Development of response surface model for tensile shear strength of weld-bonds of aluminium alloy 6061 T651

The development of a response surface model to study the influence of process parameters of weld-bonding on tensile shear strength of the weld-bond of 2 mm thick aluminium alloy 6061 T651 sheets has been reported. Significant and controllable process parameters of the weld-bonding (surface roughness, curing time, welding current, welding time and electrode pressure) and their ranges were identified by conducting pilot experiments. Welding current, welding time and welding pressure were identified as significant and controllable parameters. Influence of the significant process parameters and their interaction on the tensile shear strength of the weld-bonds was studied using response surface methodology (RSM). Using model, the optimal combination of weld bonding process parameters for maximum tensile shear strength of the weld bond was obtained. The validity of the model was evaluated on weld bonds developed using different levels of process parameters and testing their tensile shear strength. The model error was found to be in a range of 3–7%.     

Tensile behavior of friction stir welded AA 6061-T4 aluminum alloy joints

In this investigation response surface methodology based on a central composite rotatable design with three parameters, five levels and 20 runs, was used to develop a mathematical model predicting the tensile properties of friction stir welded AA 6061-T4 aluminum alloy joints at 95% confidence level. The three welding parameters considered were tool rotational speed, welding speed and axial force. Analysis of variance was applied to validate the predicted model. Microstructural characterization and fractography of joints were examined using optical and scanning electron microscopes. Also, the effects of the welding parameters on tensile properties of friction stir welded joints were analyzed in detail. The results showed that the optimum parameters to get a maximum of tensile strength were 920 rev/min, 78 mm/min and 7.2 kN, where the maximum of tensile elongation was obtained at 1300 rev/min, 60 mm/min and 8 kN.     

Effect of welding parameters on microstructure and mechanical properties of AA6061-T6 butt welded joints by stationary shoulder friction stir welding

Stationary shoulder friction stir welding (SSFSW) butt welded joints were fabricated successfully for AA6061-T6 sheets with 5.0 mm thickness. The welding experiments were performed using 750–1500 rpm tool rotation speeds and 100–300 mm/min welding speeds. The effects of welding parameters on microstructure and mechanical properties for the obtained welds were discussed and analyzed in detail. It is verified that the defect-free SSFSW welds with fine and smooth surface were obtained for all the selected welding parameters, and the weld transverse sections are obviously different from that of conventional FSW joint. The SSFSW nugget zone (NZ) has “bowl-like” shapes with fairly narrow thermal mechanically affected zone (TMAZ) and heat affected zone (HAZ) and the microstructures of weld region are rather symmetrical and homogeneous. The 750–1500 rpm rotation speeds apparently increase the widths of NZ, TMAZ and HAZ, while the influences of 100–300 mm/min welding speeds on their widths are weak. The softening regions with the average hardness equivalent 60% of the base metal are produced on both advancing side and retreating side. The tensile properties of AA6061-T6 SSFSW joints are almost unaffected by the 750–1500 rpm rotation speeds for given 100 mm/min, while the changing of welding speed from 100–300 mm/min for given 1500 rpm obviously increased the tensile strength of the joint and the maximum value for welding parameter 1500 rpm and 300 mm/min reached 77.3% of the base metal strength. The tensile fracture sites always locate in HAZ either on the advancing side or retreating side of the joints.     

Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of a super high strength Al–Zn–Mg–Cu aluminum alloy

Samples made of a super high strength aluminum alloy with high Zn content were friction stir welded with rotation rates of 350–950 rpm and welding speeds of 50–150 mm/min. The effect of welding parameters on the microstructure and mechanical properties was investigated. It was observed that the grain size of the nugget zones decreased with the increasing welding speed or the decreasing tool rotation rate. Most of the strengthening precipitates in the nugget zone were dissolved back and the intragranular and grain boundary precipitates in the heat affected zone coarsened significantly. The greatest ultimate tensile strength of 484 MPa and largest elongation of 9.4 were obtained at 350 rpm−100 mm/min and 350 rpm−50 mm/min, respectively. The ultimate tensile strength and elongation deteriorated drastically when rotation rate increased from 350 to 950 rpm at a constant welding speed of 100 mm/min.     

Effect of tool rotational speed and pin profile on microstructure and tensile strength of dissimilar friction stir welded AA5083-H111 and AA6351-T6 aluminum alloys

The relatively new welding process friction stir welding (FSW) was applied in this research work to join 6 mm thick dissimilar aluminum alloys AA5083-H111 and AA6351-T6. The effect of tool rotational speed and pin profile on the microstructure and tensile strength of the joints were studied. Dissimilar joints were made using three different tool rotational speeds of 600 rpm, 950 rpm and 1300 rpm and five different tool pin profiles of straight square (SS), straight hexagon (SH), straight octagon (SO), tapered square (TS), and tapered octagon (TO). Three different regions namely unmixed region, mechanically mixed region and mixed flow region were observed in the weld zone. The tool rotational speed and pin profile considerably influenced the microstructure and tensile strength of the joints. The joint which was fabricated using tool rotational speed of 950 rpm and straight square pin profile yielded highest tensile strength of 273 MPa. The two process parameters affected the joint strength due to variations in material flow behavior, loss of cold work in the HAZ of AA5083 side, dissolution and over aging of precipitates of AA6351 side and formation of macroscopic defects in the weld zone.     

Analysis of friction welding parameters on the mechanical metallurgical and chemical properties of AISI 1035 steel joints

In this present work, the analysis of process parameters on mechanical, metallurgical and chemical properties of American Iron and Steel Institute (AISI) 1035 steel rods of 12 mm diameter joints produced by friction welding is analyzed. The joints made with various process parameter combinations are subjected to tensile tests, hardness test and cyclic potentiodynamic polarization tests. The properties such as tensile strength, notch tensile strength, yield strength, % elongation, and vickers’s hardness, fully deformed zone (FDZ), flash formation and pitting corrosion has been analyzed for high level and low level process parameters. The optimized process variable is obtained by using Response Surface Methodology (RSM). The integrity of the welds has been investigated using high magnification optical microscopy. The fracture surface of the tensile test specimen is analyzed by using Scanning Electron Microscope (SEM) and Energy-dispersive X-ray spectroscopy (EDAX).     

Effect of welding parameters on microstructure and mechanical properties of friction stir spot welded 5052 aluminum alloy

Friction stir spot welding (FSSW) is a newly-developed solid state joining technology. In this study, two types of FSSW, normal FSSW and walking FSSW, are applied to join the 5052-H112 aluminum alloy sheets with 1 mm thickness and then the effect of the rotational speed and dwell time on microstructure and mechanical properties is discussed. The lower sheet material underneath the hook didn’t flow into the upper sheet due to the concave surface in the shoulder and groove in the anvil. The hardness profile of the welds exhibited a W-shaped appearance and the minimum hardness was measured in the HAZ. The results of tensile/shear tests and cross-tension tests indicate that the joint strength decreases with increasing rotational speed, while it’s not affected significantly by dwell time. At the rotational speed of 1541 rpm, the tensile/shear strength and cross-tension strength reached the maximum of 2847.7 N and 902.1 N corresponding to the dwell time of 5 s and 15 s. Two different fracture modes were observed under both tensile/shear and cross-tension loadings: shear fracture and tensile/shear mixed fracture under tensile/shear loadings, and nugget debonding and pull-out under cross-tension loadings. The performance of the welds plays a predominant role in determining the type of fracture modes. In addition, the adoption of walking FSSW brings unremarkable improvements in weld strength.     

Microstructure and mechanical properties of friction spot welded 6061-T4 aluminum alloy

Friction spot welding (FSpW) is a relatively new solid state joining technology developed by GKSS. In the present study, FSpW was applied to join the 6061-T4 aluminum alloy sheet with 2 mm thickness. The microstructure of the weld can be classified into four regions, which are stir zone (SZ), thermo-mechanically affected zone (TMAZ), heat affected zone (HAZ) and the base material (BM), respectively. Meanwhile, defects such as bonding ligament, hook and voids are found in the weld, which are associated to the material flow. The hardness profile of the weld exhibits a W-shaped appearance and the minimum hardness is measured at the boundary of TMAZ and SZ. Both the tensile/shear strength and cross-tension strength reach the maximum of 7117.0 N and 4555.4 N at the welding condition of the rotational speed of 1500 rpm and duration time of 4 s. Compared to cross-tension strength, the tensile/shear strength were stable with the variation of processing parameters. Three different fracture modes are observed under tensile/shear loading, which are plug type fracture, shear fracture and plug-shear fracture. There are also there different fracture modes under cross-tension loading, which are plug type fracture (on the upper sheet), nugget debonding and plug type fracture (on the lower sheet).     

Microstructure and mechanical properties of friction stir welded 6082 AA in as welded and post weld heat treated conditions

Friction stir welding of 6082 AA-T651 was performed using three different combinations of feed rates (90, 140 and 224 mm/min) and tool rotational speeds (850, 1070 and 1350 rpm). Mechanical properties of the weldments were evaluated by hardness measurements on the transverse section and tensile testing, while microstructure evaluation was done by optical microscopy and electron back scattered diffraction (EBSD). Irrespective to welding parameters the dynamically recrystallized grains in the stir zone were measured to be in the range of 2–3 μm for different feeds rates and rotational speeds. A considerable loss in hardness in the stir zone and more severely in the thermo-mechanically affected zone was noted due to dissolution of β′ and β″ second phase particles. A post weld heat treatment (PWHT) of 175 °C for 5 and 12 h was given to the weldments for all welding conditions and the mechanical properties and microstructure were re-evaluated. The hardness and strength were partially recovered and this was attributed to the possible re-precipitation of the β″ precipitates. The grain size barely exhibited a change, whereas the texture displayed a significant diminish in the Goss orientation after PWHT.     

The optimisation of process parameters for friction stir spot-welded AA3003-H12 aluminium alloy using a Taguchi orthogonal array

The aim of the present work is to optimise the welding parameters for friction stir spot welded non-heat-treatable AA3003-H12 aluminium alloy sheets using a Taguchi orthogonal array. The welding parameters, such as the tool rotational speed, tool plunge depth and dwell time, were determined according to the Taguchi orthogonal table L9 using a randomised approach. The optimum welding parameters for the peak tensile shear load of the joints were predicted, and the individual importance of each parameter on the tensile shear load of the friction stir spot weld was evaluated by examining the signal-to-noise ratio and analysis of variance (ANOVA) results. The optimum levels of the plunge depth, dwell time and tool rotational speed were found to be 4.8 mm, 2 s and 1500 rpm, respectively. The ANOVA results indicated that the tool plunge depth has the higher statistical effect with 69.26% on the tensile shear load, followed by the dwell time and rotational speed. The tensile shear load of the friction stir spot welding (FSSW) joints increased with increasing plunge depth. Additionally, examination of the weld cross-sections, microhardness tests and fracture characterisation of the selected friction spot welded joints were conducted to understand the better performance of the joints. All the fractures of the joints during tensile testing occurred at stir zone (SZ), where the bonded section was minimum. The tensile shear load and tensile deformation of the FSSW joints increased linearly with increasing the bonded size. The finer grain size in the SZ led to the higher hardness, which resulted in higher fracture strength. When the tensile shear load of the joints increased approximately 3-fold, the failure energy absorption of the joints increased approximately 15-fold.     

Effects of tool rotation speed on microstructures and mechanical properties of AA2219-T6 welded by the external non-rotational shoulder assisted friction stir welding

The external non-rotational shoulder assisted friction stir welding (NRSA-FSW) was applied to weld high strength aluminum alloy 2219-T6 successfully, and effects of the tool rotation speed on microstructures and mechanical properties were investigated in detail. Defect-free joints were obtained in a wide range of tool rotation speeds from 600 rpm to 900 rpm, but cavity defects appeared on the advancing side when the tool rotation speed increased to 1000 rpm. The microstructural deformation and heat generation were dominated by the rotating tool pin and sub-size concave shoulder, while the non-rotational shoulder helped to improve the weld formation. Microstructures and Vickers hardness distributions showed that the NRSA-FSW is beneficial to improving the asymmetry and inhomogeneity, especially in the weld nugget zone (WNZ). At the tool rotation speed of 800 rpm, both the tensile strength and the elongation reached the maximum, and the maximum tensile strength was up to 69.0% of the base material. All defect-free joints were fractured at the weakest region with minimum Vickers hardness in the WNZ, while for the joint with cavity defects the fracture occurred at the defect location.     

Laser,tungsten inert gas,and metal active gas welding of DP780 steel: Comparison of hardness,tensile properties and fatigue resistance

The microstructural characteristics, tensile properties and low-cycle fatigue properties of a dual-phase steel (DP780) were investigated following its joining by three methods: laser welding, tungsten inert gas (TIG) welding, and metal active gas (MAG) welding. Through this, it was found that the size of the welded zone increases with greater heat input (MAG > TIG > laser), whereas the hardness of the weld metal (WM) and heat-affected zone (HAZ) increases with cooling rate (laser > TIG > MAG). Consequently, laser- and TIG-welded steels exhibit higher yield strength than the base metal due to a substantially harder WM. In contrast, the strength of MAG-welded steel is reduced by a broad and soft WM and HAZ. The fatigue life of laser-and TIG-welded steel was similar, with both being greater than that of MAG-welded steel; however, the fatigue resistance of all welds was inferior to that of the non-welded base metal. Finally, crack initiation sites were found to differ depending on the microstructural characteristics of the welded zone, as well as the tensile and cyclic loading.     

Defect features and mechanical properties of friction stir lap welded dissimilar AA2024–AA7075 aluminum alloy sheets

5 mm-Thick dissimilar AA2024-T3 and AA7075-T6 aluminum alloy sheets were friction stir lap welded in two joint combinations, i.e., (top) 2024/7075 (bottom) and 7075/2024. The influences of process conditions (welding speed and joint combination) on defects (hook and voids) features and mechanical properties of joints were investigated in detail. It was found that the hook deflects largely upwards into the stir zone (SZ) at lower welding speeds (50, 150 mm/min) in both combinations. The process conditions significantly affect the hook geometry which in return affects the lap shear strength. In all 2024/7075 joints, voids appear and the joints fracture from the tip of hook on AS along the SZ/TMAZ (thermomechanically affected zone) interface in lap shear test (tensile fracture mode). In 7075/2024 joints, the hook on RS horizontally extends a large distance into the bottom stir zone at higher welding speeds (225, 300 mm/min). The joints fracture in three modes: shear fracture along the lap interfaces, tensile fracture and the mix fracture of both. In both joint combinations, the lap shear strength generally increases with the increase of welding speed. 7075/2024 Joints show higher failure load than 2024/7075 joints at lower welding speeds while the opposite result appears at higher welding speeds.     

Investigation of laser welding on butt joints of Al/steel dissimilar materials

Dissimilar metals of AA6013 aluminum alloy and Q235 low-carbon steel of 2.5 mm thickness were butt joined using a 10 kW fiber laser welding system with ER4043 filler metal. The study indicates that it is feasible to join aluminum alloy to steel by butt joints when zinc layer was hot-dip galvanized at the steel’s groove face in advance, and better weld appearance can be obtained at appropriate welding parameters. The joints had dual characteristics of a welding joint on the aluminum side and a brazing joint on the steel side. The smooth Fe₂Al₅ layer adjacent to the steel matrix and the serrated-shape FeAl₃ layer close to the weld metal were formed at the brazing interface. The overall thickness of Fe–Al intermetallic compounds layers produced in this experiment were varied from 1.8 μm to 6.2 μm at various welding parameters with laser power of 2.85–3.05 kW and wire feed speed of 5–7 m/min. The Al/steel butt joints were failed at the brazing interface during the tensile test and reached the maximum tensile strength of 120 MPa.     

Microstructure and tensile strength of friction stir welded joints between interstitial free steel and commercially pure aluminium

In the present study, the joining of interstitial free steel and commercial pure aluminium was carried out by friction stir welding (FSW) technique using tool rotational speeds of 600, 900, 1200 rpm and traverse speed of 100 mm/min. The microstructure and micro-hardness of the weld interface have been investigated. Optical microscopy was used to characterize the microstructures of different regions of friction stir welding joints. The scanning electron microscopy-back scattered electron (SEM-BSE) images show the existence of the different reaction layers in the welded zone. The Al₃Fe intermetallic compound has been observed in the weld interface and their thickness increase with the increase in tool rotational speed. Tensile strength was also evaluated and maximum tensile strength of ∼123.2 MPa along with ∼4.5% elongation at fracture of the joint have been obtained when processed at 600 rpm tool rotational speed.     

Friction stir welded T-joints optimization

The increasing use of aluminium alloys in transportation industry, such as railways, shipbuilding and aeronautics, promotes the development of more efficient and reliable welding processes. Friction stir welding (FSW) is a prominent solid-state joining technology that arose as a possible reliable welding solution. Optimized process parameters are not regularly used in previous studies found in the literature, in particular T-joints, which difficult the process industrial application. This study is focused on the optimization of friction stir welded T-joints using the Taguchi method. Mechanical tests of 27 different welded joints were carried out, and results were analysed using ANOVA, mean effect and response surface methodology (RSM). The tool rotational speed was verified to be the most influent factor in the joint mechanical properties, and is strongly dependent on the shoulder/probe diameters ratio. It was also shown that using 1000 rpm, 3.90 mm of probe depth and shoulder/probe diameters ratio of 2.5 (shoulder diameter of 15 mm) it may be achieved improved joint strength. For the optimized parameters it was verified that the welding speed does not have a significant influence. Equations to predict the joints mechanical properties were also derived through multiple regression.     

Experimental investigations on welding behaviour of sintered and forged Fe–0.3%C–3%Mo low alloy steel

Tungsten Inert Gas (TIG) welding is considered as one of the cleanest welding methods. It is generally adopted for thinner materials with moderate weld joint strengths. Welding of sintered porous materials continues to be a challenge due to the inherent porosity of the parent metals. The present research work attempts to address some of the issues relating to the welding behaviour of sintered and forged Fe–0.3%C–3%Mo low alloy steels under TIG welding. Rectangular strips of size 70 mm × 15 mm × 5 mm, obtained by blending, compacting and sintering of elemental powders of iron, graphite and molybdenum, were upset forged – both hot and cold in order to obtain alloy steel strips of various porosities. Two identical alloy steel strips of equal density were then welded both along longitudinal and transverse directions, by TIG welding, employing filler metal of suitable composition. The welded strips were then subjected to tensile test, hardness test, microstructural and Scanning Electron Microscope (SEM) fractography studies. Cold/hot upsetting of the sintered alloy preforms has led to enhanced density. As a result of improved density, their tensile strength and hardness values were also found to be enhanced. The welded alloy exhibited higher tensile strength compared to the un-welded base metal, due to strengthening by residual stress. Similarly, the strength and hardness of the welded alloy strips were found to be enhanced with increase in density. The tensile strength of welded joint is found to be higher compared to that of the base metal due to alloy metals segregation, rapid cooling and formation of acicular ferrite at the weldment of welded joint. No porosity was observed in the weld metal or Heat Affected Zone (HAZ) of the weld joint. However, the base metal had numerous micro pores, though pore migration towards weldment has not been observed.     

Microstructure and mechanical properties of thixoformed A319 aluminium alloy

Thixoforming is a viable technology for forming alloys in a semisolid state into near net-shaped products. In the present study, the effect of a thixoforming process on the microstructure and mechanical properties of A319 aluminium alloy was investigated. The ingots obtained from the cooling slope were thixoformed in a press after they remained at 571 °C for 5 min, yielding a microstructure predominantly composed of α-Al globules and inter-globular Si particles. Some of the thixoformed samples were treated with an ageing process (T6) and then, hardness and tensile samples were prepared from the as-cast, as-thixoformed and thixoformed T6. All the thixoformed samples were characterised using optical microscopy, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and X-ray diffraction (XRD) as well as hardness measurements and tensile tests. The results indicate that the mechanical properties of the thixoformed A319 alloy increased after the T6 heat treatment (hardness of 124.2 ± 3.2 HV, tensile strength of 298 ± 3.0 MPa, yield strength of 201 ± 2.6 MPa and elongation to fracture of 4.5 ± 0.3%). The fracture samples from the tensile test were analysed, revealing that the iron-rich intermetallic observed in the samples reduced the tensile strength and ductility of the thixoformed A319 alloys.     

Microstructural evolution and mechanical properties of dissimilar Al–Cu joints produced by friction stir welding

5A02 aluminum alloy and pure copper were joined by friction stir welding (FSW). A defect-free joint was obtained when one of process parameters, i.e. the traverse speed was lowered from 40 mm/min to 20 mm/min. A good mixing of Al and Cu was observed in the weld nugget zone (WNZ). A large amount of fine Cu particles were dispersed in the upper part of the WNZ producing a composite-like structure. In the lower part, nano-scaled intercalations were observed and identified by transmission electron microscopy (TEM). These layered structures were subsequently confirmed as Al₄Cu₉ (γ), Al₂Cu₃ (ε), Al₂Cu (θ), respectively. Formation of these microstructures caused an inhomogeneous hardness profile. Particularly, a distinct rise in hardness was noticed at the Al/Cu interface. Excellent metallurgical bonding between Al and Cu gave rise to good behaviors in the tensile and bending strength.     

Fatigue in laser welded titanium tubes intended for use in aircraft pneumatic systems

The pneumatic system conducts the pressurized hot air from the engine to the environmental systems of the aircrafts. In-service failures of arc-welded pneumatic parts have driven further developments of laser beam welding as an alternative method. Here, a fiber laser with 2 kW power had been employed to weld commercial purity titanium tubes with 0.5 mm wall thickness and 50 mm diameter. For comparison purposes, semiautomatic TIG welding was realized. The chosen parameters speed and laser power for laser welding were 200 W–2 m/min and 250 W–3 m/min. The laser welded tubes presented 1 mm wide weld beads composed by partially twinned α-Ti grains. The TIG welded tubes showed 5 mm wide beads composed by acicular α-grains. These observed differences had been associated with the cooling rates, which are ten times higher in the laser case. Both laser and TIG welded tubes were cycled 44,000 times in a pneumatic bench at 350 °C without failures or cracks that could release the internal pressure. After the pressurization tests, the tubes were tested for tensile and fatigue resistance. The yield stresses, tensile strengths and total elongation did not change comparing base material, TIG welded and laser welded cases. The condition 200 W–2 m/min presented superior fatigue resistance values compared to other welding conditions, and could be considered similar to the tubes in the unwelded condition. The microstructural and mechanical results had shown that the current laser technology can replace, with advantages, the arc welding for the joining of the titanium tubes.