Microstructure,mechanical and corrosion properties and biocompatibility of Mg–Zn–Mn alloys for biomedical application

Mn and Zn were selected to develop a Mg–Zn–Mn magnesium alloy for biomedical application due to the good biocompatibility of Zn and Mn elements. Microstructure, mechanical properties, corrosion properties and biocompatibility of the Mg–Zn–Mn alloys have been investigated by use of optical microscope, scanning electron microscope, tensile testing, and blood hemolysis and cell toxicity. Microstructure observation has shown that the addition of Zn and the extrusion significantly refined the grain size of both the as-cast and the extruded magnesium alloys, which mainly contributes to the high tensile strength and good elongation. Polarization test has shown Zn could accelerate the formation of a passivation film, which provides good protection to the magnesium alloy against simulate body fluid. Cell culture and hemolysis tests have shown that the magnesium alloy did not have cell toxicity, showing good cytocompatibility, but the alloy caused hemolysis to blood system. It was suggested that surface modification have to be adopted to improve the blood compatibility of the magnesium alloy for the application in blood environment.     

Phosphating treatment and corrosion properties of Mg–Mn–Zn alloy for biomedical application

A phosphating treatment was applied to Mg–Mn–Zn alloy in order to improve the corrosion resistance. Surface morphology and phase constitute were observed and identified by SEM, EDS, SAXS, XRD and XPS. SEM observation showed that a rough and crystalline reaction layer was formed on the surface of Mg alloy. With the increasing of phosphating time, the layer became thicker and denser. It has been showed that the reaction layer was mainly composed of brushite (CaHPO₄ · 2H₂O). Small amount of Zn²⁺ was also detected by XPS and EDS. The corrosion resistance of the phosphated samples was measured by the electrochemical polarization and the immersion test in comparison with the bare alloy. The results manifested that the corrosion resistance of Mg alloy was improved by the phosphating treatment, and the corrosion resistance increased with the increase of the phosphating time within 50 min. Immersion tests showed that the phosphate layer could protect magnesium alloy from fast corrosion. The brushite layer has been transformed into hydroxyapatite (HA) during the immersion in the simulated body fluid (SBF) solution, which suggested the brushite layer could provide good biocompatibility.     

Enhancing mechanical properties of Mg–Sn alloys by combining addition of Ca and Zn

We developed new wrought Mg–2Sn–1Ca wt.% (TX21) and Mg–2Sn–1Ca–2Zn wt.% (TXZ212) alloys with high strength and ductility simultaneously, produced by conventional casting, homogenization and indirect extrusion. A partial dynamically recrystallized microstructure, with the micron-/nano-MgSnCa particles and G.P. zones dispersing, was obtained in TX21 alloy extruded at 260 °C (TX21-260). The TX21-260 alloy exhibited yield strength (YS) of 269 MPa, ultimate tensile strength (UTS) of 305 MPa, while those of the TX21 alloy extruded at 300 °C decreased to be 207 MPa and 230 MPa respectively. For TXZ212-260 alloy, on the other hand, MgSnCa, MgZnCa and MgZn₂ phases were observed, and the average grain size increased to be ∼5 μm. The YS and UTS of TXZ212-260 alloy evolved to be 218 MPa and 285 MPa, and the elongation (EL) reached as high as 23%. The high strengths of TX21-260 alloy were expected due to the high number density of nano-MgSnCa phases, G.P. zones and ultra-fine grain size (∼0.8 μm). The high EL of 23% in TXZ212-260 alloy was consistent with the high work-hardening rate, which was attributed to the larger grain size, more high angular grain boundaries, presence of more nano-particles and the weaker texture.     

Effects of Sn on microstructure and mechanical properties of as-rolled Mg–5Zn–1Mn alloy

Effects of Sn on microstructure and mechanical properties of Mg–5Zn–1Mn alloy subjected to high strain rate rolling (9.1?s^-1), 300°C and 80% pass reduction are investigated. With higher Sn content, the dynamic recrystallisation (DRX) grain size gradually decreases due to the stronger pinning of nano-scale precipitates at grain boundaries and the DRX fraction first increases due to the enhanced effect on DRX by decreasing stacking fault energy and then decreases due to more precipitates at grain boundaries. Ultimate tensile strength (UTS) and elongation to rupture (Er) of as-rolled alloys increase and then decrease. Alloy with 0.9 mass% Sn exhibits the highest DRX fraction (95?vol.-%), the finer DRX grain size (1.22?µm), UTS of 358?MPa and Er of 20.4%.     

Effects of Ca on microstructure, mechanical and corrosion properties and biocompatibility of Mg–Zn–Ca alloys

Zn and Ca were selected as alloying elements to develop an Mg–Zn–Ca alloy system for biomedical application due to their good biocompatibility. The effects of Ca on the microstructure, mechanical and corrosion properties as well as the biocompatibility of the as-cast Mg–Zn–Ca alloys were studied. Results indicate that the microstructure of Mg–Zn–Ca alloys typically consists of primary α-Mg matrix and Ca₂Mg₆Zn₃/Mg₂Ca intermetallic phase mainly distributed along grain boundary. The yield strength of Mg–Zn–Ca alloy increased slightly with the increase of Ca content, whilst its tensile strength increased at first and then decreased. Corrosion tests in the simulated body fluid revealed that the addition of Ca is detrimental to corrosion resistance due to the micro-galvanic corrosion acceleration. In vitro hemolysis and cytotoxicity assessment disclose that Mg–5Zn–1.0Ca alloy has suitable biocompatibility.     

Effects of Zn on microstructure,mechanical properties and corrosion behavior of Mg–Zn alloys

In this study, binary Mg–Zn alloys were fabricated with high-purity raw materials and by a clean melting process. The effects of Zn on the microstructure, mechanical property and corrosion behavior of the as-cast Mg–Zn alloys were studied using direct observations, tensile testing, immersion tests and electrochemical evaluations. Results indicate that the microstructure of Mg–Zn alloys typically consists of primary α-Mg matrix and MgZn intermetallic phase mainly distributed along grain boundary. The improvement in mechanical performances for Mg–Zn alloys with Zn content until 5% of weight is corresponding to fine grain strengthening, solid solution strengthening and second phase strengthening. Polarization test has shown the beneficial effect of Zn element on the formation of a protective film on the surface of alloys. Mg–5Zn alloy exhibits the best anti-corrosion property. However, further increase of Zn content until 7% of weight deteriorates the corrosion rate which is driven by galvanic couple effect.     

Improvement of mechanical properties and corrosion resistance of biodegradable Mg–Nd–Zn–Zr alloys by double extrusion

Mg–Nd–Zn–Zr alloy is a novel and promising biodegradable magnesium alloy due to good biocompatibility, desired uniform corrosion mode and outstanding corrosion resistance in simulated body fluid (SBF). However, the corrosion resistance and mechanical properties should be improved to meet the requirement of the biodegradable implants, such as plates, screws and cardiovascular stents. In the present study, double extrusion process was adopted to refine microstructure and improve mechanical properties of Mg–2.25Nd–0.11Zn–0.43Zr and Mg–2.70Nd–0.20Zn–0.41Zr alloys. The corrosion resistance of the alloys after double extrusion was also studied. The results show that the microstructure of the alloys under double extrusion becomes much finer and more homogeneous than those under once extrusion. The yield strength, ultimate tensile strength and elongation of the alloys under double extrusion are over 270 MPa, 300 MPa and 32%, respectively, indicating that outstanding mechanical properties of Mg–Nd–Zn–Zr alloy can be obtained by double extrusion. The results of immersion experiment and electrochemical measurements in SBF show that the corrosion resistance of Alloy 1 and Alloy 2 under double extrusion was increased by 7% and 8% respectively compared with those under just once extrusion.     

Improving mechanical properties of age-hardenable Mg–6Zn–4Al–1Sn alloy processed by double-aging treatment

Microstructure and mechanical properties of a new high-strength Mg–6 Zn–4 Al–1 Sn alloy were investigated. Microstructure of the as-cast Mg alloy exhibited partially divorced characteristics. The dendritic structure of the Mg–6 Zn–4 Al alloy was significantly refined with the addition of 1%(in weight) Sn, but Mg2 Sn phases were not formed. In addition, an icosahedral quasi-crystal phase was formed in the as-cast Mg–6 Zn–4 Al–1 Sn alloy. It was found that after the double-aging treatment through two different heat treatments on the Mg–6 Zn–4 Al–1 Sn alloy, the precipitates were finer and far more densely dispersed in the matrix compared with single-aged counterpart, resulting in a significant improvement in tensile strength with yield strength, ultimate tensile strength and elongation of 175 MPa, 335 MPa and 11%,respectively.     

Microstructures, mechanical properties and in vitro corrosion behaviour of biodegradable Mg–Zr–Ca alloys

The microstructures, mechanical properties, corrosion behaviour and biocompatibility of the Mg–Zr–Ca alloys have been investigated for potential use in orthopaedic applications. The microstructures of the alloys were examined using X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The mechanical properties of Mg–Zr–Ca alloys were determined from compressive tests. The corrosion behaviour has been investigated using an immersion test and electrochemical measurement. The biocompatibility was evaluated by cell growth factor using osteoblast-like SaOS2 cell. The experimental results indicate that the hot-rolled Mg–Zr–Ca alloys exhibit much finer microstructures than the as-cast Mg–Zr–Ca alloys which show coarse microstructures. The compressive strength of the hot-rolled alloys is much higher than that of the as-cast alloys and the human bone, which would offer appropriate mechanical properties for orthopaedic applications. The corrosion resistance of the alloys can be enhanced significantly by hot-rolling process. Hot-rolled Mg–0.5Zr–1Ca alloy (wt %) exhibits the lowest corrosion rate among all alloys studied in this paper. The hot-rolled Mg–0.5Zr–1Ca and Mg–1Zr–1Ca alloys exhibit better biocompatibility than other studied alloys and possess advanced mechanical properties, corrosion resistance and biocompatibility, suggesting that they have a great potential to be good candidates for orthopaedic applications.     

Effect of Al on the microstructure and mechanical properties of Mg–6Zn–2Sn–0.5Mn alloy

The microstructure and mechanical properties of Mg–6Zn–2Sn–0.5Mn–xAl (x?=?0, 1, 2, 3) alloy are investigated. The addition of Al leads to the refinement of grain size and the formation of Al₆Mn, Mg₃₂(Al,Zn)₄₉ also forms when the amount of Al is higher than 2?wt-%. Because of the addition of Al, the precipitates in the alloy after ageing treatment are refined. The alloy containing 1?wt-% Al shows good mechanical properties in the as-cast state which is attributed to the refined grains and low volume fraction of large second phases, it also shows high strength after ageing treatment resulted mainly from the homogeneously distributed fine precipitates, the yield strength, ultimate tensile strength and elongation are 183, 310?MPa and 11%, respectively.     

Microstructure and mechanical properties of Mg–6Li–xAl–0.8Sn alloys

As-cast and as-extruded Mg–6Li–xAl–0.8Sn (x?=?0, 1, 3 and 5?wt-%) alloys were prepared. The microstructure and mechanical properties were investigated and discussed. The experimental results show that the Mg–6Li–0.8Sn alloy is composed of three phases: α-Mg, Mg₂Sn and Li₂MgSn. With the addition of Al, the test alloys display typical α-Mg?+?β-Li duplex structures. The new Mg₁₇Al₁₂ and LiMgAl₂ phases were found in the Mg–6Li–1Al–0.8Sn alloy. The lamellar-type AlLi phase was formed whereas the Mg₁₇Al₁₂ phase disappeared in Mg–6Li–3Al–0.8Sn alloy. The LiMgAl₂ phase vanished in the Mg–6Li–5Al–0.8Sn alloy. The mechanical properties of as-extruded alloys were remarkably improved. The as-extruded Mg–6Li–3Al–0.8Sn alloy exhibited the best mechanical properties, with a yield strength, tensile strength and elongation of 209.8?MPa, 242.6?MPa and 15.5%, respectively.     

Microstructure and mechanical properties of twin-roll cast Mg–4.5Al–1.0Zn sheets processed by differential speed rolling

The microstructure and mechanical properties of the twin-roll cast (TRC) Mg–4.5Al–1.0Zn alloy sheets produced by differential speed rolling (DSR) were investigated by optical microscopy, transmission electron microscope and electron backscattered diffraction. The results are compared with those of the sheet processed by equal speed rolling (ESR). It is shown that twining played an important role at the initial stage of rolling. With the increase of the rolling reduction, the microstructures in the processed sheets become more homogeneous and they are more refined by DSR than by ESR. After annealing, the sheet processed by DSR shows a higher elongation and slightly lower yield strength than those of the ESR-processed sheet, which could be attributed to grain refinement and texture weakening. These results suggest that, in comparison with conventional casting and rolling, the combined technology of TRC and DSR is a more effective way to process magnesium sheets with enhanced formability after final annealing.     

Microstructure,mechanical properties and yield asymmetry of Mg–4Al–2Sn–xY alloys

The effect of 0, 0.3, 0.6, 0.9?wt-% Y addition on the microstructure and mechanical properties of extruded Mg–4Al–2Sn alloys were investigated. The results show that α-Mg, Mg₁₇Al₁₂, Mg₂Sn and Al₂Y phases form in the extruded Y-containing alloys. Mg₁₇Al₁₂ phase, containing trace amounts of Y, tends to distribute on the grain boundaries in the form of needles. When the Y content is 0.6?wt-%, the alloy has the best combination mechanical properties. Its tensile yield strength, ultimate tensile strength and tensile elongation are 172?MPa, 270?MPa and 11.2%, respectively. As the Y content increases, the tensile and compressive asymmetries in the Mg–4Al–2Sn–xY alloy decrease, due to grain refinement and the weakening of texture.     

Effects of the enhanced heat treatment on the mechanical properties and stress corrosion behavior of an Al–Zn–Mg alloy

In this article, the effects of the enhanced solution treatment (EST) and high-temperature pre-precipitation (HTPP) on the microstructures, mechanical properties, and stress corrosion cracking resistance of an Al–Zn–Mg alloy have been investigated. The results indicated that EST and HTPP can substantially affect the microstructures of the alloy. The width of the continuously distributed grain boundary precipitates decreases after the EST, while the continuous grain boundary precipitation changes to a discontinuous precipitation structure after both the EST and HTPP. The yield strength, tensile strength, elongation, and fracture toughness of the specimens after the EST are much higher than those of the specimens only after traditional solution treatment, since the EST substantially decreases the size and volume fraction of the constituents. The stress corrosion cracking resistance of the specimens after both the EST and HTPP has been greatly improved due to the discontinuous distribution, and high Cu and low Mg concentrations of the grain boundary precipitates.     

Effect of forging process on microstructure,mechanical and corrosion properties of biodegradable Mg–1Ca alloy

The performance of Mg–1Ca alloy, a biodegradable metallic material, may be improved by hot working in order that it may be of use in bone implant applications. In this study, Mg–1Ca cast alloy was preheated to different temperatures before undergoing forging process with various forging speeds. Macro- and microstructure of the samples were examined by stereo and scanning electron microscopes (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), respectively. To determine the mechanical properties of the alloy, hardness value and plastic deformation ability of the samples were measured. To investigate the corrosion behaviour of the alloy, immersion and electrochemical tests were performed on the samples in simulated body fluid and the corrosion products were characterized by SEM/EDS. The results showed that increasing forging temperature decreased grain size led to improved hardness value and plastic deformation ability of the alloy, whereas no significant effect was observed by changing forging speed. Moreover, forging at higher temperatures led to an increase in the amount of Mg₂Ca phase at grain boundaries resulted in higher corrosion rates. It can be concluded that although forging process improved the mechanical properties of the alloy, it does not satisfy the corrosion resistance criteria required for bone healing.     

Microstructure and mechanical properties of as aged Mg–3Sn–1Al and Mg–3Sn–2Zn–1Al alloy

Effect of Zn on the microstructure, age hardening response and mechanical properties of Mg–3Sn–1Al alloy which is immediately aged at 180°C after extrusion process (T5) was investigated. It was found that the Zn can refine the microstructure, remarkably improve the aging response with the peak hardness increases to 75 HV and the time to peak hardness reduces from ～110 to ～60 h, which is attributed to the solid solution hardening of Al, Zn and an amount of finer Mg₂Sn precipitates. The as aged Mg–3Sn–2Zn–1Al alloy exhibits better mechanical property at room temperature or 150°C than that of Mg–3Sn–1Al alloy, which is ascribed to the fine grained microstructure and thermally stable Mg₂Sn particles dispersed at grain boundaries and in the matrix.     

Effect of trace additions of Sn on microstructure and mechanical properties of Al–Cu–Mg alloys

The work is aimed at investigating the influence of trace additions of Tin (Sn) on the microstructure, mechanical properties and age-hardening behavior of Al–6.2%Cu–0.6%Mg alloy system. Al–6.2%Cu–0.6%Mg alloys containing varying weight percentages (from 0 to 0.1 wt.%) of Sn were prepared by casting technique. The mechanical properties and microstructure of these alloys were investigated in the as-cast as well as different heat treated conditions. The composition of the different phases present in the microstructure was determined by energy dispersive X-ray (EDS) analysis. The average grain size of the annealed alloy was found to be maximum with trace content of 0.06 wt.% Sn. The hardness and strength of the alloy increased but the ductility reduced with increase in Sn content up to 0.06 wt.%. Precipitation hardening behavior of the alloys was investigated by analyzing the aging time required to attain the peak hardness value. Addition of trace percentage of Sn was observed to have no significant influence on the peak ageing time of the investigated alloy system.     

Microstructure,mechanical and corrosion properties of Mg–Nd–Zn–Sr–Zr alloy as a biodegradable material

Abstract

The Mg–2·5Nd–0·3Zn–0·1Sr–0·4Zr (wt-%) alloy was prepared by gravity casting. Solution treatment and extrusion were conducted. The microstructure, mechanical properties, and corrosion behaviour of the alloy under as cast, T4-treated, and as extruded conditions were evaluated using scanning electron microscope, tensile test, microhardometre, immersion test, and electrochemical test. The results show that the as extruded alloy exhibits the highest ultimate tensile strength (231 MPa), elongation (36·6%), and microhardness (57·8 HV). The as cast alloy shows the best corrosion resistance because the relative continuously distributed eutectic phase with noble corrosion potential acts as a corrosion barrier. The as extruded Mg–Nd–Zn–Sr–Zr alloy with high ductility and good corrosion resistance is desirable for preparing biodegradable implants.     

Enhanced mechanical properties and corrosion behavior of Zn–30Sn–2Cu high-temperature lead-free solder alloy by adding Sm

Journal of Materials Science: Materials in Electronics - Zn–30Sn–2Cu–xSm (x?=?0, 0.1, 0.3, 0.5, and 1.0 wt%) solders were prepared to investigate its...     

Microstructure,mechanical properties and corrosion behaviour of Al–Si–Mg alloy matrix/zircon and alumina hybrid composite

In the present study, the effect of reinforcement on microstructure, mechanical properties and corrosion behaviour of aluminium–silicon–magnesium (Al–Si–Mg) alloy matrix hybrid composites reinforced with varying amounts of zircon and alumina has been investigated. Hardness and room temperature compressive tests were performed on Al–Si–Mg alloy as well as composites. Hardness and compressive strength was found to be higher for composites containing 3.75?% ZrSiO₄?+?11.25?% Al₂O₃. Similarly, Al–Si–Mg alloy and its composites were studied for corrosion behaviour in 1 N HCl corrosive media. The weight loss of all the composites was found to decrease with time due to the formation of passive oxide layer on the sample surface. The results obtained indicate that composites exhibit superior mechanical properties and corrosion resistance compared to unreinforced alloy.