Incorporation of epoxidized soybean oil as co‐matrix in epoxy resin toward developing plastisol/particulate toughened glass fiber composites

Epoxidized soybean oil was incorporated as a co‐matrix into an epoxy resin, and the hybrid resin system was used for preparing glass fiber‐reinforced composites. Effect of addition of poly(vinyl chloride) plastisol and selected particulate fillers (fly ash and wood flour) to epoxy/epoxidized soybean oil matrix on mechanical and water uptake properties of glass fiber‐reinforced composites were studied. Fourier transform infrared spectroscopy was used to reveal the curing state of these composites. It was observed that tensile strengths and moduli decreased with the inclusion of all additives. However, addition of poly(vinyl chloride) plastisol, fly ash, and wood flour particulate fillers showed significant increase in impact strengths compared with neat epoxy composite in a synergistic manner. Water uptake results of the composites were found to be in good agreement with ? OH peak intensities obtained from Fourier transform infrared spectroscopy. Finally, acousto‐ultrasonic nondestructive technique was successfully used to assess damage states and to relate stress wave factors with tensile strength properties of modified epoxy‐based glass fiber composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40586.     

5528氰酸酯树脂基玻璃纤维增强复合材料性能研究

本文对新型的5528改性氰酸酯树脂基玻璃纤维增强复合材料的耐热性能、力学性能、耐湿热性能、介电性能进行研究，结果表明：5528氰酸酯树脂基玻璃纤维增强复合材料具有良好的力学性能和介电性能。其中石英玻璃纤维增强复合材料的介电常数为3．40，介电损耗正切值为0．00393，并且对频率显示出优秀的稳定性；而高强玻璃纤维增强复合材料的介电损耗正切值为0．00925，远远优于环氧和双马树脂基复合材料。5528氰酸酯基玻璃纤维复合材料适合高性能透波材料或高频印刷电路板应用。     

RTM制备玻璃纤维增强环氧树脂复合材料的力学性能分析

以环氧树脂为基体,短切玻璃纤维和玻璃纤维布为增强材料,通过RTM工艺制备了玻璃纤维增强环氧树脂(GF/EP)复合材料,并研究了RTM工艺制备玻璃纤维布增强环氧树脂(L-GF/EP)和短切玻璃纤维增强环氧树脂(S-GF/EP)复合材料的拉伸和弯曲性能,分析了开孔对两种复合材料拉伸性能的影响。结果表明:在拉伸过程中,开孔试样因孔边产生的应力集中,导致其拉伸强度与无孔试样相比下降了30%左右;玻纤铺层类型的不同对复合材料的力学性能具有显著影响;L-GF/EP复合材料内部结构完整,在载荷作用下,复合材料的弯曲断裂呈现一定的假塑性断裂模式,达到弯曲极限挠度值后,出现一定程度的回弹现象,其力学性能优于S-GF/EP复合材料。     

深潜壳体用高模量树脂基体的研究——基体模量对复合材料抗压抗剪性能的影响

制备了高模量树脂基单向复合材料，测试了单向复合材料的纵向压缩性能和平面剪切性能。研究了基体模量对单向复合材料抗压强度及复合材料平面剪切性能的影响，结果表明：单向复合材料的抗压强度与基体模量成线性比例关系，随基体模量的提高而提高，复合材料的平面剪切性能与基体模量基本上呈线性关系，平面剪切强度亦随基体模量的提高而提高。以模量达５．３６ＧＰａ的环氧树脂作为复合材料的树脂基体制备的，单向玻璃纤维增强复合材料其抗压强度高达１．２９５ＧＰａ，碳纤维增强的复合材料抗压强度高达１．３７２ＧＰａ，与普通环氧树脂的单向复合材料相比，分别提高了５５％和４５．８％；复合材料的平面剪切强度达６４．５ＭＰａ，比普通环氧树脂复合材料的平面剪切强度提高了４４．３％，满足了深潜壳体对复合材料抗压强度的要求。     

Comparison of the role of milled glass and carbon fibers on mechanical properties of (bisphenol A)‐based epoxy composites

The main target of the current work was to study the mechanical properties of milled E‐glass, S‐glass, and high‐strength (carbon fiber)‐reinforced epoxy composites. At first, tensile behavior of the as‐received fibers was evaluated by conducting different tensile tests. Afterwards, the effects of employing an integral blended coupling agent on the performance of the pure epoxy were investigated by microhardness tests and optical microscopic images. Then, the epoxy composites were prepared simply by mixing and stirring 1, 3, and 5 wt% of the milled fibers with the epoxy resin and its hardener. The effects of mixture degassing and addition of the coupling agent to the mixture were examined based on the mechanical properties of the fabricated composites. Also, scanning electron microscope macro‐ and micrographs of the transverse and longitudinal fracture surfaces were used to study the fracture behavior and identify the active toughening mechanisms. The best results were obtained for the degassed and modified milled (carbon fiber epoxy)‐reinforced composite, which enhanced the tensile strength, elongation, Young's modulus, and toughness up to 12%, 17%, 19%, and 27%, respectively. The current study shows that the composite not only is cost effective but also offers better mechanical properties. J. VINYL ADDIT. TECHNOL., 24:130–138, 2018. © 2016 Society of Plastics Engineers     

Mechanical,thermal, and burning properties of viscose fabric composites: Influence of epoxy resin modification

The influence of epoxy resin modification by 3‐aminopropyltriethoxysilane (APTES) on various properties of warp knitted viscose fabric is reported in this study. Dynamic mechanical, impact resistance, flexural, thermal properties, and burning behavior of the epoxy/viscose fabric composites are studied with respect to varying content of silane coupling agent. The results obtained for APTES‐modified epoxy resin based composites reinforced with unmodified viscose fabric composites are compared to unmodified epoxy resin based composites reinforced with APTES‐modified viscose fabric. The dynamic mechanical behavior of the APTES‐modified resin based composites indicates improved interfacial adhesion. The composites prepared from modified epoxy resin exhibited a twofold increase in impact resistance. The improved adhesion between the fiber and modified resin was also visible from the scanning electron microscope analysis of the impact fracture surface. There was less influence of resin modification on the flexural properties of the composites. The 5% APTES modification induced early degradation of composites compared to all other composites. The burning rate of all the composites under study is rated to be satisfactory for use in automotive interior applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46673.     

Unsaturated polyester‐toughened epoxy composites: Effect of sisal fiber on thermal and dynamic mechanical properties

In the present study, the mechanical and thermal properties of sisal fiber‐reinforced unsaturated polyester (UP)‐toughened epoxy composites were investigated. The sisal fibers were chemically treated with alkali (NaOH) and silane solutions in order to improve the interfacial interaction between fibers and matrix. The chemical composition of resins and fibers was identified by using Fourier‐transform infrared spectroscopy. The UP‐toughened epoxy blends were obtained by mixing UP (5, 10, and 15 wt%) into the epoxy resin. The fiber‐reinforced composites were prepared by incorporating sisal fibers (10, 20, and 30 wt%) within the optimized UP‐toughened epoxy blend. Scanning electron microscopy was used to analyze the morphological changes of the fibers and the adhesion between the fibers and the UP‐toughened epoxy system. The results showed that the tensile and flexural strength of (alkali‐silane)‐treated fiber (30 wt%) ‐reinforced composites increased by 83% and 55%, respectively, as compared with that of UP‐toughened epoxy blend. Moreover, thermogravimetric analysis revealed that the (alkali‐silane)‐treated fiber and its composite exhibited higher thermal stability than the untreated and alkali‐treated fiber systems. An increase in storage modulus and glass transition temperature was observed for the UP‐toughened epoxy matrix on reinforcement with treated fibers. The water uptake behavior of both alkali and alkali‐silane‐treated fiber‐reinforced composites is found to be less as compared with the untreated fiber‐reinforced composite. J. VINYL ADDIT. TECHNOL., 23:188–199, 2017. © 2015 Society of Plastics Engineers     

Mechanical properties of hybrid structural composites reinforced with nanosilica

Epoxy‐based hybrid structural composites reinforced with 14 nm spherical silica particles were investigated for mechanical properties as a function of nanosilica loading fractions. Composites were fabricated using continuous glass or carbon fiber of unidirectional architecture and nanosilica dispersed epoxy, through resin film infusion process. Uniform dispersion of nanoparticles in resin matrix was ensured by an optimized ultrasound‐assisted process. Although resin viscosity marginally reduces in the presence of nanosilica enabling a better control in composite manufacturing process, glass transition temperature of epoxy remained unaffected at low weight fractions. Compressive strength of hybrid glass or carbon fiber/epoxy composites showed more than 30–35% increase with nanosilica at a concentration as low as 0.2 wt%. Tensile and compressive properties of hybrid composites in transverse direction to the reinforcement remained unaffected. POLYM. COMPOS. 37:1216–1222, 2016. © 2014 Society of Plastics Engineers     

长玻璃纤维增强聚丙烯复合材料的力学性能研究

采用熔体浸渍技术制备了长玻璃纤维母料(LGF/PP-g-MAH/PP)增强聚丙烯(PP)复合材料(LGF/PP)。通过双螺杆挤出机制备了同等配比的短玻纤增强聚丙烯(SGF/PP)复合材料。研究了LGF含量、环氧树脂(EP)和固化剂(2E4MZ)对LGF/PP复合材料的力学性能影响。结果表明:当LGF质量分数为35%～40%时,LGF/PP的综合力学性能最好,且明显优于同样组成的SGF/PP复合材料。EP和含固化剂(2E4MZ)的EP对LGF/PP复合材料的力学性能提高有一定的作用。SEM照片分析表明:EP的加入能改善玻纤与聚丙烯基体的界面粘接。     

Surface modification and physical properties of various UHMWPE‐fiber‐reinforced modified epoxy composites

Two surface modification methods—plasma surface treatment and chemical agent treatment—were used to investigate their effects on the surface properties of ultrahigh‐molecular‐weight polyethylene (UHMWPE) fibers. In the analyses, performed using electron spectroscopy for chemical analysis, changes in weight, and scanning electron microscope observations, demonstrated that the two fiber‐surface‐modified composites formed between UHMWPE fiber and epoxy matrix exhibited improved interfacial adhesion and slight improvements in tensile strengths, but notable decreases in elongation, relative to those properties of the composites reinforced with the untreated UHMWPE fibers. In addition, three kinds of epoxy resins—neat DGEBA, polyurethane‐crosslinked DGEBA, and BHHBP‐DGEBA—were used as resin matrices to examine the tensile and elongation properties of their UHMWPE fiber‐reinforced composites. From stress/strain measurements and scanning electron microscope observations, the resin matrix improved the tensile strength apparently, but did not affect the elongation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 655–665, 2007     

环氧树脂/空心玻璃微珠泡沫材料性能研究

以高强度环氧树脂为基体,表面改性处理的空心玻璃微珠(HGB)为填料,经高温固化制备了环氧树脂/HGB泡沫材料,并研究了HGB类型、HGB含量和固化剂用量对泡沫材料压缩性能的影响。研究发现,随着HGB填充量的增大,泡沫材料的密度和压缩强度均下降。当固化剂与环氧树脂物质的量比为0.85时,泡沫材料的抗压性能最好,压缩强度为40.19 MPa。偶联剂改性HGB可以有效改善HGB和基体树脂的粘合效果。当改性HGB质量分数为80%时,与未改性环氧树脂相比,环氧树脂/改性HGB泡沫材料压缩强度提高了5.0%,吸水率下降40.6%。     

香蕉纤维的表面改性及其增强环氧树脂复合材料的性能研究

采用硅烷偶联剂(A-174)偶联、高锰酸钾接枝和乙酰化包覆等3种方法对香蕉纤维进行表面改性,制备了改性香蕉纤维增强环氧树脂复合材料,测试其拉伸、弯曲、压缩、冲击等力学性能。结果表明,偶联、接枝、包覆等表面改性均能明显改善香蕉纤维与基体树脂的相容性,提高复合材料的力学性能,其中偶联改性的效果最好。当改性香蕉纤维含量为10wt%时,与未改性的香蕉纤维比较,复合材料的拉伸强度、弯曲强度、压缩强度分别提高了1.8、1.0、2.6倍;随着纤维含量的增加,复合材料的力学性能明显提高。     

Tensile behavior of glass‐fiber‐filled polyacetal: Influence of the functional groups of polymer matrices

We investigated the tensile behavior of glass‐fiber‐filled polyacetal [i.e., polyoxymethylene (POM)], focusing on the mutual influence of the functional groups in the POM matrices and the glass binder system. The different POM matrices were compounded with three kinds of glass fibers (20 wt %) treated with different glass binders, namely, epoxy resin, thermoplastic polyurethane (TPU), and a mixture of TPU and epoxy resin. A good correlation between the tensile strength and elongation at break was observed, regardless of the difference in the glass binders. The composites based on the modified POM matrix, which had both a carboxyl end group and a hydroxyl end group, improved the tensile properties noticeably in comparison with those based on the normal POM matrix. The composites were strengthened with an increase in the concentration of the functional groups. The results of scanning electron microscopy observations indicated that the fractured surfaces of a specimen having maximum tensile strength and elongation exhibited cohesion of the modified POM on the surfaces of the glass fibers. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

BMI Based Composites With Low Dielectric Loss

Summary O,O’-diallylbisphenol A (BA), allyl epoxy resins and epoxy acrylate resins are adopted to copolymerize with 4,4’-bismaleimidodiphenyl methane (BDM) resins and modify mechanical properties and processing charicteristics. The new modified BMI resin systems have more than two times improved impact strength without a great decrease in excellent dielectric properties or thermal and hot–wet resistance of neat BDM resin. Composites based on modified BMI resins and reinforced by glass fibre and quartz fibre possess excellent mechanical properties. The fracture surfaces of the composites are examined by scanning electron microscopy (SEM). It is indicted that modified BMI resin matrix composites put up typical toughness rupture and the adhesion efficiency in interface of composites is fine. When the test frequency scope is from 1 GHz to 20 GHz, the dielectric constant and dielectric loss of composites almost hold the line. After 100 h in boil water, mechanical and dielectric properties of composites are higher than 85% retention of their original values.     

Mechanical and thermal properties of hierarchical composites enhanced by pristine graphene and graphene oxide nanoinclusions

Epoxy resin nanocomposites incorporated with 0.5, 1, 2, and 4 wt % pristine graphene and modified graphene oxide (GO) nanoflakes were produced and used to fabricate carbon fiber‐reinforced and glass fiber‐reinforced composite panels via vacuum‐assisted resin transfer molding process. Mechanical and thermal properties of the composite panels—called hierarchical graphene composites—were determined according to ASTM standards. It was observed that the studied properties were improved consistently by increasing the amount of nanoinclusions. Particularly, in the presence of 4 wt % GO in the resin, tensile modulus, compressive strength, and flexural modulus of carbon fiber (glass fiber) composites were improved 15% (21%), 34% (84%), and 40% (68%), respectively. Likewise, with inclusion of 4 wt % pristine graphene in the resin, tensile modulus, compressive strength, and flexural modulus of carbon fiber (glass fiber) composites were improved 11% (7%), 30% (77%), and 34% (58%), respectively. Also, thermal conductivity of the carbon fiber (glass fiber) composites with 4% GO inclusion was improved 52% (89%). Similarly, thermal conductivity of the carbon fiber (glass fiber) composites with 4% pristine graphene inclusion was improved 45% (80%). The reported results indicate that both pristine graphene and modified GO nanoflakes are excellent options to enhance the mechanical and thermal properties of fiber‐reinforced polymeric composites and to make them viable replacement materials for metallic parts in different industries, such as wind energy, aerospace, marine, and automotive. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40826.     

玻纤增强ABS复合材料的制备及性能

以丙烯腈-丁二烯-苯乙烯共聚物(ABS)及玻璃纤维(GF)为原料,以环氧树脂作为界面相容剂,研究了界面相容剂对玻璃纤维增强ABS复合材料力学性能及界面粘接的影响.结果表明:加入环氧树脂,玻纤增强ABS复合材料的力学性能明显提高;随着玻纤质量分数的增加,复合材料的拉伸强度、弯曲强度、冲击强度均逐渐增加;玻纤质量分数为30%时,GF/ABS/环氧树脂复合材料的拉伸强度比未改性的复合材料的拉伸强度提高了30%,弯曲强度提高了25%,冲击强度也提高了50%.     

聚丙烯/马来酸酐接枝聚丙烯/环氧树脂/玻璃纤维复合材料的制备及其性能研究

通过双螺杆挤出机制备了聚丙烯/马来酸酐接枝聚丙烯/环氧树脂/玻璃纤维（PP/PP-g-MAH/EP/GF）复合材料,并研究了PP-g-MAH含量、EP含量及固化剂对复合材料力学性能的影响。结果表明,PP-g-MAH含量为10份,含有固化剂EP的含量为3份时,复合材料的综合力学性能最佳;与不加EP的复合材料相比,其拉伸强度、弯曲强度、冲击强度分别提高了41 %、47 %、86 %。扫描电子显微镜分析表明,EP的加入明显改善了GF和PP基体的黏结强度。     

Mechanical properties of poly(styrene‐co‐acrylonitrile)‐modified epoxy resin/glass fiber composites

Poly(styrene‐co‐acylonitrile) was used to modify diglycedyl ether of bisphenol‐A type epoxy resin cured with diamino diphenyl sulfone and the modified epoxy resin was used as the matrix for fiber‐reinforced composites (FRPs) to get improved mechanical properties. E‐glass fiber was used as fiber reinforcement. The tensile, flexural, and impact properties of the blends and composites were investigated. The blends exhibited considerable improvement in mechanical properties. The scanning electron micrographs of the fractured surfaces of the blends and tensile fractured surfaces of the composites were also analyzed. The micrographs showed the influence of morphology on the properties of blends. Results showed that the mechanical properties of glass FRPs increased gradually upon fiber loading. Predictive models were applied using various equations to compare the mechanical data obtained theoretically and experimentally. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of novolac resin modification on mechanical properties of carbon fiber/epoxy composites

The epoxy resin matrix of carbon fiber (CF)‐reinforced epoxy composites was modified with novolac resin (NR) to improve the matrix‐dominated mechanical properties of composites. Flexural strength, interlaminar shear strength (ILSS), and impact strength were measured with unfilled, 7 wt% NR, 13 wt% NR, and 18 wt% NR filled to epoxy to identify the effect of adding NR on the mechanical properties of composites. The results showed that both interfacial and impact properties of composites were improved except for flexural property. The largest improvement in ILSS and impact strength were obtained with 13 wt% loading of NR. ILSS and impact strength were improved by 7.3% and 38.6%, respectively, compared with the composite without NR. The fracture and surface morphologies of the composite specimens were characterized by scanning electron microscopy. Intimate bonding of the fibers and the matrix was evident with the content of 7–13 wt% NR range. Decrease of crosslinking density and formation of NR transition layer were deduced with adding NR. POLYM. COMPOS., 2011. © 2010 Society of Plastics Engineers     

Improved thermomechanical properties of carbon fiber reinforced epoxy composite using amino functionalized XDCNT

Carbon fiber‐reinforced epoxy composites (CFEC) are fabricated infusing up to 0.40 wt % amino‐functionalized XD‐grade carbon nanotubes (XDCNT) using the compression molding process. Interlaminar shear strength (ILSS) and thermomechanical properties of these composites are evaluated through short beam shear and dynamic–mechanical thermal analysis tests. XDCNTs are infused into Epon 862 resin using a mechanical stirrer followed by sonication. After the sonication, the mixture was placed in a three roll milling processor for three successive cycles at 140 rpm for uniform dispersion of CNTs. Epikure W curing agent was then added to the resin using a high‐speed mechanical stirrer. Finally, the fiber was reinforced with the modified resin using the compressive mold. ILSS was observed to increase by 22% at 0.3 wt % XDCNT loading. Thermal properties, including storage modulus, glass transition temperature, and crosslink density demonstrated linear enhancement up to the 0.3 wt % XDCNT loading. Scanning electron microscopy revealed better interfacial bonding in the CNT‐loaded CFEC. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40709.