Properties enhancement using oil palm shell nanoparticles of fibers reinforced polyester hybrid composites

Oil palm shell (OPS) nanoparticles were utilized as filler in fibers reinforced polyester hybrid composites. The OPS nanoparticles were successfully produced from the raw OPS using high-energy ball milling process. Fundamental properties including morphology, crystalline size, and particle size of the OPS nanoparticles were determined. Tri-layer natural fiber reinforcement (kenaf–coconut–kenaf fiber mat) polyester hybrid composites were prepared by hand lay-up techniques. The influences of the OPS nanoparticles loading in the natural fibers reinforced polyester hybrid composites were determined by analyzing physical, mechanical, morphological, and thermal properties of the composites. Results showed that the incorporation of the OPS nanoparticles into the hybrid composites enhanced the composite properties. Further, the natural fibers reinforced polyester hybrid composite had the highest physical, mechanical, morphological, and thermal characteristics at 3 wt.% OPS nanoparticles loading.     

Characteristics of continuous unidirectional kenaf fiber reinforced epoxy composites

Kenaf fibers generally has some advantages such as eco-friendly, biodegradability, renewable nature and lighter than synthetic fibers. The aims of the study are to characterize and evaluate the physical and mechanical properties of continuous unidirectional kenaf fiber epoxy composites with various fiber volume fractions. The composites materials and sampling were prepared in the laboratory by using the hand lay-up method with a proper fabricating procedure and quality control. Samples were prepared based on ASTM: D3039-08 for tensile test and the scanning electron microscopy (SEM) was employed for microstructure analysis to observe the failure mechanisms in the fracture planes. A total of 40 samples were tested for the study. Results from the study showed that the rule of mixture (ROM) analytical model has a close agreement to predict the physical and tensile properties of unidirectional kenaf fiber reinforced epoxy composites. It was also observed that the tensile strength, tensile modulus, ultimate strain and Poisson’s ratio of 40% fiber volume content of unidirectional kenaf fiber epoxy composite were 164 MPa, 18150 MPa, 0.9% and 0.32, respectively. Due to the test results, increasing the fiber volume fraction in the composite caused the increment in the tensile modulus and reduction in the ultimate tensile strain of composite.     

Fabrication and characterization of gum Arabic bonded Rhizophora spp. particleboards

Gum Arabic (GA) was used as a binder for the fabrication of Rhizophora spp. particleboards. The physical and mechanical properties of the bioadhesive bonded particleboards, including moisture content, internal bond (IB) strength, thickness swelling (TS), water absorption (WA) and field-emission scanning electron microscopy (FESEM) were used to characterize the manufactured particleboards. Three different particle sizes of the Rhizophora spp. with four adhesive levels were utilized. Results revealed that the addition of GA into the particleboards noticeably improved panel overall properties. The GA bonded particleboards resulted in smoother surfaces, more rigid texture and better internal bonding strength compared to binderless particleboards made without using any adhesive. All specimens had internal bond strength of more than the minimum requirement of the Japanese Industrial Standard JIS A-5908 Type-8 of 0.15 N/mm² and were noticed to increase by increasing the adhesive level. However the GA bonded particleboards had higher percentage of WA and the TS compared with the binderless boards. Microscopic study also revealed that particleboards bonded with the gum had better contact compared to the binderless boards. Based on these results, it could be concluded that gum Arabic is an effective natural substance that could be added to manufacture particleboards to improve some of panels’ physical and mechanical properties.     

Woven hybrid composites: Tensile and flexural properties of oil palm-woven jute fibres based epoxy composites

In this research, tensile and flexural performance of tri layer oil palm empty fruit bunches (EFB)/woven jute (Jw) fibre reinforced epoxy hybrid composites subjected to layering pattern has been experimentally investigated. Sandwich composites were fabricated by hand lay-up technique in a mould and cured with 105 °C temperatures for 1 h by using hot press. Pure EFB and woven jute composites were also fabricate for comparison purpose. Results showed that tensile and flexural properties of pure EFB composite can be improved by hybridization with woven jute fibre as extreme woven jute fibre mat. It was found that tensile and flexural properties of hybrid composite is higher than that of EFB composite but less than woven jute composite. Statistical analysis of composites done by ANOVA-one way, it showed significant differences between the results obtained. The fracture surface morphology of the tensile samples of the hybrid composites was performed by using scanning electron microscopy.     

Characterization of raw materials and manufactured binderless particleboard from oil palm biomass

The objective of this study was to examine the extractive, holocellulose, alpha cellulose, lignin, starch, and sugar contents of oil palm biomass and to evaluate its suitability in binderless particleboard production. In this study, bark, leaves, fronds, mid-parts and core-parts of the trunks were used to produce experimental binderless particleboard panels. Binderless particleboard panels were made with a target density of 0.80 g/cm³ at a temperature of 180 °C and a pressure of 12 MPa in a computer controlled hot press. The modulus of rupture, the internal bond strength, the thickness swelling and the water absorption of the panels were evaluated. Fourier transform infrared spectroscopy and field emission scanning electron microscopy were used to characterize the properties of the raw materials and the manufactured panels. The chemical composition of the oil palm biomass consisted of high holocellulose, lignin, starch and sugar contents that have been found to aid in the production of binderless particleboard. The core-part of the trunk contained the highest amount of starch and total sugar. Samples made from the core-parts and fronds had sufficient modulus of rupture and internal bond strength to meet the Japanese Industrial Standard. The internal bond strength of the mid-part panels also met the standard. However, binderless board prepared from bark and leaves showed poor modulus of rupture and internal bond strength. Samples from the core-parts had the lowest thickness swell and water absorption but did not meet the above standard. The Fourier transform infrared spectroscopy spectra did not show any substantial difference between the raw materials and the manufactured panels. Field emission scanning electron microscopy indicated that the compressed cells varied between raw material types and showed the presence of compressed cells with some starch granules that facilitated adhesion. Based on the findings of this study, oil palm has the potential to be used to manufacture binderless panel products, and further study is required to improve its dimensional stability.     

Effect of weathering on physical,mechanical and morphological properties of chemically modified wood materials

Physical, mechanical and morphological properties of chemically modified Acaciamangium and Acacia hybrid woods were investigated after weathering. The wood blocks prepared from Acaciamangium and Acacia hybrid, were treated with both propionic anhydride and succinic anhydride. Outdoor (natural) weathering was carried out for 1 year, by exposing the samples to external environmental conditions. Chemical modification enhanced the weathering resistance of Acacia spp. to discoloration, weight loss and mechanical properties. Also, succinic anhydride was better in protecting wood than propionic anhydride modification. Fast growing Acaciamangium and Acacia hybrid may be promising for the use of outdoors following propionic anhydride and succinic anhydride chemical treatments.     

对位芳纶及其复合材料发展思考

对位芳纶是高性能纤维的重要品种,已广泛应用于宇宙探索、航空航天、国防军工、电子通讯、民用建筑等领域。本文根据对位芳纶发展及应用的最新情况,详细介绍了对位芳纶的种类、性能、应用以及发展概况,并结合多年的对位芳纶研发及产业化经验,分析探讨了我国现有对位芳纶及其复合材料产业化发展方面存在的问题,据此提出对位芳纶及其复合材料今后的发展方向和研究重点。最后从科学发展观和低碳经济的角度,指出我国对位芳纶及其复合材料产业化发展的必要性和紧迫性。     

混杂比对碳纤维-玄武岩纤维混杂增强环氧树脂基复合材料弯曲性能的影响

将玄武岩纤维置于混杂铺层的压缩侧,研究了碳纤维-玄武岩纤维混杂增强环氧树脂基复合材料的弯曲性能及混杂比对其弯曲性能的影响。通过对试样进行三点弯曲试验得到了材料的弯曲性能,并通过扫描电子显微镜观察材料的失效模式。与纯碳纤维增强环氧树脂基复合材料相比,当混杂比为16.7%和33.3%时,混杂复合材料的弯曲强度明显提升,弯曲强度分别提高12.4%和15.2%,但是其弯曲模量随着混杂比的提升而降低。混杂后的材料及玄武岩纤维增强环氧树脂基复合材料的失效位移都高于碳纤维增强环氧树脂基复合材料,断裂韧性明显提升。从侧面观察可以发现不同铺层在压缩侧、拉伸侧和中间层有不同的失效形式。      

Chemical composition and molecular structure of fibers from transgenic flax producing polyhydroxybutyrate,and mechanical properties and platelet aggregation of composite materials containing these fibers

In order to improve the properties of flax fibers so that they interact better with the matrix material in composites, several lines of transgenic flax were produced over-expressing the bacterial polyhydroxybutyrate (PHB) synthesis genes. Infra-red spectrophotometry revealed that the cellulose in fibers from the transgenic plants was more highly structured than in fibers from the control plants and PHB was strongly bound to the cellulose of the fibers by covalent ester and hydrogen bonds. The composite containing fibers from transgenic plants was significantly stronger and stiffer than the composites containing fibers from the control plants. Scanning electron microscopy of the fracture surface of composite sheets indicated that fibers from transgenic plants adhered to the polypropylene matrix significantly better. The composite containing fibers from transgenic plants induced almost no platelet aggregation and so may therefore be useful in the construction of biomedical devices that come in contact with blood.     

对位芳纶及其复合材料综述并产业化发展思考

对位芳纶由于其出色的性能,在宇宙探索、航空航天、国防军工、民用建筑等领域有大量的应用,尤其是芳纶复合材料已成为高科技领域必不可少的基础材料。对位芳纶复合材料具有轻质高强等突出特点,因此在节约减排方面具有显著效果,随着全球低碳经济的到来,芳纶及其复合材料的发展前景会越来越好。本文根据对位芳纶发展及应用的最新情况,详细介绍了对位芳纶的种类、性能、应用以及发展概况,并结合多年的对位芳纶研发及产业化经验,分析探讨了我国现有对位芳纶及其复合材料产业化发展方面存在的问题,指出我国在技术、生产效率、生产能力、设备、市场等方面与国外的差距,并据此提出对位芳纶及其复合材料今后的发展方向和研究重点。最后从科学发展观和低碳经济的角度,指出我国对位芳纶及其复合材料产业化发展的必要性和紧迫性。     

Processing and characterization of reinforced polyethylene composites made with lignocellulosic fibers from Egyptian agro-industrial residues

Lignocellulosic fibers were extracted from Egyptian industrial crops, viz. cotton stalk, rice straw, bagasse, and banana plant waste. The chemical composition of these fibers was determined. Composite materials were processed from these natural lignocellulosic fibers using low density polyethylene and acid stearic as compatibilizer, or maleated low density polyethylene. The thermal and mechanical properties were studied by differential scanning calorimetry (DSC) and tensile tests, respectively. The morphology of processed composites was studied by scanning electronic microscopy (SEM). Better compatibility and enhanced mechanical properties were obtained when using maleated LDPE as compatibilizer. The chemical composition of fibers, in terms of lignin, cellulose and hemicelluloses contents, was found to have a strong influence on the mechanical properties of the composites.     

Cellulosic fibers from rice straw and bamboo used as reinforcement of cement-based composites for remarkably improving mechanical properties

The cement-based composites reinforced with cellulosic fibers isolated from rice straw were fabricated by a slurry vacuum de-watering technique. The physical structures and mechanical properties of the composites with fiber contents ranging from 2% to 16% by weight (wt.%) were investigated. Moreover, the composites reinforced with bamboo cellulosic fibers and the control cement paste, sample without cellulosic fibers, were also fabricated as reference materials. As a result, the cement-based composites reinforced by cellulosic fibers showed a remarkable improvement in the mechanical properties. The measurements of the flexural strength and the fracture toughness of the optimal sample were found to be increased by 24.3% and 45 times, respectively. The bulk density of the composites was decreased by 12.4–37.3% as a result of the introduction of cellulosic fibers. Additionally, the field emission scanning electron microscope (FSEM) observations and energy dispersive spectroscopy (EDS) analyses revealed that the hydration products of Portland cement migrated to the fiber lumens, resulting in mineralizing the cellulosic fibers and decreasing the fracture toughness of the composites.     

The effect of crosslinker on mechanical and morphological properties of tropical wood material composites

In this study, wood polymer composites (WPCs) based on five kinds of selected tropical wood species, namely Jelutong (Dyera costulata), Terbulan (Endospermum diadenum), Batai (Paraserianthes moluccana), Rubber (Hevea brasiliensis), and Pulai (Alstonia pneumatophora), were impregnated with methyl methacrylate (MMA) and hexamethylene diisocyanate (HMDIC) monomers mixture in the ratio of 1:1 for composite manufacturing. All these tropical wood reacted with hexamethylene diisocyanate and crosslinked with MMA which enhanced the hydrophobic (restrained water) nature of wood. The vacuum-pressure method was used to impregnate the samples with monomer mixture. The monomer mixture loading achievable was found to be dependent on the properties of wood species. Low loading was observed for the high density wood species. Mechanical strength of fabricated wood polymer composites (WPCs) in term of modulus of elasticity (MOE) and modulus of rupture (MOR) were found to be significantly improved. The wood–polymer interaction was confirmed by Fourier transform infrared (FTIR) spectroscopy. Morphological properties of raw wood and WPC samples were evaluated by scanning electron microscopy (SEM) and XRD analysis and an improvement in morphological properties was also observed for WPC.     

Novel 3D porous multi-phase composite scaffolds based on PCL,thermoplastic zein and ha prepared via supercritical CO2 foaming for bone regeneration

The aim of this study was the design of novel biodegradable porous scaffolds for bone tissue engineering (bTE) via supercritical CO₂ (scCO₂) foaming process. The porous scaffolds were prepared from a poly(ε-caprolactone)-thermoplastic zein multi-phase blend w/o interdispersed hydroxyapatite particles (HA) and the porous structure achieved via the scCO₂ foaming technology. The control of scaffolds porosity was obtained by modulating materials formulation and foaming temperature (T_F). The scaffolds were subjected to morphological, micro-structural and biodegradation analyses, as well as in vitro biocompatibility tests. Results demonstrated that both HA concentration and T_F significantly affected the micro-structural features of the scaffolds. In particular, scaffolds with porosity and pore size distribution, mechanical properties and biodegradability adequate for bTE were designed and produced by selecting a T_F equal to 100 °C for all the compositions used. The biocompatibility of these scaffolds was assessed in vitro by using osteoblast-like MG63 and human mesenchymal stem cells (hMSCs).     

Potentiality of artificially aged aluminium 6061 hybrid composites reinforced with granite and graphite micro–fillers for structural applications

The current study explores the feasibility of artificial aging treatment to aluminium alloy 6061 hybrid composites reinforced with graphite and fine granite particulates to suit structural applications. Aging at 100 °C retrieved a better response of the hybrid composites as compared to that at 150 °C in terms of peak hardness and strength. Among the five different stir‐cast compositions, the composition of aluminium 6061 with 2 wt. % graphite and 4 wt. % granite showed enhanced mechanical properties than that of the base alloy as well as mono reinforcement type composites which was attribued to the formation of rod‐shaped β‐Mg₂Si precipitates.     

Biomicrofibrilar composites of high density polyethylene reinforced with curauá fibers: Mechanical,interfacial and morphological properties

Vegetal fibers are used in polymer composites to improve mechanical properties, substituting inorganic reinforcing agents produced by non renewable resources, like fiberglass. The highest performance formulation in high density polyethylene, HDPE, composites reinforced with curauá fibers were studied, aiming to improve the interphase interaction and optimize the mechanical properties. The fiber content, the type and the concentration of coupling agent were tested. The composites and the pure materials were characterized by Fourier transform infrared spectroscopy and the fiber/matrix phase adhesion was evaluated by scanning electron microscopy. The mechanical properties and the micrographs showed that the best formulation is: 20 wt.% of milled curauá fibers and 2 wt.% poly(ethylene-g-maleic anhydride). The coupled composites are also less hygroscopic than the uncoupled composites. We conclude that the composites reinforced with curauá fibers have mechanical properties comparable to commercially produced composites of HDPE reinforced with fiberglass.     

Stiffness and vibration characteristics of SMA/ER3 composites with shape memory alloy short fibers

Shape memory alloys (SMAs) possess both sensing and actuating functions due to their shape memory effect, pseudo-elasticity, high damping capability and other remarkable characteristics. Combining the unique properties of SMAs with other materials can create intelligent or smart composites. In this paper, epoxy resin composites filled with Ni–Ti alloy short fibers were developed. Microstructure was observed using digital HF microscope. The dynamic mechanical properties were investigated by measuring the first vibration mode of clamped cantilever beams and by dynamic mechanical analysis (DMA). Moreover, the natural frequency of SMA composites was predicted theoretically. As a result, the temperature dependency of vibration property and DMA characteristics is affected largely due to the addition of SMA short fibers. The vibrational characteristics of SMA composites can be improved by the addition of small amounts of SMA short fibers. The addition of 3.5 wt.% of SMA short fiber content to epoxy resin resulted in the maximum increment in both natural frequency and storage modulus. This suggested that there exists an optimum SMA fiber content for vibration characteristics.     

Influence of fiber content on mechanical,morphological and thermal properties of kenaf fibers reinforced poly(vinyl chloride)/thermoplastic polyurethane poly-blend composites

Kenaf (Hibiscus Cannabinus) bast fiber reinforced poly(vinyl chloride) (PVC)/thermoplastic polyurethane (TPU) poly-blend was prepared by melt mixing method using Haake Polydrive R600 internal mixer. The composites were prepared with different fiber content: 20%, 30% and 40% (by weight), with the processing parameters: 140 °C, 11 min, and 40 rpm for temperature, time and speed, respectively. After mixing, the composite was compressed using compressing molding machine. Mechanical properties (i.e. tensile properties, flexural properties, impact strength) were studied. Morphological properties of tensile fracture surface were studied using Scanning electron microscope (SEM). Thermal properties of the composites were studied using Thermogravimetric Analyses (TGA). PVC/TPU/KF composites have shown lower tensile strength and strain with increase in fiber content. Tensile modulus showed an increasing trend with increase in fiber content. Impact strength decreased with increase in fiber content; however, high impact strength was observed even with 40% fiber content (20.2 kJ/m²). Mean while; the 20% and 30% fiber contents showed higher impact strength of 34.9, 27.9 kJ/m²; respectively. SEM showed that there is poor fiber/matrix adhesion. Thermal degradation took place in three steps. In the first step, composites as well as the matrix had a similar stability. At the second step, matrix showed a slightly better stability than the composites. At the last step, composites showed a better stability than the matrix.     

Tensile and flexural properties of snake grass natural fiber reinforced isophthallic polyester composites

Natural fiber composite materials are one such capable material which replaces the conventional and synthetic materials for the practical applications where we require less weight and energy conservation. The present paper, which emphasis the importance of the newly identified snake grass fibers which are extracted from snake grass plants by manual process. In this paper, the tensile properties of the snake grass fiber are studied and compared with the traditionally available other natural fibers. The mixed chopped snake grass fiber reinforced composite is prepared by using the isophthallic polyester resin and the detailed preparation methodology is presented. Fiber pull-outs on the fractured specimen during the physical testing of the composites are also investigated. The experimental evidence also shows that the volume fraction increases the tensile, flexural strength and modulus of the snake grass fiber reinforce composite.     

Manufacture and characterisation of thermoplastic composites made from PLA/hemp co-wrapped hybrid yarn prepregs

PLA/hemp co-wrapped hybrid yarns were produced by wrapping PLA filaments around a core composed of a 400 twists/m and 25 tex hemp yarn (Cannabis sativa L) and 18 tex PLA filaments. The hemp content varied between 10 and 45 mass%, and the PLA wrapping density around the core was 150 and 250 turns/m. Composites were fabricated by compression moulding of 0/90 bidirectional prepregs, and characterised regarding porosity, mechanical strength and thermal properties by dynamic mechanical thermal analysis (DMTA) and differential scanning calorimetry (DSC). Mechanical tests showed that the tensile and flexural strengths of the composites markedly increased with the fibre content, reaching 59.3 and 124.2 MPa when reinforced with 45 mass% fibre, which is approximately 2 and 3.3 times higher compared to neat PLA. Impact strength of the composites decreased initially up to 10 mass% fibre; while higher fibre loading (up to 45 mass%) caused an increase in impact strength up to 26.3 kJ/m², an improvement of about 2 times higher compared to neat PLA. The composites made from the hybrid yarn with a wrapping density of 250 turns/m showed improvements in mechanical properties, due to the lower porosity. The fractured surfaces were investigated by scanning electron microscopy to study the fibre/matrix interface.