The dynamic mechanical analysis,impact, and morphological studies of EPDM–PVC and MMA‐g‐EPDM–PVC blends

The dynamic mechanical studies, impact resistance, and scanning electron microscopic studies of ethylene propylene diene terpolymer–poly(vinyl chloride) (EPDM–PVC) and methyl methacrylate grafted EPDM rubber (MMA‐g‐EPDM)–PVC (graft contents of 4, 13, 21, and 32%) blends were undertaken. All the regions of viscoelasticity were present in the E′ curve, while the E″ curve showed two glass transition temperatures for EPDM–PVC and MMA‐g‐EPDM–PVC blends, and the T_g increased with increasing graft content, indicating the incompatibility of these blends. The tan δ curve showed three dispersion regions for all blends arising from the α, β, and Γ transitions of the molecules. The sharp α transition peak shifted to higher temperatures with increasing concentration of the graft copolymer in the blends. EPDM showed less improvement while a sixfold increase in impact strength was noticed with the grafted EPDM. The scanning electron microscopy micrographs of EPDM–PVC showed less interaction between the phases in comparison to MMA‐g‐EPDM–PVC blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1959–1968, 1999     

Effect of aging on synthesis of graft copolymer of EPDM and styrene (EPDM‐g‐PS)

The effect of aging on synthesis by the graft copolymerization of styrene onto random ethylene–propylene–diene monomer with benzoyl peroxide (BPO) as the initiator is described. Results showed that yields of graft copolymer are increased in the first 10 min. After 10 min, the total polymer produced has a maximum at about 25 min. However, the portion of the graft copolymer is decreased and the portion of the pure polystyrene is increased. In addition, the influence factors, such as reaction time, temperature, BPO concentrations and styrene concentrations, effect of solvents on the extent of graft copolymerization were discussed. The extent of grafted copolymerization was verified by hexane and acetone Soxhlet (solvent extraction). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4809–4813, 2006     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Development of HDPE/EPDM‐g‐TMEVS nanocomposites with enhanced electrical and flame properties

Nanoclay reinforced HDPE/silane grafted EPDM composites have been developed using an epoxy functionalized HDPE as compatibilizer.The nanoclay has been varied from 0% to 10% in the composites along with the incorporation of compatibilizer and without compatibilizer in a brabender plasticorder.The dielectric and fire retardant properties of these nanocomposites have been examined. Addition of nanoclay enhanced char formation with increased values of limiting oxygen index. Electrical properties such as volume and surface Resistivity improved with addition of nanoclay and compatibilizer. The values of tan δ increased with increase in grafted EPDM and silanated nanoclay loading. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Analysis of mechanical,thermal, and morphological behavior of polycaprolactone/wood flour blends

In the present study, the properties of polycaprolactone (PCL) and wood flour (WF) blends were examined by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), Instron mechanical tester, and scanning electron microscopy (SEM). As for results, the mechanical properties of PCL were lowered obviously, due to the poor compatibility between the two phases, when it was blended with wood flours. A fine dispersion and homogeneity of wood flour in the polymer matrix could be obtained when the acrylic acid grafted PCL (PCL‐g‐AA) was used to replace PCL for manufacture of blends. This better dispersion is due to the formation of branched and crosslinked macromolecules since the PCL‐g‐AA copolymer had carboxyl groups to react with the hydroxyls. This is reflected in the mechanical and thermal properties of the blends. In comparison with pure PCL/WF blend, the increase in tensile strength at break was remarkable for PCL‐g‐AA/WF blend. The PCL‐g‐AA/WF blends are more easily processed than the PCL/WF ones since the former had lower melt viscosity than the latter. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1000–1006, 2004     

Relationship between structure and properties in high‐performance PA6/SEBS‐g‐MA/(PPO/PS) blends: The role of PPO and PS

This work aimed at studying the role of poly(phenylene oxide) (PPO) and polystyrene (PS) in toughening polyamide‐6 (PA6)/styrene‐ethylene‐butadiene‐styrene block copolymer grafted with maleic anhydride (SEBS‐g‐MA) blends. The effects of weight ratio and content of PPO/PS on the morphology and mechanical behaviors of PA6/SEBS‐g‐MA/(PPO/PS) blends were studied by scanning electron microscope and mechanical tests. Driving by the interfacial tension and the spreading coefficient, the “core–shell” particles formed by PPO/PS (core) and SEBS‐g‐MA (shell) played the key role in toughening the PA6 blends. As PS improved the distribution of the “core–shell” particles due to its low viscosity, and PPO guaranteed the entanglement density of the PPO/PS phase, the 3/1 weight ratio of PPO/PS supplied the blends optimal mechanical properties. Within certain range, the increased content of PPO/PS could supply more efficient toughening particles and bring better mechanical properties. Thus, by adjusting the weight ratio and content of PPO and PS, the PA6/SEBS‐g‐MA/(PPO/PS) blends with excellent impact strength, high tensile strength, and good heat deflection temperature were obtained. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45281.     

Polyhydroxybutyrate/acrylonitrile‐g‐(ethylene‐co‐ propylene‐co‐diene)‐g‐styrene blends: Their morphology and thermal and mechanical behavior

Polyhydroxybutyrate (PHB) is a biodegradable bacterial polyester emerging as a viable substitute for synthetic, semicrystalline, nonbiodegradable polymers. An elastomer terpolymer of acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene (AES) was blended with PHB in a batch mixer and in a twin‐screw extruder to improve the mechanical properties of PHB. The blends were characterized with differential scanning calorimetry, dynamic mechanical analysis, scanning electron microscopy, and impact resistance measurements. Despite the narrow processing window of PHB, blends with AES could be prepared via the melting of the mixture without significant degradation of PHB. The blends were immiscible and composed of four phases: poly(ethylene‐co‐propylene‐co‐diene), poly(styrene‐co‐acrylonitrile), amorphous PHB, and crystalline PHB. The crystallization of PHB in the blends was influenced by the AES content in different ways, depending on the processing conditions. A blend containing 30 wt % AES presented impact resistance comparable to that of high‐impact polystyrene, and the value was about 190% higher than that of pure PHB. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology,crystallization, and thermal behavior of isotactic polypropylene/propylene‐g‐styrene blends

Optical microscopy, differential scanning calorimetry, and small angle X‐ray scattering techniques were used to study the influence of the crystallization conditions on morphology and thermal behavior of samples of binary blends constituted of isotactic polypropylene (iPP) and a novel graft copolymer of unsaturated propylene with styrene (uPP‐g‐PS) isothermally crystallized from melt, at relatively low undercooling, in a range of crystallization temperatures of the iPP phase. It was shown that, irrespective of composition, no fall in the crystallinity index of the iPP phase was observed. Notwithstanding, spherulitic texture and thermal behavior of the iPP phase in the iPP/uPP‐g‐PS materials were strongly modified by the presence of copolymer. Surprisingly, iPP spherulites crystallized from the blends showed size and regularity higher than that exhibited by plain iPP spherulites. Moreover, the amount of amorphous material located in the interspherulitic amorphous regions decreased with increasing crystallization temperature, and for a given crystallization temperature, with increasing uPP‐g‐PS content. Also, relevant thermodynamic parameters, related to the crystallization process of the iPP phase from iPP/uPP‐g‐PS melts, were found, composition dependent. The equilibrium melting temperature and the surface free energy of folding of the iPP lamellar crystals grown in the presence of uPP‐g‐PS content up to 5% (wt/wt) were, in fact, respectively slightly lower and higher than that found for the lamellar crystals of plain iPP. By further increase of the copolymer content, both the equilibrium melting temperature and surface free energy of folding values were, on the contrary, depressed dramatically. The obtained results were accounted for by assuming that the iPP crystallization process from iPP/uPP‐g‐PS melts could occur through molecular fractionation inducing a combination of morphological and thermodynamic effects. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2286–2298, 2001     

Phase behavior of binary blends of PP/PP‐g‐AA: limitations of the conventional characterization techniques

In this study, miscibility/immiscibility issues of a binary blend consisting of polypropylene (PP) and acrylic acid grafted polypropylene (PP‐g‐AA) were investigated using rheometry, DSC, dynamic mechanical and thermal analysis (DMTA), AFM and time‐of‐flight secondary‐ion mass spectrometry (ToF‐SIMS). Phase separation analysis of such blend systems is a challenge and complex due to chemically similar components as well as the low value of acrylic acid groups in the graft copolymer. Thus, it is crucial to determine if the present blend shows some degree of miscibility or develops co‐continuous morphology between the components. The analysis of rheometrical, DSC and DMTA results indicated no sensitivity of these classical techniques for detecting the miscibility or immiscibility of such a system. However, AFM data effectively detected dispersed‐phase domains corresponding to the PP‐g‐AA rich phase. The results, for the first time, indicated that the start of phase separation occurs at a critical copolymer concentration between 2 and 5 wt%. Furthermore it was observed that, as the PP‐g‐AA content increases, the size and continuity of the dispersed phase increase and reach a highly continuous morphology. Additionally, ToF‐SIMS chemical imaging was carried out to aid in the interpretation of the AFM data. © 2016 Society of Chemical Industry     

Mechanical,thermal, and morphological characteristics of compatibilized and dynamically vulcanized polyoxymethylene/ethylene propylene diene terpolymer blends

Dynamically vulcanized blends of polyoxymethylene (POM) and ethylene propylene diene terpolymer (EPDM) with and without compatibilizer were prepared by melt mixing in a twin screw extruder. Maleic anhydride (MAH) grafted EPDM (EPDM‐g‐MAH) has been used as a compatibilizer. Dicumyl peroxide was used for vulcanizing the elastomer phase in the blends. Mechanical, dynamical mechanical, thermal, and morphological properties of the blend systems have been investigated as a function of blend composition and compatibilizer content. The impact strength of both dynamically vulcanized blends and compatibilized/dynamically vulcanized blends increases with increase in elastomer content with decrease in tensile strength. Dynamic mechanical analysis shows decrease in tanδ values as the elastomer and compatibilizer content increased. Thermograms obtained from differential scanning calorimetric studies reveal that compatibilized blends have lower T_m values compared to dynamically vulcanized blends, which confirms strong interaction between the plastic and elastomer phase. Scanning electron microscopic observations on impact fractured surface indicate reduction in particle size of elastomer phase and its high level of dispersion in the POM matrix. In the case of compatibilized blends high degree of interaction between the component polymers has been observed. POLYM. ENG. SCI., 47:934–942, 2007. © 2007 Society of Plastics Engineers     

Dynamic mechanical and morphological behavior of blends of polystyrene and poly[acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene] prepared by in situ polymerization of styrene

PS/AES blends were prepared by in situ polymerization of styrene in the presence of AES elastomer, a grafting copolymer of poly(styrene‐co‐acrylonitrile) – SAN and poly(ethylene‐co‐propylene‐co‐diene)–EPDM chains. These blends are immiscible and present complex phase behavior. Selective extraction of the blends' components showed that some fraction of the material is crosslinked and a grafting of PS onto AES is possible. The morphology of the noninjected blends consists of spherical PS domains covered by a thin layer of AES. After injection molding, the blends show morphology of disperse elastomeric phase morphology in a rigid matrix. Two factors could contribute to the change of morphology: (1) the stationary polymerization conditions did not allow the mixture to reach the equilibrium morphology; (2) the grafting degree between PS and AES was not high enough to ensure the morphological stability against changes during processing in the melting state. The drastic change of EPDM morphology from continuous to disperse phase has as consequence a decrease in the intensity of the loss modulus peaks corresponding to the EPDM glass transition. However, the storage modulus at temperatures between the glass transition of EPDM and PS/SAN phases does not change significantly. This effect was attributed to the presence of the SAN rigid chains in the AES. © 2009 Wiley Periodicals, Inc. Journal of Applied Polymer Science, 2009     

Improvement of mechanical properties for PP/PS blends by in situ compatibilization

The effect of the in situ compatibilization on the mechanical properties of PP/PS blends was investigated. The application of Friedel-Crafts alkylation reaction to the PP/PS-blend compatibilization was assessed. Styrene/AlCl₃ was used as catalyst system. The graft copolymer (PP-g-PS) formed at the interphase showed relatively high emulsifying strength. Scission reactions, occurring in parallel with grafting, were verified for PP and PS at high catalyst concentration, but no crosslinking reactions were detected. Tensile tests were performed on dog-bone specimens of the blends. Both elongation at break and toughness increased with catalyst concentration. At 0.7% AlCl₃, a maximum was reached, which amounted to five times the value of the property for the uncompatibilized blend. At higher catalyst concentrations these properties decreased along with the PP molecular weight due to chain-scission reactions. On the other hand, the tensile strength did not change with the catalyst concentration. The in situ compatibilized blends showed considerable improvement in mechanical properties, but were adversely affected by chain scissions at high catalyst contents.     

Effect of in situ synthesized macroactivator on morphology of PA6/PS blends via successive polymerization

In situ polymerization and in situ compatibilization was adopted for preparation of ternary PA6/PS‐g‐PA6/PS blends by means of successive polymerization of styrene, with TMI and ε‐caprolactam, via free radical copolymerization and anionic ring‐opening polymerization, respectively. Copolymer poly(St‐g‐TMI), the chain of which bears isocyanate (? NCO), acts as a macroactivator to initiate PA6 chain growth from the PS chain and graft copolymer of PS‐g‐PA6 and pure PA6 form, simultaneously. The effect of the macroactivator poly(St‐g‐TMI) on the phase morphology was investigated in detail, using scanning electron microscopy. In case of blends with higher content of PS‐g‐PA6 copolymer, copolymer nanoparticles coexisting with the PS formed the matrix, in which PA6 microspheres were dispersed evenly as minor phase. The content of the compositions (homopolystyrene, homopolyamide 6, and PS‐g‐PA6) of the blends were determined by selective solvent extraction technique. The mechanical properties of PA6/PS‐g‐PA6/PS blends were better than that of PA6/PS blends. Especially for the blends T10 with lower PS‐g‐PA6 copolymer content, both the flexural strength and flexural modulus showed significantly improving because of the improved interfacial adhesion between PS and PA6. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Stress–strain behavior and impact strength of polystyrene/polyamide-6 blends compatibilized with poly(styrene-g-ethylene oxide)

The mechanical properties of polystyrene/polyamide-6 (50/50 wt/wt) blends were improved by additions of small amounts of poly(styrene-g-ethylene oxide) (SEO) during compounding by extrusion. Tensile testing of injection-molded samples revealed that the blends developed a yield point after addition of 1 wt % SEO. The elongation at break increased by almost a factor of 6, and the impact strength increased by a factor of 1.5 after adding 3 wt % SEO. Morphological analysis by electron microscopy showed that additions of SEO resulted in decreased domain sizes, and seemed to promote interfacial adhesion. The morphologies of the compatibilized blends also had a higher degree of anisotropy, as compared with the uncompatibilized blend. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1887–1891, 1998     

The mechanical and rheological behavior of the PA/TPU blend with POE‐g‐MA modifier

In this research, we attempt to improve the impact strength and the viscosity of PA (polyamide) by blending two elastomers, TPU (thermoplastic polyurethane) and POE‐g‐MA (maleic anhydride‐grafted polyethylene‐octene elastomer), in PA matrix with twin screw extruder. The ratio of blending is 80PA/20TPU and 80PA/20TPU/20POE‐g‐MA (66.66PA/16.67TPU/16.67POE‐g‐MA). Results indicate that POE‐g‐MA improves the low viscosity of PA and TPU during the blending process, and also their compatibility. Thus, the 80PA/20TPU/20POE‐g‐MA blend has better tensile stress and elongation than 80PA/20TPU blend, and furthermore POE‐g‐MA significantly improves the impact strength of PA, even to super‐toughness grade. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Reactive compatibilization of PE/PS blends. Effect of copolymer chain length on interfacial adhesion and mechanical behavior

This paper deals with in situ compatibilization of PE/PS blends via Friedel-Crafts reaction, performed at the interphase. Two polyethylenes having different molecular weights, and the same PS, were used along a wide range of catalyst concentration. The influence of the graft copolymer architecture and content on the efficiency of blend compatibilization was studied. The emulsifying effect, morphological aspects and mechanical behavior were also assessed for these blends. The amount of copolymer formed increases with catalyst concentration and the short chain length fraction of the homopolymers. The high molecular weight (MW) copolymers behaved as better compatibilizers as they showed, at the cmc, greater graft copolymer concentration than the low MW ones. A substantial increase in interfacial adhesion and particle size reduction was observed, even at catalyst concentrations as low as 0.3 wt%. In correspondence, mechanical properties, like ductility and yield strength, were enhanced by the effect of this Friedel-Crafts reaction's compatibilization.     

The morphology and mechanical properties of dynamic packing injection molded PP/PS blends

As a part of long-term project aimed at super polyolefin blends, in this work, we report the mechanical reinforcement and phase morphology of the immiscible blends of polypropylene (PP) and polystyrene (PS) achieved by dynamic packing injection molding (DPIM). The shear stress (achieved by DPIM) and interfacial interaction (obtained by using styrene-butadiene-styrene (SBS) as a compatibilizer) have a great effect on phase morphology thus mechanical properties. The shear-induced morphology with core in the center and oriented zone surrounding the core was observed in the cross-section areas of the samples. The phase inversion was also found to shift towards lower PS content under shear stress, at 70 wt% in the core and 30 wt% in the oriented zone, compared with 80 wt% for static samples (without shear). The tensile strength, tensile modules and impact strength were found largely increase by means of either shear stress or compatibilizer. The PS particle size is greatly reduced with adding of SBS, and the reduced particle size results in greater resistance to deformation, which causes the co-continuous structure at oriented zone change into droplet morphology. The morphology resulting from blending and processing was discussed based on effect of interfacial tension, shear rate, phase viscosity ratio and composition. The observed change of mechanical properties was explained based on the combined effect of phase morphology (droplet-matrix or co-continuous phase) and molecular orientation under shear stress.     

A study on the effects of SEBS‐g‐MAH on the phase morphology and mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends

In this work, five ternary blends based on 70% by weight (wt %) of polypropylene (PP) with 30% wt of polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene)(SEBS) dispersed phase consists of 15 wt % PC and 15 wt % reactive (maleic anhydride grafted) and nonreactive SEBS mixtures at various ratios were prepared in a co‐rotating twin screw extruder. scanning electron microscopy (SEM) micrographs showed that the blends containing only nonreactive SEBS exhibited a fine dispersion of core‐shell particles. With decreasing the SEBS/SEBS‐g‐Maleic Anhydride (MAH) weight ratio, the morphology changed from the core‐shell particles to a mixed of core‐shell, rod‐like and individual particles. This variation in phase morphology affected the thermal and mechanical properties of the blends. DSC results showed that the blends containing only nonreactive SEBS exhibited a minimum in degree of crystallinity due to the homogeneous nucleation of core‐shell particles. Mechanical testing showed that in the SEBS/SEBS‐g‐MAH weight ratio of 50/50, the modulus and impact strength increased compared with the PP matrix while the yield stress had minimum difference with that of PP matrix. These effects could be attributed to the formation of those especial microstructures revealed by the SEM studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Chemical modification of polymer blends by reactive processing: In situ reactions of interlinking agents in PS/EPDM blends

Polystyrene (PS) and the ethylene–propylene–ethylidene norbornene terpolymer (EPDM) were melt-processed in the presence of multifunctional interlinking agents, divinylbenzene (DVB) and trimethylolpropane triacrylate (TRIS), in an internal mixer to promote functionalization of the polymers and target in situ formation of the interpolymer product via coreaction of the functionalities. This approach leads to effective in situ compatibilization of the otherwise incompatible polymer components of the blends. The weight ratio of PS/EPDM and the concentration of the interlinking agents were kept constant at 70/30 and 5%, respectively. The effect of varying the concentration of the free-radical initiator (a peroxide) and the method of its addition during melt processing on the overall reaction outcome was also examined. Changes in torque during the melt-processing operation was monitored. Sequential extraction of the polymer blends was used to separate and characterize the insoluble fraction (interpolymer). Changes in the thermal behavior (shifts in glass transition temperatures) of both the polymer blends and their insoluble fractions was investigated together with an examination of the morphology and mechanical properties of the reactively processed blends. It was found that the use of mixed reactive interlinking agents in a one-step reactive blending process and the enhancement of PS reactivity via preinitiation before addition of the reactive agents led to an increase in the extent of the coupling reaction between the functionalized PS and EPDM. This results in the formation of an “across-phase” interpolymer with an optimum composition that is responsible for the significant changes observed in the morphology and associated improvements in the mechanical properties of the blend samples. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1933–1951, 1998     

Effect of blending sequence on the morphology and properties of polyamide 6/EPDM‐g‐MA/epoxy blends

The ternary blends of polyamide 6/maleated ethylene‐propylene‐diene rubber/epoxy (PA6/EPDM‐g‐MA/EP) were prepared by a twin‐screw extruder with four different blending sequences. With the variation of blending sequence, the ternary blends presented distinct morphology and mechanical properties because of different interactions induced by various reactive orders. The addition of epoxy could increase the viscosity of the PA6 matrix, but a considerably larger size of the dispersed rubber phase was observed while first preblending PA6 with epoxy followed by blending a premix of PA6/EP with EDPM‐g‐MA, which was attested by rheological behaviors and SEM observations. It was probably ascribed to the fact that the great increase of the interfacial tension between the matrix and rubber phase aroused a great coalescence of rubber particles. The presence of epoxy in the rubber phase reduced the rubber's ability to cavitate so that the toughening efficiency of the EPDM‐g‐MA was decreased. The results of mechanical testing revealed that the optimum blending sequence to achieve balanced mechanical properties is blending PA6, EPDM‐g‐MA, and epoxy simultaneously in which the detrimental reactions might be effectively suppressed. In addition, thermal properties were investigated by TG and DSC, and the results showed that there was no distinct difference. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011