Effects of initial grain size on hot deformation behavior of commercial pure aluminum

The effects of initial grain size of commercial pure aluminum on hot deformation behavior were investigated using hot compression tests. The hot compression tests were carried out on the pure aluminum samples with the initial grain sizes of 50, 150 and 450 μm using various strains, strain rates and different deformation temperatures. It was found that the hot deformation behavior of used material was sensitive to deformation conditions and initial microstructure. Results indicate that the initial grain size has significant effect on the flow stress. Flow stress decreases when the grain size decreases from 450 to 50 μm and when strain rate is lower than 0.05 s⁻¹. This procedure is reversed at strain rate of 0.5 s⁻¹. Furthermore, effects of other parameters like the strain rates and deformation temperatures on the flow stresses and hardening rates were investigated. It was also found that the inhomogeneity of microstructure distribution at different positions of the deformed specimens depended on the amount of deformation concentration at particular points and other processing parameters such as initial grain sizes, strain rates and deformation temperatures. In addition the geometric dynamic recrystallization (GDRX) was observed in the specimens highly strained (0.7) at elevated temperature (500 °C) using polarized light microscope and sensitive tint (PLM + ST).     

Quantification of bake hardening effect in DP600 and TRIP700 steels

Recently developed advanced high-strength steels with multiphase microstructures show interesting bake-hardening (BH) properties. This research work aims to quantify the effect of BH on dual-phase (DP) and transformation induced plasticity (TRIP) steel. Different pre-strains from 0% to 10% with a subsequent BH annealing cycle with temperatures of 60–220 °C for varying BH holding times from 1 to 10,000 min were applied for both materials. Mechanical properties such as yield and tensile strengths, elongation and BH values in dependency of the BH parameters have been determined and related to specific microstructural features in order to characterize the age and strain hardening behavior.     

Microstructure characteristic for high temperature deformation of powder metallurgy Ti–47Al–2Cr–0.2Mo alloy

Hot compression tests of a powder metallurgy (P/M) Ti–47Al–2Cr–0.2Mo (at. pct) alloy were carried out on a Gleeble-3500 simulator at the temperatures ranging from 1000 °C to 1150 °C with low strain rates ranging from 1 × 10⁻³ s⁻¹ to 1 s⁻¹. Electron back scattered diffraction (EBSD), scanning electron microscope (SEM) and transmission electron microscope (TEM) were employed to investigate the microstructure characteristic and nucleation mechanisms of dynamic recrystallization. The stress–strain curves show the typical characteristic of working hardening and flow softening. The working hardening is attributed to the dislocation movement. The flow softening is attributed to the dynamic recrystallization (DRX). The number of β phase decreases with increasing of deformation temperature and decreasing of strain rate. The ratio of dynamic recrystallization grain increases with the increasing of temperature and decreasing of strain rate. High temperature deformation mechanism of powder metallurgy Ti–47Al–2Cr–0.2Mo alloy mainly refers to twinning, dislocations motion, bending and reorientation of lamellae.     

Quantitative Analysis of Work Hardening and Dynamic Softening Behavior of low carbon alloy Steel Based on the Flow Stress

In this study, the constitutive equation and DRX(Dynamic recrystallization) model of Nuclear Pressure Vessel Material 20MnNiMo steel were established to study the work hardening and dynamic softening behavior based on the flow behavior, which was investigated by hot compression experiment at temperature of 950 °C, 1050 °C, 1150 °C and 1250 °C with strain rate of 0.01 s⁻¹, 0.1 s⁻¹ and 10 s⁻¹ on a thermo-mechanical simulator THE RMECMASTOR-Z. The critical conditions for the occurence of dynamic recrystallization were determined based on the strain hardening rate curves of 20MnNiMo steel. Then the model of volume fraction of DRX was established to analyze the DRX behavior based on flow curves. At last, the strain rate sensitivity and activation volume V^* of 20MnNiMo steel were calculated to discuss the mechanisms of work hardening and dynamic softening during the hot forming process. The results show that the volume fraction of DRX is lower with the higher value of Z (Zener–Hollomon parameter), which indicated that the DRX fraction curves can accurately predicte the DRX behavior of 20MnNiMo steel. The storage and annihilation of dislocation at off-equilibrium saturation situation is the main reason that the strain has significant effects on SRS(Strain rate sensitivity) at the low strain rate of 0.01 s⁻¹ and 0.1 s⁻¹. While, the effects of temperature on the SRS are caused by the uniformity of microstructure distribution. And the cross-slip caused by dislocation piled up which beyond the grain boundaries or obstacles is related to the low activation volume under the high Z deformation conditions. Otherwise, the coarsening of DRX grains is the main reason for the high activation volume at low Z under the same strain conditions.     

Hot deformation behavior of a Nb-containing 316LN stainless steel

A Nb-containing 316LN stainless steel was compressed in the temperature range 900–1200 °C and strain rate range 0.01–10 s^?1. The mechanical behavior has been characterized using stress–strain curve analysis, kinetic analysis, processing maps, etc. The microstructural evolution was observed and the mechanism of flow instability was discussed. It was found that the work hardening rate and flow stress decreased with increasing deformation temperature and decreasing strain rate. On the contrary, the efficiency of power dissipation increased with them; Flow instability was manifested as cracking and flow localization; The hot deformation equation and the relationships between deformation condition and dynamic recrystallization grain size and fraction were obtained; For Nb-containing 316LN stainless steel, the favorite nucleation sites for dynamic recrystallization are in sequence of triple point, grain boundary, twin boundary and intragranular deformation band; The suggested processing window is given.     

Constitutive modeling for flow stress of 55SiMnMo bainite steel at hot working conditions

The hot deformation behavior of 55SiMnMo bainite steel was studied through isothermal hot compression tests conducted using a Gleeble 3500 at 950–1100 °C, with strain rates of 0.01 s⁻¹ to 10 s⁻¹. A constitutive equation was established using the experimental results to describe the stress–strain relationship based on the dislocation density variation, considering the influence of the dynamic softening mechanism. When dynamic recovery is the only softening mechanism, a constitutive equation for flow stress was obtained from the variation of the dislocation density during hot deformation based on work hardening and dynamic recovery. When dynamic recrystallization occurs, the relationship between the dislocation density and the volume fraction of dynamic recrystallization was used to predict the flow stress after the peak. The reliability of the model was verified through a comparison between the predicted flow stress curves from the model and the experimental data.     

Effect of thermo-mechanical treatment on properties improvement and microstructure changes in copper–gold alloy

This paper reports on the changes in hardness, microhardness, electrical conductivity and microstructure using the optical and scanning electron microscopy of the copper-based alloy with 4.5 at.% gold, during the complex thermo-mechanical treatment, which is used to create the conditions for development of anneal hardening effect. It was shown that the increase of deformation degree during both the prefinal and final rolling resulted in the increase of hardness, microhardness and electrical conductivity values, due to changes in the microstructure caused by the cold plastic deformation. The differences in the initial microstructure of the homogenized and quenched samples created the different deformation strengthening rates. Low-temperature annealing of the finally rolled samples contributed to a further increase of the above properties due to the anneal hardening effect. The improvement of the properties during the annealing was accomplished in two stages, and the best combination of properties was achieved in the second stage of hardening after annealing at 260 °C. Minor changes in the microstructure were noticeable during the annealing at 260 °C, but the EDS analysis showed a significant change in the concentration of gold atoms within the grain.     

A characterization for the flow behavior of 42CrMo steel

In order to evaluate the flow stress and the dynamic softening characteristics of casting 42CrMo steel, isothermal upsetting experiments with height reduction 60% were performed at the temperatures of 1123 K, 1198 K, 1273 K and 1348 K, and the strain rates of 0.01 s⁻¹, 0.1 s⁻¹, 1 s⁻¹ and 10 s⁻¹ on thermal physics simulator Gleeble 1500. The flow behavior of the applied stress as a function of strain, strain rate and temperature exhibits a more pronounced effect of temperature than strain rate, and a typical characteristic of dynamic recrystallization softening. To characterize the flow behavior more factually and accurately, the traditional Fields–Backofen equation was amended, and an innovative mathematical model containing a softening item s, n-value and m-value variable functions was brought forth. The stress–strain curves calculated by the derived flow stress equation are fit with the experimental results well not only at the hardening stage but also at softening stage.     

Effect of processing parameters on the hot deformation behavior of as-cast TC21 titanium alloy

Isothermal compression tests of as-cast Ti–6A1–2Zr–2Sn–3Mo–1Cr–2Nb (TC21) titanium alloy are conducted in the deformation temperature ranging from 1000 to 1150 °C with an interval of 50 °C, strain rate ranging from 0.01 to 10.0 s⁻¹ and height reductions of 30%, 45%, 60% and 75% on a computer controlled Gleeble 3500 simulator. The true stress–strain curves under different deformation conditions are obtained. Based on the experimental data, the effects of deformation parameters on the hot deformation behavior of as-cast TC21 alloy were studied. The deformation mechanisms of the alloy in the whole regimes are predicted by the power dissipation efficiency and instability parameter and further investigated through the microstructure observation. It is found that at the height reductions of 30%, 45% and 60%, the softening of stress–strain curves at high strain rate (>1.0 s⁻¹) is mainly associated with flow localization, which is caused by local temperature rise, whereas at low strain rate, the softening is associated with dynamic recrystallization (DRX). However, the instability showed in flow localization occurs at low strain rate of 0.01 s⁻¹ when the height reduction reaches 75%. In addition, the effects of strain rate, deformation temperature and height reduction on microstructure evolution are discussed in detail, respectively.     

Dynamic recrystallization behavior of an as-cast TiAl alloy during hot compression

High temperature compressive deformation behaviors of as-cast Ti–43Al–4Nb–1.4W–0.6B alloy were investigated at temperatures ranging from 1050 °C to 1200 °C, and strain rates from 0.001 s^− 1 to 1 s^− 1. Electron back scattered diffraction technique, scanning electron microscopy and transmission electron microscopy were employed to investigate the microstructural evolutions and nucleation mechanisms of the dynamic recrystallization. The results indicated that the true stress–true strain curves show a dynamic flow softening behavior. The dependence of the peak stress on the deformation temperature and the strain rate can well be expressed by a hyperbolic-sine type equation. The activation energy decreases with increasing the strain. The size of the dynamically recrystallized β grains decreases with increasing the value of the Zener–Hollomon parameter (Z). When the flow stress reaches a steady state, the size of β grains almost remains constant with increasing the deformation strain. The continuous dynamic recrystallization plays a dominant role in the deformation. In order to characterize the evolution of dynamic recrystallization volume fraction, the dynamic recrystallization kinetics was studied by Avrami-type equation. Besides, the role of β phase and the softening mechanism during the hot deformation was also discussed in details.     

Deformation behavior and microstructure evolution in multistage hot working of TA15 titanium alloy: on the role of recrystallization

Interrupted compression tests of TA15 titanium alloy with initially equiaxed microstructure were carried out at deformation temperatures between 1173 to 1273 K and strain rates between 0.001 to 0.1 s⁻¹ to investigate the deformation behavior and microstructure evolution under multistage deformation. The TA15 alloy exhibits significant flow softening in both β and (α + β) working. It is found that the flow softening relates to dynamic recrystallization of β phases under current experimental conditions. In multistage β working, metadynamic recrystallization is the main softening mechanism during inter-pass holding. The grain refinement by metadynamic recrystallization leads to the decrease in peak stress upon reloading. In multistage (α + β) working, static recrystallization is the main softening mechanism during inter-pass holding. The static recrystallization kinetics increases with temperature and strain rate. The inter-pass holding has little influence on the morphology of the primary α phases. The β grain size is determined by spacing of primary α phases, which is more affected by working temperature but less dependent on strain rate and inter-pass holding time.     

The influence of initial microstructure and temperature on the deformation behavior of AZ91 magnesium alloy

The deformation behavior of AZ91 magnesium alloy has been investigated using uniaxial compression tests at a temperature range of 100–300 °C. The different processing routes including homogenization treatment, hot rolling and annealing have been employed to study the effect of initial microstructure on the compressive mechanical response of the AZ91 alloy. The results show that the hot-rolled material presents an enhanced compressive workability at temperatures as low as 100 °C. The experimental alloy exhibit dynamic recrystallization during compression in any of the initial microstructures. The maximum and minimum DRX (dynamic recrystallization) fraction has been obtained in hot-rolled and homogenized conditions, respectively. The recrystallized fraction increases with raising the temperature. In addition the effect of initial microstructure on the peak stress diminishes with increasing temperature while its effect on the peak strain remains remarkable. The softening fraction has been increased with temperature, where a pronounced effect has been recorded in the case of homogenized (un-rolled) material.     

Electron backscatter diffraction study of deformation and recrystallization textures of individual phases in a cross-rolled duplex steel

The evolution of microstructure and texture during cross-rolling and annealing was investigated by electron backscatter diffraction in a ferritic–austenitic duplex stainless steel. For this purpose an alloy with nearly equal volume fraction of the two phases was deformed by multi-pass cross-rolling process up to 90% reduction in thickness. The rolling and transverse directions were mutually interchanged in each pass by rotating the sample by 90° around the normal direction. In order to avoid deformation induced phase transformation and dynamic strain aging, the rolling was carried out at an optimized temperature of 898 K (625 °C) at the warm-deformation range. The microstructure after cross warm-rolling revealed a lamellar structure with alternate arrangement of the bands of two phases. Strong brass and rotated brass components were observed in austenite in the steel after processing by cross warm-rolling. The ferrite in the cross warm-rolling processed steel showed remarkably strong RD-fiber (RD//< 011 >) component {001}< 011 >. The development of texture in the two phases after processing by cross warm-rolling could be explained by the stability of the texture components. During isothermal annealing of the 90% cross warm-rolling processed material the lamellar morphology was retained before collapse of the lamellar structure to the mutual interpenetration of the phase bands. Ferrite showed recovery resulting in annealing texture similar to the deformation texture. In contrast, the austenite showed primary recrystallization without preferential orientation selection leading to the retention of deformation texture. The evolution of deformation and annealing texture in the two phases of the steel was independent of one another.     

Hot deformation behavior and workability characteristics of bimodal size SiCp/AZ91 magnesium matrix composite with processing map

The hot deformation behavior of (0.2 um 1.5 vol.% + 10 um8.5 vol.%) bimodal size SiCp/AZ91 magnesium matrix composite fabricated by stir casting was investigated at the temperature of 270–420 °C and strain rate of 0.001–1 S⁻¹. The flow stress at the strain of 0.5 was used for kinetic analysis. Results indicate that dislocation climb is likely to be the main deformation mechanism responsible for the present composite. By evaluating the efficiencies of power dissipation and instability parameters, the processing maps are developed to optimize the hot working processing. Two domains of dynamic recrystallization are found in the processing map. One exists at the temperature of 270–370 °C and strain rate of 0.001–0.01 s⁻¹ with maximum dissipation efficiency of 38%; the other exists at 420 °C and 0.01 s⁻¹ with peak dissipation efficiency of 24%. The instability region of flow behavior can also be recognized at the temperature of 270–320 °C and the strain rate of 0.1–1 s⁻¹. The characteristic microstructures predicted from the processing map agree well with the result of microstructure observations.     

Hot deformation and processing map of an as-extruded Mg–Zn–Mn–Y alloy containing I and W phases

The hot deformation characteristics of an as-extruded ZM31 (Mg–Zn–Mn) magnesium alloy with an addition of 3.2 wt.% Y, namely ZM31 + 3.2Y, have been studied via isothermal compression testing in a temperature range of 300–400 °C and a strain rate range of 0.001–1 s^− 1. A constitutive model based on hyperbolic-sine equation along with processing maps was used to describe the dependence of flow stress on the strain, strain rate, and deformation temperature. The flow stress was observed to decrease with increasing deformation temperature and decreasing strain rate. The deformation activation energy of this alloy was obtained to be 241 kJ/mol. The processing maps at true strains of 0.1, 0.2, 0.3 and 0.4 were generated to determine the region of hot workability of the alloy, with the optimum hot working parameters being identified as deformation temperatures of 340–500 °C and strain rates of 0.001–0.03 s^− 1. EBSD examinations revealed that the dynamic recrystallization occurred more extensively and the volume fraction of dynamic recrystallization increased with increasing deformation temperature. The role of element Y and second-phase particles (I- and W-phases) during hot compressive deformation was discussed.     

Study on hot workability and optimization of process parameters of a modified 310 austenitic stainless steel using processing maps

To investigate the optimized hot deformation parameters of a modified 310 austenitic stainless steel, the hot compression tests were performed using a Gleeble 3500 thermal simulator. The hot deformation behavior and hot workability characteristics were investigated in a temperature range of 800–1100 °C and a strain rate range of 0.1–10 s⁻¹. The hot processing maps of the tested steel were developed based on the dynamic material model (DMM), from which the safe deformation regions and instable deformation regions were determined. The corresponding microstructural and hardness evolutions during deformation were analyzed in detail. It was found that the deformation in the safe regions was beneficial to dynamic recovery (DRY) and dynamic recrystallization (DRX), while the deformation in unstable region would lead to flow instability, kink boundaries and grain growth. Near 950 °C, the energy dissipation rates were unusually lower, and the hardness of the deformed sample exhibited a significant increase, as a result of strain-induced precipitation. Coupled with the microstructure analysis and processing map technology, the workability map was schematically plotted and the optimal working conditions were determined. Such conditions were: temperatures in the range of 1075–1100 °C and strain rates in the range of 0.5–1.7 s⁻¹. These conditions are critical to attain an excellent homogeneous microstructure with fine grains after deformation for the modified 310 austenitic stainless steel.     

Effects of microstructure changes on the superplasticity of 2205 duplex stainless steel

The high temperature deformation behavior of 2205 duplex stainless steel under different conditions had been studied by tensile tests. The whole tensile test was conducted at a constant temperature 950 °C with an initial strain rate 1.5 × 10⁻³/s. Some tests were interrupted purposely and then the samples were quenched using water. Elongations of the fractured specimens were calculated. Microstructure changes just before and during the deformation were observed. Phase ratio of σ precipitate was analyzed. The results showed that the superplasticity of 2205 duplex stainless steel was directly affected by the microstructure before the deformation. The recrystallization phenomenon was distinct along with the homogenizing time and the grains became equiaxed and stable. Meanwhile, the quantity of σ phase increased when prolonged the homogenizing time. After homogenized for 7 min before the tensile test, the σ phase ratio was about 4.8% and the grain size was about 998 nm, the maximum elongation value 1260% was obtained. During the deformation progress, dynamic recrystallization was observed and quantity of σ phase increased with the increasing of deformation strain. The σ phase restricted the grain growth and kept the equiaxed duplex structure stable with a grain size of about 1 μm.     

Grain growth and microstructure evolution based mechanical property predicted by a modified Hall–Petch equation in hot worked Ni76Cr19AlTiCo alloy

The deformation behavior of Ni76Cr19AlTiCo has been investigated under compressive strains by up to 50% at temperatures ranging from 800 °C to 1150 °C, and at strain rates from 0.001 s⁻¹ to 1 s⁻¹. A dramatic change in the mechanical properties of the alloy was observed when the temperature was increased from 850 °C to 950 °C, along with a rapid increase in grain size with increasing the temperature. Recovery and recrystallization processes occurred under deformation at temperatures above 950 °C. The degree of recrystallization was found to increase with increasing temperature or decreasing strain rate. γ′-phase precipitation occurred in the matrix and the particle sizes and the number of the precipitated phases were found to increase with increasing temperature or decreasing strain rate. Grain boundary precipitation of chromium carbides has also been observed, but its influence was negligible because of the small amount of the precipitates present in the matrix.A modified Hall–Petch equation was proposed to predict the mechanical properties of the alloy based on grain growth and microstructure evolution.     

Effect of strain-induced precipitation on the low angle grain boundary in AA7050 aluminum alloy

Effects of the particles induced by strain on dynamic recrystallization and microstructure of the AA7050 aluminum alloy were investigated during hot deformation using X-ray diffraction (XRD), transmission electron microscopy (TEM) and electron back-scattered diffraction (EBSD). Experimental results showed that partial recrystallized grains containing little sub-structure were produced during the solution treatment. Numerous particles were successfully obtained by the strain-induced precipitation during first-pass deformation at 573 K. The deformation promoted spheroidization and refinement of the precipitate particles. Then these particles pinned dislocations and grain boundaries inhibiting dynamic recrystallization during second-pass high-temperature deformation at 673 K and low angle grain boundary fraction was increased significantly to 83.8%. Furthermore, the tensile test indicated that microstructure with numerous low angle boundaries (LAGBs) and 5 μm sub-grains had increased the strength and ductility of the AA7050 aluminum alloy.