Effect of bis(diisopropyl)thiophosphoryl disulfide on the covulcanization of styrene–butadiene rubber and ethylene–propylene–diene (monomer) blends

Covulcanization of elastomer blends constituting styrene–butadiene rubber (SBR) and ethylene–propylene–diene (monomer) rubber (EPDM) was successfully performed in the presence of reinforcing fillers like carbon black and silica by using a multifunctional rubber additive, bis(diisopropyl)thiophosphoryl disulfide (DIPDIS). The polarity of EPDM rubber was increased by a two‐stage vulcanization technique, which allowed the formation of rubber‐bound intermediates. In this way the migration of both curatives and reinforcing fillers in the EPDM–SBR blend could be controlled and cure rate mismatch could be minimized. The process significantly improved the physical properties of the blend vulcanizates. The phase morphology, as evident from the SEM micrographs, was indicative of the presence of a much more compact and coherent rubber matrix in the two‐stage vulcanizates. Different accelerator systems were studied to understand better the function and effectiveness of DIPDIS in developing homogeneity in the blends of dissimilar elastomers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1231–1242, 2004     

Mechanical and aging properties of cross‐linked ethylene propylene diene rubber / styrene butadiene rubber blends

The mechanical properties and aging characteristics of blends of ethylene propylene diene monomer (EPDM) rubber and styrene butadiene rubber (SBR) were investigated with special reference to the effect of blend ratio and cross‐linking systems. Among the blends, the one with 80/20 EPDM/SBR has been found to exhibit the highest tensile, tear, and abrasion properties at ambient temperature. The observed changes in the mechanical properties of the blends have been correlated with the phase morphology, as attested by scanning electron micrographs (SEMs). The effects of three different cure systems, namely, sulfur (S), dicumyl peroxide (DCP), and a mixed system consisting of sulfur and peroxide (mixed) on the blend properties also were studied. The stress‐strain behavior, tensile strength, elongation at break, and tear strength of the blends were found to be better for the mixed system. The influence of fillers such as high‐abrasion furnace (HAF) black, general‐purpose furnace (GPF) black, silica, and clay on the mechanical properties of 90/10 EPDM/SBR blend was examined. The ozone and water aging studies also were conducted on the sulfur cured blends, to supplement the results from the mechanical properties investigation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2606–2621, 2004     

Dynamic mechanical properties of thermoplastic elastomers from polypropylene–natural rubber blend

The dynamic mechanical properties of thermoplastic elastomers from polypropylene natural rubber blends have been evaluated with special reference to the effect of blend ratio and extent of dynamic crosslinking of the elastomer phase. The effects of HAF black and silica fillers have also been studied. It has been found that increasing the proportion of elastomer phase reduced the storage modulus and increased the loss tangent values of the blends. The effect of dynamic crosslinking was found to be more prominent in blends containing higher proportion of elastomer phase. The improvement in storage modulus and decrease in loss tangent values were quite remarkable with increase in extent of crosslinking in these blends. The 70:30 NR:PP blend was found to exist as a two-phase system, both the components forming continuous phases of the blend.     

Some considerations concerning the dynamic mechanical properties of cured styrene–butadiene rubber/polybutadiene blends

The dynamic mechanical response of several binary mixtures of a styrene–butadiene copolymer and high cis‐polybutadiene has been studied. The loss tangent and shear modulus were measured with a free damping torsion pendulum at temperatures between 143 and 343 K in argon atmosphere. From the loss tangent data the glass transition temperature of each sample was evaluated. The results can be represented by the Fox equation that relates the glass transition temperature of the blend with that of constituent polymers. The influence in the loss tangent data of the crystallization of the high cis BR used in the blend is discussed. A study of the separation of the crystalline and amorphous parts in the polybutadiene using the storage modulus data is presented. Finally, the loss of crystallinity at different contents of SBR in the blend is analysed using the dynamic mechanical data. © 2000 Society of Chemical Industry     

Influence of calcium carbonate filler and mixing type process on structure and properties of styrene–acrylonitrile/ethylene–propylene–diene polymer blends

The properties of styrene–acrylonitrile (SAN) and ethylene–propylene–diene (EPDM) blends containing different types of calcium carbonate filler were studied. The influence of mixing type process on the blend properties was also studied. Two different mixing processes were used. The first one includes mixing of all components together. The other process is a two‐step mixing procedure: masterbatch (MB; EPDM/SAN/filler blend) was prepared and then it was mixed with previously prepared polymer blend. Surface energy of samples was determined to predict the strength of interactions between polymer blend components and used fillers. The phase morphology of blends and their thermal and mechanical properties were studied. From the results, it can be concluded that the type of mixing process has a strong influence on the morphological, thermal, and mechanical properties of blends. The two‐step mixing process causes better dispersion of fillers in blends as well as better dispersion of EPDM in SAN matrix, and therefore, the finest morphology and improved properties are observed in blends with MB. It can be concluded that the type of mixing process and carefully chosen compatibilizer are the important factors for obtaining the improved compatibility of SAN/EPDM blends. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of dynamic crosslinking on tensile yield behavior of polypropylene/ethylene‐propylene‐diene rubber blends

Tensile yield behavior of the blends of polypropylene (PP) with ethylene‐propylene‐diene rubber (EPDM) is studied in blend composition range 0–40 wt % EPDM rubber. These blends were prepared in a laboratory internal mixer by simultaneous blending and dynamic vulcanization. Vulcanization was performed with dimethylol phenolic resin. For comparison, unvulcanized PP/EPDM blends were also prepared. In comparison to the unvulcanized blends, dynamically vulcanized blends showed higher yield stress and modulus. The increase of interfacial adhesion caused by production of three‐dimensional network is considered to be the most important factor in the improvement. It permits the interaction of the stress concentrate zone developed at the rubber particles and causes shear yielding of the PP matrix. Systematic changes with varying blend composition were found in stress‐strain behavior in the yield region, viz., in yield stress, yield strain, width of yield peak, and work of yield. Analysis of yield stress data on the basis of the various expressions of first power and two‐thirds power laws of blend compositions dependence and the porosity model led to consistent results from all expression about the variation of stress concentration effect in both unvulcanized and vulcanized blend systems. Shapes and sizes of dispersed rubber phase (EPDM) domains at various blend compositions were studied by scanning electron microscopy. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2104–2121, 2000     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Electrical and mechanical properties of ethylene propylene diene monomer–chloroprene rubber blend loaded with white and black fillers

The permittivity ε′ and dielectric loss ε" for different ratios of an ethylene propylene diene monomer (EPDM)–chloroprene rubber (CR) blend ranging from 0 to 100 phr were measured over a frequency range from 400 Hz to 60 kHz. The measurements were carried out at room temperature (25°C). The values of ε′ and ε" were found to decrease with increasing EPDM content in the EPDM–CR blend. The sample which possesses the best mechanical and electrical properties was a 50 EPDM–50 CR blend. This sample was chosen to be loaded with 40 phr of some white fillers, namely, calcium carbonate, silica, silitan z, and talc. From the electrical and mechanical investigations, it was found that the use of silica and calcium carbonate in these blends could improve these properties. The electrical and mechanical properties were also studied for the investigated blends loaded with both silica and calcium carbonate with different contents (10–40 phr). It was found that 20 phr is the most promising concentration which can possess better properties. The same trend was obtained by the addition of 20 phr SRF black in addition to the white fillers to the above blends. On the other hand, from the compatibility study between both investigated rubber, it is found that both types are incompatible, in which some improvement may occur by the addition of PVC. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2061–2068, 1998     

Cure characteristics,morphology, and mechanical properties of ethylene–propylene–diene–monomer rubber/acrylonitrile butadiene rubber blends

Blends based on ethylene–propylene–diene monomer rubber (EPDM) and acrylonitrile butadiene rubber (NBR) was prepared. Sulfur was used as the vulcanizing agent. The effects of blend ratio on the cure characteristics and mechanical properties, such as stress–strain behavior, tensile strength, elongation at break, hardness, rebound resilience, and abrasion resistance have been investigated. Tensile and tear strength showed synergism for the blend containing 30% of NBR, which has been explained in terms of morphology of the blends attested by scanning electron micrographs. A relatively cocontinuous morphology was observed for 70 : 30, EPDM/NBR blend system. The experimental results have been compared with the relevant theoretical models. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of styrene–isoprene–styrene,styrene–butadiene–styrene,and styrene–butadiene–rubber on the mechanical,thermal, rheological,and morphological properties of polypropylene/polystyrene blends

The mechanical, thermal, rheological, and morphological properties of polypropylene (PP)/polystyrene (PS) blends compatibilized with styrene–isoprene–styrene (SIS), styrene–butadiene–styrene (SBS), and styrene–butadiene–rubber (SBR) were studied. The incompatible PP and PS phases were effectively dispersed by the addition of SIS, SBS, and SBR as compatibilizers. The PP/PS blends were mechanically evaluated in terms of the impact strength, ductility, and tensile yield stress to determine the influence of the compatibilizers on the performance properties of these materials. SIS‐ and SBS‐compatibilized blends showed significantly improved impact strength and ductility in comparison with SBR‐compatibilized blends over the entire range of compatibilizer concentrations. Differential scanning calorimetry indicated compatibility between the components upon the addition of SIS, SBS, and SBR by the appearance of shifts in the melt peak of PP toward the melting range of PS. The melt viscosity and storage modulus of the blends depended on the composition, type, and amount of compatibilizer. Scanning electron microscopy images confirmed the compatibility between the PP and PS components in the presence of SIS, SBS, and SBR by showing finer phase domains. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 266–277, 2003     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers     

Effects of trans-polyoctylene rubber (TOR) on the properties of NR/EPDM blends

trans-Polyoctylene rubber (TOR) was melt blended with an incompatible NR/EPDM (70/30) blend. Mixing torque and temperature were reduced as TOR was added to NR/EPDM blend. The curing characteristics of the blend were affected as TOR participated in vulcanization and became a part of network. A scanning electron micrograph demonstrated that addition of TOR improved the compatibility of the blend and thereby led to a finer phase morphology. The ozone resistance of the blends was determined in terms of a critical stress–strain parameter. The critical stored energy density for ozone cracking was significantly enhanced for the TOR containing rubber blend. It was believed that the improvement in ozone resistance arised from finely dispersed ozone-resistant EPDM particles in the blend. TOR caused an improvement in dynamic properties and an increase in tensile modulus, but a decrease in tensile stress and elongation at break of the rubber blend. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 749–756, 1999     

Fly ash particles and precipitated silica as fillers in rubbers. I. Untreated fillers in natural rubber and styrene–butadiene rubber compounds

In this study, we investigated the effects of untreated precipitated silica (PSi) and fly ash silica (FASi) as fillers on the properties of natural rubber (NR) and styrene–butadiene rubber (SBR) compounds. The cure characteristics and the final properties of the NR and SBR compounds were considered separately and comparatively with regard to the effect of the loading of the fillers, which ranged from 0 to 80 phr. In the NR system, the cure time and minimum and maximum torques of the NR compounds progressively increased at PSi loadings of 30–75 phr. A relatively low cure time and low viscosity of the NR compounds were achieved throughout the FASi loadings used. The vulcanizate properties of the FASi‐filled vulcanizates appeared to be very similar to those of the PSi‐filled vulcanizates at silica contents of 0–30 phr. Above these concentrations, the properties of the PSi‐filled vulcanizates improved, whereas those of the FASi‐filled compounds remained the same. In the SBR system, the changing trends of all of the properties of the filled SBR vulcanizates were very similar to those of the filled NR vulcanizates, except for the tensile and tear strengths. For a given rubber matrix and silica content, the discrepancies in the results between PSi and FASi were associated with filler–filler interactions, filler particle size, and the amount of nonrubber in the vulcanizates. With the effect of the FASi particles on the mechanical properties of the NR and SBR vulcanizates considered, we recommend fly ash particles as a filler in NR at silica concentrations of 0–30 phr but not in SBR systems, except when improvement in the tensile and tear properties is required. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2119–2130, 2004     

Preparation and properties of ethylene–propylene–diene rubber/organomontmorillonite nanocomposites

Ethylene–propylene–diene rubber (EPDM)/organomontmorillonite (OMMT) nanocomposites were prepared with a maleic anhydride grafted EPDM oligomer as a compatibilizer via melt intercalation. X‐ray diffraction and transmission electron microscopy indicated that the silicate layers of OMMT were exfoliated and dispersed uniformly as a few monolayers in nanocomposites. The change in the crystallization behavior of the nanocomposites was examined. The nanocomposites exhibited great improvements in the tensile strength and tensile modulus. The incorporation of OMMT gave rise to a considerable reduction of tan δ and an increase in the storage modulus. Moreover, the solvent resistance of the nanocomposites increased remarkably. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 440–445, 2004     

MWCNT/Hectorite hybrid filled acrylonitrile butadiene rubber/ ethylene-co-vinyl acetate blend nanocomposites: preparation and properties

Multiwalled carbon nanotube/hectorite hybrid filler (HMH) was prepared by simple dry grinding method. It was subsequently used for the reinforcement of technologically compatible acrylonitrile butadiene rubber (NBR)/ ethylene-co-vinyl acetate (EVA) blend through solution intercalation method. Analysis of the prepared blend nanocomposites confirms homogeneous dispersion of the constituent fillers in the polymer matrix and significant interaction between two types of constituent fillers. Mechanical properties of NBR/EVA blend are significantly improved with HMH content up to 4 wt.% followed by reversion. Maximum improvement observed in tensile strength, elongation at break and toughness are 106%, 37% and 171% respectively without significant rise in Young’s modulus. Results also show best dynamic mechanical and dielectric response at 4 wt.% and 3 wt.% HMH content respectively. Enhanced mechanical, dynamic mechanical and dielectric properties of the blend nanocomposites attained may be attributed to fair degree of compatibility between the two polymer matrices, homogeneous dispersion of fillers and improved polymer-filler interaction.     

Acrylic rubber‐fluorocarbon rubber miscible blends: Effect of curatives and fillers on cure,mechanical, aging,and swelling properties

The cure characteristics and mechanical properties of gum and filled acrylic rubber (ACM), fluorocarbon rubber (FKM), and their blends of varying compositions were studied both under unaged and aged conditions. The rheometric study showed that optimum cure properties were obtained using a mixed curing system of blocked diamine, hexamethylenediamine carbamate (Diak #1), and ammonium benzoate. From varying the curing agents, the optimum levels of Diak #1 and ammonium benzoate were found to be 1.5 and 2.5 phr, respectively. The addition of different fillers and their loading influenced the cure properties, with increased torque and reduced scorch safety. The gum and filled 50:50 (w/w) ACM‐FKM showed overall performance in strength properties. Postcuring improved the strength of all the systems, especially the systems with a higher proportion of FKM. None of the properties changed significantly during aging of the blends. FKM and the blends containing a higher proportion of FKM were affected least by aging. Swelling of the blends was reduced by the addition of fillers. Dynamic mechanical thermal analysis showed a single tan δ peak corresponding to a single phase transition for both cured and filled blends. The storage modulus of the blend increased from the gum blend to the filled blend, indicating the presence of polymer‐filler interaction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1442–1452, 2003     

Effect of the addition of acrylonitrile/ethylene–propylene–diene monomer (EPDM)/styrene graft copolymer on the morphology–properties relationships in poly(styrene‐co‐acrylonitrile)/EPDM rubber blends

Blends of poly(styrene‐co‐acylonitrile) (SAN) with ethylene–propylene–diene monomer (EPDM) rubber were investigated. An improved toughness–stiffness balance of the SAN/EPDM blend was obtained when an appropriate amount of acrylonitrile–EPDM–styrene (AES) graft copolymer was added, prepared by grafting EPDM with styrene–acrylonitrile copolymer, and mixed thoroughly with both of the two components of the blend. Morphological observations indicated a finer dispersion of the EPDM particles in the SAN/EPDM/AES blends, and particle size distribution became narrower with increasing amounts of AES. Meanwhile, it was found that the SAN/EPDM blend having a ratio of 82.5/17.5 by weight was more effective in increasing the impact strength than that of the 90/10 blend. From dynamic mechanic analysis of the blends, the glass‐transition temperature of the EPDM‐rich phase increased from ?53.9 to ?46.2°C, even ?32.0°C, for the ratio of 82.5/17.5 blend of SAN/EPDM, whereas that of the SAN‐rich phase decreased from 109.2 to 108.6 and 107.5°C with the additions of 6 and 10% AES copolymer contents, respectively. It was confirmed that AES graft copolymer is an efficient compatibilizer for SAN/EPDM blend. The compatibilizer plays an important role in connecting two phases and improving the stress transfer in the blends. Certain morphological features such as thin filament connecting and even networking of the dispersed rubber phase may contribute to the overall ductility of the high impact strength of the studied blends. Moreover, its potential to induce a brittle–ductile transition of the glassy SAN matrix is considered to explain the toughening mechanism. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1685–1697, 2004     

Preparation and characterization of acrylonitrile–styrene–methylmethacrylate terpolymer as a compatibilizer for rubber blends

Acrylonitrile‐co‐styrene‐co‐methylmethacrylate (AN‐S‐MMA) terpolymer was prepared by bulk and emulsifier‐free emulsion polymerization techniques. The bulk and emulsion terpolymers were characterized by means of Fourierr transform infrared spectroscopy, ¹³C nuclear magnetic resonance (NMR) spectroscopy, gel permeation chromatography, thermal gravimetric analysis, and elemental analysis. The kinetics of the terpolymerization were studied. The terpolymers were then incorporated into butadiene—acrylonitrile rubber (NBR)/ethylene propylene diene monomer rubber (EPDM) blends and into chloroprene rubber (CR)/EPDM blend. The terpolymers were then tested for potential as compatibilizers by using scanning electron microscopy and differential scanning calorimetry. The terpolymers improved the compatibility of CR/EPDM and NBR/EPDM blends. The physicomechanical properties of CR/EPDM and NBR/EPDM blend vulcanizates revealed that the incorporation of terpolymers was advantageous, since they resulted in blend vulcanizates with higher 100% moduli and with more thermally stable mechanical properties than the individual rubbers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3143–3153, 2003     

Physicochemical characterization of the filler–matrix interface in elastomer‐encapsulated fly ash/polyester particulate composites

An attempt was made to improve the toughness of fly ash (FA)/general‐purpose unsaturated polyester resin (GPR) composites. Elastomer [styrene–butadiene rubber (SBR) or acrylic copolymer (AC)]‐encapsulated fillers (FA or CaCO₃) were made through the coagulation of the emulsified elastomer containing the filler with constant stirring. The elastomer‐encapsulated fillers were added to GPR at concentrations as high as 15 wt % to make FA/SBR or AC/GPR composites. The mechanical properties (i.e., the tensile strength, tensile modulus, tensile elongation, flexural strength, flexural modulus, impact strength, and hardness) of FA/GPR, FA/SBR/GPR, and FA/AC/GPR composites were studied. The tensile‐fractured surfaces of all the composites were studied with scanning electron microscopy. The thermal stability was studied with thermogravimetric analysis. An analysis of the results indicate that this modification technique is rather easy and more economical than the chemical modification of filler surfaces with functional silane coupling agents. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 171–184, 2005     

Effects of shear stress and subcritical water on devulcanization of styrene–butadiene rubber based ground tire rubber in a twin‐screw extruder

The devulcanization reaction of styrene–butadiene rubber (SBR) based ground tire rubber (GTR) in GTR/ethylene–propylene–diene monomer rubber (EPDM) blend was investigated through a compound‐induced reaction by increasing screw rotation speed and being in the presence of subcritical water. The effects of temperature, pressure, screw rotation speed, or promoting agents on the gel content, Mooney viscosity, and Fourier transform infrared spectra of the sol of the devulcanized blends (devulcanized ground tire rubber (DGTR)/EPDM) were measured, and the mechanical properties and microstructures of the revulcanized blend ((DGTR/EPDM)/SBR) were characterized. The results show that subcritical water as a swelling agent and reaction medium promotes the devulcanization reaction, increases the selectivity of the crosslink breakage, keeps the extrusion material from oxidative degradation, reduces the gel particle size of the devulcanized blends, and significantly improves the mechanical properties of the revulcanized SBR/(DGTR/EPDM) blends. In subcritical water, the suitable promoting agents (alkylphenol polysulfide 450, hydrogen peroxide H₂O₂, or 450/H₂O₂) accelerate the devulcanization reaction, keep the double bond content, and lead to further decrease of the gel content and Mooney viscosity of the devulcanized blends and further increase of the mechanical properties of the revulcanized SBR/(DGTR/EPDM) blends. Especially the compound promoting agent (450/H₂O₂) improves the selectivity of the crosslink breakage in devulcanization of SBR‐based GTR. When 450/H₂O₂ is added as a compound promoting agent at the best reaction condition in subcritical water (200°C, 1.6 MPa and 1000 rpm), the tensile strength and elongation at break of the revulcanized SBR/(DGTR/EPDM) blends reach to 85.4% and 201% of vulcanized SBR (24.0 MPa, 356%), respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1845–1854, 2013