Correlation between precipitate microstructure and mechanical properties in AA7075‐T6 aluminum alloy friction stir welded joints

Microstructural evolution and mechanical properties of friction stir welded AA7075‐T6 aluminum alloy were examined. Grain structure and precipitate evolution in the stir zone and heat‐affected zone were evaluated using optical microscope and differential scanning calorimetry. A significant grain refinement and dissolution of η′ precipitates in the stir zone were found, but chromium‐bearing dispersoids remained nearly unchanged. The main particles in the stir zone and heat‐affected zone were η precipitates as well as Guinier‐Preston zones formed during post‐weld natural aging. The small recrystallized grains were observed in the thermo‐mechanically affected zone next to the stir zone. A W‐shaped hardness distribution where soft region was produced in the heat‐affected zone at a short distance from the stir zone were obtained. Hardness profiles of the welds were explained by precipitate distributions. Friction stir welding resulted in the reversion and coarsening of η′ precipitates. The formation of Guinier‐Preston zones in the stir zone and some parts of the heat‐affected zone during post‐weld natural aging increased the hardness. In transverse tensile specimens, fracture occurred in a location with the minimum hardness at either advancing or retreating side randomly. Further, influences of welding parameters on mechanical properties were investigated.     

Effect of welding parameters on microstructure and mechanical properties of AA6061-T6 butt welded joints by stationary shoulder friction stir welding

Stationary shoulder friction stir welding (SSFSW) butt welded joints were fabricated successfully for AA6061-T6 sheets with 5.0 mm thickness. The welding experiments were performed using 750–1500 rpm tool rotation speeds and 100–300 mm/min welding speeds. The effects of welding parameters on microstructure and mechanical properties for the obtained welds were discussed and analyzed in detail. It is verified that the defect-free SSFSW welds with fine and smooth surface were obtained for all the selected welding parameters, and the weld transverse sections are obviously different from that of conventional FSW joint. The SSFSW nugget zone (NZ) has “bowl-like” shapes with fairly narrow thermal mechanically affected zone (TMAZ) and heat affected zone (HAZ) and the microstructures of weld region are rather symmetrical and homogeneous. The 750–1500 rpm rotation speeds apparently increase the widths of NZ, TMAZ and HAZ, while the influences of 100–300 mm/min welding speeds on their widths are weak. The softening regions with the average hardness equivalent 60% of the base metal are produced on both advancing side and retreating side. The tensile properties of AA6061-T6 SSFSW joints are almost unaffected by the 750–1500 rpm rotation speeds for given 100 mm/min, while the changing of welding speed from 100–300 mm/min for given 1500 rpm obviously increased the tensile strength of the joint and the maximum value for welding parameter 1500 rpm and 300 mm/min reached 77.3% of the base metal strength. The tensile fracture sites always locate in HAZ either on the advancing side or retreating side of the joints.     

Effect of post-weld natural aging on mechanical and microstructural properties of friction stir welded 6063-T4 aluminium alloy

Influence of natural aging on mechanical and microstructural properties of friction stir welded 6063-T4 aluminium alloy plates was investigated through mechanical testing, X-ray diffraction studies, and transmission electron microscopy, for aging times up to 8640 h. Mg–Si co-clusters formed during the natural aging process resulted in an increase in strength, decrease in ductility, and occurrence of serrated plastic flow. Hardness increase from aging was fastest in welds obtained at higher tool rotational speeds due to greater amount of “quenched-in” vacancies from higher peak stir zone temperatures. Peak broadening analyses and classical Williamson–Hall plots were used to investigate the effect of friction stir welding and post weld natural aging on microstrain in different weld regions. Higher microstrain was found in stir zone as well as heat affected zone as compared to that for base metal, albeit for different reasons.     

Microstructure feature of friction stir butt-welded ferritic ductile iron

This study conducted friction stir welding (FSW) by using the butt welding process to join ferritic ductile iron plates and investigated the variations of microsturcture in the joined region formed after welding. No defects appeared in the resulting experimental weld, which was formed using a 3-mm thick ductile iron plate and tungsten carbide alloy stir rod to conduct FSW at a rotational speed of 982 rpm and traveling speed of 72 mm/min. The welding region was composed of deformed graphite, martensite phase, and dynamically recrystallized ferrite structures. In the surface region and on the advancing side (AS), the graphite displayed a striped configuration and the ferritic matrix transformed into martensite. On the retreating side (RS), the graphite surrounded by martensite remained as individual granules and the matrix primarily comprised dynamically recrystallized ferrite. After welding, diffusion increased the carbon content of the austenite around the deformed graphite nodules, which transformed into martensite during the subsequent cooling process. A micro Vickers hardness test showed that the maximum hardness value of the martensite structures in the weld was approximately 800 HV. An analysis using an electron probe X-ray microanalyzer (EPMA) indicated that its carbon content was approximately 0.7–1.4%. The peak temperature on the RS, 8 mm from the center of the weld, measured 630 °C by the thermocouple. Overall, increased severity of plastic deformation and process temperature near the upper stir zone (SZ) resulted in distinct phase transformation. Furthermore, the degree of plastic deformation on the AS was significantly greater than that on the RS, and relatively complete graphite granules and the fine ferrite grains resulting from dynamic recrystallization were observed on the RS.     

Influence of welding parameters and tool pin profile on microstructure and mechanical properties along the thickness in a friction stir welded aluminum alloy

Microstructure, second-phase particles and mechanical properties of the joint along the thickness of plate during friction stir welded 2219 aluminum alloy thick plate using different shapes pin were investigated in this paper. The top presented larger equiaxed recrystallized grain structure and finer second-phase particles compared to the middle and bottom. Thermo-mechanically affected zone and boundary were more optically distinct on the advancing side in comparison with the retreating side. Grain size and particles were much finer and dispersed using the first tool with three spiral flute or at the lower rotational speed of 300 rpm. The strength and ductility in top slices was slightly higher than that in middle and bottom, increased with increasing traverse speed from 60 to 100 mm/min or the decrease of rotational speed from 500 to 300 rpm using the first tool. The mechanical properties using the second tool was lower than that of first tool, which was consistent with the hardness curves.     

Evaluation of microstructures and mechanical properties of friction stir welded lap joints of Inconel 600/SS 400

The microstructures and mechanical properties of friction stir welded Inconel 600 and SS 400 lap joints were evaluated in this study. Friction stir welding was carried out at a tool rotation speed of 200 rpm and a welding speed of 100 mm/min. Application of friction stir welding was notably effective in reducing the grain size of the stir zone, as a result, the average grain size of Inconel 600 was reduced from 20 μm in the base material to 8.5 μm in the stir zone. The joint interface between Inconel 600 and SS 400 was soundly welded without voids and cracks, and MC carbides with a size of 50 nm were partially formed in the region of the lap joint interface in Inconel 600. In addition, a hook from SS 400 was formed on the advancing side of the Inconel 600 alloy, which directly affected an increase in the peel strength of the weld. In this study, we systematically discussed the effect of friction stir welding on the evolution of the microstructures and mechanical properties of friction stir lap jointed Inconel 600 and SS 400.     

The investigation of abnormal particle-coarsening phenomena in friction stir repair weld of 2219-T6 aluminum alloy

The single-pass friction stir weld of aluminum 2219-T6 with weld-defects was repaired by overlapping friction stir welding technique. However, without any post weld heat treatment process, it was found that the phenomena of abnormal particle-coarsening of Al₂Cu had occurred in the overlapping friction stir repair welds. The detecting results of non-destructive X-ray inspection proved that not only one group of repair FSW process parameters could lead to occurrence of the abnormal phenomena. And the abnormally coarsened particles always appeared on the advancing side of repair welds rather than the retreating side where the fracture behaviors occurred after mechanical tensile testing. The size of the biggest particle lying in the dark bands of ‘Onion-rings’ was more than 150 μm. After the related investigation by scanning electron microscope and X-ray energy spectrometer, three types of formation mechanisms were proposed for reasonably explaining the abnormal phenomenon: Aggregation Mechanism, Diffusion Mechanisms I and II. Aggregation Mechanism was according to the motion-laws of stir-pin. Diffusion Mechanisms were based on the classical theories of precipitate growth in metallic systems. The combined action of the three detailed mechanisms contributed to the abnormal coarsening behavior of Al₂Cu particles in the friction stir repair weld.     

Effects of tool rotation speed on microstructures and mechanical properties of AA2219-T6 welded by the external non-rotational shoulder assisted friction stir welding

The external non-rotational shoulder assisted friction stir welding (NRSA-FSW) was applied to weld high strength aluminum alloy 2219-T6 successfully, and effects of the tool rotation speed on microstructures and mechanical properties were investigated in detail. Defect-free joints were obtained in a wide range of tool rotation speeds from 600 rpm to 900 rpm, but cavity defects appeared on the advancing side when the tool rotation speed increased to 1000 rpm. The microstructural deformation and heat generation were dominated by the rotating tool pin and sub-size concave shoulder, while the non-rotational shoulder helped to improve the weld formation. Microstructures and Vickers hardness distributions showed that the NRSA-FSW is beneficial to improving the asymmetry and inhomogeneity, especially in the weld nugget zone (WNZ). At the tool rotation speed of 800 rpm, both the tensile strength and the elongation reached the maximum, and the maximum tensile strength was up to 69.0% of the base material. All defect-free joints were fractured at the weakest region with minimum Vickers hardness in the WNZ, while for the joint with cavity defects the fracture occurred at the defect location.     

Effect of tool rotational speed and pin profile on microstructure and tensile strength of dissimilar friction stir welded AA5083-H111 and AA6351-T6 aluminum alloys

The relatively new welding process friction stir welding (FSW) was applied in this research work to join 6 mm thick dissimilar aluminum alloys AA5083-H111 and AA6351-T6. The effect of tool rotational speed and pin profile on the microstructure and tensile strength of the joints were studied. Dissimilar joints were made using three different tool rotational speeds of 600 rpm, 950 rpm and 1300 rpm and five different tool pin profiles of straight square (SS), straight hexagon (SH), straight octagon (SO), tapered square (TS), and tapered octagon (TO). Three different regions namely unmixed region, mechanically mixed region and mixed flow region were observed in the weld zone. The tool rotational speed and pin profile considerably influenced the microstructure and tensile strength of the joints. The joint which was fabricated using tool rotational speed of 950 rpm and straight square pin profile yielded highest tensile strength of 273 MPa. The two process parameters affected the joint strength due to variations in material flow behavior, loss of cold work in the HAZ of AA5083 side, dissolution and over aging of precipitates of AA6351 side and formation of macroscopic defects in the weld zone.     

Characteristics of the reverse dual-rotation friction stir welding conducted on 2219-T6 aluminum alloy

Reverse dual-rotation friction stir welding (RDR-FSW) has great potential to obtain appropriate welding conditions through adjusting the independently rotating tool pin and surrounding shoulder. The welding torque exerted on the workpiece by the reversely rotating shoulder also cancels off a part of the welding torque exerted by the rotating tool pin, thus the clamping requirement for the workpiece is also reduced. In the present paper, a tool system for the RDR-FSW was designed and successfully applied to weld high strength aluminum alloy 2219-T6, and then microstructures and mechanical properties of the optimized joint were investigated to demonstrate the RDR-FSW characteristics. The weld nugget zone was characterized by the homogeneity of refined grain structures, but there was a three-phase confluction on the advancing side formed by different grain structures from three different zones. The tensile strength of the optimized joint was 328 MPa (73.7% of the base material), showing an obvious improvement when compared with the optimized joint welded by the FSW without the reversely rotating assisted shoulder. The tensile fracture occurred in the ductile fracture mode and the fracture path propagated in the weakest region where the Vickers hardness is the minimum.     

AA7075 bit for repairing AA2219 keyhole by filling friction stir welding

In the present study, 7.8 mm thick AA2219 rolled plates were successfully filling friction stir welded (FFSW) without keyhole using a semi-consumable tool. The influences of the bit’s geometric parameters and the plunge speed on the joint’s mechanical properties were investigated. Microstructure of the joint, especially at the interface, was observed. The results revealed that the AA7075 bit’s employment was able to decrease the shedding bit material effectively. During tensile tests, the maximum ultimate tensile strength (UTS) and elongation of the joint were 179.6 MPa and 13.7%, equivalent to 96.6% and 99% of the original defect-free friction stir welding (FSW) joint, respectively. The defect-free FFSW joints were produced at lower plunge speeds, and the fracture locations were at the softened region within the heat affected zone (HAZ) adjacent to the thermo-mechanically affected zone (TMAZ) on the retreating side. With increasing the plunge speed, the fracture location was more mainly dependent on the interface strength instead of the hardness distribution.     

人工时效对7003/7046铝合金搅拌摩擦焊接头组织和力学性能的影响

采用差示扫描量热分析、硬度、室温拉伸实验、背散射电子衍射和透射电子显微镜等手段研究了焊后人工时效对7003-7046异种铝合金搅拌摩擦焊接(FSW)接头的微观组织和力学性能的影响。结果表明：FSW接头后退侧(7046铝合金侧)的硬度明显高于前进侧(7003铝合金侧),两侧平均硬度的差约为30HV;人工时效后接头的硬度提高,两侧平均硬度的差增大到约50HV,接头的屈服强度提高,抗拉强度略有提高,伸长率几乎不变。根据时效前后FSW接头不同区域微观组织的特征,分析了接头力学性能变化的原因。     

Microstructure and mechanical properties of friction stir welded 7136–T76 aluminium alloy

Abstract

The microstructure of the weld was examined by light and electron microscopy (scanning and transmission). The various regions, i.e. thermomechanically affected zone, heat affected zone and unaffected base material, were studied in detail to better understand the microstructural evolution during friction stir welding and its impact on basic mechanical properties. The change in morphology of the strengthening phases reflected the relative temperature profile and the amount of deformation across the welded joint during the stir welding process. The centre of the weld was composed of fine grains and coarse particles identified mainly as MgZn₂. In the thermomechanically and heat affected zones, the grain size was not uniform, and the strengthening phases filled the grain interiors, while grain boundaries were surrounded by precipitation free zones. The size of the strengthening phase decreased towards the base material. The hardness profile of the friction stir weld displayed the lowest hardness on the retreating side. Tensile properties of the weld itself were superior to those for material containing weld.     

EBSD study on microstructure and texture of friction stir welded AA5052-O and AA6061-T6 dissimilar joint

Friction stir welded AA5052-O and AA6061-T6 dissimilar joint has a more obvious impact on microstructure and texture evolution compared to single material welding due to differences in physical and chemical parameters between two aluminum alloys. Microstructure, texture evolution and grain structure of AA5052-O and AA6061-T6 dissimilar joint were investigated by means of OM,EBSD and TEM measurements. Experimental results showed that FS weld was generalized in four regions–nugget zone (NZ),thermomechanically affected zone (TMAZ),heat affected zone (HAZ) and base metals (BM), using standard nomenclatures. NZ exhibited the complex structure of the two materials with flowing shape and mainly composed of the advancing side material Subgrain boundaries in weld nugget zone gradually transformed into high angle grain boundaries by absorbing dislocation and accumulating misorientations. Grain refinement of weld nugget zone was achieved by dynamic recrystallization. In the friction stir welding process, the presence of the shear deformation in weld made {001} < 100 > C cube texture, {123} < 634 > S texture in BM gradually transformed into {111} < 1(−)12(−) > A1¹ shear texture. HABs distribution were most significant in nugget followed by RS and then by AS. In TMAZ and NZ, numerous precipitates and lots of dislocations were observed.     

The optimisation of process parameters for friction stir spot-welded AA3003-H12 aluminium alloy using a Taguchi orthogonal array

The aim of the present work is to optimise the welding parameters for friction stir spot welded non-heat-treatable AA3003-H12 aluminium alloy sheets using a Taguchi orthogonal array. The welding parameters, such as the tool rotational speed, tool plunge depth and dwell time, were determined according to the Taguchi orthogonal table L9 using a randomised approach. The optimum welding parameters for the peak tensile shear load of the joints were predicted, and the individual importance of each parameter on the tensile shear load of the friction stir spot weld was evaluated by examining the signal-to-noise ratio and analysis of variance (ANOVA) results. The optimum levels of the plunge depth, dwell time and tool rotational speed were found to be 4.8 mm, 2 s and 1500 rpm, respectively. The ANOVA results indicated that the tool plunge depth has the higher statistical effect with 69.26% on the tensile shear load, followed by the dwell time and rotational speed. The tensile shear load of the friction stir spot welding (FSSW) joints increased with increasing plunge depth. Additionally, examination of the weld cross-sections, microhardness tests and fracture characterisation of the selected friction spot welded joints were conducted to understand the better performance of the joints. All the fractures of the joints during tensile testing occurred at stir zone (SZ), where the bonded section was minimum. The tensile shear load and tensile deformation of the FSSW joints increased linearly with increasing the bonded size. The finer grain size in the SZ led to the higher hardness, which resulted in higher fracture strength. When the tensile shear load of the joints increased approximately 3-fold, the failure energy absorption of the joints increased approximately 15-fold.     

Effect of heat treatment on tensile properties of friction stir welded joints of 2219-T6 aluminium alloy

Abstract

The effect of post-weld heat treatment (PWHT) on the tensile properties of friction stir welded (FSW) joints of 2219-T6 aluminium alloy was investigated. The PWHT was carried out at aging temperature of 165°C for 18 h. The mechanical properties of the joints were evaluated using tensile tests. The experimental results indicate that the PWHT significantly influences the tensile properties of the FSW joints. After the heat treatment, the tensile strength of the joints increases and the elongation at fracture of the joints decreases. The maximum tensile strength of the joints is equivalent to 89% of that of the base material. The fracture location characteristics of the heat treated joints are similar to those of the as welded joints. The defect free joints fracture in the heat affected zone on the retreating side and the joints with a void defect fracture in the weld zone on the advancing side. All of the experimental results can be explained by the hardness profiles and welding defects in the joints.     

Process parameters/material location affecting hooking in friction stir lap welding: Dissimilar aluminum alloys

Influence of spindle and weld speeds, metal location, direction of spindle rotation, and tool pin length on hooking in lap FSW of dissimilar aluminum alloys and the effect of hook on tensile and fatigue weld strength was studied. Optical images of the cross-section of the specimen welded at different process parameters were analyzed. The results indicate that increased spindle speed, reduced weld speed, higher tool pin length, clockwise spindle rotation, and locating the stronger material at the bottom of the joint increased the size of the hooking defect. Higher weld speeds and very high spindle speeds resulted in lower hook size on the advancing side (AS) compared to the retreating side (RS) of the joint. Welding with low weld speed would result in higher advancing side hook size compared to the retreating side. Friction stir weld joints fabricated with anti-clockwise spindle rotation has been found to have extremely low hook both on the AS and the RS of the joint. The tensile and fatigue strengths of the weld joints and plates are degraded by the hook. The fatigue strength of welded alloys could be improved by a double pass weld, the second pass welded immediately adjacent to the first pass.     

搅拌摩擦焊焊缝横截面塑性材料迁移行为分析

在搅拌摩擦焊过程中,焊缝塑性材料的迁移是保证焊缝的冶金完整性的重要因素.本研究通过采用镶嵌标示材料的方法,焊后观察焊缝横截面上塑性材料的迁移行为.研究结果表明:在焊缝横截面上,探针附近的塑性材料沿带左旋螺纹的探针表面从焊缝上表面螺旋迁移至焊缝底部,从四周向焊缝表面迁移,在厚度方向上形成一个连续迁移的循环路径.塑性变形的区域关于焊缝中心不对称,塑性材料在焊缝中心形成类似于倾斜"花瓶"状的形貌.从焊缝表面至底面,塑性变形区宽度逐渐减小,前进边塑性材料向焊缝表面迁移的距离小于返回边,前进边塑性变形区小于返回边.     

Microstructure and mechanical properties of friction stir welded 6082 AA in as welded and post weld heat treated conditions

Friction stir welding of 6082 AA-T651 was performed using three different combinations of feed rates (90, 140 and 224 mm/min) and tool rotational speeds (850, 1070 and 1350 rpm). Mechanical properties of the weldments were evaluated by hardness measurements on the transverse section and tensile testing, while microstructure evaluation was done by optical microscopy and electron back scattered diffraction (EBSD). Irrespective to welding parameters the dynamically recrystallized grains in the stir zone were measured to be in the range of 2–3 μm for different feeds rates and rotational speeds. A considerable loss in hardness in the stir zone and more severely in the thermo-mechanically affected zone was noted due to dissolution of β′ and β″ second phase particles. A post weld heat treatment (PWHT) of 175 °C for 5 and 12 h was given to the weldments for all welding conditions and the mechanical properties and microstructure were re-evaluated. The hardness and strength were partially recovered and this was attributed to the possible re-precipitation of the β″ precipitates. The grain size barely exhibited a change, whereas the texture displayed a significant diminish in the Goss orientation after PWHT.     

Development of a process envelope for friction stir welding of DH36 steel – A step change

Friction stir welding of steel presents an array of advantages across many industrial sectors compared to conventional fusion welding techniques. However, the fundamental knowledge of the friction stir welding process in relation to steel remains relatively limited. A microstructure and property evaluation of friction stir welded low alloy steel grade DH36 plate, commonly used in ship and marine applications has been undertaken. In this comprehensive study, plates of 2000 × 200 × 6 mm were butt welded together at varying rotational and traverse speeds. Samples were examined microscopically and by transverse tensile tests. In addition, the work was complemented by Charpy impact testing and micro-hardness testing in various regions of the weld. The study examined a wide range of process parameters; from this, a preliminary process parameter envelope has been developed and initial process parameter sets established that produce commercially attractive excellent quality welds through a substantial increase in the conventionally recognised weld traverse speed.