying surface between the two sheets was completely sheared off.     

Effect of friction time on mechanical and metallurgical properties of continuous drive friction welded Ti6Al4V/SUS321 joints

Dissimilar joint of Ti6Al4V titanium alloy and SUS321 stainless steel was fabricated by continuous drive friction welding. The effect of friction time on the mechanical properties was evaluated by hardness measurement and tensile test, while the interfacial microstructure and fracture morphologies were analyzed by scanning electron microscope, energy dispersive spectroscope and X-ray Diffraction. The results show that the tensile strength increases with friction time under the experimental conditions. And the maximum average strength 560 MPa, which is 90.3% of the SUS321 base metal, is achieved at a friction time of 4 s. For all samples, studied fracture occurred along the joint interface, where intermetallic compounds like FeTi, Fe₂Ti, Ni₃(Al, Ti) and Fe₃Ti₃O and many other phases were formed among elements from the two base metals. The width of intermetallic compounds zone increases with friction time up to 3 μm, below which it is beneficial to make a strong metallurgical bond. However, the longer friction time leads to oversized flash on the Ti6Al4V side and overgrown intermetallic compounds. Finally the optimized friction time was discussed to be in the range of 2–4 s, under which the sound joint with good reproducibility can be expected.     

Effect of boron content and welding current on the mechanical properties of electrical resistance spot welds in complex-phase steels

When complex phase steel where tensile strength is more than 1 GPa grade is joined by resistance spot welding (RSW) optimum boron (B) content should be chosen to satisfy weldability and mechanical properties. Therefore, in this study, the effect of the B content (0–40 ppm) on the tensile-shear strength of the RSW were investigated. As the resistivity of the base metal was independent on the B content it did not affect to nugget diameter. Regardless of the B content the specimens under 5t^1/2 (t = sheet thickness) were fractured at interfacial failure mode. In the low welding current condition (lower than 6.4 kA), measured nugget diameters were smaller than calculated critical nugget diameter regardless of the amount of B addition so that fracture mode was interfacial failure. Pull out failure occurred at the softened zone which was boundary between the base metal and the heat affected zone. Tensile-shear load of the specimen failure at the pull-out mode was increased as the fractured diameter and hardness of the softened zone were increased. Shear load was only dependent on the fractured diameter. The equations to calculate the shear and tensile-shear load were suggested for the specimens fractured at interfacial and pull-out failure modes respectively. Correlation coefficients between measured and calculated values of shear and tensile-shear load were 0.98 and 0.97, respectively. Therefore, shear and tensile-shear load of advanced high strength steel joined by RSW could be predicted successfully using the suggested equation.     

Experimental investigation of the role of frictional yarn pull-out and windowing on the probabilistic impact response of kevlar fabrics

The probabilistic impact responses of single layer greige and scoured plain-weave Kevlar KM2 fabrics are experimentally studied. Single-layer, 101 cm × 101 cm fabric targets are mounted in a novel equilateral octagon (EO) fixture that leaves the principal yarns unclamped. A probabilistic velocity response (PVR) curve, which describes the probability of fabric penetration as a function of projectile impact velocity, is generated through a series of thirty impact tests using a spherical steel projectile impacted at velocities between 69 and 113 m/s. Additional experiments are conducted by impacting targets repeatedly at identical velocities, and comparing the resulting residual velocities of the penetrating projectiles. Fabric penetration in all cases is entirely accommodated by yarn pull-out and windowing, without any principal yarn failure at the impact site. The results indicate that frictional yarn sliding and pull-out are the primary energy dissipating mechanisms during these impact conditions. Controlled yarn pull-out experiments are conducted on the same greige and scoured fabrics to statistically characterize the yarn pull-out loads. Variability in pull-out forces in the greige fabrics are measurably higher than the variability in pull-out forces for the scoured fabrics, which correlates well with variability trends in the PVR and residual velocity ballistic experiments. Additional factors, such as yarn-projectile friction and differences in filament packing efficiency, are hypothesized to also contribute to the observed differences in the greige and scoured fabric impact responses.     

Interfacial microstructure and mechanical property of resistance spot welded joint of high strength steel and aluminium alloy with 4047 AlSi12 interlayer

Dissimilar materials of H220YD galvanised high strength steel and 6008-T66 aluminium alloy were welded by means of median frequency direct current resistance spot welding with employment of 4047 AlSi12 interlayer. Effects of interlayer thickness on microstructure and mechanical property of the welded joints were studied. The welded joint with interlayer employed could be recognised as a brazed joint. The nugget diameter had a decreased tendency with increasing thickness of interlayer under optimised welding parameters. An intermetallic compound layer composed of Fe₂(Al,Si)₅ and Fe₄(Al,Si)₁₃ was formed at the interfacial zone in the welded joint, the thickness and morphology of which varying with the increase of interlayer thickness. Reaction diffusion at the steel/aluminium interface was inhibited by introduction of silicon atoms, which restricted growth of Fe₂(Al,Si)₅. Tensile shear load of welded joints experienced an increased tendency with increasing interlayer thickness from 100 to 300 μm, and the maximum tensile shear load of 6.2 kN was obtained with interlayer thickness of 300 μm, the fractured welded joint of which exhibiting a nugget pullout failure mode.     

Formation and mechanical properties of stationary shoulder friction stir welded 6005A-T6 aluminum alloy

6005A-T6 aluminum alloy is welded by stationary shoulder friction stir welding (SSFSW). At a constant rotational velocity of 2000 rpm, the effect of welding speed on mechanical properties of SSFSW joint are investigated in detail. Defect-free joint with gloss surface and small flash is attained and no cracks appear at the bending angle of 180°. Compared with traditional friction stir welding (FSW), width of rotational shoulder affected zone is relatively small because of the smaller diameter of rotational shoulder. Increasing welding speed is benefit for reducing the width of softening region and the softening degree. The fracture position of welding joint locates in thermo-mechanically affected zone and the fracture surface morphology presents the typical ductile fracture. The maximum tensile strength of joint at the welding speed of 400 mm/min reaches 82% of base metal (BM).     

Joining phenomena and tensile strength of friction welded joint between pure titanium and low carbon steel

This paper describes the effect of the friction welding condition on the joining phenomena and the tensile strength of friction welded joint between pure titanium (P-Ti) and low carbon steel (LCS). The adjacent region of the weld interface at the P-Ti side was intensely upsetting with accompanied large deformation of itself when the joint had sparkle at both applied friction pressures of 30 and 90 MPa, although that of the LCS side was hardly upset. The temperature of the whole weld interface at a friction pressure of 30 MPa reached to 1150 K or over at a friction time of 3.0 s or longer. However, the half radius and centreline portion temperatures of the weld interface at a friction pressure of 90 MPa was not reached to 1150 K, although the periphery portion of that was reached to its temperature. The central portion of the weld interface at a friction pressure of 90 MPa was deformed to a convex shape from the viewpoint of the P-Ti side, although that of 30 MPa remained almost flat after when the friction torque reached the initial peak. When the joint was made at a friction pressure of 30 MPa, a friction time of 3.0 s or longer, and a forge pressure of 270 MPa or higher, it achieved 100% joint efficiency and the P-Ti base metal fracture with no crack at the weld interface. However, many joints at friction times of 1.2 and 1.5 s fractured at the weld interface, although those achieved 100% joint efficiency, because whole weld interface temperature was below 1150 K. On the other hand, many joints at a friction pressure of 90 MPa with high forge pressure also fractured at the weld interface, although those achieved 100% joint efficiency, because the weld interface temperature at the half radius and periphery portions was below 1150 K. Those joints did not have the intermetallic compound layer at the weld interface. The difference of the fractured portion of the joint in both applied friction pressures was due to the difference between the maximum temperature at the weld interface during the friction process and the deformation amount of the LCS side caused by applied forge pressure. To obtain 100% joint efficiency with the P-Ti base metal fracture with no crack at the weld interface, the joint should be made with high forge pressure, low friction pressure, and with opportune friction time at which the temperature at whole weld interface reached around 1150 K.     

Characterization of friction stir welded boron carbide particulate reinforced AA6061 aluminum alloy stir cast composite

Development of welding procedures to join aluminum matrix composite (AMCs) holds the key to replace conventional aluminum alloys in many applications. In this research work, AA6061/B₄C AMC was produced using stir casting route with the aid of K₂TiF₆ flux. Plates of 6 mm thickness were prepared from the castings and successfully butt joined using friction stir welding (FSW). The FSW was carried out using a tool rotational speed of 1000 rpm, welding speed of 80 mm/min and axial force of 10 kN. A tool made of high carbon high chromium steel with square pin profile was used. The microstructure of the welded joint was characterized using optical and scanning electron microscopy. The welded joint showed the presence of four zones typically observed in FSW of aluminum alloys. The weld zone showed fine grains and homogeneous distribution of B₄C particles. A joint efficiency of 93.4% was realized under the experimental conditions. But, FSW reduced the ductility of the composite.     

Effects of sleeve plunge depth on microstructures and mechanical properties of friction spot welded alclad 7B04-T74 aluminum alloy

Friction spot welding (FSpW) was applied to join the 7B04-T74 aluminum alloy successfully, and effects of sleeve plunge depth on weld appearance, microstructures and mechanical properties were investigated in detail. When the sleeve plunge depth was larger than 2 mm, a surface indentation with a depth of 0.2 mm should be applied in order to eliminate the defect of annular groove. The tensile shear properties of the joints were dependent on hook geometry, location of alclad layer, and hardness of stir zone (SZ). With increasing the sleeve plunge depth from 2 to 3.5 mm, the hook height increased, the alclad layer downward migrated further and the hardness of SZ decreased. The optimized FSpW joint was obtained when the sleeve plunge depth was 3 mm, and the corresponding tensile shear failure load was 11921 N. Two different failure modes, i.e. shear fracture mode and tensile-shear mixed fracture mode, were observed in the tensile shear tests.     

Defect features and mechanical properties of friction stir lap welded dissimilar AA2024–AA7075 aluminum alloy sheets

5 mm-Thick dissimilar AA2024-T3 and AA7075-T6 aluminum alloy sheets were friction stir lap welded in two joint combinations, i.e., (top) 2024/7075 (bottom) and 7075/2024. The influences of process conditions (welding speed and joint combination) on defects (hook and voids) features and mechanical properties of joints were investigated in detail. It was found that the hook deflects largely upwards into the stir zone (SZ) at lower welding speeds (50, 150 mm/min) in both combinations. The process conditions significantly affect the hook geometry which in return affects the lap shear strength. In all 2024/7075 joints, voids appear and the joints fracture from the tip of hook on AS along the SZ/TMAZ (thermomechanically affected zone) interface in lap shear test (tensile fracture mode). In 7075/2024 joints, the hook on RS horizontally extends a large distance into the bottom stir zone at higher welding speeds (225, 300 mm/min). The joints fracture in three modes: shear fracture along the lap interfaces, tensile fracture and the mix fracture of both. In both joint combinations, the lap shear strength generally increases with the increase of welding speed. 7075/2024 Joints show higher failure load than 2024/7075 joints at lower welding speeds while the opposite result appears at higher welding speeds.     

AA7075 bit for repairing AA2219 keyhole by filling friction stir welding

In the present study, 7.8 mm thick AA2219 rolled plates were successfully filling friction stir welded (FFSW) without keyhole using a semi-consumable tool. The influences of the bit’s geometric parameters and the plunge speed on the joint’s mechanical properties were investigated. Microstructure of the joint, especially at the interface, was observed. The results revealed that the AA7075 bit’s employment was able to decrease the shedding bit material effectively. During tensile tests, the maximum ultimate tensile strength (UTS) and elongation of the joint were 179.6 MPa and 13.7%, equivalent to 96.6% and 99% of the original defect-free friction stir welding (FSW) joint, respectively. The defect-free FFSW joints were produced at lower plunge speeds, and the fracture locations were at the softened region within the heat affected zone (HAZ) adjacent to the thermo-mechanically affected zone (TMAZ) on the retreating side. With increasing the plunge speed, the fracture location was more mainly dependent on the interface strength instead of the hardness distribution.     

Effect of groove design on mechanical and metallurgical properties of quenched and tempered low alloy abrasion resistant steel welded joints

Experimental investigations were carried out to study the influence of three different groove designs on mechanical and metallurgical properties of 15 mm thick Q & T (quenched and tempered) steel welded joints. Welding heat input variation corresponding to each joint configuration was kept to a minimal such that the objective of investigating, exclusively, the effect of varied weld volume on the mechanical and metallurgical performance of these joints could be accomplished. Mechanical performance of these joints was evaluated by subjecting them to transverse tensile testing, and Charpy V-notch impact testing of the weld zones at room temperature and 0 °C. The results of this study reveal that among all types of groove formations used for welding, double-V groove joint possessed maximum YS (yield strength) and UTS (ultimate tensile strength), besides maximum strength ratio (YS/UTS) that was followed by U-groove joint and C-groove joint, respectively. However, weld zone tested individually, for the cover as well as the root pass of the C-groove joint possessed highest CVN (Charpy V-notch) values, both at room temperature and 0 °C. Extensive microhardness studies of these weldments showed a wide variation in the microhardness values of the weld zone and the HAZ (heat affected zone). It was concluded that each groove formation/design exerted a significant influence on the heat dissipation characteristics of these joints, which is evident from different morphological features as revealed through optical microscopy. Scanning electron microscopic studies on tensile and impact tested specimens indicate that despite of achieving undermatched welds that were accompanied with a high degree of metallurgical heterogeneity, the mode of failure in the weld zone was largely ductile.