Friction and wear properties of basalt fiber reinforced/solid lubricants filled polyimide composites under different sliding conditions

Short basalt fibers (BFs)‐reinforced polyimide (PI) composites filled with MoS₂ and graphite were fabricated by means of hot‐press molding technique. The tribological properties of the resulting composites sliding against GCr15 steel ring were investigated on a model ring‐on‐block test rig. The wear mechanisms were also comparatively discussed, based on scanning electron microscopic examination of the worn surface of the PI composites and the transfer film formed on the counterpart. Experimental results revealed that MoS₂ and graphite as fillers significantly improved the wear resistance of the BFs‐reinforced polyimide (BFs/PI) composites. For the best combination of friction coefficient and wear rate, the optimal volume content of MoS₂ and graphite in the composites appears to be 40 and 35%, respectively. It was also found that the tribological properties of the filled BFs/PI composites were closely related with the sliding conditions such as sliding speed and applied load. Research results show that the BF/PI composites exhibited better tribological properties under higher PV product. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Friction and wear behavior of basalt‐fabric‐reinforced/solid‐lubricant‐filled phenolic composites

To improve the tribological properties of basalt‐fabric‐reinforced phenolic composites, solid lubricants of MoS₂ and graphite were incorporated, and the tribological properties of the resulting basalt‐fabric composites were investigated on a model ring‐on‐block test rig under dry sliding conditions. The effects of the filler content, load, and sliding time on the tribological behavior of the basalt‐fabric composites were systematically examined. The morphologies of the worn surfaces and transfer films formed on the counterpart steel rings were analyzed by means of scanning electron microscopy. The experimental results reveal that the incorporation of MoS₂ significantly decreased the friction coefficient, whereas the inclusion of graphite improved the wear resistance remarkably. The results also indicate that the filled basalt‐fabric composites seemed to be more suitable for friction materials serving under higher loads. The transfer films formed on the counterpart surfaces during the friction process made contributions to the reduction of the friction coefficient and wear rate of the basalt‐fabric composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of solid lubricant reinforcement on wear behavior of Kevlar fabric composites

The friction and wear behavior of Kevlar fabric composites reinforced by PTFE or graphite powders was investigated using a Xuanwu‐III friction and wear tester at dry sliding condition, with the unfilled Kevlar fabric composite as a reference. The worn surfaces were analyzed by means of scanning electron microscope, and X‐ray photoelectron spectroscopy. It was found that PTFE or graphite as fillers could significantly improve the tribological behavior of the Kevlar fabric composites, and the Kevlar fabric composites filled with 20% PTFE exhibited the best antiwear and antifriction ability among all evaluated cases. The transfer films established with two lubricants in sliding wear of composites against metallic counterparts made contributions to reducing friction coefficient and wear rate of Kevlar fabric composites. In particular, FeF₂ generated in the sliding of Kevlar fabric composites filled with PTFE against counterpart pin improved the bonding strength between the transfer film and counterpart surface, which accounted for the lowest friction coefficient and wear rate of the Kevlar fabric composites filled with PTFE measured in the testing. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Improvement of the tribological behavior of ultra‐high‐molecular‐weight polyethylene by incorporation of poly (phenyl p‐hydroxyzoate)

Ultra‐high‐molecular‐weight polyethylene/poly (phenyl p‐hydroxyzoate) composites (coded as UHMWPE/PPHZ) were prepared by compression molding. The effects of the poly (phenyl p‐hydroxyzoate) on the tribological properties of the UHMWPE/PPHZ composites were investigated, based on the evaluations of the tribological properties of the composites with various compositions and the examinations of the worn steel surfaces and composites structures by means of scanning electron microscopy and transmission electron microscopy. It was found that the incorporation of the PPHZ led to a significant decrease in the wear rate of the composites. The composites with the volume fraction of the PPHZ particulates within 45% ～ 75% showed the best wear resistance. The friction coefficient of the UHMWPE/PPHZ composites decreased with increasing load and sliding velocity, while the wear rates increased with increasing load. This was attributed to the enhanced softening and plastic deformation of the composites at elevated load or sliding velocity. The UHMWPE/PPHZ composites of different compositions had differences in the microstructures and the transfer film characteristics on the counterpart steel surface as well. This accounted for their different friction and wear behaviors. The transfer film of the UHMWPE/PPHZ composites appeared to be thinner and more coherent, which was largely responsible for their better wear resistance of t composite than the UHMWPE matrix. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2336–2343, 2005     

Tribological behavior of polyetheretherketone composites containing short carbon fibers and potassium titanate whiskers in dry sliding against steel

Polyetheretherketone (PEEK) composites reinforced by short carbon fibers (SCF) and potassium titanate whiskers (PTW) were prepared using twin‐screw extrusion compounding and injection molding. The tribological properties of hybrid composites were investigated in dry sliding condition against steel. The effects of filler contents on the wear behavior were studied. It was found that the hybrid composite showed an excellent tribological property in dry sliding condition. Applied load had great effect on the tribological behavior of the composites. In most cases, the friction coefficient of the composite decreased with the load rising. The composites with higher CF contents showed outstanding tribological performances at low load but could worsen the wear behavior at high load. Because of the positive effect of PTW, high PTW loading composites presented low wear rate at low load. At high loads, the composites with lower PTW contents had better wear resistance. The scanning electron microscopy (SEM) observation revealed that abrasion wear was attributed to the lower wear resistance of the high PTW content composite at high load. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Tribological behavior of Kevlar fabric composites filled with nanoparticles

The friction and wear characteristics of ZnO‐ or montmorillonite‐nanoparticle‐filled Kevlar fabric composites with different filler proportions when sliding against stainless steel pins under dry friction conditions were studied, with unfilled Kevlar fabric composites used as references. The worn surface and transfer film of Kevlar fabric composites were then examined with a scanning electron microscope. It was found that ZnO and montmorillonite as fillers could improve the tribological behavior of the Kevlar fabric composites with various applied loads, and the best antiwear property was obtained with the composites containing 5 wt % ZnO or montmorillonite. This indicated that these nanoparticles could prevent the destruction of Kevlar fabric composites during the friction process. The transfer film established by these nanoparticles during the sliding wear of the composites against their metallic counterpart made contributions to reducing the friction coefficient and wear rate of the Kevlar fabric composites measured in the test. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Tribological properties of SiO2 nanoparticle filled–phthalazine ether sulfone/phthalazine ether ketone (50/50 mol %) copolymer composites

SiO₂ nanoparticle filled–poly(phthalazine ether sulfone ketone) (PPESK) composites with various filler volume fractions were made by heating compression molding. The tribological behavior of the PPESK composites was investigated using a block‐on‐ring test rig by sliding PPESK‐based composite blocks against a mild carbon steel ring. The morphologies of the worn composite surfaces, wear debris, and the transferred films formed on the counterpart steel surface were examined with a scanning electron microscope, whereas the chemical state of the Fe element in the transfer film was analyzed with X‐ray photoelectron spectroscopy. In addition, IR spectra were taken to characterize the structure of wear debris and PPESK composites. It was found that SiO₂ nanoparticle filled–PPESK composites exhibit good wear resistance and friction‐reduction behavior. The friction and wear behavior of the composites was improved at a volume fraction between 4.2 and 14.5 vol % of the filler SiO₂. The results based on combined SEM, XPS, and IR techniques indicate that SiO₂ nanoparticle filled–PPESK composite is characterized by slight scuffing in dry sliding against steel and polishing action between composite surface and that of the countpart ring, whereas unfilled PPESK is characterized by severe plastic deformation and adhesion wear. In the former case a thin, but not complete, transfer film was formed on the surface of the counterpart steel, whereas in the latter case, a thick and lumpy transfer film was formed on the counterpart steel surface. This accounts for the different friction and wear behavior of unfilled PPESK and SiO₂ nanoparticle filled–PPESK composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2136–2144, 2002     

Investigations of the tribological properties of carbon fabric reinforced phenolic polymer composites filled with several nanoparticles

The carbon fabric composites filled with several nanoparticles were prepared by dip‐coating and hot press molding technique. The friction and wear behavior of the resulting composites were studied systematically using a block‐on‐ring arrangement. Experimental results showed that the optimal content of nanoparticles as fillers contributed to improve the tribological properties of the carbon fabric composites. Moreover, the friction and wear properties of the fabric composites were closely dependent with the sliding conditions. The differences in the transfer film formed on the counterpart surface during the friction process also accounted for the friction and wear behavior of carbon fabric composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Tribological behavior of three‐dimensional braided carbon fiber reinforced polyetheretherketone composites

Three‐dimensional (3D) braided carbon fiber reinforced polyetheretherketone (denoted as CF_3D/PEEK) composites with various fiber volume fractions were prepared via hybrid woven plus vacuum heat‐pressing technology and their tribological behaviors against steel counterpart with different normal loads at dry sliding were investigated. Contrast tribological tests with different lubricants (deionized water and sea water) and counterparts made from different materials (epoxy resin, PEEK) were also conducted. The results showed that the incorporation of 3D braided carbon fiber can greatly improve the tribological properties of PEEK over a certain range of carbon fiber volume fraction (V_f) and an optimum fiber loading of ∼54% exists. The friction coefficient of the CF_3D/PEEK composites decreased from 0.195 to 0.173, while the specific wear rate increased from 1.48 × 10⁻⁷ to 1.78 × 10⁻⁷ mm³ Nm⁻¹ with the normal load increasing from 50 to 150 N. Abrasive mechanism was dominated when the composites sliding with GCr15 steel counterpart under dry and aqueous lubrication conditions. Deionized water and sea water lubricants both significantly reduced the wear of the CF_3D/PEEK composites. When sliding with neat PEEK counterpart, the CF_3D/PEEK composites possess lower friction coefficient than those against epoxy resin and GCr15 steel counterparts. In general, CF_3D/PEEK composites possess excellent tribological properties and comprehensive mechanical performance, which makes it become a potential candidate for special heat‐resisting tribological components. POLYM. COMPOS., 36:2174–2183, 2015. © 2014 Society of Plastics Engineers     

Effect of nanometer SiC filler on the tribological behavior of PEEK under distilled water lubrication

The composites of polyetheretherketone (PEEK) filled with nanometer SiC of different proportions were prepared by compression molding. The tribological behaviors of the composites under lubrication of distilled water were investigated and compared with that under dry sliding, on an M‐200 friction and wear test rig, by running a plain carbon steel (AISI 1045 steel) ring against the composite block. The worn surfaces of nanometer SiC filled‐PEEK and the transfer film were observed by means of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). As the results, nanometer SiC as the filler greatly improves the wear resistance of PEEK under dry sliding and distilled water lubrication, though the composites show different dependence of wear resistance on the filler content. Nanometer SiC‐filled PEEK showed signs of slight scuffing under distilled water lubrication, while a thin, uniform, and tenacious transfer film was formed on the surface of the counterpart steel ring. On the contrary, unfilled PEEK under lubrication of water showed signs of severe plowing and erosion, while the worn surface of the counterpart ring was very rough, and a discontinuous PEEK transfer film was formed. Thus, the different friction and wear behaviors of unfilled PEEK and nanometer SiC‐filled PEEK can be attributed to the different characteristics of the corresponding transfer films. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 609–614, 2000     

聚酰亚胺/聚全氟乙丙烯层压复合材料摩擦性能研究

用热压法制备了聚酰亚胺/聚全氟乙丙烯层压复合材料.用磨损试验机在不同滑动速率、负载下研究了其摩擦学性能.对不同负载、滑动速率下的摩擦系数随时间的变化进行了详细分析.用扫描电子显微镜观测了试样的磨损面并分析了其摩擦机理.实验结果表明,该材料具有优良的摩擦学性能并且磨合时间很短.摩擦系数随时间变化,并且与负载和滑动速率有关...     

Effects of the combination of solid lubricants and short carbon fibers on the sliding performance of poly(ether imide) matrix composites

Solid lubricants, that is, graphite flakes and poly(tetrafluoroethylene) powders, were incorporated with short carbon fibers into a poly(ether imide) matrix to improve the tribological performance. Wear tests were performed with a polymer pin against a mild steel counterpart at a constant sliding speed of 1 m/s under various temperatures and contact pressures. Composites filled with equilibrium contents of solid lubricants and short carbon fibers, that is, 10 vol % of each filler, exhibited the lowest wear rate and friction coefficient. The relatively lower concentration of solid lubricants adversely affected the wear resistance, whereas the friction coefficient did not vary significantly in comparison with the friction coefficient of the composites filled with only short carbon fibers. The improved tribological behavior was attributed to more continuous and effective friction films formed on the material pairs during sliding. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1428–1434, 2004     

Tribological behaviors of polytetrafluoroethylene composites under dry sliding and seawater lubrication

The composites of polytetrafluoroethylene (PTFE) filled with expanded graphite (EG), poly(p‐oxybenzoyl) (POB), and basalt fiber (BF) were prepared by heating compression and sintering molding. The tribological behavior of PTFE composites was investigated with a pin‐on‐disk tester under dry conditions and seawater lubrication. The worn surface of PTFE composites and the transfer film on the counterface were observed with a scanning electron microscope. The results indicated that the incorporation of EG and POB improved the hardness of PTFE composites, and addition of BF led to greater load‐carrying capacity. Compared to pure PTFE, the coefficients of friction of PTFE composites slightly increased, but the wear rates were significantly reduced (the wear rate of composite with 3% EG being only 10.38% of pure PTFE). In addition, all the composites exhibited a lower coefficient of friction (decreases of about 0.03–0.07) but more serious wear under seawater lubrication than under dry sliding. The wear mechanism changed from serious abrasive wear of pure PTFE to slight adhesion wear of PTFE composites under both conditions. A transfer film was obviously found on the counterface in seawater, but it was not observed under dry conditions. Among all the materials tested, the PTFE‐based composite containing 20% POB (mass fraction), 2% EG, and 3% BF exhibited the best comprehensive performance. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2523–2531, 2013     

Comparative study on the tribological properties of the polyimide composites reinforced with different fibers

In this study, friction and wear of polyimides reinforced by carbon, glass, aramid, and nano‐alumina fibers were studied and comparatively evaluated against Si₃N₄ on a ball‐on‐disk test rig under dry rotating and reciprocating sliding, and coefficient of friction and wear rate were considered as responses. The worn surfaces of the composites were examined by scanning electron microscopy to reveal wear mechanisms of the materials' damage. Wear mechanisms are found to be dependent on the test conditions and mechanical properties of the composites itself. It was proven that different reinforcements had different effects on the friction and wear behavior of the polyimide composites to a great extent. The testing condition also had an important role on the tribological properties of the same materials. The best performance was shown by glass fiber‐reinforced polyimide composites owing to their excellent strength and hardness which can share the applied load on the sliding surface. POLYM. COMPOS., 37:2541–2548, 2016. © 2015 Society of Plastics Engineers     

Taguchi method to optimize the micron and submicron size cenosphere particulates filled E‐glass fiber‐reinforced vinylester composites

In this work, the mechanical and tribological characteristics of E‐glass fiber‐reinforced vinylester composites have been investigated experimentally under dry sliding conditions. The E‐glass fiber‐reinforced vinylester composites with uniform micron and submicron size cenosphere particulates of three different sizes (2 µm, 900 nm, and 400 nm) had been prepared in the laboratory. In this work the effect of parameters such as applied normal load, particulate size, sliding speed, sliding distance and roughness on friction and wear behavior have been carried. A plan of experiments, based on the Taguchi design, was performed to acquire data in a controlled way. An orthogonal array L₂₇ (3¹³) and Analysis of variance (ANOVA) have been applied to investigate the influence of process parameters on the coefficient of friction (COF) and sliding wear behavior of these composites. It was found that the submicron size particulates 400 nm as filler contributed significantly to improve the mechanical properties and wear resistance of the composites. The experimental results indicate that the specific wear rate is greatly influenced by applied normal load and particle size. ANOVA results showed that the applied normal load significantly influence the specific wear rate of cenosphere filled glass fiber‐reinforced vinylester composites. Regression analysis is carried to check the suitability of the prediction equation and modeling of the wear parameters and the typical R² values for COF and specific wear rate are 86.7 and 94.3%, respectively. The scanning electron microscopy are used clarify the experimental in the frictional and wear testing. POLYM. COMPOS., 35:775–787, 2014. © 2013 Society of Plastics Engineers     

Friction and wear of fiber reinforced polyimide composites in electron or proton irradiation

The polyimide (PI) composites reinforced with carbon fibers, glass fibers, and aramid fibers were fabricated by means of a hot‐press molding technique and irradiated by electron or proton for a certain time. The friction and wear behavior after irradiation, sliding against GCr15 steel balls, were evaluated in a ground‐based simulation facility using ball‐on‐disk tribosystem. The change of the chemical composition of the radiated surface was examined by X‐ray photoelectron spectroscopy. The worn morphologies and radiated surfaces of the materials were observed by scanning electron microscope to reveal the wear mechanism. Experimental analysis indicated that the chemical composition of the materials changed and an irradiated layer was formed at the surface. This irradiation layer had an important effect on the friction and wear behavior of the PI composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40774.     

Effects of various kinds of fillers on the tribological behavior of polytetrafluoroethylene composites under dry and oil‐lubricated conditions

Polytetrafluoroethylene (PTFE)‐based composites filled with various inorganic fillers in a volume fraction of 30% were prepared. The tribological behavior of the PTFE composites sliding against AISI52100 steel under dry and liquid paraffin‐lubricated conditions was investigated on an MHK‐500 model ring‐on‐block test rig. The morphologies of worn surfaces and wear debris were observed with a scanning electron microscope (SEM) and an optical microscope. As the results, different fillers show different effects on the tribological behavior of the PTFE composites, while the composite shows much different tribological behavior under lubricated conditions as compared with dry sliding. The tribological behavior of the PTFE composites under dry sliding is greatly related to the uniformity and thickness of the transfer films. Only the PTFE composites with a transfer film of good uniformity and proper thickness may have excellent tribological behavior. The PTFE composites show much better tribological behavior under lubrication of liquid paraffin than under dry sliding, namely, the friction coefficients are decreased by 1 order of magnitude and the wear rate by 1–3 orders of magnitude. Observation of the worn composite surfaces with SEM indicates that fatigue cracks were generated under lubrication of liquid paraffin, owing to the absorption and osmosis of liquid paraffin into the microdefects of the PTFE composites. The creation and development of the fatigue cracks led to fatigue wear of the PTFE composites. This would reduce the mechanical strength and load‐supporting capacity of the PTFE composites. Therefore, the tribological behavior of the PTFE composites under lubrication of liquid paraffin is greatly dependent on the compatibility between the PTFE matrix and the inorganic fillers. In other words, the better is the compatibility between PTFE and fillers the better is the tribological behavior of the composites. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1891–1897, 2001     

碱液中晶须增强PEEK复合材料的摩擦磨损性能

研究了不同含量PTW增强PEEK复合材料在碱液中的摩擦磨损性能,并与经典的CF增强PEEK复合材料对比,借助于SEM分析了磨损面和对偶面微观形貌,探讨了相关机理。结果表明,干摩擦时15%(质量)PTW增强PTFE/PEEK复合材料耐磨性是相同含量CF增强时的10.5倍。在碱液中,CF增加了PTFE/PEEK复合材料的摩擦系数、降低了其耐磨性能,而PTW可以进一步降低PTFE/PEEK复合材料的摩擦系数、明显地提高其耐磨性能。含5%PTW可提高PTFE/PEEK复合材料碱液中耐磨性2.36倍。碱液阻止了对偶面转移膜的形成,犁削和磨粒磨损是CF增强PEEK复合材料碱液中的主要磨损机制,而隧道状晶体结构和细微尺寸的纤维态形貌使得PTW在碱液中仍具有显微增强耐磨作用。     

Surface modification of carbon fiber and its effects on the mechanical and tribological properties of the polyurethane composites

To improve the friction and wear behavior of the polyurethane composites, carbon fibers were modified with 2, 4‐diisocyanatotoluene. The mechanical and tribological properties of the reinforced polyurethane composites were studied. Tensile strength of the composites increased with the addition of carbon fibers. The friction and wear experiments were tested on a MRH‐3 model ring‐on‐block test rig at different sliding speeds and loads under dry sliding. Experimental results revealed that carbon fibers with chemical treatment contributed to largely improve the tribological properties of the polyurethane composites. Scanning electron microscopic (SEM) investigations showed that the worn surface of the modified polyurethane composite was smoother than pure polyurethane under given load and sliding speed. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Action of transfer film in improving friction and wear behaviors of iron‐ and copper‐filled poly(ether ether ketone) composites

The composites of poly(ether ether ketone) (PEEK) filled with micrometer‐sized Cu and Fe particles were prepared by compression molding. The friction and wear behaviors of the composites were examined on a pin‐on‐disc friction‐and‐wear tester by sliding PEEK‐based composites against tool steel at a sliding speed of 1.0 m s⁻¹ and a normal load of 19.6N. Optical microscopic analysis of the transfer film and of the worn pin surfaces and wear debris was performed to investigate the wear mechanisms of the composites. It was found that Cu and Fe used as filler considerably decreased the wear rate of PEEK. A thin, uniform, and tenacious transfer film was formed when Cu was used as the filler, and a nonuniform and thick transfer film was formed when Fe was used as the filler. The transfer film played a key role in increasing the wear resistance of the PEEK composites. Plastic deformation was dominant for wear of PEEK–Cu, while abrasion and adhesion were dominant for wear of PEEK–Fe. Because of the strong affinity between Fe as filler and its identical counterpart in the counterface tool steel surface, the adhesion between the PEEK–Fe composite surface and the counterface tool steel surface was thus severe. This contributed to the generation of a thicker transfer film for PEEK–Fe. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 179–184, 2000