Crystallization,melting behavior,and wettability of poly(ε‐caprolactone) and poly(ε‐caprolactone)/ poly(N‐vinylpyrrolidone) blends

Both wettability and crystallizability control poly(ε‐caprolactone)'s (PCL) further applications as biomaterial. The wettability is an important property that is governed by both chemical composition and surface structure. In this study, we prepared the PCL/poly(N‐vinylpyrrolidone) (PVP) blends via successive in situ polymerization steps aiming for improving the wettability and decreasing crystallizability of PCL. The isothermal crystallization of PCL/PVP at different PVP concentrations was carried out. The equilibrium melting point (T), crystallization rate, and the melting behavior after isothermal crystallization were investigated using differential scanning calorimetry (DSC). The Avrami equation was used to fit the isothermal crystallization. The DSC results showed that PVP had restraining effect on the crystallizability of PCL, and the crystallization rate of PCL decreased clearly with the increase of PVP content in the blends. The X‐ray diffraction analysis (WAXD) results agreed with that. Water absorptivity and contact angle tests showed that the hydrophilic properties were improved with the increasing content of PVP in blends. The coefficient for the water diffusion into PCL/PVP blends showed to be non‐Fickian in character. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Microstructure and properties of novel fluorescent pyrene functionalized PANI/P(VDF‐HFP) blend

We herein report the preparation and properties of the first polymer blend using pyrene functionalized polyaniline (pf‐PANI). The pf‐PANI has been synthesized and its blend has been prepared with the copolymer of vinylidene fluoride and hexafluoropropylene P(VDF‐HFP). The FTIR results reveal intermolecular interaction between the polar amide group of pf‐PANI and the polarized CH₂ group of P(VDF‐HFP). The crystalline phase of PVDF of the copolymer revealed a transformation from α to β crystalline form after blending with pf‐PANI, as found from FTIR and XRD measurements. The calorimetric measurements together with DMA results revealed the blend is partially miscible. The SEM measurements showed that the pf‐PANI has been dispersed uniformly in the P(VDF‐HFP) matrix. The solution photoluminescence spectrum of the pf‐PANI exhibited emission in the purple–blue region and is slightly red shifted for the blend. The possible applications of this flexible fluorescent pf‐PANI/P(VDF‐HFP) has been suggested. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40162.     

Electrospun PLA/PCL fibers with tubular nanoclay: Morphological and structural analysis

Biodegradable polymers are good candidates for a wide range of applications in tissue engineering and drug delivery because of their biocompatibility, their degradation, mechanical properties, and offer a sustained release of encapsulated drugs. The electrospun polymer nanofibrous materials can be used as carriers for hydrophobic and hydrophilic drugs. This research work focused on poly(lactic acid) (PLA) and blends of PLA with poly (ε‐caprolactone) (PCL) that are reinforced with different concentrations of halloysite nanotubes (HNTs) and various cosolvents for electrospinning including chloroform : acetone, chloroform : methanol, and dichloromethane (DCM) : N,N, dimethylformamide (DFM). The fibers produced from the DCM : DMF system without HNTs were more uniform resulting in smaller fiber diameters as compared to the chloroform: methanol system due to the increased solution conductivity. The addition of HNT nanoparticles produced electrospun fibers with large diameters because the viscosity of the solution increased. Cosolvent was important in determining fiber diameters because it strongly influenced the solution viscosity and conductivity. HNTs had relatively small impact on the growth of a crystalline morphology in PCL–HNT composites. The solvent mixture of chloroform : methanol was better for PLA‐based systems since PLA was found to have slightly higher crystallinity and larger enthalpy value indicating the improved structural orderness in the PLA polymer matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A comparative study of fracture behavior between carbon black/poly(ethylene terephthalate) and multiwalled carbon nanotube/poly(ethylene terephthalate) composite films

Fracture behavior of amorphous poly(ethylene terephthalate) (PET) films added multiwalled carbon nanotube (MWCNT) has been compared with that of the PET films added with carbon black (CB) to elucidate the effects of the large aspect ratio of MWCNT. Fracture toughness has been evaluated using the essential work of fracture tests. Evolution of the crazes has been analyzed by conducting time‐resolved small‐angle X‐ray scattering measurements during tensile deformation of the films at room temperature using synchrotron radiation. CB and MWCNT increased the fracture toughness of the PET film by increasing the plastic work of fracture. This resulted from the effects of the fillers to prevent the localization of deformation upon the crazes formed at earlier stages of tensile deformation and to retard the growth of the fibrils in the crazes to a critical length. The CB particles provided a number of sites where the crazes were preferably formed due to stress concentration. In the case of MWCNT, on the other hand, the widening of the crazes formed at earlier stages was suppressed due to the bridging effect arising from the large aspect ratio of MWCNT. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Realizing the enhancement of interfacial interaction in semicrystalline polymer/filler composites via interfacial crystallization

Polymer/filler composites have been widely used in various areas. One of the keys to achieve the high performance of these composites is good interfacial interaction between polymer matrix and filler. As a relatively new approach, the possibility to enhance polymer/filler interfacial interaction via crystallization of polymer on the surface of fillers, i.e., interfacial crystallization, is summarized and discussed in this paper. Interfacial crystallization has attracted tremendous interest in the past several decades, and some unique hybrid crystalline structures have been observed, including hybrid shish-kebab and hybrid shish-calabash structures in which the filler served as the shish and crystalline polymer as the kebab/calabash. Thus, the manipulation of the interfacial crystallization architecture offers a potential highly effective route to achieve strong polymer/filler interaction. This review is based on the latest development of interfacial crystallization in polymer/filler composites and will be organized as follows. The structural/morphological features of various interfacial crystallization fashions are described first. Subsequently, various influences on the final structure/morphology of hybrid crystallization and the nucleation and/or growth mechanisms of crystallization behaviors at polymer/filler interface are reviewed. Then recent studies on interfacial crystallization induced interfacial enhancement ascertained by different research methodologies are addressed, including a comparative analysis to highlight the positive role of interfacial crystallization on the resultant mechanical reinforcement. Finally, a conclusion, including future perspectives, is presented.